CM-X300 can be assembled with different NAND flashes from different
manufacturers. Adding their configuration to the kernel is impractical,
therefore we will use the default NAND controller settings set up by the
bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Setup gpio-keys for EzX phones
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add a call to pxa_set_ac97_info() to enable the audio support.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
csb726 used obsolete and not working out-of-tree driver smc911x.
Switch it to use new smsc911x driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add voltage regulation capability to pxa2xx cpufreq
driver. The cpufreq will ask for a "vcc_core" regulator to
the regulator framework.
If a regulator is found at probe time, it will be used with
values specified in PXA270 Electrical, Mechanical, and
Thermal Specifications.
If not, it will be assumed for now that frequency change
will work without voltage control. This assumes that the
IPL/SPL installs sane values to an existing voltage
regulator (ie. voltage high enough to support the full
range).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA processors have several low-power modes. Currently kernel supports
only one of these modes for PM_SUSPEND_MEM.
This patch adds ability to set desired suspend mode for PXA27x based
machines.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
As reported by Aric Blumer, the pxa27x_udc driver does work
with pxa3xx devices. Add support into device files.
Reported-by: Aric Blumer <aric@sdgsystems.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Matt Reimer <mattjreimer@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The default value is 16 IRQs. Zylonite needs 32, ASIC3 based boards need 70.
My problem is still that due to the way IRQ_GPIO is hardcoded, ASIC3 based boards
need 70 IRQs starting at IRQ_BOARD_START. If I define ASIC3 IRQs similar to LoCoMo
or SA1111, things break as soon as something selects PXA_HAVE_BOARD_IRQS.
Increasing the default number of board IRQs to 70 instead doesn't seem very nice.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The PXA_PWM config option is really redundant since the introduction
of HAVE_PWM, replace that with HAVE_PWM to avoid confusion.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PWMs on PXA168/910 start at number 1 instead of 0, (i.e. PWM1/2/3/4 instead
of PWM0/1/2/3 on PXA25x/PXA27x/PXA3xx). Allow this number to be specified
in pwm_id_table.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Currently spitz_ohci_init() that requests GPIO doesn't have
corresponding spitz_ohci_exit() which will gpio_free(). This causes
minor problems e.g. during resume when the OHCI device can't be resumed.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
'mach-pxa' platforms currently rely on a bootloader to setup GPIO pins
and clear RDH (to enable inputs).
A kernel loaded by a 'minimal' bootloader, that doesn't touch any pins,
will not function correctly; inputs will remain disabled, even after the
pins are configured. The following change fixes the issue and has been
verified on Gumstix Verdex XL6P and a custom PXA270 platform.
Signed-off-by: Timothy Clacy <tcl@phaseone.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
I want to reuse tosa/spitz gpio_reset code, but my board needs the reset
gpio to be driven high during normal operation.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Compilation for this board yields the following errors:
arch/arm/mach-pxa/viper.c:511: error: 'FFUART' undeclared here (not in a function)
arch/arm/mach-pxa/viper.c:520: error: 'BTUART' undeclared here (not in a function)
arch/arm/mach-pxa/viper.c:529: error: 'STUART' undeclared here (not in a function)
Fix them by including the necessary header.
Signed-off-by: Ricardo Martins <rasm@fe.up.pt>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GPIO17_SDATA_IN_1 and GPIO36_SDATA_IN_1 are originally designed for the 2nd
codec but unused on the board, yet they are initialized incorrectly by the
bootloader as the SDATA_IN_1 alternate function, thus causing AC97 fail to
work. Fix this issue by configuring these pins as normal GPIO to avoid the
noise from these pins being treated as signals from the 2nd codec.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
