A couple of drivers have leftovers from netdev ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN911x datasheet specifies a minimum delay of 45ns between a write
of E2P_DATA and any read. This patch adds a single dummy read of
BYTE_TEST to enforce this timing constraint.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that was added to increase headroom was wrong.
It doesn't handle the case where gfar_add_fcb() changes the skb.
Better to do check at start of transmit (outside of lock), where
error handling is better anyway.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The benet driver is doing a 64 bit divide, which is not supported in
Linux kernel on 32 bit architectures. The correct way to do this is to
use do_div(). Compile tested on i386 only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a platform device driver that supports the OpenCores 10/100
Mbps Ethernet MAC.
The driver expects three resources: one IORESOURCE_MEM resource defines the
memory region for the core's memory-mapped registers while a second
IORESOURCE_MEM resource defines the network packet buffer space. The third
resource, of type IORESOURCE_IRQ, associates an interrupt with the driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When net-next and infiniband were merged upstream, each branch deleted
one of a pair of adjacent lines from nes_nic.c, but when Linus fixed the
conflict up, he brought back both of the lines. Fix up to the intended
final tree state.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: irq_node.handler() should return irqreturn_t
m68k: section mismatch fixes: Atari SCSI
m68k: section mismatch fixes: DMAsound for Atari
MAINTAINERS: Replace dead link to m68k CVS repository by link to new git repository
m68k: mac - Add SWIM floppy support
m68k: mac - Add a new entry in mac_model to identify the floppy controller type.
m68k: Add install target
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: disable __do_IRQ support
sparseirq, powerpc/cell: fix unused variable warning in interrupt.c
genirq: deprecate obsolete typedefs and defines
genirq: deprecate __do_IRQ
genirq: add doc to struct irqaction
genirq: use kzalloc instead of explicit zero initialization
genirq: make irqreturn_t an enum
genirq: remove redundant if condition
genirq: remove unused hw_irq_controller typedef
irq: export remove_irq() and setup_irq() symbols
irq: match remove_irq() args with setup_irq()
irq: add remove_irq() for freeing of setup_irq() irqs
genirq: assert that irq handlers are indeed running in hardirq context
irq: name 'p' variables a bit better
irq: further clean up the free_irq() code flow
irq: refactor and clean up the free_irq() code flow
irq: clean up manage.c
irq: use GFP_KERNEL for action allocation in request_irq()
kernel/irq: fix sparse warning: make symbol static
irq: optimize init_kstat_irqs/init_copy_kstat_irqs
...
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (81 commits)
[S390] remove duplicated #includes
[S390] cpumask: use mm_cpumask() wrapper
[S390] cpumask: Use accessors code.
[S390] cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.
[S390] cpumask: remove cpu_coregroup_map
[S390] fix clock comparator save area usage
[S390] Add hwcap flag for the etf3 enhancement facility
[S390] Ensure that ipl panic notifier is called late.
[S390] fix dfp elf hwcap/facility bit detection
[S390] smp: perform initial cpu reset before starting a cpu
[S390] smp: fix memory leak on __cpu_up
[S390] ipl: Improve checking logic and remove switch defaults.
[S390] s390dbf: Remove needless check for NULL pointer.
[S390] s390dbf: Remove redundant initilizations.
[S390] use kzfree()
[S390] BUG to BUG_ON changes
[S390] zfcpdump: Prevent zcore from beeing built as a kernel module.
[S390] Use csum_partial in checksum.h
[S390] cleanup lowcore.h
[S390] eliminate ipl_device from lowcore
...
* 'for-2.6.30' of git://git.kernel.dk/linux-2.6-block:
Get rid of pdflush_operation() in emergency sync and remount
btrfs: get rid of current_is_pdflush() in btrfs_btree_balance_dirty
Move the default_backing_dev_info out of readahead.c and into backing-dev.c
block: Repeated lines in switching-sched.txt
bsg: Remove bogus check against request_queue->max_sectors
block: WARN in __blk_put_request() for potential bio leak
loop: fix circular locking in loop_clr_fd()
loop: support barrier writes
bsg: add support for tail queuing
cpqarray: enable bus mastering
block: genhd.h cleanup patch
block: add private bio_set for bio integrity allocations
block: genhd.h comment needs updating
block: get rid of unused blkdev_free_rq() define
block: remove various blk_queue_*() setting functions in blk_init_queue_node()
cciss: add BUILD_BUG_ON() for catching bad CommandList_struct alignment
block: don't create bio_vec slabs of less than the inline number
block: cleanup bio_alloc_bioset()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
RDMA/cxgb3: Enforce required firmware
IB/mlx4: Unregister IB device prior to CLOSE PORT command
mlx4_core: Add link type autosensing
mlx4_core: Don't perform SET_PORT command for Ethernet ports
RDMA/nes: Handle MPA Reject message properly
RDMA/nes: Improve use of PBLs
RDMA/nes: Remove LLTX
RDMA/nes: Inform hardware that asynchronous event has been handled
RDMA/nes: Fix tmp_addr compilation warning
RDMA/nes: Report correct vendor_id and vendor_part_id
RDMA/nes: Update copyright to new legal entity and year
RDMA/nes: Account for freed PBL after HW operation
IB: Remove useless ibdev_is_alive() tests from sysfs code
IB/sa_query: Fix AH leak due to update_sm_ah() race
IB/mad: Fix ib_post_send_mad() returning 0 with no generate send comp
IB/mad: initialize mad_agent_priv before putting on lists
IB/mad: Fix null pointer dereference in local_completions()
IB/mad: Fix RMPP header RRespTime manipulation
IB/iser: Remove hard setting of path MTU
mlx4_core: Add device IDs for MT25458 10GigE devices
...
It allows to read data from a floppy, but not to write to, and to eject the
floppy (useful on our Mac without eject button).
Signed-off-by: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (35 commits)
[libata] Improve timeout handling
[libata] Drain data on errors
pata_sc1200: Activate secondary channel
pata_artop: Serializing support
[libata] ahci: correct enclosure LED state save
[libata] More robust parsing for IDENTIFY DEVICE multi_count field
sata_mv: fix LED blinking for SoC+NCQ
sata_mv: optimize IRQ coalescing for 8-port chips
sata_mv: implement IRQ coalescing (v2)
sata_mv: cosmetic preparations for IRQ coalescing
pata-rb532-cf: platform_get_irq() fix ignored failure
pata_efar: fix *dma_mask
pata_radisys: fix mwdma_mask to exclude mwdma0
[libata] convert drivers to use ata.h mode mask defines
include/linux/ata.h: add some more transfer masks
ahci: Blacklist HP Compaq 6720s that spins off disks during ACPI power off
[libata] sata_mv: Implement direct FIS transmission via mv_qc_issue_fis().
[libata] Export ata_pio_queue_task() so that it can be used from sata_mv.
[libata] sata_mv: Add a new mv_sff_check_status() function to sata_mv.
[libata] sata_mv: Tighten up interrupt masking in mv_qc_issue()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (97 commits)
USB: qcserial: add device id for HP devices
USB: isp1760: Add a delay before reading the SKIPMAP registers in isp1760-hcd.c
USB: allow malformed LANGID descriptors
USB: pxa27x_udc: typo fixes and code cleanups
USB: gadget: gadget zero uses new suspend/resume hooks
USB: gadget: composite device-level suspend/resume hooks
USB: r8a66597-hcd: suspend/resume support
USB: more u32 conversion after transfer_buffer_length and actual_length
USB: Fix cp2101 USB serial device driver termios functions for console use
USB: CP2101 New Device ID
USB: ipaq: handle 4 endpoint devices
USB: S3C: Move usb-control.h to platform include
USB: ohci-hcd: Add ARCH_S3C24XX to the ohci-s3c2410.c glue
USB: pedantic: spelling correction in comment for ch9.h
USB: host: fix sparse warning: Using plain integer as NULL pointer
USB: ohci-s3c2410: fix name of bus clock
USB: ohci-s3c2410: remove <mach/hardware.h> include
USB: serial: rename cp2101 driver to cp210x
USB: CP2101 Reduce Error Logging
USB: CP2101 Support AN205 baud rates
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (53 commits)
ide: use try_to_identify() in ide_driveid_update()
ide: clear drive IRQ after re-enabling local IRQs in ide_driveid_update()
ide: sanitize SELECT_MASK() usage in ide_driveid_update()
ide: classify device type in do_probe()
ide: remove broken EXABYTENEST support
ide: shorten timeout value in ide_driveid_update()
ide: propagate AltStatus workarounds to ide_driveid_update()
ide: fix kmalloc() failure handling in ide_driveid_update()
mn10300: remove <asm/ide.h>
frv: remove <asm/ide.h>
ide: remove pciirq argument from ide_pci_setup_ports()
ide: fix ->init_chipset method to return 'int' value
ide: remove try_to_identify() wrapper
ide: remove no longer needed IRQ auto-probing from try_to_identify() (v2)
ide: remove no longer needed IRQ fallback code from hwif_init()
amd74xx: remove no longer needed ->init_hwif method
ide: remove no longer needed IDE_HFLAG[_FORCE]_LEGACY_IRQS
ide: use ide_pci_is_in_compatibility_mode() in ide_pci_init_{one,two}()
ide: use pci_get_legacy_ide_irq() in ide_pci_init_{one,two}()
ide: handle IDE_HFLAG[_FORCE]_LEGACY_IRQS in ide_pci_init_{one,two}()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (96 commits)
sh: add support for SMSC Polaris platform
sh: fix the HD64461 level-triggered interrupts handling
sh: sh-rtc wakeup support
sh: sh-rtc invalid time rework
sh: sh-rtc carry interrupt rework
sh: disallow kexec virtual entry
sh: kexec jump: fix for ftrace.
sh: kexec: Drop SR.BL bit toggling.
sh: add kexec jump support
sh: rework kexec segment code
sh: simplify kexec vbr code
sh: Flush only the needed range when unmapping a VMA.
sh: Update debugfs ASID dumping for 16-bit ASID support.
sh: tlb-pteaex: Kill off legacy PTEA updates.
sh: Support for extended ASIDs on PTEAEX-capable SH-X3 cores.
sh: sh7763rdp: Change IRQ number for sh_eth of sh7763rdp
sh: espt-giga board support
sh: dma: Make G2 DMA configurable.
sh: dma: Make PVR2 DMA configurable.
sh: Move IRQ multi definition of DMAC to defconfig
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (430 commits)
ALSA: hda - Add quirk for Acer Ferrari 5000
ALSA: hda - Use cached calls to get widget caps and pin caps
ALSA: hda - Don't create empty/single-item input source
ALSA: hda - Fix the wrong pin-cap check in patch_realtek.c
ALSA: hda - Cache pin-cap values
ALSA: hda - Avoid output amp manipulation to digital mic pins
ALSA: hda - Add function id to proc output
ALSA: pcm - Safer boundary checks
ALSA: hda - Detect digital-mic inputs on ALC663 / ALC272
ALSA: sound/ali5451: typo: s/resouces/resources/
ALSA: hda - Don't show the current connection for power widgets
ALSA: Fix wrong pointer to dev_err() in arm/pxa2xx-ac97-lib.c
ASoC: Declare Headset as Mic and Headphone widgets for SDP3430
ASoC: OMAP: N810: Add more jack functions
ASoC: OMAP: N810: Mark not connected input pins
ASoC: Add FLL support for WM8400
ALSA: hda - Don't reset stream at each prepare callback
ALSA: hda - Don't reset BDL unnecessarily
ALSA: pcm - Fix delta calculation at boundary overlap
ALSA: pcm - Reset invalid position even without debug option
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (29 commits)
crypto: sha512-s390 - Add missing block size
hwrng: timeriomem - Breaks an allyesconfig build on s390:
nlattr: Fix build error with NET off
crypto: testmgr - add zlib test
crypto: zlib - New zlib crypto module, using pcomp
crypto: testmgr - Add support for the pcomp interface
crypto: compress - Add pcomp interface
netlink: Move netlink attribute parsing support to lib
crypto: Fix dead links
hwrng: timeriomem - New driver
crypto: chainiv - Use kcrypto_wq instead of keventd_wq
crypto: cryptd - Per-CPU thread implementation based on kcrypto_wq
crypto: api - Use dedicated workqueue for crypto subsystem
crypto: testmgr - Test skciphers with no IVs
crypto: aead - Avoid infinite loop when nivaead fails selftest
crypto: skcipher - Avoid infinite loop when cipher fails selftest
crypto: api - Fix crypto_alloc_tfm/create_create_tfm return convention
crypto: api - crypto_alg_mod_lookup either tested or untested
crypto: amcc - Add crypt4xx driver
crypto: ansi_cprng - Add maintainer
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (35 commits)
[CPUFREQ] Prevent p4-clockmod from auto-binding to the ondemand governor.
[CPUFREQ] Make cpufreq-nforce2 less obnoxious
[CPUFREQ] p4-clockmod reports wrong frequency.
[CPUFREQ] powernow-k8: Use a common exit path.
[CPUFREQ] Change link order of x86 cpufreq modules
[CPUFREQ] conservative: remove 10x from def_sampling_rate
[CPUFREQ] conservative: fixup governor to function more like ondemand logic
[CPUFREQ] conservative: fix dbs_cpufreq_notifier so freq is not locked
[CPUFREQ] conservative: amend author's email address
[CPUFREQ] Use swap() in longhaul.c
[CPUFREQ] checkpatch cleanups for acpi-cpufreq
[CPUFREQ] powernow-k8: Only print error message once, not per core.
[CPUFREQ] ondemand/conservative: sanitize sampling_rate restrictions
[CPUFREQ] ondemand/conservative: deprecate sampling_rate{min,max}
[CPUFREQ] powernow-k8: Always compile powernow-k8 driver with ACPI support
[CPUFREQ] Introduce /sys/devices/system/cpu/cpu*/cpufreq/cpuinfo_transition_latency
[CPUFREQ] checkpatch cleanups for powernow-k8
[CPUFREQ] checkpatch cleanups for ondemand governor.
[CPUFREQ] checkpatch cleanups for powernow-k7
[CPUFREQ] checkpatch cleanups for speedstep related drivers.
...
Use kzfree() instead of memset() + kfree().
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cksm function in system.h is duplicate to csum_partial in checksum.h.
Remove cksm and use csum_partial instead.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Trivial cleanup, list_del(); list_add{,_tail}() is equivalent
to list_move{,_tail}(). Semantic patch for coccinelle can be
found at www.cccmz.de/~snakebyte/list_move_tail.spatch
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is a cleanup of all the messages this driver prints. It uses the
dev_message macros now.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The inbound and outbound handlers are nearly identical if the outbound
handler uses first_to_check as end index instead of last_move. Since both
values are identical at that point the handlers can be merged.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Errors from SIGA instructions are stored in the per queue qdio_error
and reported back when the queue handler is called. That opens a race
when multiple error conditions occur simultanously.
Report SIGA errors immediately in the return value of do_QDIO so the
upper layer can react and SIGA errors no longer interfere with other
errors.
Move the SIGA error handling in qeth from the outbound handler to
qeth_flush_buffers.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
If the qdio module is unloaded the tiqdio tasklet must be terminated
by tasklet_kill. Move the tasklet_kill after the unregistration of
the adapter interrupt so the tiqdio tasklet will not be scheduled
anymore before calling tasklet_kill.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The index value that indicated that the input queue moved was also used to
store the index of the first acknowledged buffer. For non-qebsm only the
newest buffer is acknowledged which may be different from the last move index
so two seperate values are needed to track the input queue.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ACKnowledgement state should be set on the newest SBAL so an
adapter interrupt surpression check needs to scan fewer SBALs.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qdio_cleanup is a wrapper function that should call qdio_shutdown and
qdio_free. qdio_free was not called if an error occured in qdio_shutdown
resulting in a missing free of allocated resources.
Call qdio_free regardless of the return value of qdio_shutdown.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The queue tasklets were stopped with tasklet_disable. Although tasklet_disable
prevents the tasklet from beeing executed it is still possible that a tasklet
is scheduled on a CPU at that point. A following qdio_establish calls
tasklet_init which clears the tasklet count and the tasklet state leading to
the following Oops:
<2>kernel BUG at kernel/softirq.c:392!
<4>illegal operation: 0001 [#1] SMP
<4>Modules linked in: iptable_filter ip_tables x_tables dm_round_robin dm_multipath scsi_dh sg sd_mod crc_t10dif nfs lockd nfs
_acl sunrpc fuse loop dm_mod qeth_l3 ipv6 zfcp qeth scsi_transport_fc qdio scsi_tgt scsi_mod chsc_sch ccwgroup dasd_eckd_mod dasdm
od ext3 mbcache jbd
<4>Supported: Yes
<4>CPU: 0 Not tainted 2.6.27.13-1.1.mz13-default #1
<4>Process blast.LzS_64 (pid: 16445, task: 000000006cc02538, ksp: 000000006cb67998)
<4>Krnl PSW : 0704c00180000000 00000000001399f4 (tasklet_action+0xc8/0x1d4)
<4> R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 EA:3
<4>Krnl GPRS: ffffffff00000030 0000000000000002 0000000000000002 fffffffffffffffe
<4> 000000000013aabe 00000000003b6a18 fffffffffffffffd 0000000000000000
<4> 00000000006705a8 000000007d0914a8 000000007d0914b0 000000007fecfd30
<4> 0000000000000000 00000000003b63e8 000000007fecfd90 000000007fecfd30
<4>Krnl Code: 00000000001399e8: b9200021 cgr %r2,%r1
<4> 00000000001399ec: a7740004 brc 7,1399f4
<4> 00000000001399f0: a7f40001 brc 15,1399f2
<4> >00000000001399f4: c0100027e8ee larl %r1,636bd0
<4> 00000000001399fa: bf1f1008 icm %r1,15,8(%r1)
<4> 00000000001399fe: a7840019 brc 8,139a30
<4> 0000000000139a02: c0300027e8ef larl %r3,636be0
<4> 0000000000139a08: e3c030000004 lg %r12,0(%r3)
<4>Call Trace:
<4>([<0000000000139c12>] tasklet_hi_action+0x112/0x1d4)
<4> [<000000000013aabe>] __do_softirq+0xde/0x1c4
<4> [<000000000010fa2e>] do_softirq+0x96/0xb0
<4> [<000000000013a8d8>] irq_exit+0x70/0xcc
<4> [<000000000010d1d8>] do_extint+0xf0/0x110
<4> [<0000000000113b10>] ext_no_vtime+0x16/0x1a
<4> [<000003e0000a3662>] ext3_dirty_inode+0xe6/0xe8 [ext3]
<4>([<00000000001f6cf2>] __mark_inode_dirty+0x52/0x1d4)
<4> [<000003e0000a44f0>] ext3_ordered_write_end+0x138/0x190 [ext3]
<4> [<000000000018d5ec>] generic_perform_write+0x174/0x230
<4> [<0000000000190144>] generic_file_buffered_write+0xb4/0x194
<4> [<0000000000190864>] __generic_file_aio_write_nolock+0x418/0x454
<4> [<0000000000190ee2>] generic_file_aio_write+0x76/0xe4
<4> [<000003e0000a05c2>] ext3_file_write+0x3e/0xc8 [ext3]
<4> [<00000000001cc2fe>] do_sync_write+0xd6/0x120
<4> [<00000000001ccfc8>] vfs_write+0xac/0x184
<4> [<00000000001cd218>] SyS_write+0x68/0xe0
<4> [<0000000000113402>] sysc_noemu+0x10/0x16
<4> [<0000020000043188>] 0x20000043188
<4>Last Breaking-Event-Address:
<4> [<00000000001399f0>] tasklet_action+0xc4/0x1d4
<6>qdio: 0.0.c61b ZFCP on SC f67 using AI:1 QEBSM:0 PCI:1 TDD:1 SIGA: W AOP
<4> <0>Kernel panic - not syncing: Fatal exception in interrupt
Use tasklet_kill instead of tasklet_disbale. Since tasklet_schedule must not be
called after tasklet_kill use the QDIO_IRQ_STATE_STOPPED to inidicate that a
queue is going down and prevent further tasklet schedules in that case.
Remove superflous tasklet_schedule from input queue setup, at that time
the queues are not ready so the schedule results in a NOP.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the call to qdio_shutdown from qdio_activate since the upper-layer
drivers are responsible to call qdio_shutdown when qdio_activate returns
with an error.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a mutex to protect the tiq_list. Although reading the list is done
using RCU adding and removing elements from the list must still
happen locked since multiple qdio devices may change the list in parallel
otherwise.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Subchannel reprobing can block the kslowcrw workqueue indefinitely
while waiting for device recognition to finish which is also scheduled
to run on kslowcrw. Prevent this deadlock by moving the waiting
portion of subchannel reprobing to the cio workqueue.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove unused subchannel pointer in io_subchannel_recog_done.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix incorrect check for active I/O in interrogate function.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In some situations a rc in __chsc_do_secm will be overwritten
by another one. This shouldn't do harm since todays callers
don't check for _specific_ errors but fix it for the sake of
correctness.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Writing only spaces to /proc/cio_ignore will cause a buffer overflow
since the size_t value i will not become negative and so buf[-1UL] is
accessed. Change the value of i to ssize_t.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a ccw group device unbinding it from its driver should do the
same as a call to ungroup, since this virtual device can not exist
without a driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some sanity checks in the ccw group driver test the output of
container_of macros to be !NULL. Test the input parameters instead.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case the ccw group driver refuses to set a device [on|off]line,
we should transmit the return code to the caller.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
MAX_ISC is a valid isc number, so arrays with an index of isc
need to have a length of MAX_ISC+1
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since some callers rely on for_each_subchannel_staged to not fail,
fall back to brute force scanning using get_subchannel_by_schid in
case of a oom situation.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add barrier to prevent compiler from reloading pointer to irq handler.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The crw_unregister_handler uses xchg + synchronize_sched when
unregistering a crw_handler.
This doesn't protect crw_collect_info to potentially jump to NULL since
it has unlocked code like this:
if (crw_handlers[i])
crw_handlers[i](NULL, NULL, 1);
So add a mutex which protects the crw handler array for changes.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case the ccw driver refuses to set a device offline, we should
transmit the return code to the caller.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use ccw_device_set_notoper() (which also deletes the device
timer and disables the subchannel) instead of simply setting
the state to DEV_STATE_NOT_OPER in the generic not operational
handling code. This prevents unexpected interrupts popping up
for devices that are deemed not operational.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acting upon the assumption that cio_disable_subchannel()
is only called when we really want to disable the subchannel
(a) remove the check for activity (it is already done in
ccw_device_offline(), which is the place where it matters)
(b) collect pending status via tsch() and ignore it (it
can't matter anymore since the subchannel will be disabled).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The common I/O layer may encounter a situation where the
device number of a ccw device has changed or a device
driver doesn't want to keep a formerly disconnected device
becoming operational again. Instead of using device_del()/
device_add() as now, we can just unbind the driver from the
device and rebind it to get the desired effect (rebinding)
with less overhead.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split machine check handler code and move it to cio and kernel code
where it belongs to. No functional change.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ftrace code is currently not reentrant, so we better don't trace
our machine check handler. Machine checks are handled like NMIs on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces the kernel parameter hvc_iucv_allow= that specifies
a comma-separated list of z/VM user IDs.
If specified, the z/VM IUCV hypervisor console device driver accepts IUCV
connections from listed z/VM user IDs only.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the hvc_iucv= kernel parameter specifies a value that is not
valid, display an error message.
Minor changes to existing kernel messages.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dead file. Seems to be a leftover from the 2.4->2.5 conversion.
The used and uptodate version of this file is in arch/s390/kernel.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All in sysinfo.c is core kernel code and not driver code. So move it
to arch/s390/kernel. Also includes some small cleanups.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Moved some Messages into s390 debug feature and changed remaining
messages to use the dev_xxx and pr_xxx macros.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To support High Performance FICON, the DASD device driver has to
translate I/O requests into the new transport mode control words (TCW)
instead of the traditional (command mode) CCW requests.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd device driver will now support ECKD devices with more then
65520 cylinders.
In the traditional ECKD adressing scheme each track is addressed
by a 16-bit cylinder and 16-bit head number. The new addressing
scheme makes use of the fact that the actual number of heads is
never larger then 15, so 12 bits of the head number can be redefined
to be part of the cylinder address.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Permission is now granted to the subsystem to format write R0 with:
* an ID = CCHHR, where CC = physical cylinder number,
HH = physical head number, and R = 0
* a key length of zero
* a data length of eight
* a data field containing all zeros
Signed-off-by: Jean-Baptiste Joret <joret@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All of the ioctls are compatible. Just enable them.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide new shutdown action "dump_reipl" for automatic ipl after dump.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
With CONFIG_PROVE_LOCKING enabled
$ losetup /dev/loop0 file
$ losetup -o 32256 /dev/loop1 /dev/loop0
$ losetup -d /dev/loop1
$ losetup -d /dev/loop0
triggers a [ INFO: possible circular locking dependency detected ]
I think this warning is a false positive.
Open/close on a loop device acquires bd_mutex of the device before
acquiring lo_ctl_mutex of the same device. For ioctl(LOOP_CLR_FD) after
acquiring lo_ctl_mutex, fput on the backing_file might acquire the bd_mutex of
a device, if backing file is a device and this is the last reference to the
file being dropped . But it is guaranteed that it is impossible to have a
circular list of backing devices.(say loop2->loop1->loop0->loop2 is not
possible), which guarantees that this can never deadlock.
So this warning should be suppressed. It is very difficult to annotate lockdep
not to warn here in the correct way. A simple way to silence lockdep could be
to mark the lo_ctl_mutex in ioctl to be a sub class, but this might mask some
other real bugs.
@@ -1164,7 +1164,7 @@ static int lo_ioctl(struct block_device *bdev, fmode_t mode,
struct loop_device *lo = bdev->bd_disk->private_data;
int err;
- mutex_lock(&lo->lo_ctl_mutex);
+ mutex_lock_nested(&lo->lo_ctl_mutex, 1);
switch (cmd) {
case LOOP_SET_FD:
err = loop_set_fd(lo, mode, bdev, arg);
Or actually marking the bd_mutex after lo_ctl_mutex as a sub class could be
a better solution.
Luckily it is easy to avoid calling fput on backing file with lo_ctl_mutex
held, so no lockdep annotation is required.
If you do not like the special handling of the lo_ctl_mutex just for the
LOOP_CLR_FD ioctl in lo_ioctl(), the mutex handling could be moved inside
each of the individual ioctl handlers and I could send you another patch.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When changing DCB parameters, ixgbe needs to have the MAC reset. The way
the flow control code is setup today, PFC will be disabled on a reset.
This patch adds a new flow control type for PFC, and then has the netlink
layer take care of toggling which type of flow control to enable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Alan Cox, it is possible for e1000e to exit its interrupt
handler or NAPI with interrupts enabled even when the driver is unloading or
being configured administratively down.
fix related to fix for: http://bugzilla.kernel.org/show_bug.cgi?id=12876
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e (and e1000, igb, ixgbe, ixgb) all do a series of operations each
time a multicast address is added. The flow goes something like
1) stack adds one multicast address
2) stack passes whole current list of unicast and multicast addresses to
driver
3) driver clears entire list in hardware
4) driver programs each multicast address using iomem in a loop
This was causing multicast packets to be lost during the reprogramming
process.
reference with test program:
http://kerneltrap.org/mailarchive/linux-netdev/2009/3/14/5160514/thread
Thanks to Dave Boutcher for his report and test program.
This driver fix prepares an array all at once in memory and programs it in
one shot to the hardware, not requiring an "erase" cycle. It would still
be possible for packets to be dropped while the receiver is off during
reprogramming.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Dave Boutcher <daveboutcher@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the e1000e tx cleanup routine to more closely match
what already exists in igb and e1000.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this is in regards to
http://bugzilla.kernel.org/show_bug.cgi?id=12876
where it appears that e1000 can leave its interrupt enabled after
exiting the driver. Fix the bug by making the interrupt enable
paths more aware of the driver exiting.
Thanks to Alan Cox for the poke and initial investigation.
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx cleanup routine was stopping after 64 packets and this was causing
issues resulting in the ring not being completely cleaned.
This change updates the driver to clean the entire ring and if it doesn't
it then will retry on the next pass.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the dma mapping to better support
skb_dma_map/skb_dma_unmap and addresses and redefines the tx hang logic to
be based off of time stamp instead of if the dma field is populated
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've hit an issue on my system when I've been using RealTek RTL8139D cards in
bonding interface in mode balancing-alb. When I enslave a card, the current
active slave (bond->curr_active_slave) is not set and the link is therefore
not functional.
----
# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: None
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:1f:1f:01:2f:22
----
The thing that gets it right is when I unplug the cable and then I put it back
into the NIC. Then the current active slave is set to eth1 and link is working
just fine. Here is dmesg log with bonding DEBUG messages turned on:
----
ADDRCONF(NETDEV_UP): bond0: link is not ready
event_dev: bond0, event: 1
IFF_MASTER
event_dev: bond0, event: 8
IFF_MASTER
bond_ioctl: master=bond0, cmd=35216
slave_dev=cac5d800:
slave_dev->name=eth1:
eth1: ! NETIF_F_VLAN_CHALLENGED
event_dev: eth1, event: 8
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 1
event_dev: eth1, event: 8
IFF_SLAVE
Initial state of slave_dev is BOND_LINK_UP
bonding: bond0: enslaving eth1 as an active interface with an up link.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
event_dev: bond0, event: 4
IFF_MASTER
bond0: no IPv6 routers present
<<<<cable unplug>>>>
eth1: link down
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely down for interface eth1, disabling it
event_dev: bond0, event: 4
IFF_MASTER
<<<<cable plug>>>>
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
event_dev: eth1, event: 8
IFF_SLAVE
event_dev: eth1, event: 8
IFF_SLAVE
bonding: bond0: first active interface up!
event_dev: bond0, event: 4
IFF_MASTER
----
The current active slave is set by calling bond_select_active_slave() function
from bond_miimon_commit() function when the slave (eth1) link goes to state up.
I also tested this on other machine with Broadcom NetXtreme II BCM5708
1000Base-T NIC and there all works fine. The thing is that this adapter is down
and goes up after few seconds after it is enslaved.
This patch calls bond_select_active_slave() in bond_enslave() function for modes
alb and tlb and makes sure that the current active slave is set up properly even
when the slave state is already up. Tested on both systems, works fine.
Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to
test that.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gianfar uses a hardware header FCB for offloading. However when used
with bridging or IP forwarding, TX skb might not have enough headroom
for the FCB. Reallocate skb for such cases.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bumps the driver release date to March 25th 2009
and release version to 0.22.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the second PHY address which is strapped
to be at PHY address 3 instead of 2.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the start function in preparation of the generic watchdog code.
Also make sure that locking of the start function is OK.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Change the wdt.c watchdog driver so that the code is the same for
both the WDT500 as the WDT501-P card. The selection of the card
is now being done via the module parameter: 'type' instead of the
config option CONFIG_WDT_501.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix following includes:
* #include <asm/io.h> should be #include <linux/io.h>
* #include <asm/uaccess.h> should be #include <linux/uaccess.h>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add the PCI-ID for the upcoming new BMC controller for HP hardware.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The orion5x-wdt driver is now registered as a platform device and
receives the tclk value as platform data. This fixes a compile issue
cause by a previously removed define "ORION5X_TCLK".
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Kristof Provost <kristof@sigsegv.be>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Cc: Kunihiko IMAI <bak@d2.dion.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure that the watchdog is not running after loading
and before it is started by opening /dev/watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDT timer ticks quite fast (half of the CPU clock speed, which may
be between 198MHz and 330MHz (or 400MHz on newer boards)). Given it's
size of 32Bit, the maximum timeout value ranges from about 21s to 43s,
depending on the configured CPU clock speed.
This patch add's the timeout module parameter and checks that it's not
bigger then the maximum timeout for the given clock speed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Clean-up the rc32434 driver code:
- name the platform driver rc32434_wdt_driver
- Replace KBUILD_MODNAME ": " with PFX define.
- Cleanup include files
- Order the ioctl's
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove davinci platform-specific IO accessor macros in favor
of standard ioremap + io[read|write]* functions.
Also, convert printk(KERN_ERR ....) into dev_err(...)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I noticed the W83697UG driver tries to register a watchdog even though
it already noticed the chip isn't there.
WDT driver for the Winbond(TM) W83697UG/UF Super I/O chip initialising.
w83697ug/uf WDT: No W83697UG/UF could be found
w83697ug/uf WDT: Watchdog already running. Resetting timeout to 60 sec
w83697ug/uf WDT: cannot register miscdev on minor=130 (err=-16)
Patch propagates the error back to wdt_init().
Signed-off-by: Eric Lammerts <eric@lammerts.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
wait_event_timeout just takes the numnber of jiffies to wait as
an argument. That value does not include jiffies itself.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a recovery is started for a qeth device, additional invocations
to change a mac address, to configure a VLAN interface on top, or to
add multicast addresses should wait till recovery is finished,
otherwise recovery might fail.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth: Unregister MAC addresses from device (layer 2) during
recovery cycle. When the device is set online the MAC
addresses are registered again on the device.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performance measurements showed EDDP does not lower CPU costs but increase
them. So we dump out EDDP code from qeth driver.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics counter for software tx checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a way to provide the MAC address for ax88796 devices from
their platform data. Boards might decide to set the address
programmatically, taken from boot tags or other sources.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the ax88796 ethernet driver to take IRQ flags
given by the platform_device definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID for a new variant of the 82574 adapter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cxgb3 NIC driver can handle more firmware versions than iw_cxgb3,
and since commit 8207befa ("cxgb3: untie strict FW matching") cxgb3
will load with firmware versions that iw_cxgb3 can't handle. The FW
major number indicates a specific interface between the FW and
iw_cxgb3. Thus if the major number of the running firmware does not
match the required version compiled into iw_cxgb3, then iw_cxgb3 must
not register that device.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On a timeout call a device specific handler early in the recovery so that
we can complete and process successful commands which timed out due to IRQ
loss or the like rather more elegantly.
[Revised to exclude the timeout handling on a few devices that inherit from
SFF but are not SFF enough to use the default timeout handler]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If the device is signalling that there is data to drain after an error we
should read the bytes out and throw them away. Without this some devices
and controllers get wedged and don't recover.
Based on earlier work by Mark Lord
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ahci_transmit_led_message saves off the led_state
with a value that includes the port number OR'd
in, this incorrect value maybe reported back
in ahci_led_store.
For instance, if you turn off all the leds for
port 1 and cat the value back it will report 1
instead of 0.
# echo 0 > /sys/class/scsi_host/host1/em_message
# cat /sys/class/scsi_host/host1/em_message
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make libata more robust when parsing the multi_count
field from a drive's identify data. This prevents us from
attempting to use dubious multi_count values ad infinitum.
Reset dev->multi_count to zero and reprobe it each time
through this routine, as it can change on device reset.
Also ensure that the reported "maximum" value is valid
and is a power of two, and that the reported "count" value
is valid and also a power of two. And that the "count"
value is not greater than the "maximum" value.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For Marvell SoC chips, the HDD LED does not blink when there is
disk I/O if NCQ is enabled. Add a quirk that enables blink mode for
the LED while NCQ is enabled on any port of a SoC host controller.
Normal LED function is restored when NCQ is not enabled on any port.
The code to enable the blink mode is based on earlier code
and suggestions from Frans Pop, Saeed Bishara, and possibly others.
Signed-off-by: Mark Lord <mlord@pobox.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable use of the "all ports" IRQ coalescing optimization
for GEN_II / GEN_IIE chips that have dual host-controllers (8-ports).
Currently only the 6081 chip qualifies, but other chips may come along someday.
Rather than each half of the chip having to satisfy a local set of coalescing thresholds,
use of this feature groups all ports together under a single set of thresholds.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add IRQ coalescing to sata_mv (off by default).
This feature can reduce total interrupt overhead for RAID setups
in some situations, by deferring the interrupt signal until one or both of:
a) a specified io_count (completed SATA commands) is achieved, or
b) a specified time interval elapses after an IO completion.
For now, module parameters are used to set the irq_coalescing_io_count
and irq_coalescing_usecs (timeout) globally. These may eventually
be supplemented with sysfs attributes, so that thresholds can be set
on-the-fly and on a per-chip (or even per-host_controller) basis.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Various cosmetic changes in preparation for the IRQ coalescing feature.
Note that the various MV_IRQ_COAL_* definitions are restored/renamed
in the folloup patch which adds IRQ coalescing to the driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
platform_get_irq() can return -ENXIO, but since 'irq' is an
unsigned int, it does not show when the IRQ resource wasn't found.
Make irq an int so that we can use a single variable to test the
platform_get_irq() return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to Alan:
>and yes the EFAR does UDMA66.
mwdma:
>Yep - wrong comment. The EFAR is a sort of clone of the PIIX and I
>copied the comment while EFAR don't appear to have copied the
>limitation
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As noted by Alan:
>Your suspicions are correct here btw - the device can only do MWDMA1 and
>MWDMA2 (much like some PIIX devices)
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Blacklist HP Compaq 6720s so that it doesn't play a "spin down,
spin up, spin down" ping-pong with the hard disk during system
power off.
Signed-off-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is initially needed to work around NCQ errata,
whereby the READ_LOG_EXT command sometimes fails
when issued in the traditional (sff) fashion.
Portions of this code will likely be reused for
implementation of the target mode feature later on.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is necessary for use with the upcoming "mv_qc_issue_fis()" patch,
but is being added separately here for easier code review.
When using command issue via the "mv_qc_issue_fis()" mechanism,
the initial ATA_BUSY bit does not show in the ATA status (shadow) register.
This can confuse libata! So here we add a hook to fake ATA_BUSY
for that situation, until the first time a BUSY, DRQ, or ERR bit is seen.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so that it doesn't miss any protocols. Handle future cases where a
qc is specially marked for polled issue or where a particular chip
version prefers interrupts over polling for PIO.
This mimics the polling decision logic from ata_sff_qc_issue().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This also gets rid of any need for mv_mode_filter().
Using basic DMA on GEN_IIE requires setting an undocumented
bit in an undocumented register. For safety, we clear that
bit again when switching back to EDMA mode.
To avoid a performance penalty when switching modes,
we cache the register in port_priv, as already done for other regs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Maintain a local (mv_port_priv) cache of frequently accessed registers,
to avoid having to re-read them (very slow) on every transistion
between EDMA and non-EDMA modes. This speeds up things like
flushing the drive write cache, and anything using basic DMA transfers.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no need to turn off intx explicitly on msi enable. This is
automatically handled by pci. Drop it.
This might be needed on machines if the BIOS turns intx off during
boot. However, there's no evidence of such behavior for ahci and
the only such case seems to be ICH5 PATA according to ata_piix.
Also, given the way ahci operates, it's highly unlikely BIOS ever
disables IRQ for the controller. However, as this change has slight
possibility of introducing failure, please schedule it for #upstream.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I'm not quite sure what freezing and thawing is used for. Tests showed
that the port is being frozen at initialisation state and thawed right
afterwards, then the functions were not called anymore. Dropping the
complete custom code for handling the frozen state seems to work at
least for a standard use case including mounting a partition, copying
some files in it (in parallel) and finally removing them and unmounting
the partition.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The biggest difference between rb532_pata_data_xfer() and
ata_sff_data_xfer32() is the call to ata_sff_pause() at the end of
rb532_pata_data_xfer() which I suppose to be unnecessary since it works
without. I've also tested using ata_sff_data_xfer() as replacement, but
since we know that the driver supports 32bit IO, using the optimised
version should be safe.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only difference between rb532_pata_exec_command() and
ata_sff_exec_command() is added debugging output, so it can be dropped
and the standard op used instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the delay used internally is just the same as ata_sff_pause()
uses, rb532_pata_finish_io() does exactly the same as ata_sff_pause()
and thus can be replaced by the later one.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove redundant code left over from the earlier patch 04/07.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Try and avoid unnecessary reconfiguration of the EDMA config register
on every single non-EDMA I/O operation, by moving the call to
mv_edma_cfg() into mv_stop_edma(). It must then also be invoked
from mv_hardreset() and from mv_port_start().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ATAPI support to sata_mv, using sff DMA for GEN_II chipsets,
and plain old PIO for GEN_IIE.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix mv_fill_sg() to zero out the reserved word (required for ATAPI),
and to include a memory barrier. This may also help with problems
reported by Jens on the PPC platform.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update the logic in ata_qc_from_tag() to match that used
in similar places elsewhere in libata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange logic in mv_qc_issue() to handle protocols
other than ATA_PROT_DMA, ATA_PROT_NCQ, and ATA_PROT_PIO.
This is in preparation for later enabling ATAPI support.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_start_dma() and friends, in preparation for adding
non-EDMA DMA modes, and non-EDMA interrupts, to the driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up the chipset GENeration FLAGS, and rename them
for consistency with other uses of GEN_XX within sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hi, Pls accept this patch to cleanup rx/tx rate calculations as follows:
- check for jiffies wraparound
- remove typecast of a denominator
- do rate calculation only in workqueue context periodically
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only way for a sysfs attribute to remove itself (without
deadlock) is to use the sysfs_schedule_callback() interface.
Vegard Nossum discovered that a poorly written sysfs ->store
callback can repeatedly schedule remove callbacks on the same
device over and over, e.g.
$ while true ; do echo 1 > /sys/devices/.../remove ; done
If the 'remove' attribute uses the sysfs_schedule_callback API
and also does not protect itself from concurrent accesses, its
callback handler will be called multiple times, and will
eventually attempt to perform operations on a freed kobject,
leading to many problems.
Instead of requiring all callers of sysfs_schedule_callback to
implement their own synchronization, provide the protection in
the infrastructure.
Now, sysfs_schedule_callback will only allow one scheduled
callback per kobject. On subsequent calls with the same kobject,
return -EAGAIN.
This is a short term fix. The long term fix is to allow sysfs
attributes to remove themselves directly, without any of this
callback hokey pokey.
[cornelia.huck@de.ibm.com: s390 ccwgroup bits]
Reported-by: vegard.nossum@gmail.com
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dpm_list currently relies on the fact that child devices will
be registered after their parents to get a correct suspend
order. Using device_move() however destroys this assumption, as
an already registered device may be moved under a newly registered
one.
This patch adds a new argument to device_move(), allowing callers
to specify how dpm_list should be adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements uevent suppress in kobject and removes it
from struct device, based on the following ideas:
1,Uevent sending should be one attribute of kobject, so suppressing it
in kobject layer is more natural than in device layer. By this way,
we can do it for other objects embedded with kobject.
2,It may save several bytes for each instance of struct device.(On my
omap3(32bit ARM) based box, can save 8bytes per device object)
This patch also introduces dev_set|get_uevent_suppress() helpers to
set and query uevent_suppress attribute in case to help kobject
as private part of struct device in future.
[This version is against the latest driver-core patch set of Greg,please
ignore the last version.]
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During bootup performance tracing I noticed many occurrences of
vca* device creation and removal, leading to the usual userspace
uevent processing, which are, in this case, rather pointless.
A simple test showing the kernel timing (not including all the
work userspace has to do), gives us these numbers:
$ time for i in `seq 1000`; do echo a > /dev/tty2; done
real 0m1.142s
user 0m0.015s
sys 0m0.540s
If we move the hook for the vcs* driver core devices from the
tty "binding" to the vc allocation/deallocation, which is what
the vcs* devices represent, we get the following numbers:
$ time for i in `seq 1000`; do echo a > /dev/tty2; done
real 0m0.152s
user 0m0.030s
sys 0m0.072s
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We will remove platform_data field from struct device until
all platform devices pass its specific data from platfom_device
and all platform drivers use platform specific data passed by
platform_device->platform_data. This kind of conversion will
need a long time, for thousands of files is affected.
To make the conversion easily, we allow platform specific data
passed by struct device or struct platform_device and platform
driver may use it from struct device or struct platform_device.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves platform_data from struct device into
struct platform_device, based on the two ideas:
1. Now all platform_driver is registered by platform_driver_register,
which makes probe()/release()/... of platform_driver passed parameter
of platform_device *, so platform driver can get platform_data from
platform_device;
2. Other kind of devices do not need to use platform_data, we can
decrease size of device if moving it to platform_device.
Taking into consideration of thousands of files to be fixed and they
can't be finished in one night(maybe it will take a long time), so we
keep platform_data in device to allow two kind of cases coexist until
all platform devices pass its platfrom data from
platform_device->platform_data.
All patches to do this kind of conversion are welcome.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nothing outside of the driver core should ever touch knode_bus, so
move it out of the public eye.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nothing outside of the driver core should ever touch knode_driver, so
move it out of the public eye.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nothing outside of the driver core should ever touch klist_children, or
knode_parent, so move them out of the public eye.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is to be used to move things out of struct device that no code
outside of the driver core should ever touch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes 100ms polling for driver_probe_done in
wait_for_device_probe(), and uses wait_event() instead.
Removing polling in fs initialization may lead to
a faster boot.
This patch also changes the return type of wait_for_device_done()
from int to void.
This patch is against Arjan's patch in linux-next tree.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the bus_type is not registerd, driver_register to that bus will cause oops.
I found this bug when test built-in usb serial drivers (ie. aircable driver)
with 'nousb' cmdline params.
In this patch:
1. set the bus->p=NULL when bus_register failed and unregisterd.
2. if bus->p is NULL, driver_register BUG_ON will be triggered.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch from Ming Lei <tom.leiming@gmail.com> entitled:
platform driver: fix incorrect use of 'platform_bus_type' with 'struct devic
introduced the following warnings on m68k, as `dev' is now a `struct
platform_device *' instead of a `struct device *':
| drivers/scsi/a4000t.c:64: warning: passing argument 3 of 'NCR_700_detect' from incompatible pointer type
| drivers/scsi/mvme16x_scsi.c:67: warning: passing argument 3 of 'NCR_700_detect' from incompatible pointer type
| drivers/scsi/bvme6000_scsi.c:61: warning: passing argument 3 of 'NCR_700_detect' from incompatible pointer type
I think the below is missing (untested on real hardware).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a UIO memory region does not start on a page boundary but straddles one,
the number of actual pages that overlap the memory region may be calculated
incorrectly because the offset isn't taken into account. If userspace sets
the mmap length to offset+size, it may fail with -EINVAL if UIO thinks it's
trying to allocate too many pages.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UIO driver for the Adrienne Electronics Corporation PCI time code
device.
This device differs from other UIO devices since it uses I/O ports instead of
memory mapped I/O. In order to make it possible for UIO to work with this
device a utility, uioport, can be used to read and write the ports.
uioport is designed to be a setuid program and checks the permissions of
the /dev/uio* node and if the user has write permissions it will use
iopl and out*/in* to access the device.
[1] git clone git://ifup.org/philips/uioport.git
Signed-off-by: Brandon Philips <brandon@ifup.org>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a UIO device has several memory mappings, it can be difficult for userspace
to find the right one. The situation becomes even worse if the UIO driver can
handle different versions of a card that have different numbers of mappings.
Benedikt Spranger has such cards and pointed this out to me. Thanks, Bene!
To address this problem, this patch adds "name" sysfs attributes for each
mapping. Userspace can use these to clearly identify each mapping. The name
string is optional. If a driver doesn't set it, an empty string will be
returned, so this patch won't break existing drivers.
The same problem exists for port region information, so a "name" attribute is
added there, too.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now platform_device is being widely used on SoC processors where the
peripherals are attached to the system bus, which is simple enough.
However, silicon IPs for these SoCs are usually shared heavily across
a family of processors, even products from different companies. This
makes the original simple driver name based matching insufficient, or
simply not straight-forward.
Introduce a module id table for platform devices, and makes it clear
that a platform driver is able to support some shared IP and handle
slight differences across different platforms (by 'driver_data').
Module alias is handled automatically when a MODULE_DEVICE_TABLE()
is defined.
To not disturb the current platform drivers too much, the matched id
entry is recorded and can be retrieved by platform_get_device_id().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This helps the code look more consistent and cleaner.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves bus->match out from driver_probe_device and
does not hold device lock to check the match between a device
and a driver.
The idea has been verified by the commit 6cd4958609,
which leads to a faster boot. But the commit 6cd4958609 has
the following drawbacks: 1),only does the quick check in
the path of __driver_attach->driver_probe_device, not in other
paths; 2),for a matched device and driver, check the same match
twice. It is a waste of cpu ,especially for some drivers with long
device id table (eg. usb-storage driver).
This patch adds a helper of driver_match_device to check the match
in all paths, and testes the match only once.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that all users of bus_id is gone, we can remove it from struct
device.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace references to bus_id with dev_name() to fix fhci driver build break.
drivers/usb/host/fhci-hcd.c:586: error: struct device has no member named bus_id
drivers/usb/host/fhci-hcd.c:653: error: struct device has no member named bus_id
drivers/usb/host/fhci-dbg.c:111: error: struct device has no member named bus_id
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update myri10ge firmware headers to firmware version 1.4.41.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed unused variable dev
Signed-off-by: vibi sreenivasan <vibi_sreenivasan@cms.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data read from the SKIPMAP registers is not immediately available
after writing and the driver panics when a packet is enqueued from the
interrupt handler. This patch adds an ndelay(195) before these registers
are read (delay value mentioned in section 15.1.1.3 of the ISP1760 data
sheet).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an USB hardware does not provide a valid LANGID, fall back to value
zero which is still a reasonable default for most devices.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a merge of patches :
- fix function doc and debug
- cleanup loop count
- optimize code to remove local variable and extra check
- init 'req' before use
- add missing iounmap call
[dbrownell@users.sourceforge.net: capitalize IN/OUT directions in doc]
Signed-off-by: Vernon Sauder <vsauder@inhand.com>
[folded by Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the new device-level suspend/resume hooks for Gadget Zero;
always enable them with the OTG test mode; and support remote
wakeup on both configurations even in non-OTG mode.
This ensures that both configurations can pass the USBCV remote
wakeup tests when the OTG test mode is enabled. This changes
behavior by adding autoresume support to the loopback config
even in non-OTG mode; the test failure was that it didn't work
in OTG mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Address one open question in the composite gadget framework:
Yes, we should have device-level suspend/resume callbacks
in addition to the function-level ones. We have at least one
scenario (with gadget zero in OTG test mode) that's awkward
to handle without it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the problem that system cannot suspend.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
transfer_buffer_length and actual_length have become unsigned, therefore some
additional conversion of local variables, function arguments and print
specifications is desired.
A test for a negative urb->transfer_buffer_length became obsolete; instead
we ensure that it does not exceed INT_MAX. Also, urb->actual_length is always
less than urb->transfer_buffer_length.
rh_string() does no longer return -EPIPE in the case of an unsupported ID.
Instead its only caller, rh_call_control() does the check.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is really a follow up to the modifications Alan Cox made for commit
95da310e66 to pass a tty_struct to various
interface functions, which broke the serial configuration (termios) functions
when the device is being used as a console. These changes restore the
configuration to proper functioning both as a tty and as a console. As Alan
notes in that commit, these changes will need to be tweaked when we have
a proper console abstraction.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ipaq driver currently enforces one port on all devices. This
is correct for 2 and 3 endpoint devices, but with 4 endpoint devices
meaningful communication occurs on the second pair.
This patch allows 2 ports for 4 endpoint devices.
Signed-off-by: Mark Ellis <mark@mpellis.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb-control.h is needed by ohci-s3c2410.c for both S3C24XX and S3C64XX
architectures, so move it to <plat/usb-control.h>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ohci-s3c2410.c glue supports both CONFIG_ARCH_S3C2410 and
CONFIG_ARCH_S3C64XX so add it to the build of ohci-s3c2410.c
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this sparse warning:
drivers/usb/host/oxu210hp-hcd.c:2687:42: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB bus clock is usb-bus-host, so print the correct name in the
dev_err() statement if we cannot find it.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Remove the include of <mach/hardware.h>, as no definitions
from it are used by the OHCI driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lots of users are getting confused about the cp2101 driver. It really
does support more than just the cp2101 device, so rename it to cp210x to
try to prevent confusion.
Cc: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch lowers the logging priority of certain messages to prevent
users from flooding the log files.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the extended range of baud rates supported
by CP2102 and CP2103 devices described in SiLabs AN205. An additional
function cp2101_quantise_baudrate rounds the baud rate as per AN205
Table 1. A modification to the baud rate calculation removes a rounding
error, allowing the full range of baud rates to be used.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzfree() instead of memset() + kfree().
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1223) removes a bunch of unnecessary "inline"
annotations from the usbfs driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1221) changes the way usbcore reinitializes a device
following a reset or a reset-resume. Currently we call
usb_set_interface() for every interface in the active configuration;
this is to put the interface into the same altsetting as before the
reset and to make sure that the host's endpoint state matches the
device's endpoint state.
However, sending a Set-Interface request is a waste of time if an
interface was already in altsetting 0 before the reset, since it is
certainly in altsetting 0 afterward. In addition, many devices can't
handle Set-Interface requests -- they crash when they receive them.
So instead, the patch adds code to check each interface. If the
interface wasn't in altsetting 0 before the reset, we go head with the
Set-Interface request as before. But if it was then we skip sending
the Set-Interface request, and we clear out the host-side endpoint
state by calling usb_disable_interface() followed by
usb_enable_interface().
The patch also adds a couple of new comments to explain what's going
on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
actual_length should also be a u32 and not a signed value. This patch
changes this field to be 'u32' to prevent any potential negative
conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roel Kluin pointed out that transfer_buffer_lengths in struct urb was
declared as an 'int'. This patch changes this field to be 'u32' to
prevent any potential negative conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code in uhci-q.c doesn't have to use pseudo-negative values. I did
it that way because it was easy and because it would give the expected
output during debugging. But it doesn't have to work that way. Here's
another approach.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch disables USB regulators VUSB1V5, VUSB1V8, and VUSB3V1
when the USB cable is unplugged to reduce power consumption.
Added a depencency from twl4030 usb driver to TWL_REGULATOR.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an extension to the binary API so it reaches parity with
existing text API (so-called "1u"). The extension delivers additional data,
such as ISO descriptors and the interrupt interval.
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following bug:
.plug ch341 usb serial port into a hub port;
.ch341 driver bound to the device and /dev/ttyUSB0 comes
.open /dev/ttyUSB0 by minicom and we can use the serial successfully
.suspend the ch341 usb serial device(such as: echo suspend > power/level)
.resume the ch341 usb serial device (such as: echo on > power/level)
.new port /dev/ttyUSB1 comes ,and the original /dev/ttyUSB0 still exists,
but is no longer usable by minicom
The patch adds suspend and resume callback to ch341 usb driver to prevent it
from unbinding during suspend. The /dev/ttyUSB0 is not released until being
closed, so /dev/ttyUSB1 comes after resume, and the original /dev/ttyUSB0 is
no longer usable by minicom. It is really a mess for a minicom user.
This patch also adds the reset_resume callback to make it usable after resuming
from STR or hibernation, for generally STR or hibernation will make the vbus
of root-hub lost.
Finally enable the driver's supports_autosuspend, for the device is in working
order with it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial support for DaVinci DM355, on the EVM board; peripheral
mode should work, once mainline merges DM355 support. Missing:
(a) renumbering the GPIO for DRVVBUS on the DM6446 EVM,
when DAVINCI_N_GPIO increases;
(b) disabling DM355_DEEPSLEEP.DRVVBUS_OVERRIDE so VBUS is
driven according to the ID signal, if cpu_is_..._dm355()
The new PHY control bits are ignored on DM6446.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Except on DaVinci, VBUS is now switched off as part of idling the
USB link (after a_wait_bcon) whenever a device is disconnected
from host. This is correct for OTG hosts, where either SRP or
an ID interrupt could turn VBUS on again.
However, for non-OTG hosts there's no way to turn VBUS on again,
so the host becomes unusable. And the procfs entry which once
allowed a manual workaround for this is now gone.
This patch adds an is_otg_enabled() check before scheduling the
switch-off timer in disconnect path, supporting a "classic host"
mode where SRP is unavailable.
[ dbrownell@users.sourceforge.net: tweak patch description ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct musb_read_fifosize() and musb_configure_ep0() functions
for the #ifndef BLACKFIN branch when the silicon uses static FIFO
configuration. (Most current silicon configures this controller
to use dynamic FIFO configuration; some parts from ST don't, like
the STM STA2062.)
Signed-off-by: Giuseppe GORGOGLIONE <giuseppe.gorgoglione@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes endpoint starvation issue when more than one bulk QH is
multiplexed on the reserved bulk RX endpoint, which is normal
for cases like serial and ethernet adapters.
This patch sets the NAK timeout interval for such QHs, and when
a timeout triggers the next QH will be scheduled. (This resembles
the bulk scheduling done in hardware by EHCI, OHCI, and UHCI.)
This scheme doesn't work for devices which are connected to a
high to full speed tree (transaction translator) as there is
no NAK timeout interrupt from the musb controller from such
devices.
Tested with PIO, Inventra DMA, CPPI DMA.
[ dbrownell@users.sourceforge.net: fold in start_urb() update;
clarify only for bulk RX; don't accidentally clear WZC bits ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current MUSB host code doesn't make use of all the available
FIFOs in for periodic transfers since it wrongly assumes the RX
and TX sides of any given hw_ep always share one FIFO.
Change: use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep'
to check the endpoint's business; get rid of the now-unused 'periodic'
array in the 'struct musb'. Also optimize a loop induction variable
in the endpoint lookup code.
(Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>)
[ dbrownell@users.sourceforge.net: clarify description and origin
of this fix; whitespace ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To permit a userspace application to associate with WUSB devices
using numeric association, control transfers to unauthenticated WUSB
devices must be allowed.
This requires that wusbcore correctly sets the device state to
UNAUTHENTICATED, DEFAULT and ADDRESS and that control transfers can be
performed to UNAUTHENTICATED devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The lack of a MODULE_LICENSE macro in ums-* subdrivers prevented them
from loading. Needs to be applied after Alan Stern's usb-storage
subdriver separation patchset. Also added missing MODULE_DESCRIPTION and
MODULE_AUTHOR entries.
Signed-off-by: Maciej Grela <maciej.grela@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1217) converts usb-storage's onetouch subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1216) converts usb-storage's karma subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1215) converts usb-storage's alauda subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1214) converts usb-storage's jumpshot subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1213) converts usb-storage's datafab subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
