Received frames must be re-clocked by the local XGXS to the 156.25 MHz
(DDR) clock of the XGMII. If the remote clock is slightly faster this
can reduce a minimum IPG of 64 bit-times (1 cycle) to 32 bit-times
(half a cycle). If the XMAC detects that a frame has reached the
maximum RX frame length in the same cycle that it receives one of
these reduced IPGs, it may miss the IPG, causing two valid frames to
be treated as a single invalid frame (over-length with bad CRC).
We work around this by increasing the maximum RX frame length so that
peers with matched MTU will not provoke this bug.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.
Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculate a score for each 1000 IRQs:
- TX completions are worth 1 point
- RX completions are worth 4 if merged using LRO or 2 otherwise
Reduce moderation if the score is less than 10000, down to a minimum
of 5 us. Increase moderation if the score is more than 20000, up to
the specified maximum.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reinitialise LEDs after overriding them for identification.
Rename set_fault_led method to set_id_led since we always use it for
NIC identification and not faults.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new PHY supporting SFP+ modules, used in the SFN4112F
reference design. It is similar to the QT2022C2 and shares much of
its support code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset. This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.
Remove claimed support for 100M HD mode since it is not supported by
current firmware.
Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.
Always set the AN selector bits to 1 (802.3).
Fix confusion between Next Page and Extended Next Page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sfc invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
Everything should appear identical to the user except that the
offload is now controlled by the GRO ethtool option instead of
LRO. I've kept the lro module parameter as is since that's for
compatibility only.
I have eliminated efx_rx_mk_skb as the GRO layer can take care
of all packets regardless of whether GRO is enabled or not.
So the only case where we don't call GRO is if the packet checksum
is absent. This is to keep the behaviour changes of the patch to
a minimum.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the PHY type names are overly generic. Change them to include
the model numbers of the PHYs they represent.
Correct the model number reference at the top of xfp_phy.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add type codes for the new PHY and rename the SFX7101 type code.
Add definition of clause 22 extension MMD.
Adapt the 10Xpress SFX7101 code to support the SFT9001 as well.
Clean up register definitions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
MAC, PHY and board events may be separately enabled and signalled.
Our current arrangement of chaining the polling functions can result
in events being missed. Change them to be more independent.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for auto-negotiation of speed, duplex and flow
control.
When using 10Xpress, auto-negotiate flow control. While we're
at it, clean up the code to warn when partner is not 10GBASE-T
capable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce
an efx_mac_operations structure with implementations for the two MACs.
Switch between the MACs as necessary.
PHY settings are independent of the MAC, so add get_settings() and
set_settings() to efx_phy_operations. Also add macs field to indicate
which MACs the PHY is connected to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace efx_nic::link_options bitfield with link_speed (speed in
Mbit/s) and link_fd (full duplex flag).
Remove broken auto-negotiation functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate IRQs with the name format <device>[-<type>]-<number> so that
future versions of irqbalanced understand what we're doing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a bidirectional forwarding test, we find that the best performance
is achieved by sending the TX completion interrupts from one NIC to a
CPU which shares an L2 cache with RX completion interrupts from the
other NIC. To facilitate this, add an option (through a module
parameter) to create separate channels for RX and TX completion with
separate IRQs when MSI-X is available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each reset is serialised by the rtnl_lock anyway, so there's no win
per-NIC.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add board monitoring to periodic work whenever link is down.
For SFE4001, report when a fault has caused the PHY to turn off.
For SFE4002, switch XFP PHY into low-power state in case of a fault.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The boot code that appears as a PCI expansion ROM on the SFC4000 is
stored in flash. Expose this as a standard MTD device to allow for
in-place upgrades.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some buffers we use a starting offset of either NET_IP_ALIGN or 0
depending on whether we believe the architecture supports efficient
access to unaligned words. There is now a config macro specifying
whether this is the case, so check that rather than checking for
specific architectures.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Increase the potential retry count for RX flushes from 5 to 100.
Stop polling the RX_DESC_PTR_TBL to infer that a flush might have
happened. Instead absolutely rely on the flush events, unless bug 7803
applies (Falcon rev A only).
To keep things quick, request flushes for every TX and RX queue up
front, and match up the events to requests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There was a bug in XAUI synchronisation in early 10Xpress firmware
versions. This is fixed in released firmware and we do not need to
work around it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was originally a kludge to fix broken locking, which has since
been fixed properly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Include PMA/PMD in loopback self-tests as intended.
Add NVRAM checksum validation and include it in self-tests.
Add register self-tests.
Run PHY self-tests where available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows updating PHY firmware for one interface without removing
all other interfaces handled by the driver.
Replace tx_disabled flags and 10Xpress status enumeration with flags in
enum efx_phy_mode.
Prevent an interface from being brought up while in PHY flash mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently each channel can have at most one RX queue, so go straight to
that one.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rename efx_nic::rss_queues to the more obvious n_rx_queues
Remove efx_rx_queue::used and other stuff that's redundant with it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
efx_channel::has_interrupt is redundant with efx_channel::used_flags.
Remove efx_test_eventq() because it is now obviously unreachable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Extend the SPI device setup code to support this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.
Remove some redundant boolean temporaries.
Rename one field that looks like a flag but isn't.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unmap_addr since it can be calculated from dma_addr, len and
unmap_len. This saves 4-16 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Checksum generation is an attribute of our hardware TX queues, not TX
descriptors. We previously used a single queue and turned checksum
generation on or off as requested through ethtool. However, this can
result in regenerating checksums in raw packets that should not be
modified. We now create 2 hardware TX queues with checksum generation
on or off. They are presented to the net core as one queue since it
does not know how to select between them.
The self-test verifies that a bad checksum is unaltered on the queue
with checksum generation off.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This means the compiler doesn't need to use real division instructions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This avoids deadlock in case a reset is triggered during self-test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove our own implementation of I2C bit-banging.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This driver has diverged from the out-of-tree driver to which the version
number originally applied. It should be identified primarily by kernel
version.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Also change type of efx_nic_type::max_dma_mask to u64, matching
pci_dma_supported() parameter type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This should make the driver work on 32-bit systems with 64-bit PCI support.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a set of self-tests accessible thorugh ethtool.
Add hardware loopback and TX disable control code to support them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
