Based on:
NICInitRT5592BbpRegisters()
NICInitBBP()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
NICInitRT5592MacRegisters()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
On vendor driver we do not initialize TX_SW_CFG{1,2}. However the same
difference is between rt2x00 and vendor driver for 5390 chip.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_ChipSwitchChannel()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_ChipSwitchChannel()
RT5592_Frequency_Plan_Xtal20M[]
RT5592_Frequency_Plan_Xtal40M[]
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add basic defines for 5592 chip. It can not be enabled until
CONFIG_RT2800USB_RT55XX configuration option will be provided in the
Kconfig.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case the spec->channels was not specified, print warning instead
of hard crash the kernel.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 hardware sometimes reorders tx frames when transmitting to
multiple BA enabled STAs concurrently.
For example a tx queue
[ STA1 | STA2 | STA1 | STA2 ]
can result in the tx status reports
[ STA1 | STA1 | STA2 | STA2 ]
when the hw decides to put the frames for STA1 in one AMPDU.
To mitigate this effect associate the currently processed tx status
to the first frame in the tx queue with a matching wcid.
This patch fixes several problems related to incorrect tx status
reporting. Furthermore the tx rate selection is much more stable when
communicating with multiple STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit db36f79237
since I'm going to use the data pointer that was removed in
a follow up patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware returned VHT cap has the same format that cfg80211
expects. There is no need to parse the vht cap from the firmware
and then set it to ieee80211_sta_vht_cap. Just copying is
sufficient.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
curr_cmd points to the command that is in processing or waiting
for its command response from firmware. If the function shutdown
happens to occur at this time we should cancel the cmd timer and
put the command back to free queue.
Cc: <stable@vger.kernel.org> # 3.8
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During rmmod mwifiex_sdio processing FUNC_SHUTDOWN command is
sent to firmware. Firmware expcets only FUNC_INIT once WLAN
function is shut down.
Any command pending in the command queue should be ignored and
freed.
Cc: <stable@vger.kernel.org> # 3.8
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running the following script repeatedly on XO-4 with SD8787
produces command timeout and system lockup.
insmod mwifiex_sdio.ko
sleep 1
ifconfig eth0 up
iwlist eth0 scan &
sleep 0.5
rmmod mwifiex_sdio
mwifiex_send_cmd_async() is called for sync as well as async
commands. (mwifiex_send_cmd_sync() internally calls it for
sync command.)
"adapter->cmd_queued" gets filled inside mwifiex_send_cmd_async()
routine for both types of commands. But it is used only for sync
commands in mwifiex_wait_queue_complete(). This could lead to a
race when two threads try to queue a sync command with another
sync/async command simultaneously.
Get rid of global variable and pass command node as a parameter
to mwifiex_wait_queue_complete() to fix the problem.
Cc: <stable@vger.kernel.org> # 3.8
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon and multicast-buffer queues are managed by the beacon
tasklet, and the generic tx path hang check does not help in any way
here. Running it on those queues anyway can introduce some race
conditions leading to unnecessary chip resets.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 'ath9k_hw: fix calibration issues on chainmask that don't
include chain 0' changed the hardware chainmask to the chip chainmask
for the duration of the calibration, but the revert to user
configuration in the reset path runs too early.
That causes some issues with limiting the number of antennas (including
spurious failure in hardware-generated packets).
Fix this by reverting the chainmask after the essential parts of the
calibration that need the workaround, and before NF calibration is run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
max_tp_rate2 and max_prob_rate tend to get used occasionally during
retransmission, which is more useful for the statistics than probing
with individual probe packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Slow rates that have >95% success probability do not need to be
monitored continuously. When the channel conditions change rapidly, the
slow sampling results are useless anyway. When conditions change slowly,
they will be monitored by gradual downgrading of the actively used
rates. This patch slightly improves throughput under good conditions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Under load, otherwise stable rates can easily fluctuate because of
collisions. In my tests on a clean channel, the success probability of
the max throughput rate often stays somewhere between 90% and 100% under
load. This can cause some unnecessary switching to lower rates.
This patch improves stability by treating success probability values
between 90% and 100% the same.
In my tests on a 3x3 HT20 link with lots of TCP traffic, it improves the
average throughput by a few mbit/s.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This basically reverts commit b207cdb07f.
Now is possible to use drv_{add,remove}_interface() and vif->debugfs_dir
to create/remove per interface debugfs files. Remove redundant
callbacks.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is need create driver own per interface debugfs files. This is
currently done by drv_{add,remove}_interface_debugfs() callbacks. But it
is possible that after we remove interface from the driver (i.e.
on suspend) we call drv_remove_interface_debugfs() function. Fixing this
problem will require to add call drv_{add,remove}_interface_debugfs()
anytime we create and remove interface in mac80211. So it's better to
add debugfs dir dentry to vif structure to allow to create/remove
custom debugfs driver files on drv_{add,remove}_interface().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only valid mgmt response to these pairing related commands is a
mgmt_cmd_complete and the returned parameters should contain the address
and address type of the remote device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Instead of passing the bdaddr and bdaddr_type as separate parameters to
user_pairing_resp it's simpler to just pass the original mgmt_addr_info
struct which contains both values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When powering on or enabling page scan we need to ensure that the page
scan parameters are as they should be. This is because some controllers
do not properly reset these values upon HCI_Reset. Since the
write_scan_parameters function is now called from several new places it
also checks for the >= 1.2 HCI version requirement before sending the
commands.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Now that the current page scan parameters are stored in struct hci_dev
we should check against those values before sending new HCI commands to
change them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The page scan parameters (interval, window and type) stored in struct
hci_dev should not only be updated after successful reads but also after
successful writes. This patch adds the necessary handlers for the write
command complete events and updates the stored values through them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
These parameters are related to the "fast connectable" mode that can be
changed through the mgmt interface. Not all controllers properly reset
these values with HCI_Reset so they need to be read in order to be able
to verify whether the values are correct or not before enabling page
scan.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When the connectable setting is disabled the fast connectable setting
must also be disabled. This is so that we're consistent with the
pre-requisites for enabling fast connectable, one of which is that the
connectable setting is enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch refactors the fast connectable HCI commands into their own
HCI function. This is necessary so that the same function can be reused
fo the fast connectable change required by disabling the connectable
setting.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to be able to represent fast connectable mode in the mgmt
settings we need to have a HCI dev flag for it. This patch adds the flag
and makes sure its value is changed whenever a mgmt_set_fast_connectable
command completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If there's another pending mgmt_set_fast_connectable command we should
return a "busy" error response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The HCI commands that are necessary for fast connectable mode are only
available from HCI specification version 1.2 onwards. This should be
reflected in the supported settings as well as error response for the
set_fast_connectable command when dealing with a < 1.2 capable
controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The mgmt_set_fast_connectable response should be sent only when all
related HCI commands have completed. This patch fixes the issue by using
an async request and sending the response to user space throught the
complete callback of the request. The patch also fixes in the same go
the return parameters of the command which should be the current
settings.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch changes the mgmt_set_connectable handler to use an async
request for sending the required HCI command. This is necessary
preparation for handling the fast connectable change that needs to be
associated with disabling the connectable setting.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If user space attempts to set the local name to the same value that's
already set we should simply return a direct command complete for this
mgmt command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch fixes the mgmt_set_local_name command to send the appropriate
HCI commands based on BR/EDR support and LE support. Local name and EIR
data should only be sent for BR/EDR capable controllers whereas an
update to the AD should only happen for LE capable controllers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
For proper control of the AD update and the related HCI commands it's
best to run the AD update through an async request instead of a
standalone HCI command. This patch changes the hci_update_ad() function
to take a request pointer and updates its users appropriately. E.g. the
function is no longer called after the init sequence but during stage 3
of the init sequence.
The TX power is read during the init sequence, so we don't need an
explicit update whenever it is read and the AD update based on the local
name should be done through the local name mgmt handler. The only other
user is the update based on enabling advertising. This part is still
kept as there is no mgmt API to enable it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We shouldn't respond to the mgmt_set_local_name command until all
related HCI commands have completed. This patch fixes the issue by
running the local name HCI command and the EIR update in the same
asynchronous request, and returning the mgmt command complete through
the complete callback of the request.
The downside of this is that we must set hdev->dev_name before the local
name HCI command has completed since otherwise the generated EIR
command doesn't contain the new name. This means that we can no-longer
reliably detect when the name has really changed and when not. Luckily
this only affects scenarios where the mgmt interface is *not* used (e.g.
hciconfig) so redundant mgmt_ev_local_name_changed events in these cases
are an acceptable drawback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When powering off the device the hdev->flags and hdev->dev_flags need to
be cleared before calling mgmt_powered(). If this is not done the
resulting events sent to user space may contain incorrect values.
Note that the HCI_AUTO_OFF flag accessed right after this is part of the
persistent flags, so it's unchanged by the hdev->dev_flags reset.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When hci_dev_do_close() is called we should make sure to clear all
non-persistent flags in hci->dev_flags.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We'll need to use this mask also when powering off the HCI device
so it's better to have this in a single and visible place.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Now that class related operations are tracked through asynchronous HCI
requests this flag is no longer needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We should only return a mgmt command complete once all HCI commands to a
mgmt_set_dev_class or mgmt_add/remove_uuid command have completed. This
patch fixes the issue by having a proper async request complete callback
for these actions and responding to user space in the callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The add/remove_uuid and set_dev_class mgmt commands can trigger both EIR
and class HCI commands, so testing just for a pending class command is
enough. The simplest way to monitor conflicts that should trigger "busy"
error returns is to check for any pending mgmt command that can trigger
these HCI commands. This patch adds a helper function for this
(pending_eir_or_class) and uses it instead of the old HCI_PENDING_CLASS
flag to test for busy conditions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We should only notify user space that the adapter has been powered on
after all HCI commands related to the action have completed. This patch
fixes the issue by instating an async request complete callback for
these HCI commands and only notifies user space in the callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
