From fb59ee37cfe20d10d19568899d1458a58361246c Mon Sep 17 00:00:00 2001 From: Faiz Abbas Date: Wed, 19 Jun 2019 15:54:54 +0530 Subject: [PATCH 01/15] ARM: dts: am57xx: Disable voltage switching for SD card If UHS speed modes are enabled, a compatible SD card switches down to 1.8V during enumeration. If after this a software reboot/crash takes place and on-chip ROM tries to enumerate the SD card, the difference in IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card. The fix for this is to have support for power cycling the card in hardware (with a PORz/soft-reset line causing a power cycle of the card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and am57xx-evms don't have this capability, disable voltage switching for these boards. The major effect of this is that the maximum supported speed mode is now high speed(50 MHz) down from SDR104(200 MHz). commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage switching for SD card") did this only for idk boards. Do it for all affected boards. Signed-off-by: Faiz Abbas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am571x-idk.dts | 7 +------ arch/arm/boot/dts/am572x-idk.dts | 7 +------ arch/arm/boot/dts/am574x-idk.dts | 7 +------ arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 1 + arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts | 7 +------ arch/arm/boot/dts/am57xx-beagle-x15-revc.dts | 7 +------ 6 files changed, 6 insertions(+), 30 deletions(-) diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts index 66116ad3f9f4..0a043908215c 100644 --- a/arch/arm/boot/dts/am571x-idk.dts +++ b/arch/arm/boot/dts/am571x-idk.dts @@ -178,14 +178,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; }; &mmc2 { diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts index 4f835222c266..8663a9416af6 100644 --- a/arch/arm/boot/dts/am572x-idk.dts +++ b/arch/arm/boot/dts/am572x-idk.dts @@ -19,14 +19,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; }; &mmc2 { diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts index dc5141c35610..7935d70874ce 100644 --- a/arch/arm/boot/dts/am574x-idk.dts +++ b/arch/arm/boot/dts/am574x-idk.dts @@ -24,14 +24,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_default>; - pinctrl-3 = <&mmc1_pins_hs>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_conf>; - pinctrl-6 = <&mmc1_pins_ddr50 &mmc1_iodelay_sdr104_conf>; }; &mmc2 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index 2341a56ebab9..0cdfd2853ba8 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -433,6 +433,7 @@ bus-width = <4>; cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */ + no-1-8-v; }; &mmc2 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts index 5a77b334923d..34c69965821b 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts @@ -19,14 +19,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>; vmmc-supply = <&vdd_3v3>; vqmmc-supply = <&ldo1_reg>; }; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts index 17c41da3b55f..ccd99160bbdf 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts @@ -19,14 +19,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; vmmc-supply = <&vdd_3v3>; vqmmc-supply = <&ldo1_reg>; }; From afd58b162e48076e3fe66d08a69eefbd6fe71643 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 22 Jul 2019 03:44:52 -0700 Subject: [PATCH 02/15] ARM: OMAP2+: Fix missing SYSC_HAS_RESET_STATUS for dra7 epwmss TRM says PWMSS_SYSCONFIG bit for SOFTRESET changes to zero when reset is completed. Let's configure it as otherwise we get warnings on boot when we check the data against dts provided data. Eventually the legacy platform data will be just dropped, but let's fix the warning first. Reviewed-by: Suman Anna Tested-by: Keerthy Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/omap_hwmod_7xx_data.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c index 4a5b4aee6615..1ec21e9ba1e9 100644 --- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c @@ -379,7 +379,8 @@ static struct omap_hwmod dra7xx_dcan2_hwmod = { static struct omap_hwmod_class_sysconfig dra7xx_epwmss_sysc = { .rev_offs = 0x0, .sysc_offs = 0x4, - .sysc_flags = SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET, + .sysc_flags = SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET | + SYSC_HAS_RESET_STATUS, .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART), .sysc_fields = &omap_hwmod_sysc_type2, }; From 6ee8241d17c68b94a91efabfd6bdfe63bb1b79c1 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 22 Jul 2019 03:44:42 -0700 Subject: [PATCH 03/15] bus: ti-sysc: Fix handling of forced idle For some devices we can get the following warning on boot: ti-sysc 48485200.target-module: sysc_disable_module: invalid midlemode Fix this by treating SYSC_IDLE_FORCE like we do for the other bits for idlemodes mask. Fixes: d59b60564cbf ("bus: ti-sysc: Add generic enable/disable functions") Cc: Roger Quadros Reviewed-by: Suman Anna Tested-by: Keerthy Signed-off-by: Tony Lindgren --- drivers/bus/ti-sysc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c index e6deabd8305d..78fb52e1582e 100644 --- a/drivers/bus/ti-sysc.c +++ b/drivers/bus/ti-sysc.c @@ -949,7 +949,7 @@ static int sysc_best_idle_mode(u32 idlemodes, u32 *best_mode) *best_mode = SYSC_IDLE_SMART_WKUP; else if (idlemodes & BIT(SYSC_IDLE_SMART)) *best_mode = SYSC_IDLE_SMART; - else if (idlemodes & SYSC_IDLE_FORCE) + else if (idlemodes & BIT(SYSC_IDLE_FORCE)) *best_mode = SYSC_IDLE_FORCE; else return -EINVAL; From e212abd452a4af3174fcd469d46656f83e135a19 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 22 Jul 2019 03:44:52 -0700 Subject: [PATCH 04/15] bus: ti-sysc: Fix using configured sysc mask value We have cases where there are no softreset bits like with am335x lcdc. In that case ti,sysc-mask = <0> needs to be handled properly. Tested-by: Keerthy Signed-off-by: Tony Lindgren --- drivers/bus/ti-sysc.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-) diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c index 78fb52e1582e..4963c7733554 100644 --- a/drivers/bus/ti-sysc.c +++ b/drivers/bus/ti-sysc.c @@ -1692,10 +1692,7 @@ static int sysc_init_sysc_mask(struct sysc *ddata) if (error) return 0; - if (val) - ddata->cfg.sysc_val = val & ddata->cap->sysc_mask; - else - ddata->cfg.sysc_val = ddata->cap->sysc_mask; + ddata->cfg.sysc_val = val & ddata->cap->sysc_mask; return 0; } From 2e8647bbe1c8233a20c32fd2648258f2c05c7335 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 22 Jul 2019 03:44:47 -0700 Subject: [PATCH 05/15] ARM: dts: Fix flags for gpio7 The ti,no-idle-on-init and ti,no-reset-on-init flags need to be at the interconnect target module level for the modules that have it defined. Otherwise we get the following warnings: dts flag should be at module level for ti,no-idle-on-init dts flag should be at module level for ti,no-reset-on-init Reviewed-by: Suman Anna Tested-by: Keerthy Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 2 +- arch/arm/boot/dts/dra7-evm.dts | 2 +- arch/arm/boot/dts/dra7-l4.dtsi | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index d02f5fa61e5f..df00d1756dae 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -379,7 +379,7 @@ }; }; -&gpio7 { +&gpio7_target { ti,no-reset-on-init; ti,no-idle-on-init; }; diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 714e971b912a..de7f85efaa51 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -498,7 +498,7 @@ phy-supply = <&ldousb_reg>; }; -&gpio7 { +&gpio7_target { ti,no-reset-on-init; ti,no-idle-on-init; }; diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/dra7-l4.dtsi index 23faedec08ab..63628e166c0c 100644 --- a/arch/arm/boot/dts/dra7-l4.dtsi +++ b/arch/arm/boot/dts/dra7-l4.dtsi @@ -1261,7 +1261,7 @@ }; }; - target-module@51000 { /* 0x48051000, ap 45 2e.0 */ + gpio7_target: target-module@51000 { /* 0x48051000, ap 45 2e.0 */ compatible = "ti,sysc-omap2", "ti,sysc"; ti,hwmods = "gpio7"; reg = <0x51000 0x4>, From 89bbc6f1eb90809b1538b3a9c54030c558180e3b Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 22 Jul 2019 03:44:42 -0700 Subject: [PATCH 06/15] ARM: dts: Fix incorrect dcan register mapping for am3, am4 and dra7 We are currently using a wrong register for dcan revision. Although this is currently only used for detecting the dcan module, let's fix it to avoid confusion. Tested-by: Keerthy Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am33xx-l4.dtsi | 4 ++++ arch/arm/boot/dts/am437x-l4.dtsi | 4 ++++ arch/arm/boot/dts/dra7-l4.dtsi | 4 ++-- drivers/bus/ti-sysc.c | 3 ++- 4 files changed, 12 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/am33xx-l4.dtsi index ced1a19d5f89..4bd22c1edf96 100644 --- a/arch/arm/boot/dts/am33xx-l4.dtsi +++ b/arch/arm/boot/dts/am33xx-l4.dtsi @@ -1758,6 +1758,8 @@ target-module@cc000 { /* 0x481cc000, ap 60 46.0 */ compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0xcc020 0x4>; + reg-names = "rev"; ti,hwmods = "d_can0"; /* Domains (P, C): per_pwrdm, l4ls_clkdm */ clocks = <&l4ls_clkctrl AM3_L4LS_D_CAN0_CLKCTRL 0>, @@ -1780,6 +1782,8 @@ target-module@d0000 { /* 0x481d0000, ap 62 42.0 */ compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0xd0020 0x4>; + reg-names = "rev"; ti,hwmods = "d_can1"; /* Domains (P, C): per_pwrdm, l4ls_clkdm */ clocks = <&l4ls_clkctrl AM3_L4LS_D_CAN1_CLKCTRL 0>, diff --git a/arch/arm/boot/dts/am437x-l4.dtsi b/arch/arm/boot/dts/am437x-l4.dtsi index 989cb60b9029..04bee4ff9dcb 100644 --- a/arch/arm/boot/dts/am437x-l4.dtsi +++ b/arch/arm/boot/dts/am437x-l4.dtsi @@ -1574,6 +1574,8 @@ target-module@cc000 { /* 0x481cc000, ap 50 46.0 */ compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0xcc020 0x4>; + reg-names = "rev"; ti,hwmods = "d_can0"; /* Domains (P, C): per_pwrdm, l4ls_clkdm */ clocks = <&l4ls_clkctrl AM4_L4LS_D_CAN0_CLKCTRL 0>; @@ -1593,6 +1595,8 @@ target-module@d0000 { /* 0x481d0000, ap 52 3a.0 */ compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0xd0020 0x4>; + reg-names = "rev"; ti,hwmods = "d_can1"; /* Domains (P, C): per_pwrdm, l4ls_clkdm */ clocks = <&l4ls_clkctrl AM4_L4LS_D_CAN1_CLKCTRL 0>; diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/dra7-l4.dtsi index 63628e166c0c..21e5914fdd62 100644 --- a/arch/arm/boot/dts/dra7-l4.dtsi +++ b/arch/arm/boot/dts/dra7-l4.dtsi @@ -3025,7 +3025,7 @@ target-module@80000 { /* 0x48480000, ap 31 16.0 */ compatible = "ti,sysc-omap4", "ti,sysc"; - reg = <0x80000 0x4>; + reg = <0x80020 0x4>; reg-names = "rev"; clocks = <&l4per2_clkctrl DRA7_L4PER2_DCAN2_CLKCTRL 0>; clock-names = "fck"; @@ -4577,7 +4577,7 @@ target-module@c000 { /* 0x4ae3c000, ap 30 04.0 */ compatible = "ti,sysc-omap4", "ti,sysc"; - reg = <0xc000 0x4>; + reg = <0xc020 0x4>; reg-names = "rev"; clocks = <&wkupaon_clkctrl DRA7_WKUPAON_DCAN1_CLKCTRL 0>; clock-names = "fck"; diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c index 4963c7733554..a319e1a748fe 100644 --- a/drivers/bus/ti-sysc.c +++ b/drivers/bus/ti-sysc.c @@ -1267,7 +1267,8 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = { SYSC_QUIRK("control", 0, 0, 0x10, -1, 0x40000900, 0xffffffff, 0), SYSC_QUIRK("cpgmac", 0, 0x1200, 0x1208, 0x1204, 0x4edb1902, 0xffff00f0, 0), - SYSC_QUIRK("dcan", 0, 0, -1, -1, 0xffffffff, 0xffffffff, 0), + SYSC_QUIRK("dcan", 0, 0x20, -1, -1, 0xa3170504, 0xffffffff, 0), + SYSC_QUIRK("dcan", 0, 0x20, -1, -1, 0x4edb1902, 0xffffffff, 0), SYSC_QUIRK("dmic", 0, 0, 0x10, -1, 0x50010000, 0xffffffff, 0), SYSC_QUIRK("dwc3", 0, 0, 0x10, -1, 0x500a0200, 0xffffffff, 0), SYSC_QUIRK("epwmss", 0, 0, 0x4, -1, 0x47400001, 0xffffffff, 0), From 45da5e09dd32fa98c32eaafe2513db6bd75e2f4f Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 23 Jul 2019 04:37:45 -0700 Subject: [PATCH 07/15] ARM: OMAP2+: Fix omap4 errata warning on other SoCs We have errata i688 workaround produce warnings on SoCs other than omap4 and omap5: omap4_sram_init:Unable to allocate sram needed to handle errata I688 omap4_sram_init:Unable to get sram pool needed to handle errata I688 This is happening because there is no ti,omap4-mpu node, or no SRAM to configure for the other SoCs, so let's remove the warning based on the SoC revision checks. As nobody has complained it seems that the other SoC variants do not need this workaround. Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/omap4-common.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/mach-omap2/omap4-common.c b/arch/arm/mach-omap2/omap4-common.c index b226c8aaf8b1..7074cfd1ff41 100644 --- a/arch/arm/mach-omap2/omap4-common.c +++ b/arch/arm/mach-omap2/omap4-common.c @@ -131,6 +131,9 @@ static int __init omap4_sram_init(void) struct device_node *np; struct gen_pool *sram_pool; + if (!soc_is_omap44xx() && !soc_is_omap54xx()) + return 0; + np = of_find_compatible_node(NULL, NULL, "ti,omap4-mpu"); if (!np) pr_warn("%s:Unable to allocate sram needed to handle errata I688\n", From 8613e2ca4fff764f23785eadfa54a08631ee682a Mon Sep 17 00:00:00 2001 From: Emmanuel Vadot Date: Wed, 24 Jul 2019 14:23:29 +0200 Subject: [PATCH 08/15] ARM: dts: am335x: Fix UARTs length As seen on the AM335x TRM all the UARTs controller only are 0x1000 in size. Fix this in the DTS. Signed-off-by: Emmanuel Vadot Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am33xx-l4.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/am33xx-l4.dtsi index ced1a19d5f89..a20b04b72be4 100644 --- a/arch/arm/boot/dts/am33xx-l4.dtsi +++ b/arch/arm/boot/dts/am33xx-l4.dtsi @@ -185,7 +185,7 @@ uart0: serial@0 { compatible = "ti,am3352-uart", "ti,omap3-uart"; clock-frequency = <48000000>; - reg = <0x0 0x2000>; + reg = <0x0 0x1000>; interrupts = <72>; status = "disabled"; dmas = <&edma 26 0>, <&edma 27 0>; @@ -934,7 +934,7 @@ uart1: serial@0 { compatible = "ti,am3352-uart", "ti,omap3-uart"; clock-frequency = <48000000>; - reg = <0x0 0x2000>; + reg = <0x0 0x1000>; interrupts = <73>; status = "disabled"; dmas = <&edma 28 0>, <&edma 29 0>; @@ -966,7 +966,7 @@ uart2: serial@0 { compatible = "ti,am3352-uart", "ti,omap3-uart"; clock-frequency = <48000000>; - reg = <0x0 0x2000>; + reg = <0x0 0x1000>; interrupts = <74>; status = "disabled"; dmas = <&edma 30 0>, <&edma 31 0>; @@ -1614,7 +1614,7 @@ uart3: serial@0 { compatible = "ti,am3352-uart", "ti,omap3-uart"; clock-frequency = <48000000>; - reg = <0x0 0x2000>; + reg = <0x0 0x1000>; interrupts = <44>; status = "disabled"; }; @@ -1644,7 +1644,7 @@ uart4: serial@0 { compatible = "ti,am3352-uart", "ti,omap3-uart"; clock-frequency = <48000000>; - reg = <0x0 0x2000>; + reg = <0x0 0x1000>; interrupts = <45>; status = "disabled"; }; @@ -1674,7 +1674,7 @@ uart5: serial@0 { compatible = "ti,am3352-uart", "ti,omap3-uart"; clock-frequency = <48000000>; - reg = <0x0 0x2000>; + reg = <0x0 0x1000>; interrupts = <46>; status = "disabled"; }; From 07f9a8be66a9bd86f9eaedf8f8aeb416195adab8 Mon Sep 17 00:00:00 2001 From: Faiz Abbas Date: Wed, 7 Aug 2019 16:22:38 +0530 Subject: [PATCH 09/15] ARM: dts: dra74x: Fix iodelay configuration for mmc3 According to the latest am572x[1] and dra74x[2] data manuals, mmc3 default, hs, sdr12 and sdr25 modes use iodelay values given in MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is selected and correct iodelay values can be configured. [1] http://www.ti.com/lit/ds/symlink/am5728.pdf [2] http://www.ti.com/lit/ds/symlink/dra746.pdf Signed-off-by: Faiz Abbas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi | 50 +++++++++++------------ 1 file changed, 25 insertions(+), 25 deletions(-) diff --git a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi index 28ebb4eb884a..214b9e6de2c3 100644 --- a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi +++ b/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi @@ -32,7 +32,7 @@ * * Datamanual Revisions: * - * AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016 + * AM572x Silicon Revision 2.0: SPRS953F, Revised May 2019 * AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016 * */ @@ -229,45 +229,45 @@ mmc3_pins_default: mmc3_pins_default { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ - DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ - DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ - DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ - DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ - DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ + DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ + DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ + DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ + DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ + DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ + DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ >; }; mmc3_pins_hs: mmc3_pins_hs { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ - DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ - DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ - DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ - DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ - DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ + DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ + DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ + DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ + DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ + DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ + DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ >; }; mmc3_pins_sdr12: mmc3_pins_sdr12 { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ - DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ - DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ - DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ - DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ - DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ + DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ + DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ + DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ + DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ + DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ + DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ >; }; mmc3_pins_sdr25: mmc3_pins_sdr25 { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ - DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ - DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ - DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ - DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ - DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ + DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ + DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ + DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ + DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ + DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ + DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ >; }; From fa8397e45c64e60c80373bc19ee56e42a6bed9b6 Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Sun, 11 Aug 2019 10:48:02 +0200 Subject: [PATCH 10/15] ARM: OMAP1: ams-delta-fiq: Fix missing irq_ack Non-serio path of Amstrad Delta FIQ deferred handler depended on irq_ack() method provided by OMAP GPIO driver. That method has been removed by commit 693de831c6e5 ("gpio: omap: remove irq_ack method"). Remove useless code from the deferred handler and reimplement the missing operation inside the base FIQ handler. Should another dependency - irq_unmask() - be ever removed from the OMAP GPIO driver, WARN once if missing. Signed-off-by: Janusz Krzysztofik Signed-off-by: Tony Lindgren --- arch/arm/mach-omap1/ams-delta-fiq-handler.S | 3 ++- arch/arm/mach-omap1/ams-delta-fiq.c | 4 +--- 2 files changed, 3 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-omap1/ams-delta-fiq-handler.S b/arch/arm/mach-omap1/ams-delta-fiq-handler.S index 7c9fb7fe0070..938d872b6142 100644 --- a/arch/arm/mach-omap1/ams-delta-fiq-handler.S +++ b/arch/arm/mach-omap1/ams-delta-fiq-handler.S @@ -129,6 +129,8 @@ restart: orr r11, r11, r13 @ mask all requested interrupts str r11, [r12, #OMAP1510_GPIO_INT_MASK] + str r13, [r12, #OMAP1510_GPIO_INT_STATUS] @ ack all requested interrupts + ands r10, r13, #KEYBRD_CLK_MASK @ extract keyboard status - set? beq hksw @ no - try next source @@ -136,7 +138,6 @@ restart: @@@@@@@@@@@@@@@@@@@@@@ @ Keyboard clock FIQ mode interrupt handler @ r10 now contains KEYBRD_CLK_MASK, use it - str r10, [r12, #OMAP1510_GPIO_INT_STATUS] @ ack the interrupt bic r11, r11, r10 @ unmask it str r11, [r12, #OMAP1510_GPIO_INT_MASK] diff --git a/arch/arm/mach-omap1/ams-delta-fiq.c b/arch/arm/mach-omap1/ams-delta-fiq.c index 51212133ce06..dedaf715f47c 100644 --- a/arch/arm/mach-omap1/ams-delta-fiq.c +++ b/arch/arm/mach-omap1/ams-delta-fiq.c @@ -72,9 +72,7 @@ static irqreturn_t deferred_fiq(int irq, void *dev_id) * interrupts default to since commit 80ac93c27441 * requires interrupt already acked and unmasked. */ - if (irq_chip->irq_ack) - irq_chip->irq_ack(d); - if (irq_chip->irq_unmask) + if (!WARN_ON_ONCE(!irq_chip->irq_unmask)) irq_chip->irq_unmask(d); } for (; irq_counter[gpio] < fiq_count; irq_counter[gpio]++) From a304f483b6b00d42bde41c45ca52c670945348e2 Mon Sep 17 00:00:00 2001 From: Suman Anna Date: Tue, 25 Jun 2019 18:33:15 -0500 Subject: [PATCH 11/15] bus: ti-sysc: Simplify cleanup upon failures in sysc_probe() The clocks are not yet parsed and prepared until after a successful sysc_get_clocks(), so there is no need to unprepare the clocks upon any failure of any of the prior functions in sysc_probe(). The current code path would have been a no-op because of the clock validity checks within sysc_unprepare(), but let's just simplify the cleanup path by returning the error directly. While at this, also fix the cleanup path for a sysc_init_resets() failure which is executed after the clocks are prepared. Signed-off-by: Suman Anna Signed-off-by: Tony Lindgren --- drivers/bus/ti-sysc.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c index a319e1a748fe..2db474ab4c6b 100644 --- a/drivers/bus/ti-sysc.c +++ b/drivers/bus/ti-sysc.c @@ -2383,27 +2383,27 @@ static int sysc_probe(struct platform_device *pdev) error = sysc_init_dts_quirks(ddata); if (error) - goto unprepare; + return error; error = sysc_map_and_check_registers(ddata); if (error) - goto unprepare; + return error; error = sysc_init_sysc_mask(ddata); if (error) - goto unprepare; + return error; error = sysc_init_idlemodes(ddata); if (error) - goto unprepare; + return error; error = sysc_init_syss_mask(ddata); if (error) - goto unprepare; + return error; error = sysc_init_pdata(ddata); if (error) - goto unprepare; + return error; sysc_init_early_quirks(ddata); @@ -2413,7 +2413,7 @@ static int sysc_probe(struct platform_device *pdev) error = sysc_init_resets(ddata); if (error) - return error; + goto unprepare; error = sysc_init_module(ddata); if (error) From 5b63fb90adb95a178ad403e1703f59bf1ff2c16b Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 23 Jul 2019 00:29:23 -0700 Subject: [PATCH 12/15] ARM: dts: Fix incomplete dts data for am3 and am4 mmc Commit 4e27f752ab8c ("ARM: OMAP2+: Drop mmc platform data for am330x and am43xx") dropped legacy mmc platform data for am3 and am4, but missed the fact that we never updated the dts files for mmc3 that is directly on l3 interconnect instead of l4 interconnect. This leads to a situation with no legacy platform data and incomplete dts data. Let's update the mmc instances on l3 interconnect to probe properly with ti-sysc interconnect target module driver to make mmc3 work again. Let's still keep legacy "ti,hwmods" property around for v5.2 kernel and only drop it later on. Note that there is no need to use property status = "disabled" for mmc3. The default for dts is enabled, and runtime PM will idle unused instances just fine. Fixes: 4e27f752ab8c ("ARM: OMAP2+: Drop mmc platform data for am330x and am43xx") Reported-by: David Lechner Tested-by: David Lechner Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am33xx.dtsi | 32 ++++++++++++++++++++++++++------ arch/arm/boot/dts/am4372.dtsi | 32 ++++++++++++++++++++++++++------ 2 files changed, 52 insertions(+), 12 deletions(-) diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index e5c2f71a7c77..fb6b8aa12cc5 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -234,13 +234,33 @@ interrupt-names = "edma3_tcerrint"; }; - mmc3: mmc@47810000 { - compatible = "ti,omap4-hsmmc"; + target-module@47810000 { + compatible = "ti,sysc-omap2", "ti,sysc"; ti,hwmods = "mmc3"; - ti,needs-special-reset; - interrupts = <29>; - reg = <0x47810000 0x1000>; - status = "disabled"; + reg = <0x478102fc 0x4>, + <0x47810110 0x4>, + <0x47810114 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | + SYSC_OMAP2_ENAWAKEUP | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,sysc-sidle = , + , + ; + ti,syss-mask = <1>; + clocks = <&l3s_clkctrl AM3_L3S_MMC3_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x47810000 0x1000>; + + mmc3: mmc@0 { + compatible = "ti,omap4-hsmmc"; + ti,needs-special-reset; + interrupts = <29>; + reg = <0x0 0x1000>; + }; }; usb: usb@47400000 { diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index 55aff4db9c7c..848e2a8884e2 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -228,13 +228,33 @@ interrupt-names = "edma3_tcerrint"; }; - mmc3: mmc@47810000 { - compatible = "ti,omap4-hsmmc"; - reg = <0x47810000 0x1000>; + target-module@47810000 { + compatible = "ti,sysc-omap2", "ti,sysc"; ti,hwmods = "mmc3"; - ti,needs-special-reset; - interrupts = ; - status = "disabled"; + reg = <0x478102fc 0x4>, + <0x47810110 0x4>, + <0x47810114 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | + SYSC_OMAP2_ENAWAKEUP | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,sysc-sidle = , + , + ; + ti,syss-mask = <1>; + clocks = <&l3s_clkctrl AM4_L3S_MMC3_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x47810000 0x1000>; + + mmc3: mmc@0 { + compatible = "ti,omap4-hsmmc"; + ti,needs-special-reset; + interrupts = ; + reg = <0x0 0x1000>; + }; }; sham: sham@53100000 { From 0c0d1ec21b2f6070e22b54b2de874f1af960ced8 Mon Sep 17 00:00:00 2001 From: "Gustavo A. R. Silva" Date: Sun, 28 Jul 2019 18:22:40 -0500 Subject: [PATCH 13/15] ARM: OMAP: dma: Mark expected switch fall-throughs Mark switch cases where we are expecting to fall through. This patch fixes the following warnings: arch/arm/plat-omap/dma.c: In function 'omap_set_dma_src_burst_mode': arch/arm/plat-omap/dma.c:384:6: warning: this statement may fall through [-Wimplicit-fallthrough=] if (dma_omap2plus()) { ^ arch/arm/plat-omap/dma.c:393:2: note: here case OMAP_DMA_DATA_BURST_16: ^~~~ arch/arm/plat-omap/dma.c:394:6: warning: this statement may fall through [-Wimplicit-fallthrough=] if (dma_omap2plus()) { ^ arch/arm/plat-omap/dma.c:402:2: note: here default: ^~~~~~~ arch/arm/plat-omap/dma.c: In function 'omap_set_dma_dest_burst_mode': arch/arm/plat-omap/dma.c:473:6: warning: this statement may fall through [-Wimplicit-fallthrough=] if (dma_omap2plus()) { ^ arch/arm/plat-omap/dma.c:481:2: note: here default: ^~~~~~~ Notice that, in this particular case, the code comment is modified in accordance with what GCC is expecting to find. Reported-by: Stephen Rothwell Signed-off-by: Gustavo A. R. Silva Reviewed-by: Kees Cook Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/dma.c | 14 +++++--------- 1 file changed, 5 insertions(+), 9 deletions(-) diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index 79f43acf9acb..08c99413d02c 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -388,17 +388,15 @@ void omap_set_dma_src_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) /* * not supported by current hardware on OMAP1 * w |= (0x03 << 7); - * fall through */ + /* fall through */ case OMAP_DMA_DATA_BURST_16: if (dma_omap2plus()) { burst = 0x3; break; } - /* - * OMAP1 don't support burst 16 - * fall through - */ + /* OMAP1 don't support burst 16 */ + /* fall through */ default: BUG(); } @@ -474,10 +472,8 @@ void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) burst = 0x3; break; } - /* - * OMAP1 don't support burst 16 - * fall through - */ + /* OMAP1 don't support burst 16 */ + /* fall through */ default: printk(KERN_ERR "Invalid DMA burst mode\n"); BUG(); From d8e0cecbcaf09f38661bfb7da4c1e62297308672 Mon Sep 17 00:00:00 2001 From: Keerthy Date: Wed, 26 Jun 2019 13:20:14 +0530 Subject: [PATCH 14/15] soc: ti: pm33xx: Fix static checker warnings The patch fixes a bunch of static checker warnings. Reported-by: Dan Carpenter Signed-off-by: Keerthy Signed-off-by: Tony Lindgren --- drivers/soc/ti/pm33xx.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-) diff --git a/drivers/soc/ti/pm33xx.c b/drivers/soc/ti/pm33xx.c index bb77c220b6f8..5f3a4499cf40 100644 --- a/drivers/soc/ti/pm33xx.c +++ b/drivers/soc/ti/pm33xx.c @@ -252,7 +252,7 @@ static int am33xx_pm_begin(suspend_state_t state) if (state == PM_SUSPEND_MEM && pm_ops->check_off_mode_enable()) { nvmem = devm_nvmem_device_get(&omap_rtc->dev, "omap_rtc_scratch0"); - if (nvmem) + if (!IS_ERR(nvmem)) nvmem_device_write(nvmem, RTC_SCRATCH_MAGIC_REG * 4, 4, (void *)&rtc_magic_val); rtc_only_idle = 1; @@ -278,9 +278,12 @@ static void am33xx_pm_end(void) struct nvmem_device *nvmem; nvmem = devm_nvmem_device_get(&omap_rtc->dev, "omap_rtc_scratch0"); + if (IS_ERR(nvmem)) + return; + m3_ipc->ops->finish_low_power(m3_ipc); if (rtc_only_idle) { - if (retrigger_irq) + if (retrigger_irq) { /* * 32 bits of Interrupt Set-Pending correspond to 32 * 32 interrupts. Compute the bit offset of the @@ -291,8 +294,10 @@ static void am33xx_pm_end(void) writel_relaxed(1 << (retrigger_irq & 31), gic_dist_base + GIC_INT_SET_PENDING_BASE + retrigger_irq / 32 * 4); - nvmem_device_write(nvmem, RTC_SCRATCH_MAGIC_REG * 4, 4, - (void *)&val); + } + + nvmem_device_write(nvmem, RTC_SCRATCH_MAGIC_REG * 4, 4, + (void *)&val); } rtc_only_idle = 0; @@ -415,7 +420,7 @@ static int am33xx_pm_rtc_setup(void) nvmem = devm_nvmem_device_get(&omap_rtc->dev, "omap_rtc_scratch0"); - if (nvmem) { + if (!IS_ERR(nvmem)) { nvmem_device_read(nvmem, RTC_SCRATCH_MAGIC_REG * 4, 4, (void *)&rtc_magic_val); if ((rtc_magic_val & 0xffff) != RTC_REG_BOOT_MAGIC) From 4a65bbb9109ed7edd4b6ed7168ced48abb8561a2 Mon Sep 17 00:00:00 2001 From: YueHaibing Date: Sat, 13 Apr 2019 22:12:43 +0800 Subject: [PATCH 15/15] soc: ti: pm33xx: Make two symbols static Fix sparse warnings: drivers/soc/ti/pm33xx.c:144:27: warning: symbol 'rtc_wake_src' was not declared. Should it be static? drivers/soc/ti/pm33xx.c:160:5: warning: symbol 'am33xx_rtc_only_idle' was not declared. Should it be static? Signed-off-by: YueHaibing Signed-off-by: Tony Lindgren --- drivers/soc/ti/pm33xx.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/soc/ti/pm33xx.c b/drivers/soc/ti/pm33xx.c index 5f3a4499cf40..ccc6d53fe788 100644 --- a/drivers/soc/ti/pm33xx.c +++ b/drivers/soc/ti/pm33xx.c @@ -141,7 +141,7 @@ static int __init am43xx_map_gic(void) } #ifdef CONFIG_SUSPEND -struct wkup_m3_wakeup_src rtc_wake_src(void) +static struct wkup_m3_wakeup_src rtc_wake_src(void) { u32 i; @@ -157,7 +157,7 @@ struct wkup_m3_wakeup_src rtc_wake_src(void) return rtc_ext_wakeup; } -int am33xx_rtc_only_idle(unsigned long wfi_flags) +static int am33xx_rtc_only_idle(unsigned long wfi_flags) { omap_rtc_power_off_program(&omap_rtc->dev); am33xx_do_wfi_sram(wfi_flags);