Disable the amplifiers for the headset outputs, and do not select
routings by default to the headset outputs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OSCSET calculation was not correct in case of 44.1KHz
sampling rate.
With small adjustment both 48 and 44.1 KHz calculation
now gives the correct value.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In repeated playback the FIFOFLUSH bit remained set, and
never has been cleared.
Clear it during the setup phase.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a sysfs file allowing userspace to inspect and change the
pmdown_time setting at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Make the pmdown_time a per-card setting rather than a global one,
initialised before the card initialisation runs. This allows cards
to override the default setting if it makes sense to do so (for
example, due to an unavoidable pop).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM2000 is a low power, high quality handset receiver speaker
driver with Wolfson myZone™ Ambient Noise Cancellation (ANC). It
provides enhanced voice communication quality in a noisy environment
if the handset acoustics are designed appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Audio on Migo-R cannot work if CONFIG_SH_DMA_API=y, but compilation should not
break anyway.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch expands the omap3beagle sound soc for the
beagle board clone DevKit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The serial interface (TDM/I2S) for the audio block have been
constantly enabled.
Introduce a new DAPM_SUPPLY for handling the AIF_EN bit, so
the interface is only enabled, when there is a need for it.
For example when only the analog loopback is enabled, there
is no need to keep the serial interface active.
I have added the persons who contributed to the Voice path
of twl4030 codec driver, so they might have the ability
to test this patch, and send an update for the Voice path,
if it is necessary
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable the bulk regulators at probe time so we can safely disable them
again when going to suspend without confusing the reference counter.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds sound support for Phytec PhyCORE / PhyCARD
modules in AC97 mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pandora's external DAC is connected to VSIM TWL4030 supply, so let's
start switching it too to save more power.
Also DAC got it's own DAPM handler.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pandora's external DAC is using 256*Fs output from the TWL4030
codec, and TWL4030 needs to have APLL enabled for it's 256*Fs
output to function.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The module unloading path had several problems:
- it freed up the private structure twice
- it freed up the codec structure, which was allocated as part
of the private structure
- it did not freed up the reg_cache
- it did not unregistered the dais and the codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8912 is a DAC only device register compatible with the WM8904
CODEC with ADC portions omitted. Support it within the WM8904 driver
based on the configured I2C device name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Handle the output PGAs as part of the output powerup since they can
never be powered separately and reorder things so that we remove the
output shorts after both line and headphone outputs have been brought
up, minimising the opportunity for any issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
As well as disabling the biases of the CODEC the drop into BIAS_OFF will
also disable all the regulators powering the CODEC, allowing even greater
power savings on appropriately configured systems.
Since the regulator API does not currently provide notification when
regulators are disabled we assume that this always happens when we stop
using the regulators. Once 2.6.34 is merged this code can be optimised
to only sync the cache when power was actually removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
While the regulators are disabled we cache all register writes.
Currently we assume that the regulator disable actually takes
effect, after the merge with the regulator tree in 2.6.34 the
regulator API will be able to notify us if the power is actually
removed (due to constraints or regulator sharing it may not be).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
At the minute the regulators are simply enabled for the entire
lifetime of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a bit to the CODEC structure indicating if a cache sync is required.
By default this will be set if a cache only write is done to a soc-cache
register cache. This allows us to avoid syncing the cache back after
using cache only writes if there were no changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently the soc-cache code will always write to the device, meaning
that we need the device to be powered and active at pretty much all
times the system is active. Allowing cache only writes lays some
groundwork for future enhancements to allow devices to be put into a
full off state when the audio subsystem is idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
ctrl_outl() has become void at some point, which breaks compilation of fsi.c.
Make writing functions void, as their output is anyway not evaluated, and use
__raw_writel and __raw_readl instead of deprecated ctrl_outl and ctrl_inl
respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unconditionally save the register states when suspending and restore
them again at resume time. Register contents were not preserved over
suspend, and hence the driver takes false assumptions about them.
The clock must be enabled to access the register block.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dependency on MFD_WM8994 rather than I2C went awry.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8994 is a highly integrated ultra-low power hi-fi audio subsystem
designed for smartphones and other portable devices rich in multimedia
features. It provides advanced digital mixing facilities enabling low
power high quality interconnection of CPU, baseband and other audio
sources through flexible digital and analogue routing, and integrates
a class W headphone driver and stereo class D speaker drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use a two code correction for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Perform DC servo offset calibration using a series update sequence
rather than startup update sequence, tuning the configuration of the
WM8993 DC servo to make best use of this.
Also introduce currently unused data allowing us to correct for
any systematic errors in the DC servo calibration results and an
alternative startup path for the headphone output which performs
better with some chip revisions. The alternative setup sequence is
enabled for WM8993.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case, if OPCLK is not used, and PLL is used for driving the codec, the
choice of PLL output frequency could result in a needlessly imprecise
system clock frequency. Use an iterative process to select a precise
configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm8974 and wm8978 codec drivers control DAC and ADC oversampling rates in their
.set_clkdiv() methods, which is wrong, because these are simple boolean
switches and not clock dividers. Move these bits to sound controls. Also remove
manual configuration of the MCLK divider in wm8978, since it is configured
automatically.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tests showed, that bit 6 of the WM8978_POWER_MANAGEMENT_2 register of wm8978
affects codec clocks. Being useless for suspend / resume, it cannot be used in
bias-level control either. Remove this bit handling.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for audio on sh7722-based Migo-R boards, using SIU and wm8978
codec, recording via external microphone and playback via headphones are
implemented.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's more robust when references are provided in control names
rather than numid.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 761c9d45 (ASoC: Fix build of OMAP sound drivers) changes
CONFIG_MACH_OMAP3517EVM -> CONFIG_SND_OMAP_SOC_OMAP3517EVM in the
Makefile. Whereas the config option defined in Kconfig is
SND_OMAP_SOC_AM3517EVM. Because of this, ASoC driver for AM3517
was not getting compiled.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit e9ff5eb2 (Fixing infinite loop in resume path) uses wrong AIC23
register in resume function because of which register writes happen
on some non-existing registers.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also renames a few things to make volumes and switches match up in
alsamixer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The version isn't being updated or used, the kernel revision
tracking is enough.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change the legacy default register configuration, which left some
internal components on.
Now we have either DAPM, or other ways to control these bits,
so there is no need to enable them by default.
The affected parts:
Disable ADCL and ADCR
Disable ARXL2 and ARXR2 analog PGA (playback)
Disable APLL by default
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fsi_master_xxx function should be protected by spin lock,
because it are used from both FSI-A and FSI-B.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8978 codec from Wolfson Microelectronics is very similar to
wm8974, but is stereo and also has some differences in pin configuration
and internal signal routing. This driver is based on wm8974 and takes
the differences into account.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The board supports both GPIO sets for the AC97 bus and the analogue
outputs can be switched between this and the WM8580 so add some
comments saying what the setup the standard kernel expects is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since, we have generic AC97 controller driver and all the machines
have moved to that, there is no need for old s3c2443-ac97.c to exist.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Switch to use s3c-ac97.c AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Switch to use s3c-ac97.c AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the common machine driver for SMDKs that
have a WM9713 codec attched to the AC97 controller.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the AC97 controller driver for Samsung SoCs that have one.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <Barry.Song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <Barry.Song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes after a suspend-resume cycle, the ALSA application
restarts the stream when resume fails and McASP fails to work
as the clock is not enabled. This patch corrects this bug.
Testes on TI DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
tests show frequent suspend/resume(frequent poweroff/on ad1836 internal
components) maybe make ad1836 clock mode wrong sometimes after wakeup.
This patch reset/restore ad1836 clock mode while executing PM, then
ad1836 can always resume to right clock status.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Several SuperH platforms, including sh7722, sh7343, sh7354, sh7367 include
a Sound Interface Unit (SIU). This patch adds DAI and platform / DMA
drivers for this interface.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remember to free the temporary register-cache.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This provides a small power saving when audio is inactive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently ASoC always maintains the bias of the CODEC while the system
is active. With older mobile CODECs this is required since the outputs
are referenced to a non-zero voltage and enabling or disabling this
voltage without audible pops or clicks in the output takes too long to
do when starting or stopping audio.
As a result of features such as ground referenced outputs and class D
speaker drivers current generation devices are able to power on and off
much more quickly without these system level issues so provide a new
flag idle_bias_off in snd_soc_codec which will cause the core to turn
off the CODEC bias. The distinction between STANDBY and OFF is still
maintained. This is partly for consistency but also allows for
potential future extensions such as per-machine overrides or deferring
the bias removal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The same information is now visible via debugfs and with large modern
devices dumping everything to the console can be very resource
intensive, causing more harm than good.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add possibility to configure the burst mode BCLK divider through platform
data structure.
The BCLK divider changes the actual speed of the serial bus in burst mode,
which is faster than the sampling frequency of the running stream.
In this way platforms can experiment with the optimal burst speed without
the need to modify the codec driver itself.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The BCLK divider was not configured in case of mode7.
This leads to unpredictable behavior when switching between FIFO modes.
Configure the BCLK divider depending on the fifo_mode (FIFO is in use,
or FIFO bypass).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the prefill number of samples as the same as the lower
threshold in mode7.
In this way the codec will read the same amount of data on
startup and during the running playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently they don't build due to cross tree dependencies, they will be
reenabled once the arch/arm side has merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This has been superceeded by Sascha's new driver but was not removed in
the patch series due to cutdowns for review.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While dynamically allocated DAIs are the way forward the core doesn't
yet support anything except matching with a pointer to the actual DAI
so convert to doing that so that machine drivers don't have to jump
through hoops to register themselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Don't unconditionally include the i.MX2x DMA driver, the arch/arm
functions it uses aren't available for i.MX3x.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
The old driver has the number of SSI units in the system hardcoded,
does not make use of the device model and works only on i.MX21/27.
This driver replaces it. It works in DMA mode on i.MX21/27 and using
an FIQ handler on other systems. It also supports AC97 mode of
the SSI units.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for sample rates other than 44100Khz on raumfeld audio
devices. At startup time, call snd_soc_dai_set_sysclk() with 0 as 'freq'
argument so it offers all the sample rates. Later, the function is
called again to give proper constraints.
Use the external audio clock generator to provide double data rate
clocks as the PXA's internal baud generator does anything but what's
described in the datasheets.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For setups with variable MCLKs, the current logic of limiting the
available sampling rates at startup time is not sufficient. We need to
be able to change the setting at a later point, and so the codec must
offer all possible rates until the hw_params are given.
This patches allows that by passing 0 as 'freq' argument to
cs4270_set_dai_sysclk().
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The transmitter supports all sample rates up to 192KHz, so the driver
should not give a limit.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The codec structure initialization statements should be
separated by semicolons.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
tpa6140a2 uses different names for the regulators.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to set the LRCLK inversion bit to select DSP mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Initialize the glue by calling snd_soc_new_ac97_codec() as is done
in other ASoC AC97 codecs. Fixes an oops caused by dereferencing
uninitialized members in snd_soc_new_pcms().
Run-tested on Au1250.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Better integration of the core with the device model means that we now
no longer get the ASoC suspend and resume callbacks without the card
having been set up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The currently available FIFO modes (mode1 and mode7) require master
mode from the codec.
Do not allow the slave configuration when the FIFO is in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mode 7 of tlv320dac33 operates in the following way:
The codec is in master mode.
Host configures upper and lower thresholds in tlv320dac33
During playback the codec will clock in the data until the
upper threshold is reached in FIFO. At this point the codec
stops the colocks on the serial bus.
When the FIFO fill is reaching the lower threshold limit the
codec will enable the clocks on the serial bus, and clocks
in data till the upper threshold is reached.
In this mode, we can also request interrupts for threshold
events (upper, lower and alarm), which could be used for
power management.
At this point the interrupts are not enabled for this mode,
but it can be taken into use in the future, when the surrounding
code makes it possible to use it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.oc.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use switch instead of if statements to configure FIFO bypass
and mode1.
With this change adding new FIFO mode is going to be easier,
and cleaner.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the code is going to be readable, when new FIFO modes
are introduced later.
Move the prefill and playback state handling to inlined
functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to have support for more FIFO modes supported by
tlv320dac33, the switch for enabling/disabling the FIFO
use has to be replaced with an enum.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
PM architecture of ad1938 is simple, we don't need a bundle of functions like
ad1938_pll_powerctrl, ad1938_set_bias_level for only PLL. A dapm supply will
handle on/off of PLL.
Since soc-core can poweron/off PLL on-demand, we don't need to poweron/off PLL
in suspend/resume entries too.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tests show frequent suspend/resume(frequent poweroff/on ad1836 internal
components) maybe make ad1836 clock mode wrong sometimes after wakeup.
This patch reset/restore ad1836 clock mode while executing PM, then
ad1836 can always resume to right clock status.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sevelar ASoC codec drivers wrongly assume, that the params_rate() macro
returns one of SNDRV_PCM_RATE_* defines instead of the actual numerical
sampling rate. Fix them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
I2C devices should be registered when platform board setting
in latest ASoC.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a bug where "virtual" registers were being written to the ac97
bus. This was causing unrelated registers to become corrupted (headphone 0x04,
touchscreen 0x78, etc).
This patch duplicates protection that was included in the wm9713 driver.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Commit 2ccafed4 added an extra parameter to the DAI .set_pll() method, but
it missed this call in sound/soc/imx/mx27vis_wm8974.c.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8955 is a low power, high quality stereo DAC with integrated
headphone and loudspeaker amplifiers, designed to reduce external
component requirements in portable digital audio applications. This is
an initial driver implementing support for the majority of the
functionality in the device, currently OUT3 is not supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The wm8974 datasheet defines BUFIOEN as bit 2.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
DAC_VOICE_EN was not defined - looks to have been overly enthusiastically
deleted from a previous revision of the patch, pull the value from v1.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fix precision of PLL computation for TLV320AIC3x SoC driver,
test results are at http://pmeerw.net/clk
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Vladimir Barinov <vova.barinov@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This original driver was created by Dialog Semiconductor,
and cleanuped by Kuninori Morimoto.
Special thanks to David Chen.
This became very simple ASoC codec driver,
and it is tested by EcoVec24 board.
Signed-off-by: David Chen <Dajun.chen@diasemi.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Take the regulator framework in use for managing the power sources
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver can be 'generalized' a bit by not hardcoding '2'(the number of
I2Sv3 controllers that the driver can handle) at many places, instead we
define a macro for it. That makes it easier to increase number of controllers
by changing the parameter at just one place, this will be useful when there is
support for newer SoCs, which have the same controller, only more in number.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Removed redundant header includes which make no difference to compilation.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for multiple device support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
No need for the mixers to know about this, and it allows for virtual
controls.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change code so that switching to playing music through the analog output
disables SPDIF out instead of disabling it when stream ends.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ac97_codec - increase timeout for analog sections to 5 second
ASoC: Correct code taking the size of a pointer
ALSA: hda - Add PCI IDs for Nvidia G2xx-series
ALSA: sound/isa/gus: Correct code taking the size of a pointer
ALSA: hda: Fix max PCM level to 0 dB for AD1981_HP
ALSA: hda: Use ALC260_WILL quirk for another Acer model (0x1025007f)
If ak4642 driver was compiled without I2C configs,
ak4642_modinit return value will become un-stable.
This patch modify this bug
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sizeof(codec->reg_cache) is just the size of the pointer. Elsewhere in the
file, codec->reg_cache is used with sizeof(wm8900_reg_defaults), so the
code is changed to do the same here.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Bring the WM8350 IRQ API more in line with the generic IRQ API by
masking and unmasking interrupts as they are requested and freed.
This is mostly just a case of deleting the mask and unmask calls
from the individual drivers.
The RTC driver is changed to mask the periodic IRQ after requesting
it rather than only unmasking the alarm IRQ. If the periodic IRQ
fires in the period where it is reqested then there will be a
spurious notification but there should be no serious consequences
from this.
The CODEC drive is changed to explicitly disable headphone jack
detection prior to requesting the IRQs. This will avoid the IRQ
firing with no jack set up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is done as simple code transformation, the semantics of the
IRQ API provided by the core are are still very different to those
of genirq (mainly with regard to masking).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Overwrite pin config on intel DG45ID board.
intelhdmi - dont power off HDA link
ALSA: hrtimer - Fix lock-up
ALSA: intelhdmi - add channel mapping for typical configurations
ALSA: intelhdmi - channel mapping applies to Pin
ALSA: intelhdmi - accept DisplayPort pin
ALSA: hda - show HBR(High Bit Rate) pin cap in procfs
ALSA: hda - Fix LED GPIO setup for HP laptops with IDT codecs
ASoC: Fix build of OMAP sound drivers
ALSA: opti93x: fix irq releasing if the irq cannot be allocated
There are build errors when building for some of the omap2/3 boards without
enabling sound:
sound/built-in.o:(.data+0x43bc): undefined reference to `soc_codec_dev_tlv320aic23'
sound/built-in.o:(.data+0x43cc): undefined reference to `tlv320aic23_dai'
Confused me quite a bit since the drivers that had references to the
codec weren't enabled. Turns out the Makefile was using the wrong
config option to enable them. Patch below.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The wrong variable was returned in the case of an error
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8904 is a high performance ultra-low power stereo CODEC
optimised for portable audio applications, with features including
a class W amplifier, FLL with free running mode, Mobile ReTune and
ground referenced headphone and line outputs.
Support for some features, most particularly the digital microphone
interface, is not yet present.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Make it a bit easier to tie DAPM widgets in with the register map
without referring to the source by including the register location
controlled by the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Take the regulator framework in use for managing the power sources.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add clock enable and disable calls to resume and suspend respectively.
Also add a member to the audio device data structure which tracks the clock
status.
Tested on DA850/OMAP-L138 EVM. For the purpose of testing, the patches[1] which
add suspend-to-RAM support to DA850/OMAP-L138 SoC were applied.
[1] http://linux.davincidsp.com/pipermail/davinci-linux-open-source/
2009-November/016958.html
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This renames from a character / to : of controls. A / occurs below error
messages.
ASoC: Failed to create IN2RP/VXRP debugfs file
ASoC: Failed to create IN2LP/VXRN debugfs file
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI driver use global variable to access device data.
But this style will be broken
if SuperH come with multiple FSI blocks in future.
To solve this problem, this patch use cpu_dai->private_data.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
free the allocated pcm platform device in the error path.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
platform_device_unregister() frees resources for us, no need to
do it explicitly. Fixes an oops when machine code removes the
soc-audio device.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA's for-2.6.33 branch has a new source argument to
snd_soc_dai_set_pll().
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add support runtime PM.
Driver callbacks for Runtime PM are empty because
the device registers are always re-initialized after
pm_runtime_get_sync(). The Runtime PM functions replaces the
clock framework module stop bit handling in this driver.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes two issues:
a) Infinite loop in resume function
b) Writes to non-existing registers in resume function
Cc: stable@kernel.org
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit fe3e78e073
ASoC: Factor out snd_soc_init_card()
removed the error paths that are still valid for wm97* codecs, causing
the compile errors like
sound/soc/codecs/wm9705.c:399: error: label 'reset_err' used but not defined
sound/soc/codecs/wm9712.c:687: error: label 'reset_err' used but not defined
sound/soc/codecs/wm9713.c:1237: error: label 'reset_err' used but not defined
Revert the removed error path codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RT workqueue is going away in the near future, replace it with
singlethread wq for now, which is still supported.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we get a stream suspend event force the power down since otherwise
the stream would remain marked as active. In future we'll probably want
to make this stream-specific and add an interface to make the power down
of other widgets optional in order to support leaving bypass paths
active while suspending the processor.
Cc: stable@kernel.org
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use edma_pause and edma_resume to make missing dma_events
less likely. This may not be needed, but it looks better.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix underruns by using dma to copy 1st to sram
in a ping/pong buffer style and then copying from
the sram to the ASP. This also has the advantage
of tolerating very long interrupt latency on dma
completion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename variable master_lch to asp_channel
Rename variable slave_lch to asp_link[0]
Rename local variables:
lch to link
count to asp_count
src to asp_src
dst to asp_dst
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the left and right 16 bit samples to be shifted out as 1
32 bit sample.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the ordering of sr_valid_mask array.
The lower bit of the index represents USB
not bosr.
Reported-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A while ago TWL4030 had it's playback stream name changed, but
pandora needs it for it's playback path. Update to correct stream
name so that playback works again.
Also mark VIBRA output as not connected.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correcting the license string from GPLv2 -> GPL v2.
Found the problem while building OMAP3 ASoC driver as
module.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove requirement that dma_params is 1st in the structures
davinci_audio_dev and davinci_mcbsp_dev.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Making room for namespace for the PCM Controller driver
the platform driver(s3c24xx-pcm) has been renamed to SoC
agnostic name 's3c-dma'.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The s3c24xx_pcm prefix for the soc_platform is inappropriate when
some Samsung SoCs have PCM controllers which will eventually have
drivers and hence namespace ambiguities.
To resolve naming ambiguities in future the following have been
renamed in order
1) s3c24xx_pcm_dma_params -> s3c_dma_params
2) s3c24xx_pcm_preallocate_dma_buffer -> s3c_preallocate_dma_buffer
3) s3c24xx_pcm_dmamask -> s3c_dma_mask
4) s3c24xx_pcm_XXX -> s3c_dma_XXX
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAPM widgets are now insntantiated by the core when creating the card
so there is no need for the individual CODEC drivers to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The jack_status_check callback function is the interface to check the
status of the jack. Some target provides the method to distinguish what
is the jack inserted - headphone jack, microphone jack, tvout jack, etc,
so we can implement it using the jack_status_check function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While probing, AC97 codec drivers and soc-core generically execute the
following sequence:
snd_soc_new_ac97_codec -> snd_soc_new_pcms -> reset ac-link/read AC97 ID
to detect ->... -> set platform_data to ac97 by soc-core
commit 474828a40f adds platform_data to
snd_ac97 instance. But ac97 platform data hasn't given to snd_ac97
before actual ac97 operations. Then while ac97_read access platform_data
of snd_ac97 for detecting, NULL pointer oops will fire. That means old
platform_data patch doesn't work in real-life cases.
This patch moves the operation of setting ac97 platform_data earlier
than ac97 reading/writing operations. Then it makes platform_data of
AC97 become practically useful.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
