Basic PM support: reinit the core on resume, disable it on suspend.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The standard rtc-m41t80.c driver cannot be used with the SWARM as it is,
because the board does not provide setup information for the I2C core.
As a result the bus and the address to probe for the M41T80 chip is not
known.
Here is a set of changes that fix the problem:
1. swarm-i2c.c -- SWARM I2C board setup, currently for the M41T80 chip on
the bus #1 only (there is a MAX6654 temperature sensor on the bus #0
which may be added in the future if we have a driver for that chip).
2. The i2c-sibyte.c BCM1250A SMBus controller driver now registers its
buses as numbered so that board setup is correctly applied.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the check of pre-transaction and post-transaction conditions to
separate functions, and adjust them a bit. Having dedicated functions
for that ensures that errors are handled in a consistent way.
Bit HOST_BUSY of the status register is read-only, so writing to it is
certainly not going to clear it. If this bit is set then we simply
don't want to start the transaction, as it means that somebody else
(ACPI, SMM?) is already using the controller.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Bit BUS_ERR of the status register means that the ICH host controller
lost the arbitration. Report this event as such.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Dumping the register values before and after every transaction was
useful during driver development but now it's only spamming the log.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Struct members udelay and timeout aren't used anywhere, so drop them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Eric Brower <ebrower@gmail.com>
Initialize the pxa i2c bus during subsystem initialization to make it
available during driver initialization (e.g. display powerup for pxafb).
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enable the IBM I2C driver for all PPC4xx variants by adding
"ibm,iic" to the compatible list. This way all currently available
arch/powerpc 4xx ports can make use of this driver without any changes.
Additionally all "other" compatible entries are removed since they are
not needed anymore.
Currently all 4xx PPC's have the same compatible I2C macro. If at some
time an incompatibility is detected we can take care of this with an
additional property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The deprecated OCP style driver part is used by the "old" arch/ppc
platform. This platform is scheduled for removal in June/July this year.
This patch now removes the OCP driver part from the IBM I2C driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let general purpose I2C/SMBus bus drivers add SPD to their class. Once
this is done, we will be able to tell the eeprom driver to only probe
for SPD EEPROMs and similar on these buses.
Note that I took a conservative approach here, adding I2C_CLASS_SPD to
many drivers that have no idea whether they can host SPD EEPROMs or not.
This is to make sure that the eeprom driver doesn't stop probing buses
where SPD EEPROMs or equivalent live.
So, bus driver maintainers and users should feel free to remove the SPD
class from drivers those buses never have SPD EEPROMs or they don't
want the eeprom driver to bind to them. Likewise, feel free to add the
SPD class to any bus driver I might have missed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Bugfixes to the i2c-cpm driver
- enable correct interrupts (I2CER_TXE instead of I2CER_BUSY)
- replace forgotten iic with i2c
- prefix debug-output on init with 0x and add frequency
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This driver uses the port of 2.4 code from Vitaly Bordug
<vitb@kernel.crashing.org> and the actual algorithm used by the i2c
driver of the DBox code on cvs.tuxboc.org from Felix Domke
(tmbinc@gmx.net) and Gillem (htoa@gmx.net) converted to an
of_platform_driver. Tested on CPM1 (MPC823 on dbox2 hardware) and
CPM2 (MPC8272).
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
New i2c bus driver for the Intel SCH chipsets (AF82US15W, AF82US15L,
AF82UL11L).
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix errorcode to be more descriptive when ioremap fails.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Many PC SMBus host controller drivers don't properly handle the case
where they are requested to achieve a transaction they do not support.
Update them so that the consistently print a warning message and
return a single error value in this case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c-piix4 driver was used recently as a model to write a new SMBus
host controller driver and this made me realize that the code of this
old driver wasn't exactly good. So, here are many cleanups and minor
fixes to this driver, so that these minor mistakes aren't duplicated
again:
* Delete unused structure.
* Delete needless forward function declaration.
* Properly announce the SMBus host controller as we find it.
* Spell it SMBus not SMB.
* Return -EBUSY instead of -ENODEV when the I/O region is already in
use.
* Drop useless masks on the 7-bit address and the R/W bit.
* Reject block transaction requests with an invalid block length.
* Check and report block transaction replies with an invalid block
length.
* Delete a useless comment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM"). Build tested, with eyeball
review.
One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The list of I2C/SMBus bus drivers is growing and it is sometimes
difficult for the users to figure out what drivers they should enable.
By grouping the drivers by type, I hope to make the selection easier.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since only a few Blackfins lack TWI, just list them in a depends
statement.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the scheduled removal of i2c-i810, i2c-prosavage
and i2c-savage4.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Just like the Tyan S4882, the S4985 uses a multiplexer to give access
to all 16 memory module SPD EEPROMs. This specific i2c-nforce2-s4985
driver adds support for this. It is heavily based on the older
i2c-amd756-s4882 driver.
As more mainboards will use multiplexer chips, we will have to find a
way to support them without having to write a new specfic driver for
each. The recent changes to the i2c subsystem should help us, and the
new gpio subsystem might help, too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If an interrupt happens before an I2c master read/write,
complete is called on uninitialized structure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If wait_for_completion_interruptible_timeout exits due
to a signal, the i2c bus was locking up.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Interrupts are enabled at the point where the DAVINCI_I2C_IVR_REG is read,
so unless an interrupt happened just at that moment, no interrupt would be
pending. Even though documentation implies you should do this, I see no
reason. If slave support is added, this read would cause a hard to
reproduce bug.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Previously the dev_dbg only printed if no error.
Printing also on an error is more useful
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ensure psc value gives a clock between 7-12 MHz
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a MODULE_ALIAS() statement for the i2c-s3c2410 controller
to ensure that it can be autoloaded on the S3C2440 systems that
we support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The driver should be returning -ENXIO for transfers that do not
pass the initial address byte stage.
Note, also small tidyups to the driver comments in the area.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We should check for the reception of an ACK after transmitting each
data byte. The address send has been correctly checking this, but the
data write byte state should have also been checking for these failures.
As part of the same fix, we remove the ACK checking from the receive
path where it should not have been checking for an ACK which our hardware
was sending.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The i2c-amd756 driver pretends to support SMBus process call
transactions but actually does not. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a strange chip at 0x2e on the second SMBus channel of the
DFI Lanparty NF4 Expert motherboard. Accessing the chip reboots the
system. As there's nothing interesting on this SMBus channel, the
easiest and safest thing to do is to disable it on that board.
This is a better fix to bug #5889 than the it87 driver update that was
done originally:
http://bugzilla.kernel.org/show_bug.cgi?id=5889
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The Alchemy platform code registers the SMBus device using the virtual
address of its registers instead of the physical one -- fix this, taking
into account that actually the whole megabyte is decoded by any of the
programmable serial controllers (one of which is SMBus), and that all the
Alchemy peripherals are directly mappable into KSEG1 kernel space and
therefore ioremap() call would just boil down to CKSEG1ADDR() invocation.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The i2c_sibyte_add_bus() function is not called, nor meant to, from
outside, so mark it as static; fixing a sparse warning too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The frequency may have been once hardcoded to 100 kHz, but currently it is
passed as an argument to i2c_sibyte_add_bus(), so update the comment to
match code. While at it, reformat a nearby comment for consistency. No
functional changes.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We had a report that running sensors-detect on a Sapphire AM2RD790
motherbord killed the CPU. While the exact cause is still unknown,
I'd rather play it safe and prevent any access to the SMBus on that
machine by not letting the i2c-piix4 driver attach to the SMBus host
device on that machine. Also blacklist a similar board made by DFI.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Per the PIIX4 errata, there maybe a delay between setting the
start bit in the Smbus Host Controller Register and the transaction
actually starting. If the driver doesn't delay long enough, it
may appear that the transaction is complete when actually it
hasn't started, this may lead to bus collisions.
While 1 ms appears to be enough for most chips, the ServerWorks CSB5
wants 2 ms.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Alter the mpc i2c driver to use the NO_IRQ symbol instead of the constant
zero when checking for valid interrupts. NO_IRQ=-1 on ppc and NO_IRQ=0 on
powerpc so the checks against zero are not correct.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
* Remove a needless include.
* Remove a legacy comment in piix4_access.
* Minor optimization in piix4_access.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to the
hotpluggable I2C platform drivers, to allow module auto loading.
[ db: add some more drivers ]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is V5 of the SuperH Mobile I2C Controller Driver. A simple Master
only driver for the I2C block included in processors such as sh7343,
sh7722 and sh7723. Tested on a sh7722 MigoR using a rs5c732b rtc.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Simply use "depends on BLACKFIN" (which is technically correct) and just
document which machines have the device.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
