- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it
Add
ata_sff_irq_status - encapsulates the IRQ check logic
This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that
ata_sff_sync - ensure writes hit the device
Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.
- ata_sff_pause - 400nS delay
Ensure the command hit the device and delay 400nS
- ata_sff_dma_pause
Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)
The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The handling for PHY_MODE4 was originally just cloned from the
Marvell proprietary driver (with their blessing).
But we can do better than that.
Tidy things up with some judicious mask definitions, to improve maintainability.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Differentiate between bay devices in dock stations and others:
- When an ACPI_NOTIFY_EJECT_REQUEST appears, just signal uevent to
userspace (that is when the optional eject button on a bay device is
pressed/pulled) giving the possibility to unmount file systems and to
clean up. Also, only send uevent in case we get an EJECT_REQUEST
without doing anything else. In other cases, you'll get an add/remove
event because libata attaches/detaches the device.
- In case of a dock event, which in turn signals an
ACPI_NOTIFY_EJECT_REQUEST, immediately detach the device, because it
may already have been gone
* In case of an ACPI_NOTIFY_DEVICE/BUS_CHECK, evaluate _STA to check if
the device has been plugged or unplugged. If plugged, hotplug it, if
unplugged, just signal event to userspace
(initial patch by Matthew Garrett <mjg59@srcf.ucam.org>)
* Call ACPI _EJ0 for detached devices
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use quirk table to assign ALC268_TOSHIBA to COMPAL IFL90/JFL-92 laptops.
No analog output on autoprobe.
Signed-off-by: Tony Vroon <tony@linx.net>
Tested-by: Guri <gurashka@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The field was supposed to allow the creation of an anycast route by
assigning an anycast address to an address prefix. It was never
implemented so this field is unused and serves no purpose. Remove it.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make nlmsg_trim(), nlmsg_cancel(), genlmsg_cancel(), and
nla_nest_cancel() void functions.
Return -EMSGSIZE instead of -1 if the provided message buffer is not
big enough.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also removes an unused policy entry for an attribute which is
only used in kernel->user direction.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also removes an obsolete check for the unused flag RTCF_MASQ.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The neighbor table time of last use information is returned in the
incorrect unit. Kernel to user space ABI's need to use USER_HZ (or
milliseconds), otherwise the application has to try and discover the
real system HZ value which is problematic. Linux has standardized on
keeping USER_HZ consistent (100hz) even when kernel is running
internally at some other value.
This change is small, but it breaks the ABI for older version of
iproute2 utilities. But these utilities are already broken since they
are looking at the psched_hz values which are completely different. So
let's just go ahead and fix both kernel and user space. Older
utilities will just print wrong values.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bad type/protocol specified result in sk leak.
Fix is simple - release the sk if bad values are given,
but to make it possible just to call sk_free(), I move
some sk initialization a bit lower.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Jarek Poplawski <jarkao2@gmail.com>
There is only one function in AX25 calling skb_append(), and it really
looks suspicious: appends skb after previously enqueued one, but in
the meantime this previous skb could be removed from the queue.
This patch Fixes it the simple way, so this is not fully compatible with
the current method, but testing hasn't shown any problems.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's logic in __rfcomm_dlc_close:
rfcomm_dlc_lock(d);
d->state = BT_CLOSED;
d->state_changed(d, err);
rfcomm_dlc_unlock(d);
In rfcomm_dev_state_change, it's possible that rfcomm_dev_put try to
take the dlc lock, then we will deadlock.
Here fixed it by unlock dlc before rfcomm_dev_get in
rfcomm_dev_state_change.
why not unlock just before rfcomm_dev_put? it's because there's
another problem. rfcomm_dev_get/rfcomm_dev_del will take
rfcomm_dev_lock, but in rfcomm_dev_add the lock order is :
rfcomm_dev_lock --> dlc lock
so I unlock dlc before the taken of rfcomm_dev_lock.
Actually it's a regression caused by commit
1905f6c736 ("bluetooth :
__rfcomm_dlc_close lock fix"), the dlc state_change could be two
callbacks : rfcomm_sk_state_change and rfcomm_dev_state_change. I
missed the rfcomm_sk_state_change that time.
Thanks Arjan van de Ven <arjan@linux.intel.com> for the effort in
commit 4c8411f8c1 ("bluetooth: fix
locking bug in the rfcomm socket cleanup handling") but he missed the
rfcomm_dev_state_change lock issue.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tty layer provides a callback that is used when the line discipline
is changed. Some hardware uses this to configure hardware specific
features such as IrDA mode on serial ports. Unfortunately the serial
layer does not provide this feature or pass it down to drivers.
Blackfin used to hack around this by rewriting the tty ops, but those are
now properly shared and const so the hack fails. Instead provide the
proper operations.
This change plus a follow up from the Blackfin guys is needed to avoid
blackfin losing features in this release.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RSK7203 is supportable through the generic machvec, so we add a defconfig
for those bits. This gets updated with more complete board support later.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently, fsl_i2c_of_init() uses the order of the I2C adapter nodes in the
device tree to enumerate the I2C adapters. Instead, let's check for the
cell-index property and use it if it exists.
This is handy for device drivers that need to identify the I2C adapters by
specific numbers. The Freescale MPC8610 ASoC V2 sound drivers are an example.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Both the PNP/PCI conflict detection quirk and the PNP system
driver must use the same mechanism to mark resources as disabled.
I think it's best to keep the resource and to keep the type bit
(IORESOURCE_MEM, etc), so that we match the list from firmware
as closely as possible.
Fixes this regression from 2.6.25: http://lkml.org/lkml/2008/6/1/82
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Tested-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since mmc_spi.h uses irqreturn_t type, it should include appropriate
header, otherwise build will break if users didn't include it (some of
them do not use interrupts).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
8250 Serial Driver: revert extra IRQ flag definition patch
Blackfin arch: update anomaly headers from toolchain trunk
Blackfin arch: Remove bad and usless code
Blackfin arch: Fix bug - set corret SSEL and IRQ to enable AD7877 on BF527
Blackfin arch: Fix typo. it should be _outsw_8
Blackfin arch: Cleanup no functional changes
On machines with more than one exception level any system register that
might be modified by the "normal" exception level needs to be saved and
restored on taking a higher level exception. We already are saving
and restoring ESR and DEAR.
For critical level add SRR0/1.
For debug level add CSRR0/1 and SRR0/1.
For machine check level add DSRR0/1, CSRR0/1, and SRR0/1.
On FSL Book-E parts we always save/restore the MAS registers for critical,
debug, and machine check level exceptions. On 44x we always save/restore
the MMUCR.
Additionally, we save and restore the ksp_limit since we have to adjust it
for each exception level.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
* Cleanup the code a bit my allocating an INT_FRAME on our exception
stack there by make references go from GPR11-INT_FRAME_SIZE(r8) to
just GPR11(r8)
* simplify {lvl}_transfer_to_handler code by moving the copying of the
temp registers we use if we come from user space into the PROLOG
* If the exception came from kernel mode copy thread_info flags,
preempt, and task pointer from the process thread_info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
For the additonal exception levels (critical, debug, machine check) on
40x/book-e we were using "static" allocations of the stack in the
associated head.S.
Move to a runtime allocation to make the code a bit easier to read as
we mimic how we handle IRQ stacks. Its also a bit easier to setup the
stack with a "dummy" thread_info in C code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Added next-level-cache to the L1 and a reference to the new L2 label.
This is per the ePAPR 0.94 spec. Since we are't really dependent on this
today we aren't supporting the "legacy" l2-cache phandle that is specified
in the PPC v2.1 OF Binding spec.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed clock-frequency, big-endian, and built-in props as they aren't
specified anywhere. Also added compatible = "chrp,open-pic" in the
places it was missing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The i2c_devices[] array in fsl_soc.c lists all the I2C nodes that are supported
on Freescale boards. Add an entry for the Cirrus Logic CS4270 so that a
new-style CS4270 driver will work.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update of_find_i2c_driver in fsl_soc.c to display a warning message if an
I2C node in the device tree isn't found in the i2c_devices[] array.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes few cosmetic issues, also removes unused function,
makes some functions static and reduces #ifdef count.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enabled MSI on 8544ds and 8572ds board.
So far only one MSI interrupt can generate on 8544 board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enable the MSI on 8610hpcd board.
Through the msi-available-ranges property, All the 256
msi interrupts can be tested on this board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This MSI driver can be used on 83xx/85xx/86xx board.
In this driver, virtual interrupt host and chip were
setup. There are 256 MSI interrupts in this host, Every 32
MSI interrupts cascaded to one IPIC/MPIC interrupt.
The chip was treated as edge sensitive and some necessary
functions were setup for this chip.
Before using the MSI interrupt, PCI/PCIE device need to
ask for a MSI interrupt in the 256 MSI interrupts. A 256bit
bitmap show which MSI interrupt was used, reserve bit in
the bitmap can be used to force the device use some designate
MSI interrupt in the 256 MSI interrupts. Sometimes this is useful
for testing the all the MSI interrupts. The msi-available-ranges
property in the dts file was used for this purpose.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Work around:
arch/arm/mach-pxa/tosa.c: In function `tosa_poweroff':
arch/arm/mach-pxa/tosa.c:470: error: `GPIO_OUT' undeclared (first use in this function)
arch/arm/mach-pxa/tosa.c:470: error: (Each undeclared identifier is reported only once
arch/arm/mach-pxa/tosa.c:470: error: for each function it appears in.)
The proper fix exists in the PXA branch of my kernel git tree, which
will be pushed during the next merge window.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current __raw_write_can_lock macro tests whether the lock can be
locked by checking if it is equal to 0x80000000, whereas the lock
should be lockable if its value is 0 i.e. unlocked state is
represented by 0. Hence the macro should test the value of lock
against 0 and not 0x80000000.
Signed-off-by: Surinder Pal Singh <srplsnh@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some additional alternate gpio definitions relating
to FFUART and USB on the pxa27x. These are used on
the xbow imote2 platform.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the IORESOURCE_IRQ_HIGHEDGE to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the IORESOURCE_IRQ_HIGHEDGE to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
