Take the mutex early in the resume handler and use the locked version of
the IRQ routine. This ensures any recoveries queued will only take place
after resume has fully completed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate the threaded IRQ handling routine into two functions.
The outer function takes the mutex and calls recovery on errors. It also
performs a Tx-path optimization to avoid redundant works.
The inner function is simplified - all calls to recovery are removed and
it assumes the lock is taken. The locked variant will be reused elsewhere.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Propagate some missing return values for Rx-filter related functions.
This and makes sure we always fail the suspend in case of SDIO errors.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If an error is detected after mac80211 is already suspended, the recovery
work will not be queued. This will leave the driver in a bad state on
resume.
Detect this in the resume op and re-queue a recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set a flag and after the first read/write failure is encountered.
This flag will disallow further SDIO read/writes until op_stop() is
executed, which will clear all flags.
This prevents further errors from occurring, since one error usually
indicates that IO operations won't work anymore until the chip is
rebooted. By blocking more calls, we avoid extra timeouts and having
to wait for them to occur.
[Added second paragraph explaining why the change is needed. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
usb: fixes for v3.5-rc3
A few remaining fixes for our v3.5 cycle containing a fix
for a long standing bug which would cause musb to starve its
dma channels by never releasing them, a build fix on lpc32xx_udc,
another fix to Ido's endpoint descriptor series on fsl udc, a
fix to the order of arguments on twl6030-usb driver and a
fix to dwc3's dequeue method.
All patches have been pending on the list for quite a while.
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly. They
report bogus sizes, in some cases becoming unusable as a result.
The bugs were triggered by commit
09b6b51b0b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices. By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.
It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly. Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.
Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device. If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.
This fixes Bugzilla #43391.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commit couldn't work if the RMCR is not set to 1.
"net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens"
commit id 79fba9f517
If RMCR is not set, the controller will clear the EDRRR after it received
a frame. In this case, the driver doesn't need to fix the value of
cur_rx/dirty_rx. The driver only needs it when the controll detects
receive descriptors are empty.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8168evl (RTL_GIGA_MAC_VER_34) based Gigabyte GA-990FXA motherboards
are very prone to NETDEV watchdog problems without this change. See
https://bugzilla.kernel.org/show_bug.cgi?id=42899 for instance.
I don't know why it *works*. It's depressingly effective though.
For the record:
- the problem may go along IOMMU (AMD-Vi) errors but it really looks
like a red herring.
- the patch sets the RX_MULTI_EN bit. If the 8168c doc is any guide,
the chipset now fetches several Rx descriptors at a time.
- long ago the driver ignored the RX_MULTI_EN bit.
e542a2269f changed the RxConfig
settings. Whatever the problem it's now labeled a regression.
- Realtek's own driver can identify two different 8168evl devices
(CFG_METHOD_16 and CFG_METHOD_17) where the r8169 driver only
sees one. It sucks.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Ceph fixes from Sage Weil:
"There are a couple of fixes from Yan for bad pointer dereferences in
the messenger code and when fiddling with page->private after page
migration, a fix from Alex for a use-after-free in the osd client
code, and a couple fixes for the message refcounting and shutdown
ordering."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: flush msgr queue during mon_client shutdown
rbd: Clear ceph_msg->bio_iter for retransmitted message
libceph: use con get/put ops from osd_client
libceph: osd_client: don't drop reply reference too early
ceph: check PG_Private flag before accessing page->private
If usbnet is resumed by remote wakeup, generally there are
some packets comming to be handled, so allocate and submit
rx URBs in usbnet_resume to avoid delays introduced by tasklet.
Otherwise, usbnet may have been runtime suspended before the
usbnet_bh is executed to schedule Rx URBs.
Without the patch, usbnet can't recieve any packets from peer
in runtime suspend state if runtime PM is enabled and
autosuspend_delay is set as zero.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch decreases dev->suspend_count in the -EBUSY failure path
of usbnet_suspend. Without the change, the later runtime suspend
will do nothing except for increasing dev->suspend_count.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without clearing OPEN flag in failure path, runtime or system resume
may submit interrupt/rx URB and start tx queue mistakenly on a
interface in DOWN state.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does several things:
1. Add static to function when possible.
2. Correct comments.
3. Change msleep(small) --> usleep_range(small, small*2).
Also correct existing calls to usleep_range.
4. Remove dead code.
5. Change 'if(rc != 0)' --> if(rc)
Most of these changes are purely semantic.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the ability to identify sfp+ modules' Tx fault, and when such
occur shut down the link.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignoring interfaces with additional descriptors is not a reliable
method for locating the correct interface on Gobi devices. There
is at least one device where this method fails:
https://bbs.archlinux.org/viewtopic.php?id=143506
The result is that the AT command port (interface #2) is hidden
from qcserial, preventing traditional serial modem usage:
[ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device
[ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22
[ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device
[ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22
[ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected
[ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0
[ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected
[ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1
Use static interface numbers taken from the interface map in
qcserial for all Gobi devices instead:
Gobi 1K USB layout:
0: serial port (doesn't respond)
1: serial port (doesn't respond)
2: AT-capable modem port
3: QMI/net
Gobi 2K+ USB layout:
0: QMI/net
1: DM/DIAG (use libqcdm from ModemManager for communication)
2: AT-capable modem port
3: NMEA
This should be more reliable over all, and will also prevent the
noisy "probe failed" messages. The whitelisting logic is expected
to be replaced by direct interface number matching in 3.6.
Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de>
Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic
Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes compilation with NF_CONNTRACK_EVENTS=n and
NETFILTER_NETLINK_QUEUE_CT=y.
I'm leaving all those static inline functions that calculate the size
of the event message out of the ifdef area of NF_CONNTRACK_EVENTS since
they will not be included by gcc in case they are unused.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This change is meant to add a control for disabling early socket demux.
The main motivation behind this patch is to provide an option to disable
the feature as it adds an additional cost to routing that reduces overall
throughput by up to 5%. For example one of my systems went from 12.1Mpps
to 11.6 after the early socket demux was added. It looks like the reason
for the regression is that we are now having to perform two lookups, first
the one for an established socket, and then the one for the routing table.
By adding this patch and toggling the value for ip_early_demux to 0 I am
able to get back to the 12.1Mpps I was previously seeing.
[ Move local variables in ip_rcv_finish() down into the basic
block in which they are actually used. -DaveM ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We encapsulate enbale irq functionality in a function call.
As on probe the interrupts will be disabled twice, we delete
one.
Signed-off-by: Matthias Brugger <mbrugger@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, the interrupts for I2C, VIN, GPIO, SDHC, HSCIF and
HPB-DMAC are sent to the SH processor.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch fixes the problem on some HP desktop machines with eDP
which give blank screens after S3 resume.
It turned out that BLC_PWM_CPU_CTL must be written after
BLC_PWM_CPU_CTL2. Otherwise it doesn't take effect on these
SNB machines.
Tested with 3.5-rc3 kernel.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49233
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After banging my head against this for the past few months, I still
don't see how this could possible race under the premise that once an
irq bit is masked in PM_IMR and reset in PM_IIR it won't show up again
until we unmask it in PM_IMR.
Still, we have reports of this being seen in the wild. Now Bspec has
this little bit of lovely language in the PMIIR register:
Public SNB Docs, Vol3Part2, 2.5.14 "PMIIR":
"For each bit, the IIR can store a second pending interrupt if two or
more of the same interrupt conditions occur before the first condition
is cleared. Upon clearing the interrupt, the IIR bit will momentarily
go low, then return high to indicate there is another interrupt
pending."
Now if we presume that PMIMR only prevent new interrupts from being
queued, we could easily end up masking an interrupt and clearing it,
but the 2nd pending interrupt setting the bit in PMIIR right away
again. Which leads, the next time the irq handler runs, to hitting the
WARN.
Also, no bad side effects of this have ever been reported. And we've
tracked down our issues with the gpu turbo getting stuck to bogus
interrupt generation limits in th RPLIMIT register.
So let's just rip out this WARN as bogus and call it a day. The only
shallow thing here is that this 2-deep irq queue in the hw makes you
wonder how racy the windows irq handler is ...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42907
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ARM builds seem to be plagued by an occasional build error:
Inconsistent kallsyms data
This is a bug - please report about it
Try "make KALLSYMS_EXTRA_PASS=1" as a workaround
The problem has to do with alignment of some sections by the linker.
The kallsyms data is built in two passes by first linking the kernel
without it, and then linking the kernel again with the symbols
included. Normally, this just shifts the symbols, without changing
their order, and the compression used by the kallsyms gives the same
result.
On non SMP, the per CPU data is empty. Depending on the where the
alignment ends up, it can come out as either:
+-------------------+
| last text segment |
+-------------------+
/* padding */
+-------------------+ <- L1_CACHE_BYTES alignemnt
| per cpu (empty) |
+-------------------+
__per_cpu_end:
/* padding */
__data_loc:
+-------------------+ <- THREAD_SIZE alignment
| data |
+-------------------+
or
+-------------------+
| last text segment |
+-------------------+
/* padding */
+-------------------+ <- L1_CACHE_BYTES alignemnt
| per cpu (empty) |
+-------------------+
__per_cpu_end:
/* no padding */
__data_loc:
+-------------------+ <- THREAD_SIZE alignment
| data |
+-------------------+
if the alignment satisfies both. Because symbols that have the same
address are sorted by 'nm -n', the second case will be in a different
order than the first case. This changes the compression, changing the
size of the kallsym data, causing the build failure.
The KALLSYMS_EXTRA_PASS=1 workaround usually works, but it is still
possible to have the alignment change between the second and third
pass. It's probably even possible for it to never reach a fixedpoint.
The problem only occurs on non-SMP, when the per-cpu data is empty,
and when the data segment has alignment (and immediately follows the
text segments). Fix this by only including the per_cpu section on
SMP, when it is not empty.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We wish to postpone suspend if recovery is pending. This will make sure
the FW is in a good state and perform wowlan wakeup.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Applications running in the user space needs access to the
memory of the chip. Examples of such access
- read/write global variables
- access to firmware log
- dump memory after firmware panic event
Arbitrary 4-bytes aligned location can be accessed by
read/write file wlcore/mem
[Check return value of wlcore_raw_read/write and wlcore_set_partition
calls as required by the recent IO changes. -- Luca]
Signed-off-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When running in AP mode, the driver reports all deletions from CAM in
a cryptic manner that makes users think it is an error. change so that
the condition is only reported at higher-levels of debugging.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename mrcCCKOff for better code readability and also fixes
the smatch warning.
drivers/net/wireless/ath/ath9k/ar9003_phy.c:982
ar9003_hw_ani_control() Error invalid range 1 to 0.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the function brcms_c_regd_init() the channels are validated
against the device capabilities. This is done for both 2.4G and
5G band, but there are devices that are 2.4G only, ie. BCM4313.
For that device this leads to a NULL dereference. This patch adds
a check in brcms_c_regd_init() to fix this.
Issue introduced in wireless-next tree by following commit:
cf03c5d brcm80211: smac: inform mac80211 of the X2 regulatory domain
Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes problem detected in linux-next build for powerpc
allyesconfig. The error message below is no longer observed:
CC drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c: In function 'brcmf_sdio_dump_console':
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: error: implicit declaration of function 'vzalloc'
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: warning: assignment makes pointer from integer without a cast
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3113: error: implicit declaration of function 'vfree'
make[2]: *** [drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o] Error 1
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FW will not explicitly notify about host sleep activation to the
host for USB and PCIe chipsets. Hence host should generate Host
Sleep Activated event as soon as Host Sleep parameters are
configured to FW successfully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a flaw in recently implemented logic to handle Tx traffic
and scan operation simultaneously. We missed to wakeup main thread
to handle Tx traffic if scan is delayed/aborted.
For some cards (SD8797, for example), firmware will send SLEEP event
if there is no activity for 50msec. While handling the SLEEP event,
main thread will be woken up and Tx packet gets sent hence. In worst
case Tx traffic will be delayed for 50msec.
For other cards, such as USB8797, firmware won't send SLEEP event.
So, Tx traffic gets stuck if no other event triggers the wakeup of
main thread.
This patch fixes above issues.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for parsing WPA IE from beacon parameter of
cfg80211_ap_settings and set it to FW.
WPA/WPA2 mixed mode is supported with this patch.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull XFS fixes from Ben Myers:
- Fix stale data exposure with unwritten extents
- Fix a warning in xfs_alloc_vextent with ODEBUG
- Fix overallocation and alignment of pages for xfs_bufs
- Fix a cursor leak
- Fix a log hang
- Fix a crash related to xfs_sync_worker
- Rename xfs log structure from struct log to struct xlog so we can use
crash dumps effectively
* tag 'for-linus-Jun-21-2012' of git://oss.sgi.com/xfs/xfs:
xfs: rename log structure to xlog
xfs: shutdown xfs_sync_worker before the log
xfs: Fix overallocation in xfs_buf_allocate_memory()
xfs: fix allocbt cursor leak in xfs_alloc_ag_vextent_near
xfs: check for stale inode before acquiring iflock on push
xfs: fix debug_object WARN at xfs_alloc_vextent()
xfs: xfs_vm_writepage clear iomap_valid when !buffer_uptodate (REV2)
skb allocated during initialisation is reused for receiving
commands/events by USB interface. We miss to reset skb->data in
failure cases. This patch takes care of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures uniformity in event skb sent by interface code
(USB/PCIe/SDIO) which automatically fixes following bugs.
1) For USB interface, same buffer is reused for receiving cmd and
events from firmware. While handling events, we perform
skb_pull(skb, 4) to remove event header. Corresponding skb_push()
call is missing while submitting the buffer.
2) For PCIe interface, event skb is passed with event header.
Recently added uAP events EVENT_UAP_STA_ASSOC, EVENT_UAP_STA_DEAUTH
will not work for PCIe, as they assume event skb points to event body.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After association, STA will go through eapol handshake with WPS
enabled AP. It's observed that WPS handshake fails with some 11n
AP. The reason for the failure is that the eapol packet is sent
via 11n frame aggregation.
The eapol packet should be sent directly without 11n aggregation.
This patch fixes the problem by adding WPS session control while
dequeuing Tx packets for transmission.
Cc: "3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we check the sequence number of last packet received
against start_win. If a sequence hole is detected, start_win is
updated to next sequence number.
Since the rx sequence number is initialized to 0, a corner case
exists when BA setup happens immediately after association. As
0 is a valid sequence number, start_win gets increased to 1
incorrectly. This causes the first packet with sequence number 0
being dropped.
Initialize rx sequence number as 0xffff and skip adjusting
start_win if the sequence number remains 0xffff. The sequence
number will be updated once the first packet is received.
Cc: "3.0.y, 3.1.y, 3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
