Disable host TX rate control. The wl1271 firmware is already managing rate
control, so this eliminate unnecessary host processing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of managing the TX security sequence number as two variables, use
one 64 bit variable. This greatly simplifies the handling of the number.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the required block count calculation. Though it
introduces a division operator, it greatly simplifies the formula.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses a higher precision timer to synchronize with the firmware
clock. Improved precision is needed as on some platforms a jiffy may be up to
tens of milliseconds, and the required precision is closer to TU's.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements looped IRQ handling. In essence, if a new interrupt is
asserted by the FW while the host is processing the previous one, the host
will directly proceed processing the new IRQ without leaving the handling
function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mask firmware interrupts while processing interrupts. This allows the
interrupt handler looping to work efficiently thus reducing interrupt
processing latency.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will ack RX frames read from the firmware in one single write,
instead of acking all the frames separately. This will reduce the amount of
required communication per frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the annoying and dmesg-flooding WLAN PSM entry/exit traces. Instead,
only output them if PSM traces are enabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue stopping/waking functionality was broken in a way that could
cause huge latencies in TX transfers and even cause the TX to stall in the
right circumstances. Correct these problems.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ad-hoc mode preventing mac80211 from properly
detecting other ad-hoc networks with the same SSID.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Fix a TX result overflow problem that was present in the TX path and visible
with at least linksys AP's (probably any AP with high throughput capability.)
- Optimize TX by writing FW trigger for a group of TX frames instead of
each and every frame.
- Slightly optimize the TX path code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most probably patch "wl1271: add most of the normal initialization commands
to PLT mode" enabled the RX path in firmware so that now driver received
frames and passed them to mac80211, which warned about them.
Workaround this by not retrieving frames from the hardware, just ignore them.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed two bugs causing problems when unloding wl1271 module. First was
missing sdio_set_drvdata call from the probe function, second was order
of function calls in the remove function.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed access to fw status register to use raw read instead of
translated addressing. On SDIO access by translated addressing was not
working and raw access is working also on SPI.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added initial implementation of SDIO interfacte to the wl1271 driver.
When selected, this adds new module called "wl1271_sdio".
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Divided wl1271 driver to wl1271 "core" and wl1271_spi modules in preparation
of integration of the SDIO implementation.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed wl1271_spi.h header as there's no more need to access functions
declared there outside of wl1271_spi.c. Also made those SPI access
functions static.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed the driver to use if_ops structure to abstract access to the IO
layer (SPI or SDIO).
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved wl1271 drivers probe, remove etc. functions and structres to
wl1271_spi.c from wl1271_main.c in preparation of implementing SDIO interface.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved allocation and freeing of context structure of the driver to
separate functions from probe and remove functions.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added reset and init functions to IO layer of the driver.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for integration of SDIO implementation renamed some IO
functions from wl1271_spi_* form to wl1271_*.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In prepraration for integration of SDIO implementation moved some IO
functions common for SPI and SDIO to separate file.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testmode will be used to send PLT (Production Line Testing) commands
from user space.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon filter table configuration ACX structure had certain elements
reversed, resulting in firmware instability in regard of the feature. Fix
the structure.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If re-configuring the SSID while ad-hoc was already enabled, the beacon
template would be properly updated, but the SSID passed in the CMD_JOIN would
not - hence filtering etc would not work properly.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WEP key index handling was broken: the default key when using key 0 was never
specified to the FW, and if using other default than 0, it would be set on the
TX path for every single TX'd frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new firmware does not allow removal of unicast keys - they will be
automatically removed on the next CMD_JOIN.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of acking RX packets read from the FW once all (of several possible)
buffered packets are retrieved, ack packets one by one as they are read. This
enables the FW to start receiving more packets from the network while the
host read operation is still ongoing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
elp_wakeup() was missing in op_conf_tx() which caused wakeup problems in
power save. I forgot to add this part when porting the patch from wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If reverting to a random MAC address, the driver would not update it to the
NVS file, and hence the firmware frame filtering would not work properly.
So update the randomized MAC address to the NVS image.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our NVS uploading mechanism had a bug that was causing it to pass three extra
zeros at the start of the NVS. This may be a problem in the NVS generation
application, but for now we fix it in the driver.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to configure PLT mode almost in the same way as normal mode. Most of
the configuration functions need to be called also when entering PLT, with
the exception of a few RX and TX configuration (which cause mac80211 warnings
if enable while runnning PLT tests).
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always randomizing the MAC address, retrieve and configure the
MAC address from the device specific nvs file. For now, randomize an address
only if the address in the NVS is zero.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the hardcoded general and radio parameter configuration in the driver
with configuration taken from the NVS file directly. Also remove the driver
dependency to the structures with the parameter data.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Based on a similar patch from wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For WMM we need to configure each tid separately so modify
wl1271_acx_tid_cfg() to take the configuration from function parameters
instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For WMM we need to configure each queue separately so modify
wl1271_acx_ac_cfg() to take the configuration from function parameters
instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to extract the SSID from the beacon template used for
ad-hoc. The mac80211 currently does not provide the SSID, so this is a
workaround for that, for now.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel changing code would a) change the BSSID to a dummy on upon
channel change, breaking connectivity, and b) not update the channel number
at all for ad-hoc, breaking adhoc.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the PSM entry function assumes successful operation, and enables
ELP, BET and beacon filtering right away. This is bad, because the PSM
entry may fail due to environmental issues, which will cause the ELP, BET and
beacon filtering to be illegally enabled (because FW remains in active state.)
Fix this by enabling ELP, BET and beacon filtering only after successful entry,
and by ensuring the firmware is in active mode after the failure.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 uses unit units of 32 usec with txop but wl1251_acx_ac_cfg()
expects it to be usecs. This fortunately didn't cause any severe problems,
only that firmware was using incorrect WMM settings.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because DTIM information is required for powersave
but is only conveyed in beacons, wait for a beacon
before enabling powersave, and change the way the
information is conveyed to the driver accordingly.
mwl8k doesn't currently seem to implement PS but
requires the DTIM period in a different way; after
talking to Lennert we agreed to just have mwl8k do
the parsing itself in the finalize_join work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are unused and as with a previous patch 5ef5da for wl1251
this removes some other unused flags. the IRQ_MASK specifically
conflicts with include/pcmcia/cs.h when using compat-wireless.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 firmware supports U-APSD just with a simple queue configuration
change so enable it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The qos null data template is needed for U-APSD.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In various cases wl1251_op_bss_info_changed() did not call elp_sleep()
after an error was noticed. Fix it by using correct goto label.
The bug was a theoretical one, in practise it doesn't matter because
if commands start returning errors there will be lots of other problems.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of channels to be used in scan was hard coded in wl1251. The
proper way is to use the channels array provided by mac80211.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of creating the template in driver, get it from mac80211 instead.
Thanks to this, three functions can be now removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current scanning code wasn't following the preferred style. Move code
related to scan and trigger scan to commans to wl1251_cmd.c. Because
there's now less code in wl1251_hw_scan(), the function can be now
merged with wl1251_op_hw_scan().
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that mac80211 creates templates for PS Poll and Nullfunc frames, use
them instead of creating our own.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a timeout bug in
/drivers/net/wireless/wl12xx/wl1271_spi.c
In the current code you cannot tell why you exited
the "poll for data ready" do-while loop if exiting
was done after the last possible loop.
Then timeout==0 regardless of (val & OCP_READY_MASK) or
!(val & OCP_READY_MASK), leading to possible false timeout...
Simple correction could be decreasing timeout after checking
for !(val & OCP_READY_MASK), not before
(Manually converted from email to an actual patch by me. -- JWL)
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a minor bug in the code causing a "join" to be performed before
there is an intention to associate. Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because the interface is started and the vif are created and destroyed
separately, there is a slim possibility beacon-loss indications occur while
there is no vif - causing a kernel-oops unless checked.
Add checking for the vif.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This acx configures host clock parameters in correspondence with the clock
request line - the settling time of the clock, and whether fast wake-up is
supported.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For cleaner implementation, change the bunch of booleans in the struct wl1271
structure into a flags bitmask.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, only basic rates were used for data transmission - resulting in
reduced transfer rates. This patch takes enables the firmware to take advantage
of the full set of data rates supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously a "firmware chooses" value was used for the rates of all control
message templates set to the firmware. This resulted in a too high rate to be
chosen to transmit those messages. Change this by configuring a fixed low rate
for the templates.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds rudimentary a-hoc support for the driver. It will allow
setting up ad-hoc, and for other devices to scan and join. The beacon and probe
response template setting is slightly dirty, and need to be properly
implemented with support from mac80211. Also, the SSID is not configured to the
firmware - the FW will not be able to respond to probe requests autonomously.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the beacon-loss indication to stack from PSM entry failure handling -
this will cause more problems than it will solve due to the design of the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a short delay before powering on the wl1271. Normally, it is
not needed, but if the wl1271 has been powered off shortly before, for reliable
firmware-booting this small stabilization delay is required.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 has a hardware bug which causes it to randomly (very infrequently)
to fail powering up properly. This patch implements retry for the chipset boot
sequence, to work around the hardware problem.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 sometimes requests power save entry while not associated - this
will cause problems, so prevent it if not associated. Go to powersave once
association is complete.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In reference source, events are acknowledged separately - fix the driver to
do the same.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While not associated, default the data rates to 1 and 2mbps, so that only
those rates will be used for association related message transfer. Once
associated, configure the full rate-set supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the smart-reflex ACX - the associated parameters are now configured
in the radio parameters config.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure correct values to be used with the smart-reflex configuration of the
firmware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the data path configuration, one of the parameters is the channel. We
have been setting it to wl->channel, which is not correct in this case. This
channel has nothing to do with the channel we're currently tuned to, since it
is only used for calibration during this phase. Hardcoded the channel to 1,
according to the reference driver.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the new reference driver, some of the firmware configuration values have
been changed. This patch changes them in the wl1271 driver accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values. For the latest firmwares, we
should upload only the initial 468 bytes from the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided. It always contains the gpio
power setting (0 = off, 1 = on). To change the power setting, just write 0
or 1 to the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer firmwares require the dco itrim parameters to be set during
initialization. This patch implements the new ACX function and calls it.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init. We should use WL1271_DEFAULT_BASIC_RATE_SET instead. The
values are the same, but the latter is just the correct macro to use.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail. This patch adds the call and now PS seems to
work.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 firmware supports maximun 25.5dBm, so the driver was returning
-EINVALID to anything above that. This patch uses the channel max_power
option to limit the TX power to 25dBm.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we're using a the idle information coming from mac80211 to decide when to
disconnect. If we have joined (ie. we're listening to a channel), whenever
the interface goes to idle, we will issue a disconnect command. So the
workaround to send a disconnect command before joining is not needed anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we need to change the channel before association, we have to send a join
command with a valid BSSID. With this patch we use 0baddeadbeef as the
BSSID. There are ongoing discussions with TI to get this done in a cleaner
way.
When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware
stops listening to the channel and cleans things up internally.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new radio parameters for new structures based on firmware revision
6.1.0.0.288.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were some changes in the values we have to use for these settings. This
patches updates them.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the general parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the radio parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just a clean up and doesn't make a functional difference. It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everything is ready now and we can enable WMM in mac80211.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before transmission when aligning the buffer to 4-byte bounday, tx_hdr
needs to be updated. Otherwise debug logs print false data.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for WMM.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for WMM.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.
Based on a patch for wl1271 by Luis R. Rodriguez.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wakeup time calculation was too complicated, simplify it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original TI driver uses 100 ms timeout ELP wakeup timeout, better
to use the same. Otherwise problems with wakeup might get unnoticed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all return values were checked and one exit from function didn't put
firmware sleep after the error.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This debug message was missing and caused incomplete log messages.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
