* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (260 commits)
usb: renesas_usbhs: fixup inconsistent return from usbhs_pkt_push()
usb/isp1760: Allow to optionally trigger low-level chip reset via GPIOLIB.
USB: gadget: midi: memory leak in f_midi_bind_config()
USB: gadget: midi: fix range check in f_midi_out_open()
QE/FHCI: fixed the CONTROL bug
usb: renesas_usbhs: tidyup for smatch warnings
USB: Fix USB Kconfig dependency problem on 85xx/QoirQ platforms
EHCI: workaround for MosChip controller bug
usb: gadget: file_storage: fix race on unloading
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
USB: ftdi_sio.c:Fill MSR fields of the ftdi async_icount structure
USB: ftdi_sio.c: Fill LSR fields of the ftdi async_icount structure
USB: ftdi_sio.c:Fill TX field of the ftdi async_icount structure
USB: ftdi_sio.c: Fill the RX field of the ftdi async_icount structure
USB: ftdi_sio.c: Basic icount infrastructure for ftdi_sio
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
USB: ftdi_sio: Support TI/Luminary Micro Stellaris BD-ICDI Board
USB: Fix runtime wakeup on OHCI
xHCI/USB: Make xHCI driver have a BOS descriptor.
usb: gadget: add new usb gadget for ACM and mass storage
...
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
mm: memory hotplug: Check if pages are correctly reserved on a per-section basis
Revert "memory hotplug: Correct page reservation checking"
Update email address for stable patch submission
dynamic_debug: fix undefined reference to `__netdev_printk'
dynamic_debug: use a single printk() to emit messages
dynamic_debug: remove num_enabled accounting
dynamic_debug: consolidate repetitive struct _ddebug descriptor definitions
uio: Support physical addresses >32 bits on 32-bit systems
sysfs: add unsigned long cast to prevent compile warning
drivers: base: print rejected matches with DEBUG_DRIVER
memory hotplug: Correct page reservation checking
memory hotplug: Refuse to add unaligned memory regions
remove the messy code file Documentation/zh_CN/SubmitChecklist
ARM: mxc: convert device creation to use platform_device_register_full
new helper to create platform devices with dma mask
docs/driver-model: Update device class docs
docs/driver-model: Document device.groups
kobj_uevent: Ignore if some listeners cannot handle message
dynamic_debug: make netif_dbg() call __netdev_printk()
dynamic_debug: make netdev_dbg() call __netdev_printk()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
The problem is related to the early enabling of interrupts and the
per cpu timer setup before the cpu is marked online. This doesn't
need to be done in order to call calibrate_delay().
calibrate_delay() monitors jiffies, which are updated from the CPU
which is waiting for the new CPU to set the online bit.
So simply calibrate_delay() can be called on the new CPU just from
the interrupt disabled region and move the local timer setup after
stored the cpu data and before enabling interrupts.
This solves both the cpu_online vs. cpu_active problem and the
affinity setting of the per cpu timers.
Signed-off-by: Thomas Gleinxer <tglx@linutronix.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows mapping external memory such as SRAM for use.
This is needed for some small chunks of code, such as reprogramming
SDRAM memory source clocks that can't be executed in SDRAM. Other
use cases include some PM related code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If two requests have been submitted and one of them is running, if you
call pl330_chan_ctrl(ch_id, PL330_OP_START), there's a window of time
between the spin_lock_irqsave() and the _state() check in which the
running transaction may finish. In that case, we don't receive the
interrupt (because they are disabled), but _start() sees that the DMA
is stopped, so it starts it. The problem is that it sends the
transaction that has just finished again, because pl330_update()
hasn't mark it as done yet.
This patch fixes this race condition by not calling _start() if the
DMA is already executing transactions. When interrupts are reenabled,
pl330_update() will call _start().
Reference: <1317892206-3600-1-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
v2:
- register_syscore_ops(&s3c24xx_irq_syscore_ops) does not need to be
conditionally compiled out, it is already optimized out on !CONFIG_PM
- fix also s3c2412 and s3c2416 affected by the same build issue
v1:
s3c2440.c fails to build if !CONFIG_PM because in such case
s3c2410_pm_syscore_ops is not defined. Same error should happen also
in s3c2410.c and s3c2442.c
Signed-off-by: Domenico Andreoli <cavokz@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Offsets of the irq controller registers were calculated
correctly only for first GPIO bank. This patch fixes
calculation of the register offsets for all GPIO banks.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rather than clipping the number of CPUs using the compile-time NR_CPUS
constant, use the runtime nr_cpu_ids value instead. This allows the
nr_cpus command line option to work as expected.
Cc: <stable@kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Upon adding new board LL debug support, if the resultant code
addition would not cause PC relative offset of "hexbuf" from
"adr r2, hexbuf" (+2) instruction to be representable in a
shifted 8-bit value (hence indirectly putting higher aligment
requirement on larger offsets), following error occurs,
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:138: Error: invalid constant (428) after fixup
Fix it by bringing "hexbuf" closer so that "adr"
can have the offset.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add vision_ep9307, rwi_ews, usb_a9g20, karo, apf9328, tx37, tx25,
tx51, mx51_m2id, pca101, gplugd, smdk4212 and smdk4412.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a private iommu pointer to the ARM-specific arch data in the
device struct, which will be used to attach iommu-specific data
to devices which require iommu support.
Different iommu implementations (on different platforms) will attach
different types of data to this pointer, so 'void *' is currently used
(the downside is reduced typesafety).
Note: ia64, x86 and sparc have this exact iommu extension as well, and
if others are likely to adopt it too, we might want to consider
adding this to the device struct itself directly.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 64bit division functions never had unwinding annotations
added. This prevents a backtrace from being printed within
the function and if a division by 0 occurs. Add the annotations.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of this complaint from dash:
AS arch/arm/boot/compressed/lib1funcs.o
/bin/sh: 1: [: y: unexpected operator
LD arch/arm/boot/compressed/vmlinux
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This resolves the following sparse warning from readl() and other macros,
which ends up embedding readl_relaxed() using the same variable.
arch/arm/mach-tegra/dma.c:169:8: warning: symbol '__v' shadows an earlier one
arch/arm/mach-tegra/dma.c:169:8: originally declared here
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This exposes the PB1176 ROM if you compile in the MTD physmap
mapping and also the map_rom chiptype.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This copy really don't need to do at the very second before the kernel
would crash.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Cache Type Register L1Ip field identifies I-caches with a PIPT
policy using the encoding 11b.
This patch extends the cache policy parsing to identify PIPT I-caches
correctly and prevent them from being treated as VIPT aliasing in cases
where they are sufficiently large.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the mdesc pointer in the fixup function call. No one uses
the mdesc pointer, it shouldn't be modified anyway, and we can't wrap
it, so let's remove it.
Platform files found by:
$ regexp=$(git grep -h '\.fixup.*=' arch/arm |
sed 's!.*= *\([^,]*\),* *!\1!' | sort -u |
tr '\n' '|' | sed 's,|$,,;s,|,\\|,g')
$ git grep $regexp arch/arm
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM uses its own BUG() handler which makes its output slightly different
from other archtectures.
One of the problems is that the ARM implementation doesn't report the function
with the BUG() in it, but always reports the PC being in __bug(). The generic
implementation doesn't have this problem.
Currently we get something like:
kernel BUG at fs/proc/breakme.c:35!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at __bug+0x20/0x2c
With this patch it displays:
kernel BUG at fs/proc/breakme.c:35!
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP
...
PC is at write_breakme+0xd0/0x1b4
This implementation uses an undefined instruction to implement BUG, and sets up
a bug table containing the relevant information. Many versions of gcc do not
support %c properly for ARM (inserting a # when they shouldn't) so we work
around this using distasteful macro magic.
v1: Initial version to replace existing ARM BUG() implementation with something
more similar to other architectures.
v2: Add Thumb support, remove backtrace whitespace output changes. Change to
use macros instead of requiring the asm %d flag to work (thanks to
Dave Martin <dave.martin@linaro.org>)
v3: Remove old BUG() implementation in favor of this one.
Remove the Backtrace: message (will submit this separately).
Use ARM_EXIT_KEEP() so that some architectures can dump exit text at link time
thanks to Stephen Boyd <sboyd@codeaurora.org> (although since we always
define GENERIC_BUG this might be academic.)
Rebase to linux-2.6.git master.
v4: Allow BUGS in modules (these were not reported correctly in v3)
(thanks to Stephen Boyd <sboyd@codeaurora.org> for suggesting that.)
Remove __bug() as this is no longer needed.
v5: Add %progbits as the section flags.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the Integrator defconfig with some sensible defaults:
- Compile a combined image supporting Integrator/AP and
Integrator/CP, with the core modules CM720, CM920, CM922,
CM926, CM1020, CM1022 and CM1026 in a single image, this
works just fine and gives some nice compilation coverage
- NOHZ (tickless) and HRTIMERS turned on
- Compile using EABI, let's assume recent compilers are used
now (tested using GCC 4.4.1)
- Remove forced 32MiB at command line, the bootloader usually
knows this better, and my U-Boot patches nowadays make that
boot loader pass the correct adjusted value
- Enable the MTD Physmap flash driver, so that the changes done
earlier by Marc Zyngier replacing integrator-flash takes
effect
- Enable the PL030 RTC driver that has not been default-compiled
with any config for a while
This has been tested on the real hardware Integrator AP with
both an ARM920T and ARM926EJ-S core module.
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We already have a clock definition for the 24MHz clock in
the Integrator, use that instead of some unclear defines
from the platform.h header. Also delete the senseless
comment that the file shouldn't be edited, I just edited it
and the world didn't come to an end, so it's obviously
false. If anyone still has the mentioned ".s file" and the
s2h awk script generating that header, raise your hand
(and give me your files).
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Drop mult, shift and delta calculations and let the
clockevent core scale this as appropriate.
Set the minimum interval to 1 rather than 15 (0xf), there
is nothing in the data sheets I have indicating that 15
should be some minimum value.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Integrator AP timer has no problem supporting oneshot
ticks with proper code, so let's do it so we can have
NOHZ configured in for this platform too.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These macros are not used by anything since the switch to
generic time in commit b9cedda230
so let's retire them.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per request of rmk, the options should be sorted alphabetically.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the legacy ARM LED code for simpad devices and
register a stadard LED platform device using GPIO line
instead.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register keyboard, polled keyboard and I2C platform
devices based on GPIOs.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- prepend CS3 accessors by simpad_ to indicate they
are specific to simpad devices.
- use spinlock to protect shadow register.
- implement 8 read-only pins.
- use readl/writel macros so barriers are used where
necessary.
- register CS3 as GPIO controller with 24 pins
(16 output only and 8 input only).
- fix PCMCIA driver to access the read-only pins
rather than the shadow register for status bits.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ucb1x00 GPIO definitions to simpad.h and add gpio_base
to ucb1x00 platform device so the pins are available using
the GPIO API.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, show_regs calls __backtrace which does
nothing if CONFIG_FRAME_POINTER is not set. Switch to
dump_stack which handles both CONFIG_FRAME_POINTER and
CONFIG_ARM_UNWIND correctly.
__backtrace is now superseded by dump_stack in general
and show_regs was the last caller so remove __backtrace
as well.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current Versatile Express CPU hotplug code includes a hardcoded WFI
instruction, in ARM encoding. When the kernel is compiled in Thumb-2
mode, this is invalid and causes the machine to hang hard when a CPU
is offlined.
Using the wfi macro (which uses the appropriate assembler mnemonic)
causes the correct instruction to be emitted in either case. As a
consequence of this change, an apparently vestigial "cc" clobber is
dropped from the asm (the macro uses "memory" only).
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When v6 and >=v7 boards are supported in the same kernel, the
__und_usr code currently makes a build-time assumption that Thumb-2
instructions occurring in userspace don't need to be supported.
Strictly speaking this is incorrect.
This patch fixes the above case by doing a run-time check on the
CPU architecture in these cases. This only affects kernels which
support v6 and >=v7 CPUs together: plain v6 and plain v7 kernels
are unaffected.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When testing whether a Thumb-2 instruction is 32 bits long or not,
the masking done in order to test bits 11-15 of the first
instruction halfword won't affect the result of the comparison, so
remove it.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU architecture really should not be changing at runtime, so
make it a global variable instead of a function.
The cpu_architecture() function declared in <asm/system.h> remains
the correct way to read this variable from C code.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
uImages need a load address specified. This makes them
incompatible with multiple zreladdrs. Catch this error
before building an uImage so that we do not end up with
broken uImages. The load address can still be specified
with LOADADDR= on the command line.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without CONFIG_AUTO_ZRELADDR being set the kernel needs a single
zreladdr for building zImages. Bail out if we detect multiple
zreladdrs without CONFIG_AUTO_ZRELADDR.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With d8ecc5c (kbuild: asm-generic support, 2011-04-27) we can
remove a handful of asm-generic wrappers in ARM code. Since the
generic version of sizes.h doesn't contain SZ_48M, we replace
the 4 users of SZ_48M with the equivalent SZ_32M + SZ_16M.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
we save the l2x0 registers at the first initialization, and platform codes
can get them to restore l2x0 status after wakeup.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
this patch fixes the error in Rob Herring's
ARM: 7009/1: l2x0: Add OF based initialization
http://www.spinics.net/lists/arm-kernel/msg131123.html
it has been in rmk/for-next with commit 41c86ff5b
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
using cpu_relax in busy loops is a well-known idiom in the kernel.
It's more for documentation purposes than technically needed here.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds probing for ARM L2x0 cache controllers via device tree. Support
includes the L210, L220, and PL310 controllers. The binding allows setting
up cache RAM latencies and filter addresses (PL310 only).
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defaulting to DEBUG_ICEDCC will cause systems to hang during boot unless
a hardware debugger is listening to the debug comms. channel.
This patch adds a dummy UART option as the default DEBUG_LL choice which
requires the platform to do the right thing.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DEBUG_ICEDCC support is just another DEBUG_LL choice and
selecting it along with other DEBUG_LL options doesn't make
much sense. Put it into the DEBUG_LL choice to avoid confusion.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM patch 7072/1 (debug: use kconfig choice for selecting
DEBUG_LL UART) didn't notice that the Kconfigs relied on being
unselected to configure a different serial port. Since there is
no NONE option in a choice menu, explicitly add the other option
so that both serial ports can be selected.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabled DEBUG_LL hardcodes the UART address into the kernel and results
in a non-portable kernel image. Since this option is only intended for
use when debugging early boot failures, supporting multiple platforms
in such a configuration is not the intended use-case.
This patch documents this limitation in the DEBUG_LL Kconfig help text,
so that users are aware of the portability restrictions that are associated
with enabling low-level debugging support.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabling CONFIG_DEBUG_LL (which is required for earlyprintk) hardwires
the debug UART address into the kernel, so that we can print before the
platform is initialised.
If the user inadvertently selects multiple platforms with DEBUG_LL
enabled, the UART address may not be correct and will likely cause the
kernel to hang in the very early stages of boot.
This patch, based on a skeleton from Russell, uses a Kconfig choice for
selecting the DEBUG_LL UART, therefore allowing the user to make a
choice about the supported platform when DEBUG_LL is enabled.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
