While a set of chunks is being merged, any overlapping writes need to be
queued.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Merging is started when origin is resumed and it is stopped when
origin is suspended or when the merging snapshot is destroyed or
errors are detected.
Merging is not yet interlocked with writes: this will be handled in
subsequent patches.
The code relies on callbacks from a private kcopyd thread.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Merging more than one snapshot is not supported, so prevent
this happening.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Sets num_flush_requests=2 to support flushing both the origin and cow
devices used by the snapshot-merge target.
Also, snapshot_ctr() now gets the origin device using FMODE_WRITE if the
target is snapshot-merge (which writes to the origin device).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The snapshot-merge target should not allocate new exceptions because the
intent is to merge all of its exceptions as quickly and safely as
possible.
This patch introduces the snapshot-merge mapping function and updates
__origin_write() so that it doesn't allocate exceptions on any snapshots
that are being merged.
If a write request to a merging snapshot device is to be dispatched
directly to the origin (because the chunk is not remapped or was already
merged), snapshot_merge_map() must make exceptions in other snapshots so
calls do_origin().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
To track the completion of exceptions relating to the same location on
the device, the current code selects one exception as primary_pe, links
the other exceptions to it and uses reference counting to wait until all
the reallocations are complete.
It is considered too complicated to extend this code to handle the new
snapshot-merge target, where sets of non-overlapping chunks would also
need to become linked.
Instead, a simpler (but less efficient) approach is taken. Bios are
linked to one exception. When it completes, bios are simply retried,
and if other related exceptions are still outstanding, they'll get
queued again to wait for another one.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The snapshot-merge target allows a snapshot to be merged back into the
snapshot's origin device.
One anticipated use of snapshot merging is the rollback of filesystems
to back out problematic system upgrades.
This patch adds snapshot-merge target management to both
dm_snapshot_init() and dm_snapshot_exit(). As an initial place-holder,
snapshot-merge is identical to the snapshot target. Documentation is
provided.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add functions that decide how many consecutive chunks of snapshot to
merge back into the origin next and to update the metadata afterwards.
prepare_merge provides a pointer to the most recent still-to-be-merged
chunk and returns how many previous ones are consecutive and can be
processed together.
commit_merge removes the nr_merged most-recent chunks permanently from
the exception store. The number must not exceed that returned by
prepare_merge.
Introduce NUM_SNAPSHOT_HDR_CHUNKS to show where the snapshot header
chunk is accounted for.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move the __chunk_is_tracked() loop into a separate function as we will
also need to call it from the write path in the rare case of conflicting
writes to the same chunk.
Originally introduced in commit a8d41b59f3
("dm snapshot: fix race during exception creation").
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
To support the merging of snapshots back into their origin we need
to trigger exceptions in other snapshots not being merged without
any incoming bio on the origin device. The bio parameter to
__origin_write() becomes optional and the sector needs supplying
separately.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch rejects messages that can generate I/O while the device
itself is suspended.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the exported dm_suspended() function so that targets
can check whether or not they are suspended.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch renames dm_suspended() to dm_suspended_md() and
keeps it internal to dm.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch moves DMF_SUSPENDED flag set before postsuspend.
No one should care about the ordering, because the flag set and
the postsuspend are protected by a single lock, md->suspend_lock,
and all strict flag-checkers take the lock.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The default plain IV is 32-bit only.
This plain64 IV provides a compatible mode for encrypted devices bigger
than 4TB.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Permit in-use snapshot exception data to be 'handed over' from one
snapshot instance to another. This is a pre-requisite for patches
that allow the changes made in a snapshot device to be merged back into
its origin device and also allows device resizing.
The basic call sequence is:
dmsetup load new_snapshot (referencing the existing in-use cow device)
- the ctr code detects that the cow is already in use and allows the
two snapshot target instances to be linked together
dmsetup suspend original_snapshot
dmsetup resume new_snapshot
- the new_snapshot becomes live, and if anything now tries to access
the original one it will receive -EIO
dmsetup remove original_snapshot
(There can only be two snapshot targets referencing the same cow device
simultaneously.)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When swapping a new table into place, retain the old table until
its replacement is in place.
An old check for an empty table is removed because this is enforced
in populate_table().
__unbind() becomes redundant when followed by __bind().
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When replacing a mapped device's table during a 'resume', delay the
destruction of the old table until the new one is successfully in place.
This will make it easier for a later patch to transfer internal state
information from the old table to the new one (something we do not currently
support) while giving us more options for reversion if a later part
of the operation fails.
Devices are always in the suspended state during dm_swap_table().
This patch reinforces the requirement that all I/O must have been
flushed from the table targets while in this state (including any in
workqueues). In the case of 'noflush' suspending, unprocessed
I/O should have been 'pushed back' to the dm core prior to this point,
for resubmission after the new table is in place.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add the flag DM_QUERY_INACTIVE_TABLE_FLAG to the ioctls to return
infomation about the loaded-but-not-yet-active table instead of the live
table. Prior to this patch it was impossible to obtain this information
until the device had been 'resumed'.
Userspace dmsetup and libdevmapper support the flag as of version 1.02.40.
e.g. dmsetup info --inactive vg1-lv1
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Accept empty barriers in dm-io.
dm-io will process empty write barrier requests just like the other
read/write requests.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reject messages that can generate I/O while the device itself
is suspended.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a mutex to allow possible creators of new work to synchronize with
flushing work queues.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Once we begin deleting a device, prevent any further messages being sent
to targets of its table (to avoid races).
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add dm_deleting_md to check whether or not a given mapped
device is currently being deleted.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch stops the remaining dm-mpath activity during the suspend
sequence by flushing workqueues in postsuspend function.
The current dm-mpath target may not be quiet even after suspend completes
because some workqueues (e.g. device_handler's work, event handling)
are not flushed during the suspend sequence, even though suspended
devices/targets are supposed to be quiet in this state.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds barrier support for request-based dm.
CORE DESIGN
The design is basically same as bio-based dm, which emulates barrier
by mapping empty barrier bios before/after a barrier I/O.
But request-based dm has been using struct request_queue for I/O
queueing, so the block-layer's barrier mechanism can be used.
o Summary of the block-layer's behavior (which is depended by dm-core)
Request-based dm uses QUEUE_ORDERED_DRAIN_FLUSH ordered mode for
I/O barrier. It means that when an I/O requiring barrier is found
in the request_queue, the block-layer makes pre-flush request and
post-flush request just before and just after the I/O respectively.
After the ordered sequence starts, the block-layer waits for all
in-flight I/Os to complete, then gives drivers the pre-flush request,
the barrier I/O and the post-flush request one by one.
It means that the request_queue is stopped automatically by
the block-layer until drivers complete each sequence.
o dm-core
For the barrier I/O, treats it as a normal I/O, so no additional
code is needed.
For the pre/post-flush request, flushes caches by the followings:
1. Make the number of empty barrier requests required by target's
num_flush_requests, and map them (dm_rq_barrier()).
2. Waits for the mapped barriers to complete (dm_rq_barrier()).
If error has occurred, save the error value to md->barrier_error
(dm_end_request()).
(*) Basically, the first reported error is taken.
But -EOPNOTSUPP supersedes any error and DM_ENDIO_REQUEUE
follows.
3. Requeue the pre/post-flush request if the error value is
DM_ENDIO_REQUEUE. Otherwise, completes with the error value
(dm_rq_barrier_work()).
The pre/post-flush work above is done in the kernel thread (kdmflush)
context, since memory allocation which might sleep is needed in
dm_rq_barrier() but sleep is not allowed in dm_request_fn(), which is
an irq-disabled context.
Also, clones of the pre/post-flush request share an original, so
such clones can't be completed using the softirq context.
Instead, complete them in the context of underlying device drivers.
It should be safe since there is no I/O dispatching during
the completion of such clones.
For suspend, the workqueue of kdmflush needs to be flushed after
the request_queue has been stopped. Otherwise, the next flush work
can be kicked even after the suspend completes.
TARGET INTERFACE
No new interface is added.
Just use the existing num_flush_requests in struct target_type
as same as bio-based dm.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch moves dm_end_request() to make the next patch more readable.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch factors out the clone completion code, dm_done(),
from dm_softirq_done() in preparation for a subsequent patch.
No functional change.
dm_done() will be used in barrier completion, which can't use and
doesn't need softirq. The softirq_done callback needs to get a clone
from an original request but it can't in the case of barrier, where
an original request is shared by multiple clones. On the other hand,
the completion of barrier clones doesn't involve re-submitting requests,
which was the primary reason of the need for softirq.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes the counter for the number of in_flight I/Os
to md->pending from q->in_flight in preparation for a later patch.
No functional change.
Request-based dm used q->in_flight to count the number of in-flight
clones assuming the counter is always incremented for an in-flight
original request and original:clone is 1:1 relationship.
However, it this no longer true for barrier requests.
So use md->pending to count the number of in-flight clones.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The semantics of bio-based dm were changed recently in the case of
suspend with "--nolockfs" but without "--noflush".
Before 2.6.30, I/Os submitted before the suspend invocation were always
flushed. From 2.6.30 onwards, I/Os submitted before the suspend
invocation might not be flushed. (For details, see
http://marc.info/?t=123994433400003&r=1&w=2)
This patch brings the behaviour of request-based dm into line with
bio-based dm, simplifying the code and preparing for a subsequent patch
that will wait for all in_flight I/Os to complete without stopping
request_queue and use dm_wait_for_completion() for it.
This change in semantics simplifies the suspend code as follows:
o Suspend is implemented as stopping request_queue
in request-based dm, and all I/Os are queued in the request_queue
even after suspend is invoked.
o In the old semantics, we had to track whether I/Os were
queued before or after the suspend invocation, so a special
barrier-like request called 'suspend marker' was introduced.
o With the new semantics, we don't need to flush any I/O
so we can remove the marker and the code related to the marker
handling and I/O flushing.
After removing this codes, the suspend sequence is now:
1. Flush all I/Os by lock_fs() if needed.
2. Stop dispatching any I/O by stopping the request_queue.
3. Wait for all in-flight I/Os to be completed or requeued.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch factors out the request cloning code in dm_prep_fn()
as clone_rq(). No functional change.
This patch is a preparation for a later patch in this series which needs to
make clones from an original barrier request.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the gfp_mask argument to alloc_rq_tio().
No functional change.
This patch is a preparation for a later patch in this series which needs to
allocate tio (for barrier I/O) with different allocation flag (GFP_NOIO) from
the one in the normal I/O code path.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes the argument of map_request() to clone request
from original request. No functional change.
This patch is a preparation for PATCH 9, which needs to use
map_request() for clones sharing an original barrier request.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds md_in_flight() to get the number of in_flight I/Os.
No functional change.
This patch is a preparation for a later patch in this series, which
changes I/O counter to md->pending from q->in_flight in request-based dm.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-kcopyd: accept zero-size jobs
This patch changes dm-kcopyd so that it accepts zero-size jobs and completes
them immediatelly via its completion thread.
It is needed for multisnapshots snapshot resizing. When we are writing to
a chunk beyond origin end, no copying is done. To simplify the code, we submit
an empty request to kcopyd and let kcopyd complete it. If we didn't submit
a request to kcopyd and called the completion routine immediatelly, it would
violate the principle that completion is called only from one thread and
it would need additional locking.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Keep track of whether or not the device is suspended within the snapshot
target module, the same as we do in dm-raid1.
We will use this later to enforce the correct sequence of ioctls to
transfer the in-core exceptions from a snapshot target instance in
one table to a replacement one capable of merging them back
into the origin.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Store the reference to the snapshot cow device in the core snapshot
code instead of each exception store. It can be accessed through the
new function dm_snap_cow(). Exception stores should each now maintain a
reference to their parent snapshot struct.
This is cleaner and makes part of the forthcoming snapshot merge code simpler.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Add number of sectors used by metadata to the end of the snapshot's status
line.
Renamed dm_exception_store_type's 'fraction_full' to 'usage'. Renamed
arguments to be clearer about what is being returned. Also added
'metadata_sectors'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename exception functions. Preparing to pull them out of
dm-snap.c for broader use.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename exception_table for broader use outside dm-snap.c
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The exception structure is not necessarily just a snapshot
element (especially after we pull it out of dm-snap.c).
Renaming appropriately.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Consolidate the insert_*exception functions. 'insert_completed_exception'
already contains all the logic to handle 'insert_exception' (via
check for a hash_shift of 0), so remove redundant function.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The origin needs to find minimum chunksize of all snapshots. This logic is
moved to a separate function because it will be used at another place in
the snapshot merge patches.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Removed unnecessary 'and' masking: The right shift discards the lower
bits so there is no need to clear them.
(A later patch needs this change to support a 32-bit chunk_mask.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Minor code touch-up. We don't need the 'else'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
strlcpy() will always null terminate the string.
The code should already guarantee this as the last bytes are already
NULs and the string lengths were restricted before being stored in
hc. Removing the '-1' becomes necessary so strlcpy() doesn't
lose the last character of a maximum-length string.
- agk
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Hold all write bios when leg fails and errors are handled
When using a userspace daemon such as dmeventd to handle errors, we must
delay completing bios until it has done its job.
This patch prevents the following race:
- primary leg fails
- write "1" fail, the write is held, secondary leg is set default
- write "2" goes straight to the secondary leg
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Hold all write bios when errors are handled.
Previously the failures list was used only when handling errors with
a userspace daemon such as dmeventd. Now, it is always used for all bios.
The regions where some writes failed must be marked as nosync. This can only
be done in process context (i.e. in raid1 workqueue), not in the
write_callback function.
Previously the write would succeed if writing to at least one leg
succeeded. This is wrong because data from the failed leg may be
replicated to the correct leg. Now, if using a userspace daemon, the
write with some failures will be held until the daemon has done its job
and reconfigured the array. If not using a daemon, the write still
succeeds if at least one leg succeeds. This is bad, but it is consistent
with current behavior.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move bio completion out of dm_rh_mark_nosync in preparation for the
next patch.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move the logic to get a valid mirror leg into a function for re-use
in a later patch.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use the hold framework in do_failures.
This patch doesn't change the bio processing logic, it just simplifies
failure handling and avoids periodically polling the failures list.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add framework to delay bios until a suspend and then resubmit them with
either DM_ENDIO_REQUEUE (if the suspend was noflush) or complete them
with -EIO. I/O barrier support will use this.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Report flush errors as 'F' instead of 'D' for log and mirror devices.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement flush callee. It uses dm_io to send zero-size barrier synchronously
and concurrently to all the mirror legs.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Call the flush callback from the log.
If flush failed, we have no alternative but to mark the whole log as dirty.
Also we set the variable flush_failed to prevent any bits ever being marked as
clean again.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce a callback pointer from the log to dm-raid1 layer.
Before some region is set as "in-sync", we need to flush hardware cache on
all the disks. But the log module doesn't have access to the mirror_set
structure. So it will use this callback.
So far the callback is unused, it will be used in further patches.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce "flush failed" variable. When a flush before clearing a bit
in the log fails, we don't know anything about which which regions are
in-sync and which not.
So we need to set all regions as not-in-sync and set the variable
"flush_failed" to prevent setting the in-sync bit in the future.
A target reload is the only way to get out of this situation.
The variable will be set in following patches.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce flush_header and use it to flush the log device.
Note that we don't have to flush if all the regions transition
from "dirty" to "clean" state.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split the variable "touched" into two, "touched_dirtied" and
"touched_cleaned", set when some region was dirtied or cleaned.
This will be used to optimize flushes.
After a transition from "dirty" to "clean" state we don't have flush hardware
cache on the log device. After a transition from "clean" to "dirty" the cache
must be flushed.
Before a transition from "clean" to "dirty" state we don't have to flush all
the raid legs. Before a transition from "dirty" to "clean" we must flush all
the legs to make sure that they are really in sync.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Flush support for dm-raid1.
When it receives an empty barrier, submit it to all the devices via dm-io.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the hack where we allocate an extra bi_io_vec to store additional
private data. This hack prevents us from supporting barriers in
dm-raid1 without first making another little block layer change.
Instead of doing that, this patch eliminates the bi_io_vec abuse by
storing the region number directly in the low bits of bi_private.
We need to store two things for each bio, the pointer to the main io
structure and, if parallel writes were requested, an index indicating
which of these writes this bio belongs to. There can be at most
BITS_PER_LONG regions - 32 or 64.
The index (region number) was stored in the last (hidden) bio vector and
the pointer to struct io was stored in bi_private.
This patch now aligns "struct io" on BITS_PER_LONG bytes and stores the
region number in the low BITS_PER_LONG bits of bi_private.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allocate "struct io" from a slab.
This patch changes dm-io, so that "struct io" is allocated from a slab cache.
It used to be allocated with kmalloc. Allocating from a slab will be needed
for the next patch, because it requires a special alignment of "struct io"
and kmalloc cannot meet this alignment.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The "wipe key" message is used to wipe the volume key from memory
temporarily, for example when suspending to RAM.
But the initialisation vector in ESSIV mode is calculated from the
hashed volume key, so the wipe message should wipe this IV key too and
reinitialise it when the volume key is reinstated.
This patch adds an IV wipe method called from a wipe message callback.
ESSIV is then reinitialised using the init function added by the
last patch.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch separates the construction of IV from its initialisation.
(For ESSIV it is a hash calculation based on volume key.)
Constructor code now preallocates hash tfm and salt array
and saves it in a private IV structure.
The next patch requires this to reinitialise the wiped IV
without reallocating memory when resuming a suspended device.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use kzfree for salt deallocation because it is derived from the volume
key. Use a common error path in ESSIV constructor.
Required by a later patch which fixes the way key material is wiped
from memory.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Define private structures for IV so it's easy to add further attributes
in a following patch which fixes the way key material is wiped from
memory. Also move ESSIV destructor and remove unnecessary 'status'
operation.
There are no functional changes in this patch.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The "wipe key" message is used to wipe a volume key from memory
temporarily, for example when suspending to RAM.
There are two instances of the key in memory (inside crypto tfm)
but only one got wiped. This patch wipes them both.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Under some special conditions the snapshot hash_size is calculated as zero.
This patch instead sets a minimum value of 64, the same as for the
pending exception table.
rounddown_pow_of_two(0) is an undefined operation (it expands to shift
by -1). init_exception_table with an argument of 0 would fail with -ENOMEM.
The way to trigger the problem is to create a snapshot with a chunk size
that is larger than the origin device.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Take snapshot lock only for STATUSTYPE_INFO, not STATUSTYPE_TABLE.
Commit 4c6fff445d
(dm-snapshot-lock-snapshot-while-supplying-status.patch)
introduced this use of the lock, but userspace applications using
libdevmapper have been found to request STATUSTYPE_TABLE while the device
is suspended and the lock is already held, leading to deadlock. Since
the lock is not necessary in this case, don't try to take it.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch just removes an unnecessary warning:
kobject: 'dm': does not have a release() function,
it is broken and must be fixed.
The kobject is embedded in mapped device struct, so
code does not need to release memory explicitly here.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Error handling code following a kmalloc should free the allocated data.
Cc: stable@kernel.org
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a reported deadlock if there are still unprocessed multipath events
on a device that is being removed.
_hash_lock is held during dev_remove while trying to send the
outstanding events. Sending the events requests the _hash_lock
again in dm_copy_name_and_uuid.
This patch introduces a separate lock around regions that modify the
link to the hash table (dm_set_mdptr) or the name or uuid so that
dm_copy_name_and_uuid no longer needs _hash_lock.
Additionally, dm_copy_name_and_uuid can only be called if md exists
so we can drop the dm_get() and dm_put() which can lead to a BUG()
while md is being freed.
The deadlock:
#0 [ffff8106298dfb48] schedule at ffffffff80063035
#1 [ffff8106298dfc20] __down_read at ffffffff8006475d
#2 [ffff8106298dfc60] dm_copy_name_and_uuid at ffffffff8824f740
#3 [ffff8106298dfc90] dm_send_uevents at ffffffff88252685
#4 [ffff8106298dfcd0] event_callback at ffffffff8824c678
#5 [ffff8106298dfd00] dm_table_event at ffffffff8824dd01
#6 [ffff8106298dfd10] __hash_remove at ffffffff882507ad
#7 [ffff8106298dfd30] dev_remove at ffffffff88250865
#8 [ffff8106298dfd60] ctl_ioctl at ffffffff88250d80
#9 [ffff8106298dfee0] do_ioctl at ffffffff800418c4
#10 [ffff8106298dff00] vfs_ioctl at ffffffff8002fab9
#11 [ffff8106298dff40] sys_ioctl at ffffffff8004bdaf
#12 [ffff8106298dff80] tracesys at ffffffff8005d28d (via system_call)
Cc: stable@kernel.org
Reported-by: guy keren <choo@actcom.co.il>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
Make scsi_dh_activate() function asynchronous, by taking in two additional
parameters, one is the callback function and the other is the data to call
the callback function with.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
commit 4706b349f was a forward port of a fix that was needed
for SLES10. But in fact it is not needed in mainline because
the earlier commit dd00a99e7a fixes the same problem in a
better way.
Further, this commit introduces a bug in the way it interacts with
the automatic read-error-correction. If, after a read error is
successfully corrected, the same disk is chosen to re-read - the
re-read won't be attempted but an error will be returned instead.
After reverting that commit, there is the possibility that a
read error on a read-only array (where read errors cannot
be corrected as that requires a write) will repeatedly read the same
device and continue to get an error.
So in the "Array is readonly" case, fail the drive immediately on
a read error.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
For consistency drop & in front of every proc_handler. Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Resolve the conflict between v2.6.32-rc7 where dn_def_dev_handler
gets a small bug fix and the sysctl tree where I am removing all
sysctl strategy routines.
Normally is it not safe to allow a raid5 that is both dirty and
degraded to be assembled without explicit request from that admin, as
it can cause hidden data corruption.
This is because 'dirty' means that the parity cannot be trusted, and
'degraded' means that the parity needs to be used.
However, if the device that is missing contains only parity, then
there is no issue and assembly can continue.
This particularly applies when a RAID5 is being converted to a RAID6
and there is an unclean shutdown while the conversion is happening.
So check for whether the degraded space only contains parity, and
in that case, allow the assembly.
Signed-off-by: NeilBrown <neilb@suse.de>
When a reshape finds that it can add spare devices into the array,
those devices might already be 'in_sync' if they are beyond the old
size of the array, or they might not if they are within the array.
The first case happens when we change an N-drive RAID5 to an
N+1-drive RAID5.
The second happens when we convert an N-drive RAID5 to an
N+1-drive RAID6.
So set the flag more carefully.
Also, ->recovery_offset is only meaningful when the flag is clear,
so only set it in that case.
This change needs the preceding two to ensure that the non-in_sync
device doesn't get evicted from the array when it is stopped, in the
case where v0.90 metadata is used.
Signed-off-by: NeilBrown <neilb@suse.de>
This is a combination that didn't really make sense before.
However when a reshape is converting e.g. raid5 -> raid6, the extra
device is not fully in-sync, but is certainly active and contains
important data.
So allow that start to be meaningful and in particular get
the 'recovery_offset' value (which is needed for any non-in-sync
active device) from the reshape_position.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that sys_sysctl is a wrapper around /proc/sys all of
the binary sysctl support elsewhere in the tree is
dead code.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Neil Brown <neilb@suse.de>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de> for drivers/char/hpet.c
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Each device has its own 'recovery_offset' showing how far
recovery has progressed on the device.
As the only real significance of this is that fact that it can
be stored in the metadata and recovered at restart, and as
only 1.x metadata can do this, we were only updating
'recovery_offset' to 'curr_resync_completed' when updating
v1.x metadata.
But this is wrong, and we will shortly make limited use of this
field in v0.90 metadata.
So move the update into common code.
Signed-off-by: NeilBrown <neilb@suse.de>
something-bility is spelled as something-blity
so a grep for 'blit' would find these lines
this is so trivial that I didn't split it by subsystem / copy
additional maintainers - all changes are to comments
The only purpose is to get fewer false positives when grepping
around the kernel sources.
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This value is visible through sysfs and is used by mdadm
when it manages a reshape (backing up data that is about to be
rearranged). So it is important that it is always correct.
Current it does not get updated properly when a reshape
starts which can cause problems when assembling an array
that is in the middle of being reshaped.
This is suitable for 2.6.31.y stable kernels.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If a 'sync_max' has been set (via sysfs), it is wrong to clear it
until a resync (or reshape or recovery ...) actually reached that
point.
So if a resync is interrupted (e.g. by device failure),
leave 'resync_max' unchanged.
This is particularly important for 'reshape' operations that do not
change the size of the array. For such operations mdadm needs to
monitor the reshape taking rolling backups of the section being
reshaped. If resync_max gets cleared, the reshape can get ahead of
mdadm and then the backups that mdadm creates are useless.
This is suitable for 2.6.31.y stable kernels.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://neil.brown.name/md:
async_tx: fix asynchronous raid6 recovery for ddf layouts
async_pq: rename scribble page
async_pq: kill a stray dma_map() call and other cleanups
md/raid6: kill a gcc-4.0.1 'uninitialized variable' warning
raid6/async_tx: handle holes in block list in async_syndrome_val
md/async: don't pass a memory pointer as a page pointer.
md: Fix handling of raid5 array which is being reshaped to fewer devices.
md: fix problems with RAID6 calculations for DDF.
md/raid456: downlevel multicore operations to raid_run_ops
md: drivers/md/unroll.pl replaced with awk analog
md: remove clumsy usage of do_sync_mapping_range from bitmap code
md: raid1/raid10: handle allocation errors during array setup.
md/raid5: initialize conf->device_lock earlier
md/raid1/raid10: add a cond_resched
Revert "md: do not progress the resync process if the stripe was blocked"
Allow the snapshot chunk size to be smaller than the page size
The code is now capable of handling this due to some previous
fixes and enhancements.
As the page size varies between computers, prior to this patch,
the chunk size of a snapshot dictated which machines could read it:
Snapshots created on one machine might not be readable on another.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use unsigned integer chunk size.
Maximum chunk size is 512kB, there won't ever be need to use 4GB chunk size,
so the number can be 32-bit. This fixes compiler failure on 32-bit systems
with large block devices.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch locks the snapshot when returning status. It fixes a race
when it could return an invalid number of free chunks if someone
was simultaneously modifying it.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Properly close the device if failing because of an invalid chunk size.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If we are creating snapshot with memory-stored exception store, fail if
the user didn't specify chunk size. Zero chunk size would probably crash
a lot of places in the rest of snapshot code.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Multiple instances of dec_pending() can run concurrently so a lock is
needed when it saves the first error code.
I have never experienced actual problem without locking and just found
this during code inspection while implementing the barrier support
patch for request-based dm.
This patch adds the locking.
I've done compile, boot and basic I/O testings.
Cc: stable@kernel.org
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add missing del_gendisk() to error path when creation of workqueue fails.
Otherwice there is a resource leak and following warning is shown:
WARNING: at fs/sysfs/dir.c:487 sysfs_add_one+0xc5/0x160()
sysfs: cannot create duplicate filename '/devices/virtual/block/dm-0'
Cc: stable@kernel.org
Signed-off-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
