Commit Graph

15 Commits

Author SHA1 Message Date
Sunil Dutt Undekari
df942e7ba7 cfg80211: Pass TDLS peer capability information in tdls_mgmt
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.

The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.

Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-02-20 11:55:25 +01:00
Kyeyoon Park
fa9ffc7456 cfg80211: Add support for QoS mapping
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.

The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-19 16:29:22 +01:00
Andrei Otcheretianski
b176e62940 cfg80211: aggregate mgmt_tx parameters into a struct
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-02 11:51:52 +01:00
David Spinadel
fc73f11f5f cfg80211: add wdev to testmode cmd
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-12 14:11:37 +02:00
Simon Wunderlich
16ef1fe272 nl80211/cfg80211: add channel switch command
To allow channel switch announcements within beacons, add
the channel switch command to nl80211/cfg80211. This is
implementation is intended for AP and (later) IBSS mode.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-01 18:30:28 +02:00
Arend van Spriel
5de1798489 cfg80211: introduce critical protocol indication from user-space
Some protocols need a more reliable connection to complete
successful in reasonable time. This patch adds a user-space
API to indicate the wireless driver that a critical protocol
is about to commence and when it is done, using nl80211 primitives
NL80211_CMD_CRIT_PROTOCOL_START and NL80211_CRIT_PROTOCOL_STOP.

There can be only on critical protocol session started per
registered cfg80211 device.

The driver can support this by implementing the cfg80211 callbacks
.crit_proto_start() and .crit_proto_stop(). Examples of protocols
that can benefit from this are DHCP, EAPOL, APIPA. Exactly how the
link can/should be made more reliable is up to the driver. Things
to consider are avoid scanning, no multi-channel operations, and
alter coexistence schemes.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-22 15:48:00 +02:00
Stanislaw Gruszka
8125696991 cfg80211/mac80211: disconnect on suspend
If possible that after suspend, cfg80211 will receive request to
disconnect what require action on interface that was removed during
suspend.

Problem can manifest itself by various warnings similar to below one:

WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]()
wlan0:  Failed check-sdata-in-driver check, flags: 0x4
Call Trace:
 [<c043e0b3>] warn_slowpath_fmt+0x33/0x40
 [<f83707c9>] ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]
 [<f83a660a>] ieee80211_recalc_ps_vif+0x2a/0x30 [mac80211]
 [<f83a6706>] ieee80211_set_disassoc+0xf6/0x500 [mac80211]
 [<f83a9441>] ieee80211_mgd_deauth+0x1f1/0x280 [mac80211]
 [<f8381b36>] ieee80211_deauth+0x16/0x20 [mac80211]
 [<f8261e70>] cfg80211_mlme_down+0x70/0xc0 [cfg80211]
 [<f8264de1>] __cfg80211_disconnect+0x1b1/0x1d0 [cfg80211]

To fix the problem disconnect from any associated network before
suspend. User space is responsible to establish connection again
after resume. This basically need to be done by user space anyway,
because associated stations can go away during suspend (for example
NetworkManager disconnects on suspend and connect on resume by default).

Patch also handle situation when driver refuse to suspend with wowlan
configured and try to suspend again without it.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-06 16:35:55 +01:00
Jouni Malinen
355199e02b cfg80211: Extend support for IEEE 802.11r Fast BSS Transition
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the WLAN
driver and NL80211_CMD_FT_EVENT to send FT events from the WLAN driver.
This will carry the target AP's MAC address along with the relevant
Information Elements. This event is used to report received FT IEs
(MDIE, FTIE, RSN IE, TIE, RICIE). These changes allow FT to be supported
with drivers that use an internal SME instead of user space option (like
FT implementation in wpa_supplicant with mac80211-based drivers).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-06 16:35:51 +01:00
Vasanthakumar Thiagarajan
77765eaf5c cfg80211/nl80211: add API for MAC address ACLs
Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.

An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.

Black- and whitelists are supported, but not simultaneously.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-25 18:36:44 +01:00
Johannes Berg
683b6d3b31 cfg80211: pass a channel definition struct
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.

Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:58 +01:00
Johannes Berg
42d97a599e cfg80211: remove remain-on-channel channel type
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:58 +01:00
Johannes Berg
c8442118ad cfg80211: allow per interface TX power setting
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.

Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:11:34 +01:00
Johannes Berg
eeb126e9ee cfg80211: add tracing for P2P Device start/stop
These were missed due to the tracing work having
started on a kernel that didn't have P2P Device
yet, implement them now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-23 19:52:53 +02:00
Beni Lev
14e8a3c47e cfg80211: add tracing to rdev-ops
Add tracing to make debugging cfg80211/mac80211
(or full-mac driver) interaction easier.

Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Hila Gonen <hila.gonen@intel.com>
Tested-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[add a cast to int to sizeof() to avoid warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-18 10:53:37 +02:00
Hila Gonen
e35e4d28b6 cfg80211: add wrappers for registered_device_ops
This will allow adding central tracing like in mac80211.

Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-18 10:53:37 +02:00