MMC: OMAP: Power functions modified to MMC multislot support

Modifications at power functions to MMC multislot support. This patch
also move board-specific code out of MMC OMAP driver.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This commit is contained in:
Juha Yrjola 2008-03-26 16:09:22 -04:00 committed by Pierre Ossman
parent b8f9f0e90a
commit 65b5b6e51b

View File

@ -983,52 +983,27 @@ static void mmc_omap_request(struct mmc_host *mmc, struct mmc_request *req)
mmc_omap_start_request(host, req);
}
static void innovator_fpga_socket_power(int on)
static void mmc_omap_set_power(struct mmc_omap_slot *slot, int power_on,
int vdd)
{
#if defined(CONFIG_MACH_OMAP_INNOVATOR) && defined(CONFIG_ARCH_OMAP15XX)
if (on) {
fpga_write(fpga_read(OMAP1510_FPGA_POWER) | (1 << 3),
OMAP1510_FPGA_POWER);
} else {
fpga_write(fpga_read(OMAP1510_FPGA_POWER) & ~(1 << 3),
OMAP1510_FPGA_POWER);
}
#endif
}
struct mmc_omap_host *host;
/*
* Turn the socket power on/off. Innovator uses FPGA, most boards
* probably use GPIO.
*/
static void mmc_omap_power(struct mmc_omap_host *host, int on)
{
if (on) {
if (machine_is_omap_innovator())
innovator_fpga_socket_power(1);
else if (machine_is_omap_h2())
tps65010_set_gpio_out_value(GPIO3, HIGH);
else if (machine_is_omap_h3())
/* GPIO 4 of TPS65010 sends SD_EN signal */
tps65010_set_gpio_out_value(GPIO4, HIGH);
else if (cpu_is_omap24xx()) {
u16 reg = OMAP_MMC_READ(host, CON);
OMAP_MMC_WRITE(host, CON, reg | (1 << 11));
} else
if (host->power_pin >= 0)
omap_set_gpio_dataout(host->power_pin, 1);
} else {
if (machine_is_omap_innovator())
innovator_fpga_socket_power(0);
else if (machine_is_omap_h2())
tps65010_set_gpio_out_value(GPIO3, LOW);
else if (machine_is_omap_h3())
tps65010_set_gpio_out_value(GPIO4, LOW);
else if (cpu_is_omap24xx()) {
u16 reg = OMAP_MMC_READ(host, CON);
OMAP_MMC_WRITE(host, CON, reg & ~(1 << 11));
} else
if (host->power_pin >= 0)
omap_set_gpio_dataout(host->power_pin, 0);
host = slot->host;
if (slot->pdata->set_power != NULL)
slot->pdata->set_power(mmc_dev(slot->mmc), slot->id, power_on,
vdd);
if (cpu_is_omap24xx()) {
u16 w;
if (power_on) {
w = OMAP_MMC_READ(host, CON);
OMAP_MMC_WRITE(host, CON, w | (1 << 11));
} else {
w = OMAP_MMC_READ(host, CON);
OMAP_MMC_WRITE(host, CON, w & ~(1 << 11));
}
}
}
@ -1067,23 +1042,31 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
int i, dsor;
dsor = mmc_omap_calc_divisor(mmc, ios);
host->bus_mode = ios->bus_mode;
host->hw_bus_mode = host->bus_mode;
mmc_omap_select_slot(slot, 0);
if (ios->vdd != slot->vdd)
slot->vdd = ios->vdd;
switch (ios->power_mode) {
case MMC_POWER_OFF:
mmc_omap_power(host, 0);
mmc_omap_set_power(slot, 0, ios->vdd);
break;
case MMC_POWER_UP:
/* Cannot touch dsor yet, just power up MMC */
mmc_omap_power(host, 1);
return;
mmc_omap_set_power(slot, 1, ios->vdd);
goto exit;
case MMC_POWER_ON:
dsor |= 1 << 11;
break;
}
clk_enable(host->fclk);
if (slot->bus_mode != ios->bus_mode) {
if (slot->pdata->set_bus_mode != NULL)
slot->pdata->set_bus_mode(mmc_dev(mmc), slot->id,
ios->bus_mode);
slot->bus_mode = ios->bus_mode;
}
/* On insanely high arm_per frequencies something sometimes
* goes somehow out of sync, and the POW bit is not being set,
@ -1091,6 +1074,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
* Writing to the CON register twice seems to do the trick. */
for (i = 0; i < 2; i++)
OMAP_MMC_WRITE(host, CON, dsor);
slot->saved_con = dsor;
if (ios->power_mode == MMC_POWER_ON) {
/* Send clock cycles, poll completion */
OMAP_MMC_WRITE(host, IE, 0);
@ -1099,7 +1083,9 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
while ((OMAP_MMC_READ(host, STAT) & 1) == 0);
OMAP_MMC_WRITE(host, STAT, 1);
}
clk_disable(host->fclk);
exit:
mmc_omap_release_slot(slot);
}
static const struct mmc_host_ops mmc_omap_ops = {