As reported by Sergei, a couple of braces were missing after
the WARN removal patch.
[07/22] OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
https://patchwork.kernel.org/patch/100756/
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: fixed patch description per Anand's E-mail]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Because cgroup_fork() is ran before sched_fork() [ from copy_process() ]
and the child's pid is not yet visible the child is pinned to its
cgroup. Therefore we can silence this warning.
A nicer solution would be moving cgroup_fork() to right after
dup_task_struct() and exclude PF_STARTING from task_subsys_state().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.
This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.
BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable statistics initialization for eth clients that do not support
statistics. This prevents memory corruption on bnx2x hw.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
commit aa2ea0586d (tcp: fix outsegs stat for TSO segments) incorrectly
assumed SNMP_ADD_STATS() was used from BH context.
Fix this using mib[!in_softirq()] instead of mib[0]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some programs like Skype trying to set capture volume automatically.
Normally it will tray, carefully step by step lover or higher, set the volume.
In real word it work not really well, because devises and vendors lie about
real audio settings.
For example most Logitech webcams have 6400 or 3500 steps for capture volume.
They do not tell that actual resolution is 384. So we have only 7 or 18 real
steps. In this patch I set real resolution only for tested devices.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The task_group() function returns a pointer that must be protected
by either RCU, the ->alloc_lock, or the cgroup lock (see the
rcu_dereference_check() in task_subsys_state(), which is invoked by
task_group()). The wake_affine() function currently does none of these,
which means that a concurrent update would be within its rights to free
the structure returned by task_group(). Because wake_affine() uses this
structure only to compute load-balancing heuristics, there is no reason
to acquire either of the two locks.
Therefore, this commit introduces an RCU read-side critical section that
starts before the first call to task_group() and ends after the last use
of the "tg" pointer returned from task_group(). Thanks to Li Zefan for
pointing out the need to extend the RCU read-side critical section from
that proposed by the original patch.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
virtio-pci resets the device at startup by writing to the status
register, but this does not clear the pci config space,
specifically msi enable status which affects register
layout.
This breaks things like kdump when they try to use e.g. virtio-blk.
Fix by forcing msi off at startup. Since pci.c already has
a routine to do this, we export and use it instead of duplicating code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
The non-coherent bulkstat versionsthat look directly at the inode
buffers causes various problems with performance optimizations that
make increased use of just logging inodes. This patch makes bulkstat
always use iget, which should be fast enough for normal use with the
radix-tree based inode cache introduced a while ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
This patch prevents user "foo" from using the SWAPEXT ioctl to swap
a write-only file owned by user "bar" into a file owned by "foo" and
subsequently reading it. It does so by checking that the file
descriptors passed to the ioctl are also opened for reading.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cintiq 21UX2 added 8 more bits for the tool serial number and more
buttons for the expresskey. We did not enable them properly in the
last patch.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some of the recent X86_MRST additions make some "select"s
conditional on X86_MRST but missed some related kconfig symbols,
causing:
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ab2): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ae1): undefined reference to `i8042_unlock_chip'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b40): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b6f): undefined reference to `i8042_lock_chip'
when SERIO_I8042=m, SERIO_LIBPS2=y, KEYBOARD_ATKBD=y.
We need to make i8042 dependant upon !X86_MRST and allow deselecting
atkbd on Moorestown even when !CONFIG_EMBEDDED.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Put the code that is common to both the referral and ordinary mount cases
into a common helper routine.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the attempt to read the calldir fails, then instead of storing the read
bytes, we currently discard them. This leads to a garbage final result when
upon re-entry to the same routine, we read the remaining bytes.
Fixes the regression in bugzilla number 16213. Please see
https://bugzilla.kernel.org/show_bug.cgi?id=16213
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
S_ISDIR(fsinfo.fattr->mode) checks the file type rather than the mode bits,
so we should be checking for the NFS_ATTR_FATTR_TYPE fattr property.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compile warning. kctl should be NULL-initialized.
sound/pci/hda/patch_realtek.c: In function ‘alc_build_controls’:
sound/pci/hda/patch_realtek.c:2550:23: warning: ‘kctl’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous CMT fixup accidentally copied in the TMU shift value, reset
this back to its original value while preserving the TMU fix.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes a race between handle_reply finishing an mds request, signalling
completion, and then dropping the request structing and its dentry+inode
refs, and pre_umount function waiting for requests to finish before
letting the vfs tear down the dcache. If umount was delayed waiting for
mds requests, we could race and BUG in shrink_dcache_for_umount_subtree
because of a slow dput.
This delays umount until the msgr queue flushes, which means handle_reply
will exit and will have dropped the ceph_mds_request struct. I'm assuming
the VFS has already ensured that its calls have all completed and those
request refs have thus been dropped as well (I haven't seen that race, at
least).
Signed-off-by: Sage Weil <sage@newdream.net>
Handle a splice_dentry failure (due to a d_materialize_unique error)
without crashing. (Also, report the error code.)
Signed-off-by: Sage Weil <sage@newdream.net>
It has been reported that the new UFO software fallback path
fails under certain conditions with NFS. I tracked the problem
down to the generation of UFO packets that are smaller than the
MTU. The software fallback path simply discards these packets.
This patch fixes the problem by not generating such packets on
the UFO path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix commit 4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]
Fixed by making mipsnet_probe __devinit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/mipsnet.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
The header file include/linux/tracepoint.h may be included without
include/linux/errno.h and then the compiler will fail on building for
undelcared ENOSYS. This patch fixes this problem via including <linux/errno.h>
to include/linux/tracepoint.h.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
LKML-Reference: <1277118549-622-1-git-send-email-wuzhangjin@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Stanse found that in snd_usb_parse_audio_endpoints, there is a
dangling pointer dereference. When snd_usb_parse_audio_format fails,
fp is freed, and continue invoked. On the next loop, there is
"fp && fp->altsetting == 1 && fp->channels == 1" test, but fp is set
from the last iteration (but is bogus) and thus ilegally dereferenced.
Set fp to NULL before "continue".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
e98ef89b has a typo, causing cfq_blkiocg_update_completion_stats()
to call itself instead of blkiocg_update_completion_stats().
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The function begins and ends with a read_lock. The latter is changed to a
read_unlock.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@locked@
expression E1;
position p;
@@
read_lock(E1@p,...);
@r exists@
expression x <= locked.E1;
expression locked.E1;
expression E2;
identifier lock;
position locked.p,p1,p2;
@@
*lock@p1 (E1@p,...);
... when != E1
when != \(x = E2\|&x\)
*lock@p2 (E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit a2e066bba2 introduced core
swapping for CPU models 64 and later. I recently had a report about
a Sempron 3200+, model 95, for which this patch broke temperature
reading. It happens that this is a single-core processor, so the
effect of the swapping was to read a temperature value for a core
that didn't exist, leading to an incorrect value (-49 degrees C.)
Disabling core swapping on singe-core processors should fix this.
Additional comment from Andreas:
The BKDG says
Thermal Sensor Core Select (ThermSenseCoreSel)-Bit 2. This bit
selects the CPU whose temperature is reported in the CurTemp
field. This bit only applies to dual core processors. For
single core processors CPU0 Thermal Sensor is always selected.
k8temp_probe() correctly detected that SEL_CORE can't be used on single
core CPU. Thus k8temp did never update the temperature values stored
in temp[1][x] and -49 degrees was reported. For single core CPUs we
must use the values read into temp[0][x].
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Rick Moritz <rhavin@gmx.net>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org
i5k_amb.ko uses dynamically allocated memory (by kmalloc) for
attributes passed to sysfs. So, sysfs_attr_init() should be called
for working happy with lockdep.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [2.6.34 only]
Gen3 chips have slightly different flip commands, and also contain a bit
that indicates whether a "flip pending" interrupt means the flip has
been queued or has been completed.
So implement support for the gen3 flip command, and make sure we use the
flip pending interrupt correctly depending on the value of ECOSKPD bit
0.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Hardware will set the flip pending ISR bit as soon as it receives the
flip instruction, and (supposedly) clear it once the flip completes
(e.g. at the next vblank). If we try to send down a flip instruction
while the ISR bit is set, the hardware can become very confused, and we
may never receive the corresponding flip pending interrupt, effectively
hanging the chip.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit c7f486567c
(PCI PM: PCIe PME root port service driver) causes the native PCIe
PME signaling to be used by default, if the BIOS allows the kernel to
control the standard configuration registers of PCIe root ports.
However, the native PCIe PME is coupled to the native PCIe hotplug
and calling pcie_pme_acpi_setup() makes some BIOSes expect that
the native PCIe hotplug will be used as well. That, in turn, causes
problems to appear on systems where the PCIe hotplug driver is not
loaded. The usual symptom, as reported by Jaroslav Kameník and
others, is that the ACPI GPE associated with PCIe hotplug keeps
firing continuously causing kacpid to take substantial percentage
of CPU time.
To work around this issue, change the default so that the native
PCIe PME signaling is only used if directly requested with the help
of the pcie_pme= command line switch.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15924 , which is
a listed regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Jaroslav Kameník <jaroslav@kamenik.cz>
Tested-by: Antoni Grzymala <antekgrzymala@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
