fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default the RFCOMM layer would still use L2CAP basic mode. For testing
purposes this option enables RFCOMM to select enhanced retransmission
mode.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
SendRRorRNR needs to acknowledge received I-frames (actually every packet
needs to acknowledge received I-frames by sending the proper packet
sequence number), so ReqSeq is set to the next I-frame number sequence to
be pulled by the reassembly function.
SendRRorRNR tells the remote side about local busy conditions, it sends
a Receiver Ready frame if local busy is false or a Receiver Not Ready
if local busy is true.
ReqSeq is the packet's field to send the number of the acknowledged
packets.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RejActioned is used to prevent retransmission when a entity is on the
WAIT_F state, i.e., waiting for a frame with F-bit set due local busy
condition or a expired retransmission timer. (When these two events raise
they send a frame with the Poll bit set and enters in the WAIT_F state to
wait for a frame with the Final bit set.)
The local entity doesn't send I-frames(the data frames) until the receipt
of a frame with F-bit set. When that happens it also set RejActioned to false.
RejActioned is a mandatory feature of ERTM spec.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As specified by ERTM spec an ERTM channel can acknowledge received
I-frames(the data frames) by sending an I-frame with the proper ReqSeq
value (i.e. ReqSeq is set to BufferSeq). Until now we aren't setting the
ReqSeq value on I-frame control bits. That way we can save sending
S-frames(Supervise frames) only to acknowledge receipt of I-frames. It
is very helpful to the full-duplex channel.
ReqSeq is the packet sequence number sent in an acknowledgement frame to
acknowledge receipt of frames up to (ReqSeq - 1).
BufferSeq controls the receiver buffer, it is used to delay
acknowledgement of new frames to not cause buffer overflow. BufferSeq
value is not increased until frames are pulled by reassembly function.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
SrejActioned is a flag that when set prevents local side to retransmit a
I-frame(the data frame) already retransmitted. The local entity can
retransmit again only when it receives a SREJ frame with the F-bit set.
SREJ frame - Selective Reject frame - is sent when an entity wants the
retransmission of a specific I-frame that was lost or corrupted.
This bug can put ERTM in an unknown state once the entity can't
retransmit.
A frame with the Final bit set is expected when the local side sends a
frame with the Poll bit set due to a local busy condition or a
retransmission timer expired. (Receipt of P-bit shall always be replied by
a frame with the F-bit set).
pi->conn_state keeps informations about many ERTM flags including
SrejActioned.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix ERTM's full-duplex channel to work as specified by ERTM spec. ERTM
needs to handle state vars, timers and counters to send and receive
I-frames(the data frames), i.e., for both sides of data communication.
We initialize all of them to the default values here.
Full-duplex channel is a mandatory feature of ERTM spec.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to BNEP test specification the proper response should be sent
for a setup connection request message after the BNEP connection setup
has been completed.
Signed-off-by: Vikram Kandukuri <vikram.kandukuri@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The tasklet schedule function helpers are just an obfuscation. So remove
them and call the schedule functions directly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For future simplification it is important that the hci_recv_frame
function is no longer an inline function. So move it into the module
itself and export it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending commands to a down interface results in a timeout while clearly
it should just return ENETDOWN. When using the ioctls this works fine,
but not when using the HCI sockets sendmsg interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement raw output callback which is used by hidraw to send raw data to
the underlying device.
Without this patch, the userspace hidraw-based applications can't send
output reports to HID Bluetooth devices.
Reported-and-tested-by: Brian Gunn <bgunn@solekai.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic Mode is the default mode of operation of a L2CAP entity. In
this case the RFC (Retransmission and Flow Control) configuration
option should not be used at all.
Normally remote L2CAP implementation should just ignore this option,
but it can cause various side effects with other Bluetooth stacks
that are not capable of handling unknown options.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The default mode for SOCK_SEQPACKET is Basic Mode. So when no
mode has been specified, Basic Mode shall be used.
This is important for current application to keep working as
expected and not cause a regression.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes double pairing issues with Secure Simple
Paring support. It was observed that when pairing with SSP
enabled, that the confirmation will be asked twice.
http://www.spinics.net/lists/linux-bluetooth/msg02473.html
This also causes bug when initiating SSP connection from
Windows Vista.
The reason is because bluetoothd does not store link keys
since HCIGETAUTHINFO returns 0. Setting default to general
bonding fixes these issues.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before calling capable(CAP_NET_RAW) check if this operations is on behalf
of the kernel or on behalf of userspace. Do not do the security check if
it is on behalf of the kernel.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic __sock_create function has a kern argument which allows the
security system to make decisions based on if a socket is being created by
the kernel or by userspace. This patch passes that flag to the
net_proto_family specific create function, so it can do the same thing.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new socket level option to report number of queue overflows
Recently I augmented the AF_PACKET protocol to report the number of frames lost
on the socket receive queue between any two enqueued frames. This value was
exported via a SOL_PACKET level cmsg. AFter I completed that work it was
requested that this feature be generalized so that any datagram oriented socket
could make use of this option. As such I've created this patch, It creates a
new SOL_SOCKET level option called SO_RXQ_OVFL, which when enabled exports a
SOL_SOCKET level cmsg that reports the nubmer of times the sk_receive_queue
overflowed between any two given frames. It also augments the AF_PACKET
protocol to take advantage of this new feature (as it previously did not touch
sk->sk_drops, which this patch uses to record the overflow count). Tested
successfully by me.
Notes:
1) Unlike my previous patch, this patch simply records the sk_drops value, which
is not a number of drops between packets, but rather a total number of drops.
Deltas must be computed in user space.
2) While this patch currently works with datagram oriented protocols, it will
also be accepted by non-datagram oriented protocols. I'm not sure if thats
agreeable to everyone, but my argument in favor of doing so is that, for those
protocols which aren't applicable to this option, sk_drops will always be zero,
and reporting no drops on a receive queue that isn't used for those
non-participating protocols seems reasonable to me. This also saves us having
to code in a per-protocol opt in mechanism.
3) This applies cleanly to net-next assuming that commit
977750076d (my af packet cmsg patch) is reverted
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All usages of structure net_proto_ops should be declared const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.
Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.
Signed-off-by: David S. Miller <davem@davemloft.net>
HID core registers input, hidraw and hiddev devices, but leaves
unregistering it up to the individual driver, which is not really nice.
Let's move all the logic to the core.
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Brian Rogers <brian@xyzw.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When called, 'Send RRorRNR' should send a RNR frame if local device is
busy or a RR frame otherwise.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement all issues related to RemoteBusy in the RECV state table.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement the Recv ReqSeqAndFBit event when a RR frame with F bit set is
received.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Simplify more conversions to the right endian with the proper helpers.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Avoid race conditions when accessing the L2CAP socket from within the
timeout handlers.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using DEFER_SETUP on a RFCOMM socket, a SABM frame triggers
authorization which when rejected send a DM response. This is fine
according to the RFCOMM spec:
the responding implementation may replace the "proper" response
on the Multiplexer Control channel with a DM frame, sent on the
referenced DLCI to indicate that the DLCI is not open, and that
the responder would not grant a request to open it later either.
But some stacks doesn't seems to cope with this leaving DLCI 0 open after
receiving DM frame.
To fix it properly a timer was introduced to rfcomm_session which is used
to set a timeout when the last active DLC of a session is unlinked, this
will give the remote stack some time to reply with a proper DISC frame on
DLCI 0 avoiding both sides sending DISC to each other on stacks that
follow the specification and taking care of those who don't by taking
down DLCI 0.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Support for receiving of SREJ frames as specified by the state table.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When L2CAP loses an I-frame we send a SREJ frame to the transmitter side
requesting the lost packet. This patch implement all Recv I-frame events
on SREJ_SENT state table except the ones that deal with SendRej (the REJ
exception at receiver side is yet not implemented).
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement CRC16 check for L2CAP packets. FCS is used by Streaming Mode and
Enhanced Retransmission Mode and is a extra check for the packet content.
Using CRC16 is the default, L2CAP won't use FCS only when both side send
a "No FCS" request.
Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Streaming Mode is helpful for the Bluetooth streaming based profiles, such
as A2DP. It doesn't have any error control or flow control.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
L2CAP uses retransmission and monitor timers to inquiry the other side
about unacked I-frames. After sending each I-frame we (re)start the
retransmission timer. If it expires, we start a monitor timer that send a
S-frame with P bit set and wait for S-frame with F bit set. If monitor
timer expires, try again, at a maximum of L2CAP_DEFAULT_MAX_TX.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving an I-frame with unexpected txSeq, receiver side start the
recovery procedure by sending a REJ S-frame to the transmitter side. So
the transmitter can re-send the lost I-frame.
This patch just adds a basic support for retransmission, it doesn't
mean that ERTM now has full support for packet retransmission.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ERTM should use Segmentation and Reassembly to break down a SDU in many
PDUs on sending data to the other side.
On sending packets we queue all 'segments' until end of segmentation and
just the add them to the queue for sending. On receiving we create a new
SKB with the SDU reassembled.
Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for ERTM transfers, without retransmission, with
txWindow up to 63 and with acknowledgement of packets received. Now the
packets are queued before call l2cap_do_send(), so packets couldn't be
sent at the time we call l2cap_sock_sendmsg(). They will be sent in
an asynchronous way on later calls of l2cap_ertm_send(). Besides if an
error occurs on calling l2cap_do_send() we disconnect the channel.
Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The code for sending a disconnect request was repeated several times
within L2CAP source code. So move this into its own function.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to config_req and config_rsp to configure ERTM and Streaming
mode. If the remote device specifies ERTM or Streaming mode, then the
same mode is proposed. Otherwise ERTM or Basic mode is used. And in case
of a state 2 device, the remote device should propose the same mode. If
not, then the channel gets disconnected.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When trying to establish a connection with Enhanced Retransmission mode
enabled, the RFC option needs to be added to the configuration.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To enable Enhanced Retransmission mode it needs to be set via a socket
option. A different mode can be set on a socket, but on listen() and
connect() the mode is checked and ERTM is only allowed if it is enabled
via the module parameter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the Enhanced Retransmission mode for L2CAP is still under heavy
development disable it by default and provide a module option to enable
it manually for testing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The rfcomm_init bug fix went into the kernel premature before it got fully
reviewed and acknowledged by the Bluetooth maintainer. So fix up the coding
style now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hdev->req_lock is used as mutex so make it a mutex.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The core exports the hci_conn_hold_device() and hci_conn_put_device()
functions for device reference of connections. Use this to ensure that
the uevents from the parent are send after the child ones.
Based on a report by Brian Rogers <brian@xyzw.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device model itself has no real usable reference counting at the
moment and this causes problems if parents are deleted before their
children. The device model itself handles the memory details of this
correctly, but the uevent order is not consistent. This causes various
problems for systems like HAL or even X.
So until device_put() does a proper cleanup, the device for Bluetooth
connection will be protected with an extra reference counting to ensure
the correct order of uevents when connections are terminated.
This is not an automatic feature. Higher Bluetooth layers like HIDP or
BNEP should grab this new reference to ensure that their uevents are
send before the ones from the parent device.
Based on a report by Brian Rogers <brian@xyzw.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the HID subsystem will create HIDRAW devices for the transport
driver, but it will not disconnect them. Until the HID subsytem gets
fixed, ensure that HIDRAW and HIDDEV devices are disconnected when the
Bluetooth HID device gets removed.
Based on a patch from Brian Rogers <brian@xyzw.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a test case in PTS tool; PTS will send the VIRTUAL_CABLE_UNPLUG
command to IUT. Then IUT should disconnect the channel and kill the HID
session when it receives the command. The VIRTUAL_CABLE_UNPLUG command
is parsed by HID transport, but it is not scheduled to do so. Add a
call to hidp_schedule() to kill the session.
Signed-off-by: Jothikumar Mothilal <jothikumar.mothilal@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SCO sockets for Bluetooth audio setup and streaming are missing the
shutdown implementation. This hasn't been a problem so far, but with a
more deeper integration with PulseAudio it is important to shutdown SCO
sockets properly.
Also the Headset profile 1.2 has more detailed qualification tests that
require that SCO and RFCOMM channels are terminated in the right order. A
proper shutdown function is necessary for this.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johan Hedberg <johan.hedberg@nokia.com>
String literals are constant, and usually, we can also tag the array
of pointers const too, moving it to the .rodata section.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rfcomm tty may be used before rfcomm_tty_driver initilized,
The problem is that now socket layer init before tty layer, if userspace
program do socket callback right here then oops will happen.
reporting in:
http://marc.info/?l=linux-bluetooth&m=124404919324542&w=2
make 3 changes:
1. remove #ifdef in rfcomm/core.c,
make it blank function when rfcomm tty not selected in rfcomm.h
2. tune the rfcomm_init error patch to ensure
tty driver initilized before rfcomm socket usage.
3. remove __exit for rfcomm_cleanup_sockets
because above change need call it in a __init function.
Reported-by: Oliver Hartkopp <oliver@hartkopp.net>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
changed initial sk_wmem_alloc value.
We need to take into account this offset when reporting
sk_wmem_alloc to user, in PROC_FS files or various
ioctls (SIOCOUTQ/TIOCOUTQ)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the re-write of the RFKILL subsystem it is no longer good to just
select RFKILL, but it is important to add a proper depends on rule.
Based on a report by Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the re-write of the RFKILL subsystem it is now possible to easily
integrate RFKILL soft-switch support into the Bluetooth subsystem. All
Bluetooth devices will now get automatically RFKILL support.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth source uses some endian conversion helpers, that in the end
translate to kernel standard routines. So remove this obfuscation since it
is fully pointless.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds the basic constants required to add support for L2CAP Enhanced
Retransmission feature.
Based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the errors without changing the l2cap.o binary:
text data bss dec hex filename
18059 568 0 18627 48c3 l2cap.o.after
18059 568 0 18627 48c3 l2cap.o.before
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The initial value of err is not used until it is set to -ENOMEM. So just
remove the initialization completely.
Based on a patch from Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using the L2CAP_CONF_HINT macro is easier to understand than using a
hardcoded 0x80 value.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use macros instead of hardcoded numbers to make the L2CAP source code
more readable.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change the name of the Kernel CAPI exported function capi_ctr_reseted()
to something representing its purpose better.
Impact: renaming, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calls to flush_work() are pointless in a single thread workqueue
and they are actually causing a lockdep warning.
=============================================
[ INFO: possible recursive locking detected ]
2.6.30-rc6-02911-gbb803cf #16
---------------------------------------------
bluetooth/2518 is trying to acquire lock:
(bluetooth){+.+.+.}, at: [<c0130c14>] flush_work+0x28/0xb0
but task is already holding lock:
(bluetooth){+.+.+.}, at: [<c0130424>] worker_thread+0x149/0x25e
other info that might help us debug this:
2 locks held by bluetooth/2518:
#0: (bluetooth){+.+.+.}, at: [<c0130424>] worker_thread+0x149/0x25e
#1: (&conn->work_del){+.+...}, at: [<c0130424>] worker_thread+0x149/0x25e
stack backtrace:
Pid: 2518, comm: bluetooth Not tainted 2.6.30-rc6-02911-gbb803cf #16
Call Trace:
[<c03d64d9>] ? printk+0xf/0x11
[<c0140d96>] __lock_acquire+0x7ce/0xb1b
[<c0141173>] lock_acquire+0x90/0xad
[<c0130c14>] ? flush_work+0x28/0xb0
[<c0130c2e>] flush_work+0x42/0xb0
[<c0130c14>] ? flush_work+0x28/0xb0
[<f8b84966>] del_conn+0x1c/0x84 [bluetooth]
[<c0130469>] worker_thread+0x18e/0x25e
[<c0130424>] ? worker_thread+0x149/0x25e
[<f8b8494a>] ? del_conn+0x0/0x84 [bluetooth]
[<c0133843>] ? autoremove_wake_function+0x0/0x33
[<c01302db>] ? worker_thread+0x0/0x25e
[<c013355a>] kthread+0x45/0x6b
[<c0133515>] ? kthread+0x0/0x6b
[<c01034a7>] kernel_thread_helper+0x7/0x10
Based on a report by Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A remote device in security mode 3 that tries to connect will require
the pairing during the connection setup phase. The disconnect timeout
is now triggered within 10 milliseconds and causes the pairing to fail.
If a connection is not fully established and a PIN code request is
received, don't trigger the disconnect timeout. The either successful
or failing connection complete event will make sure that the timeout
is triggered at the right time.
The biggest problem with security mode 3 is that many Bluetooth 2.0
device and before use a temporary security mode 3 for dedicated
bonding.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johan Hedberg <johan.hedberg@nokia.com>
The connection setup phase takes around 2 seconds or longer and in
that time it is possible that the need for an ACL connection is no
longer present. If that happens then, the connection attempt will
be canceled.
This only applies to outgoing connections, but currently it can also
be triggered by incoming connection. Don't call hci_acl_connect_cancel()
on incoming connection since these have to be either accepted or rejected
in this state. Once they are successfully connected they need to be
fully disconnected anyway.
Also remove the wrong hci_acl_disconn() call for SCO and eSCO links
since at this stage they can't be disconnected either, because the
connection handle is still unknown.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johan Hedberg <johan.hedberg@nokia.com>
The module refcount is increased by hci_dev_hold() call in hci_conn_add()
and decreased by hci_dev_put() call in del_conn(). In case the connection
setup fails, hci_dev_put() is never called.
Procedure to reproduce the issue:
# hciconfig hci0 up
# lsmod | grep btusb -> "used by" refcount = 1
# hcitool cc <non-exisiting bdaddr> -> will get timeout
# lsmod | grep btusb -> "used by" refcount = 2
# hciconfig hci0 down
# lsmod | grep btusb -> "used by" refcount = 1
# rmmod btusb -> ERROR: Module btusb is in use
The hci_dev_put() call got moved into del_conn() with the 2.6.25 kernel
to fix an issue with hci_dev going away before hci_conn. However that
change was wrong and introduced this problem.
When calling hci_conn_del() it has to call hci_dev_put() after freeing
the connection details. This handling should be fully symmetric. The
execution of del_conn() is done in a work queue and needs it own calls
to hci_dev_hold() and hci_dev_put() to ensure that the hci_dev stays
until the connection cleanup has been finished.
Based on a report by Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Bing Zhao <bzhao@marvell.com>
Due to a semantic changes in flush_workqueue() the current approach of
synchronizing the sysfs handling for connections doesn't work anymore. The
whole approach is actually fully broken and based on assumptions that are
no longer valid.
With the introduction of Simple Pairing support, the creation of low-level
ACL links got changed. This change invalidates the reason why in the past
two independent work queues have been used for adding/removing sysfs
devices. The adding of the actual sysfs device is now postponed until the
host controller successfully assigns an unique handle to that link. So
the real synchronization happens inside the controller and not the host.
The only left-over problem is that some internals of the sysfs device
handling are not initialized ahead of time. This leaves potential access
to invalid data and can cause various NULL pointer dereferences. To fix
this a new function makes sure that all sysfs details are initialized
when an connection attempt is made. The actual sysfs device is only
registered when the connection has been successfully established. To
avoid a race condition with the registration, the check if a device is
registered has been moved into the removal work.
As an extra protection two flush_work() calls are left in place to
make sure a previous add/del work has been completed first.
Based on a report by Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Roger Quadros <ext-roger.quadros@nokia.com>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
The Bluetooth 2.1 specification introduced four different security modes
that can be mapped using Legacy Pairing and Simple Pairing. With the
usage of Simple Pairing it is required that all connections (except
the ones for SDP) are encrypted. So even the low security requirement
mandates an encrypted connection when using Simple Pairing. When using
Legacy Pairing (for Bluetooth 2.0 devices and older) this is not required
since it causes interoperability issues.
To support this properly the low security requirement translates into
different host controller transactions depending if Simple Pairing is
supported or not. However in case of Simple Pairing the command to
switch on encryption after a successful authentication is not triggered
for the low security mode. This patch fixes this and actually makes
the logic to differentiate between Simple Pairing and Legacy Pairing
a lot simpler.
Based on a report by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth stack uses a reference counting for all established ACL
links and if no user (L2CAP connection) is present, the link will be
terminated to save power. The problem part is the dedicated pairing
when using Legacy Pairing (Bluetooth 2.0 and before). At that point
no user is present and pairing attempts will be disconnected within
10 seconds or less. In previous kernel version this was not a problem
since the disconnect timeout wasn't triggered on incoming connections
for the first time. However this caused issues with broken host stacks
that kept the connections around after dedicated pairing. When the
support for Simple Pairing got added, the link establishment procedure
needed to be changed and now causes issues when using Legacy Pairing
When using Simple Pairing it is possible to do a proper reference
counting of ACL link users. With Legacy Pairing this is not possible
since the specification is unclear in some areas and too many broken
Bluetooth devices have already been deployed. So instead of trying to
deal with all the broken devices, a special pairing timeout will be
introduced that increases the timeout to 60 seconds when pairing is
triggered.
If a broken devices now puts the stack into an unforeseen state, the
worst that happens is the disconnect timeout triggers after 120 seconds
instead of 4 seconds. This allows successful pairings with legacy and
broken devices now.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom chips with 2.1 firmware handle the fallback case to a SCO
link wrongly when setting up eSCO connections.
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
handle 11 voice setting 0x0060
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 1 bdaddr 00:1E:3A:xx:xx:xx type SCO encrypt 0x01
The Link Manager negotiates the fallback to SCO, but then sends out
a Connect Complete event. This is wrong and the Link Manager should
actually send a Synchronous Connection Complete event if the Setup
Synchronous Connection has been used. Only the remote side is allowed
to use Connect Complete to indicate the missing support for eSCO in
the host stack.
This patch adds a workaround for this which clearly should not be
needed, but reality is that broken Broadcom devices are deployed.
Based on a report by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtman <marcel@holtmann.org>
Some Bluetooth chips (like the ones from Texas Instruments) don't do
proper eSCO negotiations inside the Link Manager. They just return an
error code and in case of the Kyocera ED-8800 headset it is just a
random error.
< HCI Command: Setup Synchronous Connection 0x01|0x0028) plen 17
handle 1 voice setting 0x0060
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
status 0x1f handle 257 bdaddr 00:14:0A:xx:xx:xx type eSCO
Error: Unspecified Error
In these cases it is up to the host stack to fallback to a SCO setup
and so retry with SCO parameters.
Based on a report by Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a missing call to rfcomm_dlc_clear_timer in the case that
DEFER_SETUP is used and so the connection gets disconnected after the
timeout even if it was successfully accepted previously.
This patch adds a call to rfcomm_dlc_clear_timer to rfcomm_dlc_accept
which will get called when the user accepts the connection by calling
read() on the socket.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
struct tty_operations::proc_fops took it's place and there is one less
create_proc_read_entry() user now!
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dpm_list currently relies on the fact that child devices will
be registered after their parents to get a correct suspend
order. Using device_move() however destroys this assumption, as
an already registered device may be moved under a newly registered
one.
This patch adds a new argument to device_move(), allowing callers
to specify how dpm_list should be adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Userspace pairing code can be simplified if it doesn't have to fall
back to using L2CAP_LM in the case of L2CAP raw sockets. This patch
allows the BT_SECURITY socket option to be used for these sockets.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The CID value of L2CAP sockets need to be set to zero. All userspace
applications do this via memset() on the sockaddr_l2 structure. The
RFCOMM implementation uses in-kernel L2CAP sockets and so it has to
make sure that l2_cid is set to zero.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the future the L2CAP layer will have full support for fixed channels
and right now it already can export the channel assignment, but for the
functions bind() and connect() the usage of only CID 0 is allowed. This
allows an easy detection if the kernel supports fixed channels or not,
because otherwise it would impossible for application to tell.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When BT_DEFER_SETUP is enabled on a RFCOMM socket, then switch its
current state from BT_OPEN to BT_CONNECT2. This gives the Bluetooth
core a unified way to handle L2CAP and RFCOMM sockets. The BT_CONNECT2
state is designated for incoming connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When BT_DEFER_SETUP has been enabled on a Bluetooth socket it keeps
signaling POLLIN all the time. This is a wrong behavior. The POLLIN
should only be signaled if the client socket is in BT_CONNECT2 state
and the parent has been BT_DEFER_SETUP enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The authentication requirement got only updated when the security level
increased. This is a wrong behavior. The authentication requirement is
read by the Bluetooth daemon to make proper decisions when handling the
IO capabilities exchange. So set the value that is currently expected by
the higher layers like L2CAP and RFCOMM.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP layer can trigger the authentication via an ACL connection or
later on to increase the security level. When increasing the security
level it didn't use the same authentication requirements when triggering
a new ACL connection. Make sure that exactly the same authentication
requirements are used. The only exception here are the L2CAP raw sockets
which are only used for dedicated bonding.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some of the qualification tests demand that in case of failures in L2CAP
the HCI disconnect should indicate a reason why L2CAP fails. This is a
bluntly layer violation since multiple L2CAP connections could be using
the same ACL and thus forcing a disconnect reason is not a good idea.
To comply with the Bluetooth test specification, the disconnect reason
is now stored in the L2CAP connection structure and every time a new
L2CAP channel is added it will set back to its default. So only in the
case where the L2CAP channel with the disconnect reason is really the
last one, it will propagated to the HCI layer.
The HCI layer has been extended with a disconnect indication that allows
it to ask upper layers for a disconnect reason. The upper layer must not
support this callback and in that case it will nicely default to the
existing behavior. If an upper layer like L2CAP can provide a disconnect
reason that one will be used to disconnect the ACL or SCO link.
No modification to the ACL disconnect timeout have been made. So in case
of Linux to Linux connection the initiator will disconnect the ACL link
before the acceptor side can signal the specific disconnect reason. That
is perfectly fine since Linux doesn't make use of this value anyway. The
L2CAP layer has a perfect valid error code for rejecting connection due
to a security violation. It is unclear why the Bluetooth specification
insists on having specific HCI disconnect reason.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation for L2CAP fixed channel support, the CID value of a
L2CAP connection needs to be accessible via the socket interface. The
CID is the connection identifier and exists as source and destination
value. So extend the L2CAP socket address structure with this field and
change getsockname() and getpeername() to fill it in.
The bind() and connect() functions have been modified to handle L2CAP
socket address structures of variable sizes. This makes them future
proof if additional fields need to be added.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the extended features mask indicates support for fixed channels,
request the list of available fixed channels. This also enables the
fixed channel features bit so remote implementations can request
information about it. Currently only the signal channel will be
listed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The recommendation for the L2CAP PSM 1 (SDP) is to not use any kind
of authentication or encryption. So don't trigger authentication
for incoming and outgoing SDP connections.
For L2CAP PSM 3 (RFCOMM) there is no clear requirement, but with
Bluetooth 2.1 the initiator is required to enable authentication
and encryption first and this gets enforced. So there is no need
to trigger an additional authentication step. The RFCOMM service
security will make sure that a secure enough link key is present.
When the encryption gets enabled after the SDP connection setup,
then switch the security level from SDP to low security.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the remote L2CAP server uses authentication pending stage and
encryption is enabled it can happen that a L2CAP connection request is
sent twice due to a race condition in the connection state machine.
When the remote side indicates any kind of connection pending, then
track this state and skip sending of L2CAP commands for this period.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When two L2CAP connections are requested quickly after the ACL link has
been established there exists a window for a race condition where a
connection request is sent before the information response has been
received. Any connection request should only be sent after an exchange
of the extended features mask has been finished.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When no authentication requirements are selected, but an outgoing or
incoming connection has requested any kind of security enforcement,
then set these authentication requirements.
This ensures that the userspace always gets informed about the
authentication requirements (if available). Only when no security
enforcement has happened, the kernel will signal invalid requirements.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving incoming connection to specific services, always use
general bonding. This ensures that the link key gets stored and can be
used for further authentications.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When attempting to setup eSCO connections it can happen that some link
manager implementations fail to properly negotiate the eSCO parameters
and thus fail the eSCO setup. Normally the link manager is responsible
for the negotiation of the parameters and actually fallback to SCO if
no agreement can be reached. In cases where the link manager is just too
stupid, then at least try to establish a SCO link if eSCO fails.
For the Bluetooth devices with EDR support this includes handling packet
types of EDR basebands. This is particular tricky since for the EDR the
logic of enabling/disabling one specific packet type is turned around.
This fix contains an extra bitmask to disable eSCO EDR packet when
trying to fallback to a SCO connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For L2CAP sockets with medium and high security requirement a missing
encryption will enforce the closing of the link. For the L2CAP raw
sockets this is not needed, so skip that check.
This fixes a crash when pairing Bluetooth 2.0 (and earlier) devices
since the L2CAP state machine got confused and then locked up the whole
system.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During a role change with pre-Bluetooth 2.1 devices, the remote side drops
the encryption of the RFCOMM connection. We allow a grace period for the
encryption to be re-established, before dropping the connection. During
this grace period, the RFCOMM_SEC_PENDING flag is set. Check this flag
before sending RFCOMM packets.
Signed-off-by: Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Due to lockdep changes, the CONFIG_DEBUG_LOCK_ALLOC ifdef is not needed
now. So just remove it here.
The following commit fixed the !lockdep build warnings:
commit e8f6fbf62d
Author: Ingo Molnar <mingo@elte.hu>
Date: Wed Nov 12 01:38:36 2008 +0000
lockdep: include/linux/lockdep.h - fix warning in net/bluetooth/af_bluetooth.c
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the support for the enhanced security model and the support for
deferring connection setup, it is a good idea to increase various
version numbers.
This is purely cosmetic and has no effect on the behavior, but can
be really helpful when debugging problems in different kernel versions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new socket options should only be evaluated for SOL_BLUETOOTH level
and not for every other level. Previously this causes some minor issues
when detecting if a kernel with certain features is available.
Also restrict BT_SECURITY to SOCK_SEQPACKET for L2CAP and SOCK_STREAM for
the RFCOMM protocol.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For L2CAP connections with high security setting, the link will be
immediately dropped when the encryption gets disabled. For L2CAP
connections with medium security there will be grace period where
the remote device has the chance to re-enable encryption. If it
doesn't happen then the link will also be disconnected.
The requirement for the grace period with medium security comes from
Bluetooth 2.0 and earlier devices that require role switching.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A role switch with devices following the Bluetooth pre-2.1 standards
or without Encryption Pause and Resume support is not possible if
encryption is enabled. Most newer headsets require the role switch,
but also require that the connection is encrypted.
For connections with a high security mode setting, the link will be
immediately dropped. When the connection uses medium security mode
setting, then a grace period is introduced where the TX is halted and
the remote device gets a change to re-enable encryption after the
role switch. If not re-enabled the link will be dropped.
Based on initial work by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current security model is based around the flags AUTH, ENCRYPT and
SECURE. Starting with support for the Bluetooth 2.1 specification this is
no longer sufficient. The different security levels are now defined as
SDP, LOW, MEDIUM and SECURE.
Previously it was possible to set each security independently, but this
actually doesn't make a lot of sense. For Bluetooth the encryption depends
on a previous successful authentication. Also you can only update your
existing link key if you successfully created at least one before. And of
course the update of link keys without having proper encryption in place
is a security issue.
The new security levels from the Bluetooth 2.1 specification are now
used internally. All old settings are mapped to the new values and this
way it ensures that old applications still work. The only limitation
is that it is no longer possible to set authentication without also
enabling encryption. No application should have done this anyway since
this is actually a security issue. Without encryption the integrity of
the authentication can't be guaranteed.
As default for a new L2CAP or RFCOMM connection, the LOW security level
is used. The only exception here are the service discovery sessions on
PSM 1 where SDP level is used. To have similar security strength as with
a Bluetooth 2.0 and before combination key, the MEDIUM level should be
used. This is according to the Bluetooth specification. The MEDIUM level
will not require any kind of man-in-the-middle (MITM) protection. Only
the HIGH security level will require this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the remote device supports only SCO connections, on receipt of
the HCI_EV_CONN_COMPLETE event packet, the connect state is changed to
BT_CONNECTED, but the socket state is not updated. Hence, the connect()
call times out even though the SCO connection has been successfully
established.
Based on a report by Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All SCO and eSCO connection are auto-accepted no matter if there is a
corresponding listening socket for them. This patch changes this and
connection requests for SCO and eSCO without any socket are rejected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to decide if listening L2CAP sockets should be accept()ed
the BD_ADDR of the remote device needs to be known. This patch adds
a socket option which defines a timeout for deferring the actual
connection setup.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to decide if listening RFCOMM sockets should be accept()ed
the BD_ADDR of the remote device needs to be known. This patch adds
a socket option which defines a timeout for deferring the actual
connection setup.
The connection setup is done after reading from the socket for the
first time. Until then writing to the socket returns ENOTCONN.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP and RFCOMM applications require support for authorization
and the ability of rejecting incoming connection requests. The socket
interface is not really able to support this.
This patch does the ground work for a socket option to defer connection
setup. Setting this option allows calling of accept() and then the
first read() will trigger the final connection setup. Calling close()
would reject the connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The socket option levels SOL_L2CAP, SOL_RFOMM and SOL_SCO are currently
in use by various Bluetooth applications. Going forward the common
option level SOL_BLUETOOTH should be used. This patch prepares the clean
split of the old and new option levels while keeping everything backward
compatibility.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of connection failures the rfcomm_sock_sendmsg() should return
an error and not a 0 value.
Signed-off-by: Victor Shcherbatyuk <victor.shcherbatyuk@tomtom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Convert to net_device_ops and use internal net_device_stats in bnep
device.
Note: no need for bnep_net_ioctl since if ioctl is not set, then
dev_ifsioc handles it by returning -EOPNOTSUPP
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel_accept() does not hold the module refcount of newsock->ops->owner,
so we need __module_get(newsock->ops->owner) code after call kernel_accept()
by hand.
In sunrpc, the module refcount is missing to hold. So this cause kernel panic.
Used following script to reproduct:
while [ 1 ];
do
mount -t nfs4 192.168.0.19:/ /mnt
touch /mnt/file
umount /mnt
lsmod | grep ipv6
done
This patch fixed the problem by add __module_get(newsock->ops->owner) to
kernel_accept(). So we do not need to used __module_get(newsock->ops->owner)
in every place when used kernel_accept().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Stephen Rothwell points out, we don't want 'sock' here but
rather we really do want 'sk'.
This local var is protected by all sorts of bluetooth debugging
kconfig vars, but BT_DBG() is just a straight pr_debug() call
which is unconditional.
pr_debug() evaluates it's args only if either DEBUG or
CONFIG_DYNAMIC_PRINTK_DEBUG is defined.
Solving this inside of the BT_DBG() macro is non-trivial since
it's varargs. And these ifdefs are ugly.
So, just mark this 'sk' thing __maybe_unused and kill the ifdefs.
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that the following sequence of actions will reproduce the
oops:
1. Create a new RFCOMM device (using RFCOMMCREATEDEV ioctl)
2. (Try to) open the device
3. Release the RFCOMM device (using RFCOMMRELEASEDEV ioctl)
At this point, the "/dev/rfcomm*" device is still in use, but it is gone
from the internal list, so the device id can be reused.
4. Create a new RFCOMM device with the same device id as before
And now kobject will complain that the TTY already exists.
(See http://lkml.org/lkml/2008/7/13/89 for a reproducible test-case.)
This patch attempts to correct this by only removing the device from the
internal list of devices at the final unregister stage, so that the id
won't get reused until the device has been completely destructed.
This should be safe as the RFCOMM_TTY_RELEASED bit will be set for the
device and prevent the device from being reopened after it has been
released.
Based on a report from Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Newer GCC versions are a little bit picky about how to deal with format
arguments:
net/bluetooth/hci_sysfs.c: In function ‘hci_register_sysfs’:
net/bluetooth/hci_sysfs.c:418: warning: format not a string literal and no format arguments
It is simple enough to fix and makes the compiler happy.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.
As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth subsystem was not using the HCI Reset command when doing
device initialization. The Bluetooth 1.0b specification was ambiguous
on how the device firmware was suppose to handle it. Almost every device
was triggering a transport reset at the same time. In case of USB this
ended up in disconnects from the bus.
All modern Bluetooth dongles handle this perfectly fine and a lot of
them actually require that HCI Reset is sent. If not then they are
either stuck in their HID Proxy mode or their internal structures for
inquiry and paging are not correctly setup.
To handle old and new devices smoothly the Bluetooth subsystem contains
a quirk to force the HCI Reset on initialization. However maintaining
such a quirk becomes more and more complicated. This patch turns the
logic around and lets the old devices disable the HCI Reset command.
The only device where the HCI_QUIRK_NO_RESET is still needed are the
original Digianswer devices and dongles with an early CSR firmware.
CSR reported that they fixed this for version 12 firmware. The last
official release of version 11 firmware is build ID 115. The first
version 12 candidate was build ID 117.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After adding proper lockdep annotations for Bluetooth protocols the case
when lockdep is disabled produced two compiler warnings:
net/bluetooth/af_bluetooth.c:60: warning: ‘bt_key_strings’ defined but not used
net/bluetooth/af_bluetooth.c:71: warning: ‘bt_slock_key_strings’ defined but not used
Fix both of them by adding a CONFIG_DEBUG_LOCK_ALLOC conditional around
them and re-arranging the code a little bit.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
struct hci_dev_list_req {
__u16 dev_num;
struct hci_dev_req dev_req[0]; /* hci_dev_req structures */
};
sizeof(struct hci_dev_list_req) == 4, so the two bytes immediately
following "dev_num" will never be initialized. When this structure
is copied to userspace, these uninitialized bytes are leaked.
Fix by using kzalloc() instead of kmalloc(). Found using kmemcheck.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
fix this warning:
net/bluetooth/rfcomm/sock.c: In function ‘rfcomm_sock_ioctl’:
net/bluetooth/rfcomm/sock.c:795: warning: unused variable ‘sk’
perhaps BT_DEBUG() should be improved to do printf format checking
instead of the #ifdef, but that looks quite intrusive: each bluetooth
.c file undefines the macro.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move ignore quirks from usbhid-quirks into hid-core code. Also don't output
warning when ENODEV is error code in usbhid and try ordinal input in hidp
when that error is returned.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Next step for complete hid bus, this patch includes:
- call parser either from probe or from hid-core if there is no probe.
- add ll_driver structure and centralize some stuff there (open, close...)
- split and merge usb_hid_configure and hid_probe into several functions
to allow hooks/fixes between them
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make a bus from hid core. This is the first step for converting all the
quirks and separate almost-drivers into real drivers attached to this bus.
It's implemented to change behaviour in very tiny manner, so that no driver
needs to be changed this time.
Also add generic drivers for both usb and bt into usbhid or hidp
respectively which will bind all non-blacklisted device. Those blacklisted
will be either grabbed by special drivers or by nobody if they are broken at
the very rude base.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To speed up the Simple Pairing connection setup, the support for the
default link policy has been enabled. This is in contrast to settings
the link policy on every connection setup. Using the default link policy
is the preferred way since there is no need to dynamically change it for
every connection.
For backward compatibility reason and to support old userspace the
HCISETLINKPOL ioctl has been switched over to using hci_request() to
issue the HCI command for setting the default link policy instead of
just storing it in the HCI device structure.
However the hci_request() can only be issued when the device is
brought up. If used on a device that is registered, but still down
it will timeout and fail. This is problematic since the command is
put on the TX queue and the Bluetooth core tries to submit it to
hardware that is not ready yet. The timeout for these requests is
10 seconds and this causes a significant regression when setting up
a new device.
The userspace can perfectly handle a failure of the HCISETLINKPOL
ioctl and will re-submit it later, but the 10 seconds delay causes
a problem. So in case hci_request() is called on a device that is
still down, just fail it with ENETDOWN to indicate what happens.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Security Mode 4 of the Bluetooth 2.1 specification has strict
authentication and encryption requirements. It is the initiators job
to create a secure ACL link. However in case of malicious devices, the
acceptor has to make sure that the ACL is encrypted before allowing
any kind of L2CAP connection. The only exception here is the PSM 1 for
the service discovery protocol, because that is allowed to run on an
insecure ACL link.
Previously it was enough to reject a L2CAP connection during the
connection setup phase, but with Bluetooth 2.1 it is forbidden to
do any L2CAP protocol exchange on an insecure link (except SDP).
The new hci_conn_check_link_mode() function can be used to check the
integrity of an ACL link. This functions also takes care of the cases
where Security Mode 4 is disabled or one of the devices is based on
an older specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the introduction of Security Mode 4 and Simple Pairing from the
Bluetooth 2.1 specification it became mandatory that the initiator
requires authentication and encryption before any L2CAP channel can
be established. The only exception here is PSM 1 for the service
discovery protocol (SDP). It is meant to be used without any encryption
since it contains only public information. This is how Bluetooth 2.0
and before handle connections on PSM 1.
For Bluetooth 2.1 devices the pairing procedure differentiates between
no bonding, general bonding and dedicated bonding. The L2CAP layer
wrongly uses always general bonding when creating new connections, but it
should not do this for SDP connections. In this case the authentication
requirement should be no bonding and the just-works model should be used,
but in case of non-SDP connection it is required to use general bonding.
If the new connection requires man-in-the-middle (MITM) protection, it
also first wrongly creates an unauthenticated link key and then later on
requests an upgrade to an authenticated link key to provide full MITM
protection. With Simple Pairing the link key generation is an expensive
operation (compared to Bluetooth 2.0 and before) and doing this twice
during a connection setup causes a noticeable delay when establishing
a new connection. This should be avoided to not regress from the expected
Bluetooth 2.0 connection times. The authentication requirements are known
up-front and so enforce them.
To fulfill these requirements the hci_connect() function has been extended
with an authentication requirement parameter that will be stored inside
the connection information and can be retrieved by userspace at any
time. This allows the correct IO capabilities exchange and results in
the expected behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
