lk/linux-kernel-test
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

USB: remove URB_NO_SETUP_DMA_MAP

Browse Source 
Now that URB_NO_SETUP_DMA_MAP is no longer in use, this patch (as1376)
removes all references to it.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit is contained in:
Alan Stern
2010-04-30 16:35:37 -04:00
committed by Greg Kroah-Hartman
parent 842f16905d
commit 85bcb5ee88
4 changed files with 19 additions and 32 deletions
Download Patch File Download Diff File Expand all files Collapse all files

28
include/linux/usb.h
View File

@@ -953,7 +953,6 @@ extern int usb_disabled(void);
#define URB_ISO_ASAP 0x0002 /* iso-only, urb->start_frame
* ignored */
#define URB_NO_TRANSFER_DMA_MAP 0x0004 /* urb->transfer_dma valid on submit */
#define URB_NO_SETUP_DMA_MAP 0x0008 /* urb->setup_dma valid on submit */
#define URB_NO_FSBR 0x0020 /* UHCI-specific */
#define URB_ZERO_PACKET 0x0040 /* Finish bulk OUT with short packet */
#define URB_NO_INTERRUPT 0x0080 /* HINT: no non-error interrupt
@@ -1049,12 +1048,8 @@ typedef void (*usb_complete_t)(struct urb *);
* @setup_packet: Only used for control transfers, this points to eight bytes
* of setup data. Control transfers always start by sending this data
* to the device. Then transfer_buffer is read or written, if needed.
* @setup_dma: For control transfers with URB_NO_SETUP_DMA_MAP set, the
* device driver has provided this DMA address for the setup packet.
* The host controller driver should use this in preference to
* setup_packet, but the HCD may chose to ignore the address if it must
* copy the setup packet into internal structures. Therefore, setup_packet
* must always point to a valid buffer.
* @setup_dma: DMA pointer for the setup packet. The caller must not use
* this field; setup_packet must point to a valid buffer.
* @start_frame: Returns the initial frame for isochronous transfers.
* @number_of_packets: Lists the number of ISO transfer buffers.
* @interval: Specifies the polling interval for interrupt or isochronous
@@ -1086,13 +1081,14 @@ typedef void (*usb_complete_t)(struct urb *);
* bounce buffer or talking to an IOMMU),
* although they're cheap on commodity x86 and ppc hardware.
*
* Alternatively, drivers may pass the URB_NO_xxx_DMA_MAP transfer flags,
* which tell the host controller driver that no such mapping is needed since
* Alternatively, drivers may pass the URB_NO_TRANSFER_DMA_MAP transfer flag,
* which tells the host controller driver that no such mapping is needed for
* the transfer_buffer since
* the device driver is DMA-aware. For example, a device driver might
* allocate a DMA buffer with usb_alloc_coherent() or call usb_buffer_map().
* When these transfer flags are provided, host controller drivers will
* attempt to use the dma addresses found in the transfer_dma and/or
* setup_dma fields rather than determining a dma address themselves.
* When this transfer flag is provided, host controller drivers will
* attempt to use the dma address found in the transfer_dma
* field rather than determining a dma address themselves.
*
* Note that transfer_buffer must still be set if the controller
* does not support DMA (as indicated by bus.uses_dma) and when talking
@@ -1115,11 +1111,9 @@ typedef void (*usb_complete_t)(struct urb *);
* should always terminate with a short packet, even if it means adding an
* extra zero length packet.
*
* Control URBs must provide a setup_packet. The setup_packet and
* transfer_buffer may each be mapped for DMA or not, independently of
* the other. The transfer_flags bits URB_NO_TRANSFER_DMA_MAP and
* URB_NO_SETUP_DMA_MAP indicate which buffers have already been mapped.
* URB_NO_SETUP_DMA_MAP is ignored for non-control URBs.
* Control URBs must provide a valid pointer in the setup_packet field.
* Unlike the transfer_buffer, the setup_packet may not be mapped for DMA
* beforehand.
*
* Interrupt URBs must provide an interval, saying how often (in milliseconds
* or, for highspeed devices, 125 microsecond units)