iio: nitpicking on sysfs-bus-iio

v2: address comments by Jonathan Cameron
* add more output power down modes
* spelling of etc.

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
Peter Meerwald 2012-06-12 15:31:27 +02:00 committed by Greg Kroah-Hartman
parent 988bb033d7
commit 8b417d78ea

View File

@ -40,9 +40,9 @@ Contact: linux-iio@vger.kernel.org
Description:
Some devices have internal clocks. This parameter sets the
resulting sampling frequency. In many devices this
parameter has an effect on input filters etc rather than
parameter has an effect on input filters etc. rather than
simply controlling when the input is sampled. As this
effects datardy triggers, hardware buffers and the sysfs
effects data ready triggers, hardware buffers and the sysfs
direct access interfaces, it may be found in any of the
relevant directories. If it effects all of the above
then it is to be found in the base device directory.
@ -74,7 +74,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_raw
KernelVersion: 2.6.35
Contact: linux-iio@vger.kernel.org
Description:
Raw (unscaled no bias removal etc) voltage measurement from
Raw (unscaled no bias removal etc.) voltage measurement from
channel Y. In special cases where the channel does not
correspond to externally available input one of the named
versions may be used. The number must always be specified and
@ -118,7 +118,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_temp_z_raw
KernelVersion: 2.6.35
Contact: linux-iio@vger.kernel.org
Description:
Raw (unscaled no bias removal etc) temperature measurement.
Raw (unscaled no bias removal etc.) temperature measurement.
If an axis is specified it generally means that the temperature
sensor is associated with one part of a compound device (e.g.
a gyroscope axis). Units after application of scale and offset
@ -148,10 +148,9 @@ KernelVersion: 2.6.35
Contact: linux-iio@vger.kernel.org
Description:
Angular velocity about axis x, y or z (may be arbitrarily
assigned) Data converted by application of offset then scale to
radians per second. Has all the equivalent parameters as
per voltageY. Units after application of scale and offset are
radians per second.
assigned). Has all the equivalent parameters as per voltageY.
Units after application of scale and offset are radians per
second.
What: /sys/bus/iio/devices/iio:deviceX/in_incli_x_raw
What: /sys/bus/iio/devices/iio:deviceX/in_incli_y_raw
@ -161,7 +160,7 @@ Contact: linux-iio@vger.kernel.org
Description:
Inclination raw reading about axis x, y or z (may be
arbitrarily assigned). Data converted by application of offset
and scale to Degrees.
and scale to degrees.
What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_raw
What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_raw
@ -203,7 +202,7 @@ Contact: linux-iio@vger.kernel.org
Description:
If known for a device, offset to be added to <type>[Y]_raw prior
to scaling by <type>[Y]_scale in order to obtain value in the
<type> units as specified in <type>[y]_raw documentation.
<type> units as specified in <type>[Y]_raw documentation.
Not present if the offset is always 0 or unknown. If Y or
axis <x|y|z> is not present, then the offset applies to all
in channels of <type>.
@ -248,7 +247,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibbias
KernelVersion: 2.6.35
Contact: linux-iio@vger.kernel.org
Description:
Hardware applied calibration offset. (assumed to fix production
Hardware applied calibration offset (assumed to fix production
inaccuracies).
What /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale
@ -265,7 +264,7 @@ what /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibscale
KernelVersion: 2.6.35
Contact: linux-iio@vger.kernel.org
Description:
Hardware applied calibration scale factor. (assumed to fix
Hardware applied calibration scale factor (assumed to fix
production inaccuracies). If shared across all channels,
<type>_calibscale is used.
@ -277,7 +276,7 @@ What: /sys/.../iio:deviceX/in_capacitance_scale_available
KernelVersion: 2.635
Contact: linux-iio@vger.kernel.org
Description:
If a discrete set of scale values are available, they
If a discrete set of scale values is available, they
are listed in this attribute.
What /sys/bus/iio/devices/iio:deviceX/out_voltageY_hardwaregain
@ -321,9 +320,11 @@ Contact: linux-iio@vger.kernel.org
Description:
Specifies the output powerdown mode.
DAC output stage is disconnected from the amplifier and
1kohm_to_gnd: connected to ground via an 1kOhm resistor
100kohm_to_gnd: connected to ground via an 100kOhm resistor
three_state: left floating
1kohm_to_gnd: connected to ground via an 1kOhm resistor,
6kohm_to_gnd: connected to ground via a 6kOhm resistor,
20kohm_to_gnd: connected to ground via a 20kOhm resistor,
100kohm_to_gnd: connected to ground via an 100kOhm resistor,
three_state: left floating.
For a list of available output power down options read
outX_powerdown_mode_available. If Y is not present the
mode is shared across all outputs.
@ -342,9 +343,10 @@ KernelVersion: 2.6.38
Contact: linux-iio@vger.kernel.org
Description:
Writing 1 causes output Y to enter the power down mode specified
by the corresponding outY_powerdown_mode. Clearing returns to
normal operation. Y may be suppressed if all outputs are
controlled together.
by the corresponding outY_powerdown_mode. DAC output stage is
disconnected from the amplifier. Clearing returns to normal
operation. Y may be suppressed if all outputs are controlled
together.
What: /sys/bus/iio/devices/iio:deviceX/events
KernelVersion: 2.6.35
@ -390,12 +392,12 @@ Description:
different values, but the device can only enable both thresholds
or neither.
Note the driver will assume the last p events requested are
to be enabled where p is however many it supports (which may
vary depending on the exact set requested. So if you want to be
to be enabled where p is how many it supports (which may vary
depending on the exact set requested. So if you want to be
sure you have set what you think you have, check the contents of
these attributes after everything is configured. Drivers may
have to buffer any parameters so that they are consistent when
a given event type is enabled a future point (and not those for
a given event type is enabled at a future point (and not those for
whatever event was previously enabled).
What: /sys/.../iio:deviceX/events/in_accel_x_roc_rising_en
@ -671,7 +673,7 @@ What: /sys/.../buffer/scan_elements/in_anglvel_type
What: /sys/.../buffer/scan_elements/in_magn_type
What: /sys/.../buffer/scan_elements/in_incli_type
What: /sys/.../buffer/scan_elements/in_voltageY_type
What: /sys/.../buffer/scan_elements/in_voltage-in_type
What: /sys/.../buffer/scan_elements/in_voltage_type
What: /sys/.../buffer/scan_elements/in_voltageY_supply_type
What: /sys/.../buffer/scan_elements/in_timestamp_type
KernelVersion: 2.6.37
@ -692,7 +694,7 @@ Description:
the buffer output value appropriately. The storagebits value
also specifies the data alignment. So s48/64>>2 will be a
signed 48 bit integer stored in a 64 bit location aligned to
a a64 bit boundary. To obtain the clean value, shift right 2
a 64 bit boundary. To obtain the clean value, shift right 2
and apply a mask to zero the top 16 bits of the result.
For other storage combinations this attribute will be extended
appropriately.