To support various EXYNOS series SoCs commonly,
added exynos common structure.
exynos-cpufreq.c => EXYNOS series common cpufreq driver
exynos4210-cpufreq.c => EXYNOS4210 support cpufreq driver
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The driver uses __napi_complete and napi_gro_receive. Without it, the
driver hits the BUG_ON(n->gro_list) assertion hard in __napi_complete.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Marin Glibic <zhilla2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change default clock rate of GPIO based I2C operation for BF533
and BF561 to bring up the I2C interface LCD display
Signed-off-by: Aaron Wu <Aaron.Wu@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
disable preemption when icache flush and use wait mode cross call, hold the msg
queue lock while handle cross function call to avoid overflow
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Macro name for spi controller driver has been modified, so update default
board file accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Config name for spi controller driver has been modified in previous commit,
so update default config accordingly.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
move idle task point to percpu blackfin_cpudata and add smp_timer_broadcast
interface.
enable SUPPLE_1_WAKEUP and add BFIN_IPI_TIMER ipi support.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Add IRQF_NO_SUSPEND | IRQF_FORCE_RESUME to irq flags, supplement irq should
not be disabled when system do suspend.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
ASoC drivers changed between 2.6.37 and 3.0, but we didn't apply these changes
in bf533 board file.
So apply missed patches for asoc since 2.6.37 together.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
The ASoC codec name is "ad1836" and not "ad183x" as the change to rename
things ultimately did not get merged.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
The renesas_usbhs driver doesn't use the clk functions. So, even if we
adds "CLKDEV_DEV_ID("renesas_usbhs.0", ...)" only, we cannot use the USB
controller because clk_late_init() will disable the clock by "usb0".
So, the patch also removes the "CLKDEV_CON_ID("usb0", ...)".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add cache flushing code to the SH-Mobile specific CPU hotplug
implementation. While at it, add a cpu mask to make sure the
cache flushing code is finished in platform_cpu_die() before
letting the SoC-specific code in shmobile_platform_cpu_kill()
proceed with turning off power.
Without this code CPU hotplug offline fails when cache is
enabled on Cortex-A9 based SoCs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the function shmobile_platform_kill_cpu() to allow
SoC specific code to tie in their CPU shutdown code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the low level SMP assembly code for SH-Mobile ARM
from using the INIT to the CPUINIT section. This unbreaks
onlining of CPUs using the CPU hotplug interface:
echo 1 > /sys/devices/system/cpu/cpu1/online
Without this fix the reset vector code used by CPU hotplug
will be freed as init section data and CPU cores cannot
be brought online.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Both ext3 and ext4 put the half-created symlink inode into the orphan list
for a while (see the comment in ext[34]_symlink() for gory details). Then,
if everything went fine, they pull it out of the orphan list and bump the
link count back to 1. The thing is, inc_nlink() is going to complain about
seeing somebody changing i_nlink from 0 to 1. With a good reason, since
normally something like that is a bug. Explicit set_nlink(inode, 1) does
the same thing as inc_nlink() here, but it does *not* complain - exactly
because it should be usable in strange situations like this one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We have already set ->s_root, so ->put_super() is going to be called.
Freeing ->s_fs_info is a bloody bad idea when it's going to be
dereferenced very shortly...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
devpts_kill_sb() is called even if devpts_fill_super() fails;
we should not do that kfree() in the latter, especially not
with ->s_fs_info left pointing to freed object. Double kfree()
is a Bad Thing(tm)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add SCIF2 and SCIF4 pin configuration code to
the r8a7779 Marzen board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add GPIO-only r8a7779 PFC support V2.
Only regular GPIOs are supported at this time. GPIO_FN are not
supported because they require variable bit width support in be
the shared pfc code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* if you do dput() of root dentry, do *not* follow that with iput() of root
inode.
* while we are at it, don't do that dput() at all - you are leaving the pointer
in ->s_root and your ->kill_sb() will be very unhappy with that. It will do
proper dput(), though, so the easiest way is to leave that to it entirely.
* freeing ->s_fs_info is also best left to ->kill_sb() (which will do it
anyway), especially since we leave the pointer in place.
* that xchg() in ->kill_sb() is not a bug per se, but it's a plain and simple
masturbation with fewer excuses than Onan had...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Initial support for the r8a7779 SoC and the Marzen board (V2).
Only SCIF ports and the TMU are supported at this point.
To keep things simple only entity-mapped virt-to-phys mappings
are supported. This forces drivers and other SoC glue code to
make use of ioremap(). We cannot support early serial console
due to virtual address space collisions with the ARM kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add PFC support for a 32-bit unlock register. Needed to
drive the r8a7779 PFC that comes with a funky PMMR register.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for variable config reg hardware by adding
the macro PINMUX_CFG_REG_VAR(). The width of each bitfield
needs to be passed to the macro, and the correct space must
be consumed by each bitfield in the enum table following the
macro. Data registers still need to have fixed bitfields.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a helper function for shared config reg access
calculations. This allows us to reduce the amount
of duplicated code, and at the same time prepare
for a common place for future variable bitwidth
config reg support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the way the PFC code is passing bitfield
selection between configure register functions.
Convert the code from using index only to bitfield
number and selected value. First step towards future
variable bitfield width support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Introduce gpio_read_bit() for data register read access
and modify sh_gpio_get_value() to make use of the new
function instead of gpio_read_reg(). The purpose of
this change is to update the code to only use the
gpio_read_reg() function for config register access.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The AHCI controller found in the STA2X11 chip uses BAR number 0
instead of 5. Also, the chip's fixup code sets a special DMA mask
for all of its PCI functions, and the mask must be preserved here.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The author of this driver clearly wasn't familiar with the BMIDE specification
(also known as SFF-8038i) when he implemented the bmdma_status() method: first,
the interrupt bit of the BMIDE status register corresponds to nothing else but
INTRQ signal (ATAPI_DEV_INT here); second, the error bit is only set if the
controller encounters issue doing the bus master transfers, not on the IDE DMA
burst termination interrupts like here (moreover, setting the error bit doesn't
cause an interrupt). We now need to disable all those unused interrupts...
(The only thing I couldn't figure out is how to flush the FIFO to memory once
the interrupt happens as required by the mentioned spec.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ata port is brought back to full power state during system resume.
So its runtime PM status will have to be updated to reflect
the actual post-system sleep status.
This also fixes below warning during system suspend/resume.
WARNING: at /work/linux/drivers/ata/libata-eh.c:4034
ata_scsi_port_error_handler+0x89/0x557()
4034 WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[Patch description from Alan Stern]
If a child device was runtime-suspended when a system suspend began,
then there will be nothing to prevent its parent from
runtime-suspending as soon as it is woken up during the system resume.
Then when the time comes to resume the child, the resume will fail
because the parent is already back at low power.
On the other hand, there are some devices which should remain at low
power across an entire suspend-resume cycle. The details depend on the
device and the platform.
This suggests that the PM core is not the right place to solve the
problem. One possible solution is for the subsystem or device driver
to call pm_runtime_get_sync(dev->parent) at the start of the
system-resume procedure and pm_runtime_put_sync(dev->parent) at the
end.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add platform hooks for custom suspend() and resume() functions. The
generic suspend/resume code in drivers/ata/ahci_platform.c is adapted
from the PCI version in drivers/ata/ahci.c.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
