This patch implements blit support for bo moves using
the 3D engine. It uses the same method as r6xx/r7xx:
- store the base state in an IB
- emit variable state and vertex buffers to do the blit
This allows the hw to move bos using the 3D engine and allows
full use of vram beyond the pci aperture size.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When writeback is enabled, the GPU shadows writes to certain
registers into a buffer in memory. The driver can then read
the values from the shadow rather than reading back from the
register across the bus. Writeback can be disabled by setting
the no_wb module param to 1.
On r6xx/r7xx/evergreen, the following registers are shadowed:
- CP scratch registers
- CP read pointer
- IH write pointer
On r1xx-rr5xx, the following registers are shadowed:
- CP scratch registers
- CP read pointer
v2:
- Combine wb patches for r6xx-evergreen and r1xx-r5xx
- Writeback is disabled on AGP boards since it tends to be
unreliable on AGP using the gart.
- Check radeon_wb_init return values properly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.
Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.
This allows kexec to work on a Power6/RN50 system.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Advanced validation is not implemented yet.
The mesa code that uses this will be released soon.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Separate dynpm and profile based power management methods. You can select the pm method
by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
"default" - default clocks
"auto" - select between low and high based on ac/dc state
"low" - DC, low power mode
"high" - AC, performance mode
The current base profile is "default", but it should switched to "auto" once we've tested
on more systems. Switching the state is a matter of echoing the requested profile to
power_profile in sysfs. The lowest power states are selected automatically when dpms turns
the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment. We can revisit this later once we
have basic pm in.
- Move pm init/fini to modesetting path. pm is tightly coupled with display state. Make sure
display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option. It's now selectable via sysfs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add two new sysfs attributes:
- dynpm
- power_state
Echoing 0/1 to dynpm disables/enables dynamic power management.
The driver scales the sclk dynamically based on the number of
queued fences. dynpm only scales sclk dynamically in single head
mode.
Echoing x.y to power_state selects a static power state (x) and clock
mode (y). This allows you to statically select a power state and clock
mode. Selecting a static clock mode will disable dynpm.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- pm_misc() - handles voltage, pcie lanes, and other non
clock related power mode settings. Currently disabled.
Needs further debugging
- pm_prepare() - disables crtc mem requests right now.
All memory clients need to be disabled when changing
memory clocks. This function can be expanded to include
disabling fb access as well.
- pm_finish() - enable active memory clients.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This also simplifies the code and enables reclocking with multiple heads
active by tracking whether the power states are single or multi-head
capable.
Eventually, we will want to select a power state based on external
factors (AC/DC state, user selection, etc.).
(v2) Update for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check to see if the GUI engine and related blocks
(2D, 3D, CP, etc) are idle or not. There are a number
of cases when we need to know if the drawing engine
is busy.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Gart setup is more or less like r7xx. Copy
rv770d.h to evergreend.h and fix up changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This simplify and improve GPU reset for R1XX-R6XX hw, it's
not 100% reliable here are result:
- R1XX/R2XX works bunch of time in a row, sometimes it
seems it can work indifinitly
- R3XX/R3XX the most unreliable one, sometimes you will be
able to reset few times, sometimes not even once
- R5XX more reliable than previous hw, seems to work most
of the times but once in a while it fails for no obvious
reasons (same status than previous reset just no same
happy ending)
- R6XX/R7XX are lot more reliable with this patch, still
it seems that it can fail after a bunch (reset every
2sec for 3hour bring down the GPU & computer)
This have been tested on various hw, for some odd reasons
i wasn't able to lockup RS480/RS690 (while they use to
love locking up).
Note that on R1XX-R5XX the cursor will disapear after
lockup haven't checked why, switch to console and back
to X will restore cursor.
Next step is to record the bogus command that leaded to
the lockup.
V2 Fix r6xx resume path to avoid reinitializing blit
module, use the gpu_lockup boolean to avoid entering
inifinite waiting loop on fence while reiniting the GPU
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Patch rename gpu_reset to asic_reset in prevision of having
gpu_reset doing more stuff than just basic asic reset.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch cleanup the fence code, it drops the timeout field of
fence as the time to complete each IB is unpredictable and shouldn't
be bound.
The fence cleanup lead to GPU lockup detection improvement, this
patch introduce a callback, allowing to do asic specific test for
lockup detection. In this patch the CP is use as a first indicator
of GPU lockup. If CP doesn't make progress during 1second we assume
we are facing a GPU lockup.
To avoid overhead of testing GPU lockup frequently due to fence
taking time to be signaled we query the lockup callback every
500msec. There is plenty code comment explaining the design & choise
inside the code.
This have been tested mostly on R3XX/R5XX hw, in normal running
destkop (compiz firefox, quake3 running) the lockup callback wasn't
call once (1 hour session). Also tested with forcing GPU lockup and
lockup was reported after the 1s CP activity timeout.
V2 switch to 500ms timeout so GPU lockup get call at least 2 times
in less than 2sec.
V3 store last jiffies in fence struct so on ERESTART, EBUSY we keep
track of how long we already wait for a given fence
V4 make sure we got up to date cp read pointer so we don't have
false positive
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This just an example to show what radeon_asic.h might be good for.
Before Jerome kills it ;)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With these static structs gone, radeon_asic.h is a real header file
and can be used as such.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 asic was missing set_surface_reg callback leading to
oops.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r200 cards have dma engine which can be used to tranfer data
between vram and system memory.
r300 dma engine registers match r200 dma engine. Enabling
dma copy for r200 is simple as hooking r200 asic to already
existing function r300_copy_dma.
Rename r300_dma_copy to r200_dma_copyto reflect that supports
starts from r200 cards.
v2: Created a new asic object for r200 cards.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Setting global asic structure to point to different function
would cause problem in system where is multiple r300 cards
with different bus type.
r300_asic_pcie is just copy from r300_asic with gart tlb
functions replaced with pcie versions.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds initial Evergreen KMS support, it doesn't include
any acceleration features or interrupt handling yet.
Major changes are DCE4 handling for PLLs for the > 2 crtcs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- only r4xx/r5xx/rs6xx/rs740 have clock gating atom table,
so disable it on r6xx. it's already disabled on r7xx
- check to make sure the clock_gating hook exists before
calling it. This avoids a segfault on asics without
that function.
- remove unused static power management function.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It seems that some R6XX/R7XX silently ignore HDP flush when
programmed through ring, this patch addback an ioctl callback
to allow R6XX/R7XX hw to perform such flush through MMIO in
order to fix a regression. For more details see:
http://bugzilla.kernel.org/show_bug.cgi?id=15186
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R300 family will hard lockup if host path read cache flush is
done through MMIO to HOST_PATH_CNTL. But scheduling same flush
through ring seems harmless. This patch remove the hdp_flush
callback and add a flush after each fence emission which means
a flush after each IB schedule. Thus we should have same behavior
without the hard lockup.
Tested on R100,R200,R300,R400,R500,R600,R700 family.
V2: Adjust fence counts in r600_blit_prepare_copy()
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This enables the use of interrupts on r6xx/r7xx hardware.
Interrupts are implemented via a ring buffer. The GPU adds
interrupts vectors to the ring and the host reads them off
in the interrupt handler. The interrupt controller requires
firmware like the CP. This firmware must be installed and
accessble to the firmware loader for interrupts to function.
MSIs don't seem to work on my RS780. They work fine on all
my discrete cards. I'm not sure about other RS780s or
RS880s. I've disabled MSIs on RS780 and RS880, but it would
probably be worth checking on some other systems.
v2 - fix some checkpatch.pl problems;
re-read the disp int status reg if we restart the ih;
v3 - remove the irq handler if r600_irq_init() fails;
remove spinlock in r600_ih_ring_fini();
move ih rb overflow check to r600_get_ih_wptr();
move irq ack to separate function;
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rendercheck under kms on r600s was failing due to HDP flushing not happening.
This adds HDP flushing to the object wait function for r100->r700 families.
rendercheck passes basic tests on r600 with this change.
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (52 commits)
drm/kms: Init the CRTC info fields for modes forced from the command line.
drm/radeon/r600: CS parser updates
drm/radeon/kms: add debugfs for power management for AtomBIOS devices
drm/radeon/kms: initial mode validation support
drm/radeon/kms/atom/dce3: call transmitter init on mode set
drm/radeon/kms: store detailed connector info
drm/radeon/kms/atom/dce3: fix up usPixelClock calculation for Transmitter tables
drm/radeon/kms/r600: fix rs880 support v2
drm/radeon/kms/r700: fix some typos in chip init
drm/radeon/kms: remove some misleading debugging output
drm/radeon/kms: stop putting VRAM at 0 in MC space on r600s.
drm/radeon/kms: disable D1VGA and D2VGA if enabled
drm/radeon/kms: Don't RMW CP_RB_CNTL
drm/radeon/kms: fix coherency issues on AGP cards.
drm/radeon/kms: fix rc410 suspend/resume.
drm/radeon/kms: add quirk for hp dc5750
drm/radeon/kms/atom: fix potential oops in spread spectrum code
drm/kms: typo fix
drm/radeon/kms/atom: Make card_info per device
drm/radeon/kms/atom: Fix DVO support
...
conflict in radeon since new init path merged with vga arb code.
Conflicts:
drivers/gpu/drm/radeon/radeon.h
drivers/gpu/drm/radeon/radeon_asic.h
drivers/gpu/drm/radeon/radeon_device.c
This remove old init path and allow code cleanup, now all hw
use the new init path, see top of radeon.h for description of
this.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. Do a massive RS600 register cleanup to clarify RS600
register, we are still bit fuzy on some register and waiting for
more informations. I don't have hw to test, so this patch is a
best effort to not break anythings and to try to improve things.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also cleanup register specific to RS690/RS740. Version 2 add
missing header file for register, remove unecessary call to AGP
function and fix an indentation bug.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. More cleanup should happen latter to remove even more
callback. Also cleanup register specific to R100,RV200,RV250.
Version 2 correct the placement on IGP of the VRAM inside GPU address
space to match the stollen RAM placement of IGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also cleanup register specific to RS400/RS480. This patch also fix
legacy VGA register used to disable VGA access we were programming
wrong register. Now we should properly disable VGA on r100 up to
rs400 asics. Note that RS400/RS480 resume is broken, it hangs the
computer while reprogramming dynamic clock, doesn't work either
without that patch. We need to spend more time investigating this
issue. Version 2 of the patch remove dead code that was left
commented out in the previous version. Version 3 correct the
placement on IGP of the VRAM inside GPU address space to match the
stollen RAM placement of IGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (25 commits)
drm/radeon/kms: Convert R520 to new init path and associated cleanup
drm/radeon/kms: Convert RV515 to new init path and associated cleanup
drm: fix radeon DRM warnings when !CONFIG_DEBUG_FS
drm: fix drm_fb_helper warning when !CONFIG_MAGIC_SYSRQ
drm/r600: fix memory leak introduced with 64k malloc avoidance fix.
drm/kms: make fb helper work for all drivers.
drm/radeon/r600: fix offset handling in CS parser
drm/radeon/kms/r600: fix forcing pci mode on agp cards
drm/radeon/kms: fix for the extra pages copying.
drm/radeon/kms/r600: add support for vline relocs
drm/radeon/kms: fix some bugs in vline reloc
drm/radeon/kms/r600: clamp vram to aperture size
drm/kms: protect against fb helper not being created.
drm/r600: get values from the passed in IB not the copy.
drm: create gitignore file for radeon
drm/radeon/kms: remove unneeded master create/destroy functions.
drm/kms: start adding command line interface using fb.
fb: change rules for global rules match.
drm/radeon/kms: don't require up to 64k allocations. (v2)
drm/radeon/kms: enable dac load detection by default.
...
Trivial conflicts in drivers/gpu/drm/radeon/radeon_asic.h due to adding
'->vga_set_state' function pointers.
Convert the r520 asic support to new init path, change are smaller than
previous one as most of the architecture is now in place and more code
sharing can happen btw various asics.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Convert the rv515 asic support to new init path also add an explanation
in radeon.h about the new init path. There is also few cleanups
associated with this change (others asic calling rv515 helper
functions).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.
VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.
This patch comes from Fedora rawhide kernel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
GART static one time initialization was mixed up with GART
enabling/disabling which could happen several time for instance
during suspend/resume cycles. This patch splits all GART
handling into 4 differents function. gart_init is for one
time initialization, gart_deinit is called upon module unload
to free resources allocated by gart_init, gart_enable enable
the GART and is intented to be call after first initialization
and at each resume cycle or reset cycle. Finaly gart_disable
stop the GART and is intended to be call at suspend time or
when unloading the module.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This convert r4xx to new init path it also fix few bugs.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the r600 KMS + CS support to the Linux kernel.
The r600 TTM support is quite basic and still needs more
work esp around using interrupts, but the polled fencing
should work okay for now.
Also currently TTM is using memcpy to do VRAM moves,
the code is here to use a 3D blit to do this, but
isn't fully debugged yet.
Authors:
Alex Deucher <alexdeucher@gmail.com>
Dave Airlie <airlied@redhat.com>
Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the command stream checker for the RN50, R100 and R200 cards.
It stops any access to 3D registers on RN50, and does checks
on buffer sizes on the r100/r200 cards. It also fixes some texture
sizing checks on r300.
Signed-off-by: Dave Airlie <airlied@redhat.com>
