There have been a series of checkstops on QS21 related to
ptcal being set up incorrectly. On systems that only
have memory on a single node, ptcal fails when it gets
a pointer to memory on the remote node.
Moreover, agressive prefetching in memcpy and other
functions may accidentally touch the first cache line
of the page that we reserve for ptcal, which causes
an ECC checkstop.
We now allocate pages only from the specified node, moves the
ptcal area into the middle of the allocated page to avoid
potential prefetch problems and prints the address of the
ptcal area to facilitate diagnostics.
Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We're currently choking on mem=4g (and above) due to memory_limit
being specified as an unsigned long. Make memory_limit
phys_addr_t to fix this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Before when we were setting up the irq host map for mpic we passed in
just isu_size for the size of the linear map. However, for a number of
mpic implementations we have no isu (thus pass in 0) and will end up
with a no linear map (size = 0). This causes us to always call
irq_find_mapping() from mpic_get_irq().
By moving the allocation of the host map to after we've determined the
number of sources we can actually benefit from having a linear map for
the non-isu users that covers all the interrupt sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Description
-----------
Change ppc64 oprofile kernel driver to use the SLOT bits (MMCRA[37:39]only on
older processors where those bits are defined.
Background
----------
The performance monitor unit of the 64-bit POWER processor family has the
ability to collect accurate instruction-level samples when profiling on marked
events (i.e., "PM_MRK_<event-name>"). In processors prior to POWER6, the MMCRA
register contained "slot information" that the oprofile kernel driver used to
adjust the value latched in the SIAR at the time of a PMU interrupt. But as of
POWER6, these slot bits in MMCRA are no longer necessary for oprofile to use,
since the SIAR itself holds the accurate sampled instruction address. With
POWER6, these MMCRA slot bits were zero'ed out by hardware so oprofile's use of
these slot bits was, in effect, a NOP. But with POWER7, these bits are no
longer zero'ed out; however, they serve some other purpose rather than slot
information. Thus, using these bits on POWER7 to adjust the SIAR value results
in samples being attributed to the wrong instructions. The attached patch
changes the oprofile kernel driver to ignore these slot bits on all newer
processors starting with POWER6.
Signed-off-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Michael Wolf <mjw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4fc665b88a "powerpc: Merge 32 and
64-bit dma code" made changes to the PCI initialisation code that added
an assignment to archdata.dma_data but only for 32 bit code. Commit
7eef440a54 "powerpc/pci: Cosmetic cleanups
of pci-common.c" removed the conditional compilation. Unfortunately,
the iSeries code setup the archdata.dma_data before that assignment was
done - effectively overwriting the dma_data with NULL.
Fix this up by moving the iSeries setup of dma_data into a
pci_dma_dev_setup callback.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mktree utility defines some variables as "uint", although this is not a
standard C type, and so cross-compiling on Mac OS X fails. Change this to
"unsigned int".
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The interrupt controller was not handling level interrupts correctly
such that duplicate interrupts were happening. This fixes the problem
and adds edge type interrupts which are needed in Xilinx hardware.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It is common to use U-Boot on Xilinx Virtex platforms. This patch
ensures that CONFIG_DEFAULT_UIMAGE is selected for virtex
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver"), possibly due merge issues,
reintroduced completely unneded mpc83xx_wdt_init call, which
I removed some time ago in commit 20d38e01d4
("powerpc/fsl_soc: remove mpc83xx_wdt code").
Remove it once again.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 2657dd4e30 introduced a
bug where we would now always override the "real" oprofile CPU
type with the "compatible" one provided by a pseudo-PVR in the
device-tree which is incorrect and breaks oprofile on all current
configs since the "compatible" ones aren't yet recognized.
This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Oprofile is changing the naming it is using for the compatibility modes.
Instead of having compat-power<x>, oprofile will go to family naming
convention and use ibm-compat-v<x>. Currently only ibm-compat-v1 will
be defined.
The notion of compatibility events just started with POWER6. So there is
no way that any other tool could exist that is using these
oprofile_cpu_type strings we want to change.
Signed-off-by: Mike Wolf <mjw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc/ps3: Fix build error on UP
powerpc/cell: Select PCI for IBM_CELL_BLADE AND CELLEB
powerpc: ppc32 needs elf_read_implies_exec()
powerpc/86xx: Add device_type entry to soc for ppc9a
powerpc/44x: Correct memory size calculation for denali-based boards
maintainers: Fix PowerPC 4xx git tree
powerpc: fix for long standing bug noticed by gcc 4.4.0
Revert "powerpc: Add support for early tlbilx opcode"
Commit edada399 broke the build on 64-bit powerpc because it moved the
__ftr_alt_* sections of a file away from the .text section, causing
link failures due to relative conditional branch targets being too far
away from the branch instructions. This happens on pretty much all
64-bit powerpc configs.
This change reverts commit edada399 while preserving the update from
the *.refok sections to .ref.text that has happened since.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Requested-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A non-SMP version of smp_send_stop() is now included in smp.h.
Remove the unneeded definition in the PS3 smp.c.
Fixes build errors like these when CONFIG_SMP=n:
arch/powerpc/platforms/ps3/setup.c:49: error: redefinition of 'smp_send_stop'
include/linux/smp.h:125: error: previous definition of 'smp_send_stop' was here
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently PPC_CELL_NATIVE selects PPC_OF_PLATFORM_PCI, but does not
select PCI. This can lead to a config with the former and the latter
disabled, which does not build.
To fix this PPC_CELL_NATIVE should select PCI. However, that would
force PCI on for QPACE, which also selects PPC_CELL_NATIVE. So
instead move the select of PPC_OF_PLATFORM_PCI and PCI under both
IBM_CELL_BLADE and CELLEB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64 we implemented elf_read_implies_exec() for 32-bit binaries
because old toolchains had bugs where they didn't mark program
segments executable that needed to be. For some reason we didn't do
this on ppc32 builds. This hadn't been an issue until commit 8d30c14c
("powerpc/mm: Rework I$/D$ coherency (v3)"), which had as a side
effect that we are now enforcing execute permissions to some extent on
32-bit 4xx and Book E processors.
This fixes it by defining elf_read_implies_exec on 32-bit to turn on
the read-implies-exec behaviour on programs that are sufficiently old
that they don't have a PT_GNU_STACK program header.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The section .text.init.refok is deprecated and __REF (.ref.text)
should be used in assembly files instead. This patch cleans up a few
uses of .text.init.refok in the powerpc architecture.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than adding .ref.text to the powerpc linker script so that we
can use __REF on the powerpc architecture, it seems simpler to switch
to using the generic TEXT_TEXT macro.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'device_type = "soc";' line *is* needed in the DTS for get_immrbase()
to return the correct address.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This has the consequence of changing the section name use for head
code from ".text.head" to ".head.text". Since this commit changes all
users in the architecture, this change should be harmless.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix modular build of ide-pmac when mediabay is built in
powerpc/pasemi: Fix build error on UP
powerpc: Make macintosh/mediabay driver depend on CONFIG_BLOCK
maintainers: Fix PS3 patterns
powerpc/ps3: Fix CONFIG_PS3_FLASH=n build warning
powerpc/32: Don't clobber personality flags on exec
powerpc: Fix crash on CPU hotplug
powerpc/85xx: Remove defconfigs that mpc85xx_{smp_}defconfig cover
powerpc/85xx: Added SMP defconfig
powerpc/85xx: Enabled a bunch of FSL specific drivers/options
powerpc/85xx: Updated generic mpc85xx_defconfig
powerpc: don't disable SATA interrupts on Freescale MPC8610 HPCD
fsl_rio: Pass the proper device to dma mapping routines
powerpc: Fix of_node_put() exit path in of_irq_map_one()
powerpc/5200: defconfig updates
powerpc/5200: Add FLASH nodes to lite5200 device tree
powerpc/device-tree: Document MTD nodes with multiple "reg" tuples
powerpc/of-device-tree: Factor MTD physmap bindings out of booting-without-of
powerpc/5200: Bring the legacy fsl_spi_platform_data hooks back
Some U-Boot versions incorrectly set the number of chipselects to two
for Sequoia/Rainier boards while they only have one chipselect hardwired.
This patch adds a workaround for this, hardcoding the number of chipselects
to one for sequioa/rainer board models and reading the actual value from
the memory controller register DDR0_10 otherwise.
It also fixes another error in the way ibm4xx_denali_fixup_memsize
calculates memory size. When testing the DDR_REDUC bit, the polarity is
backwards. A "1" implies 32-bit wide memory while a "0" implies 64-bit
wide memory.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Previous gcc versions didn't notice this because one of the preceding
#ifs always evaluated to true.
gcc 4.4.0 produced this error:
arch/powerpc/mm/tlb_nohash_low.S:206:6: error: #elif with no expression
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit e996557740. Our HW
guys were able to fix this so it never sees the light of day.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A non-SMP version of smp_send_stop() is now included in smp.h.
Remove the unneeded definition in the pasemi setup.c.
Fixes build errors like these when CONFIG_SMP=n:
arch/powerpc/platforms/pasemi/setup.c:48: error: redefinition of ‘smp_send_stop’
include/linux/smp.h:125: error: previous definition of 'smp_send_stop' was here
Reported-by: subrata@linux.vnet.ibm.com
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix build warnings like these when CONFIG_PS3_FLASH=n:
arch/powerpc/platforms/ps3/os-area.c: warning: 'update_flash_db' defined but not used
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that ppc32 implements address randomization it also wants to inherit
personality flags like ADDR_NO_RANDOMIZE across exec, for things like
`setarch ppc -R' to work. But the ppc32 version of SET_PERSONALITY
forcefully sets PER_LINUX, clearing all personality flags. So be
careful about preserving the flags.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
early_init_mmu_secondary() is called at CPU hotplug time, so it
must be marked as __cpuinit, not __init.
Caused by 757c74d2 ("powerpc/mm: Introduce early_init_mmu() on 64-bit").
Tested-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the vast majority of 85xx platforms are UP we introduce a new SMP
config for the few platforms that have more than one core. Beyond
CONFIG_SMP=y and its dependencies this should be identical to
mpc85xx_defconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ULI 1575 PCI quirk function for the Freescale MPC8610 HPCD was disabling
the SATA INTx interrupt, even when SATA support was enabled. This was safe,
because the SATA driver re-enabled it. But with commit a5bfc471 ("ahci: drop
intx manipulation on msi enable"), the driver no longer does this, and so SATA
support on the 8610 HPCD is broken.
The original quirk function disabled INTx because it caused some other
interrupt problem during early development on this board, but no one remembers
any more what that problem was, and it doesn't seem to occur any more.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver should pass a device that specifies internal DMA ops, but
currently NULL pointer is passed, therefore following bug appears
during boot up:
------------[ cut here ]------------
Kernel BUG at c0018a7c [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
[...]
NIP [c0018a7c] fsl_rio_doorbell_init+0x34/0x60
LR [c0018a70] fsl_rio_doorbell_init+0x28/0x60
Call Trace:
[ef82bda0] [c0018a70] fsl_rio_doorbell_init+0x28/0x60 (unreliable)
[ef82bdc0] [c0019160] fsl_rio_setup+0x6b8/0x84c
[ef82be20] [c02d28ac] fsl_of_rio_rpn_probe+0x30/0x50
[ef82be40] [c0234f20] of_platform_device_probe+0x5c/0x84
[...]
---[ end trace 561bb236c800851f ]---
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: pseries/dtl.c should include asm/firmware.h
powerpc: Fix data-corrupting bug in __futex_atomic_op
powerpc/pseries: Set error_state to pci_channel_io_normal in eeh_report_reset()
powerpc: Allow 256kB pages with SHMEM
powerpc: Document new FSL I2C bindings and cleanup
powerpc/mm: Fix compile warning
powerpc/85xx: TQM8548: update defconfig
powerpc/85xx: TQM8548: use proper phy-handles for enet2 and enet3
powerpc/85xx: TQM85xx: correct address of LM75 I2C device nodes
powerpc: Add support for early tlbilx opcode
powerpc: Fix tlbilx opcode
A randconfig build on powerpc failed with:
dtl.c: In function 'dtl_init':
dtl.c:238: error: implicit declaration of function 'firmware_has_feature'
dtl.c:238: error: 'FW_FEATURE_SPLPAR' undeclared (first use in this function)
- We need firmware.h for these definitions.
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Richard Henderson pointed out that the powerpc __futex_atomic_op has a
bug: it will write the wrong value if the stwcx. fails and it has to
retry the lwarx/stwcx. loop, since 'oparg' will have been overwritten
by the result from the first time around the loop. This happens
because it uses the same register for 'oparg' (an input) as it uses
for the result.
This fixes it by using separate registers for 'oparg' and 'ret'.
Cc: stable@kernel.org
Signed-off-by: Paul Mackerras <paulus@samba.org>
While adding native EEH support to Emulex and Qlogic drivers, it was
discovered that dev->error_state was set to pci_io_channel_normal too
late in the recovery process. These drivers rely on error_state to
determine if they can access the device in their slot_reset callback,
thus error_state needs to be set to pci_io_channel_normal in
eeh_report_reset(). Below is a detailed explanation (courtesy of Richard
Lary) as to why this is necessary.
Background:
PCI MMIO or DMA accesses to a frozen slot generate additional EEH
errors. If the number of additional EEH errors exceeds EEH_MAX_FAILS the
adapter will be shutdown. To avoid triggering excessive EEH errors and
an undesirable adapter shutdown, some drivers use the
pci_channel_offline(dev) wrapper function to return a Boolean value
based on the value of pci_dev->error_state to determine if PCI MMIO or
DMA accesses are safe. If the wrapper returns TRUE, drivers must not
make PCI MMIO or DMA access to their hardware.
The pci_dev structure member error_state reflects one of three values,
1) pci_channel_io_normal, 2) pci_channel_io_frozen, 3)
pci_channel_io_perm_failure. Function pci_channel_offline(dev) returns
TRUE if error_state is pci_channel_io_frozen or pci_channel_io_perm_failure.
The EEH driver sets pci_dev->error_state to pci_channel_io_frozen at the
point where the PCI slot is frozen. Currently, the EEH driver restores
dev->error_state to pci_channel_io_normal in eeh_report_resume() before
calling the driver's resume callback. However, when the EEH driver calls
the driver's slot_reset callback() from eeh_report_reset(), it
incorrectly indicates the error state is still pci_channel_io_frozen.
Waiting until eeh_report_resume() to restore dev->error_state to
pci_channel_io_normal is too late for Emulex and QLogic FC drivers and
any other drivers which are designed to use common code paths in these
two cases: i) those called after the driver's slot_reset callback() and
ii) those called after the PCI slot is frozen but before the driver's
slot_reset callback is called. Case i) all driver paths executed to
reinitialize the hardware after a reset and case ii) all code paths
executed by driver kernel threads that run asynchronous to the main
driver thread, such as interrupt handlers and worker threads to process
driver work queues.
Emulex and QLogic FC drivers are designed with common code paths which
require that pci_channel_offline(dev) reflect the true state of the
hardware. The state transitions that the hardware takes from Normal
Operations to Slot Frozen to Reset to Normal Operations are documented
in the Power Architecture™ Platform Requirements+ (PAPR+) in Table 75.
PE State Control.
PAPR defines the following 3 states:
0 -- Not reset, Not EEH stopped, MMIO load/store allowed, DMA allowed
(Normal Operations)
1 -- Reset, Not EEH stopped, MMIO load/store disabled, DMA disabled
2 -- Not reset, EEH stopped, MMIO load/store disabled, DMA disabled
(Slot Frozen)
An EEH error places the slot in state 2 (Frozen) and the adapter driver
is notified that an EEH error was detected. If the adapter driver
returns PCI_ERS_RESULT_NEED_RESET, the EEH driver calls
eeh_reset_device() to place the slot into state 1 (Reset) and
eeh_reset_device completes by placing the slot into State 0 (Normal
Operations). Upon return from eeh_reset_device(), the EEH driver calls
eeh_report_reset, which then calls the adapter's slot_reset callback. At
the time the adapter's slot_reset callback is called, the true state of
the hardware is Normal Operations and should be accurately reflected by
setting dev->error_state to pci_channel_io_normal.
The current implementation of EEH driver does not do so and requires
this change to correct this deficiency.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
