Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the EVGA inDtube. Both ATSC and analog side validated as
fully functional.
Thanks to Jake Crimmins from EVGA for providing the correct GPIO info.
Thanks to Alan Hagge for doing all the device testing.
Thanks to Greg Williamson for providing hardware for testing.
Cc: Jake Crimmins <jcrimmins@evga.com>
Cc: Alan Hagge <ahagge@gmail.com>
Cc: Greg Williamson <cheeseboy16@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cases where the board had a default USB ID, we would not indentify the
board until after the call to em28xx_set_mode(). As a result, for those
boards the analog GPIOs were not being set before probing the i2c bus for
devices (the probe would occur with the GPIOs being all high).
Make a call to em28xx_set_mode() so that the GPIOs are set properly before
probing the i2c bus for devices.
This problem was detected with the EVGA inDtube, where the tvp5150 is not
powered on unless GPIO1 is pulled low.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Name saturation control saturation, not color and make the default
less saturated (the old default was overdoing it).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise
the picture is upside down. It is better to instead invert the meaning
of the control in the set function, and have the default be no vflip,
as one would expect vflip enabled to be upside down.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: enable autogain control for the ov7620, and not only
make it enable autogain but also auto exposure (and do the
same for the ov7648).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer
overflows during my testing of a "Premier" 0c45:613e cam
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark the v4l1 uvcvideo quickcam messenger driver as deprecated, the one
cam it supports, is now also supported by the v4l2 gspca stv06xx driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: enable support for 0c45:613e camera, and slightly tweak
the ov7630 register init values for a much better picture.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control index defines for the gspca_sonixj driver were numbered
wrong, causing us to disable the wrong controls on various sensors
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark the v4l1 ov511 as deprecated as we now have ov511 support in
the gspca ov519 driver. Note we should really also keep track of this
in Documentation/feature-removal-schedule.txt, but that is not
part of the v4l-dvb tree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ov511: remove ov518 usb id's from the driver, as they have not been working
ever since the decompression code got removed from the kernel, and they
are no supported by the gspca_ov519 module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for st6422 bridge and sensor to the stv06xx gspca sub driver,
tested with:
Logitech QuickCam Messenger 046d:08f0 ST6422 integrated
Logitech QuickCam Mess. Plus 046d:08f6 ST6422 integrated
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: Cleanup some sensor special cases
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: add support for the ov511 bridge
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hmm, another one with an extra if (life sucks) the
default contrast really is no good for the ov6630, it
isn't even high enough in full daylight, this gives
the ov6630 a different initial value for a better out
of the box experience.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported on the ov51x-jpeg list, and as I can confirm with my own cam
the ov7670 in 320x240 has a number of broken columns of pixels
at the left of the picture. This was not present in the old
driver as it always used 640x480 and did software
downscaling (took me a while to figure that one out).
The fix adds a sensor specific if in so far sensor
neutral code :( But this is the only way to fix this,
this cannot be fixed by only changing sensor registers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My ov519 cam has it led inverted, the same has been
reported on the ov51x-jpeg list for another
creative cam. This patch fixes this without changing
the behaviour for other cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: Add 320x240 and 160x120 support for cif sensor cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fix for the UV swapping in qcif mode with the ov6630, which I did
to fix this issue on a ov518 cam with an ov66308AF, causes UV swapping in
qcif with another cam of mine with the ov518 and an ov66308AE, so this
patch changes the code to differentiate between the ov66308AF and other
ov6630 versions, and restricts the UV swap fix to the ov66308AF.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds autobrightness (so that it can
be turned off to make the already present brightness
control work) and light frequency filtering controls.
The lightfreq control needed 2 different entries
in the ctrls array, as the number of options differs
depending on the sensor. Always one of the 2 entires is
disabled ofcourse.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix Leadtek TV2000 XP Global entries and add missing PCI ID's.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing us for the proper settings.
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 5d23a1d2 ("net: replace dma_sync_single with
dma_sync_single_for_cpu") replaced uses of the deprectated function
dma_sync_single() with calls to dma_sync_single_for_cpu(). However,
to be correct, the code should do a sync for_cpu() before touching the
memory and for_device() after it's done.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dma_sync_single() is deprecated now, and the use in mthca is wrong:
there should be a dma_sync_single_for_cpu() before touching the memory
from the CPU, and a dma_sync_single_for_device() afterwards. Fix
this, prompted by a kick in the pants from a patch from FUJITA
Tomonori <fujita.tomonori@lab.ntt.co.jp>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Before issuing reset, libata configures xfermode to PIO0 which makes
some drivers turn on IORDY which may cause the controller to lock up
if the port is not occupied. IORDY isn't necessary at this point
anyway. Make ata_pio_need_iordy() return zero if it's being called
for reset.
This fixes bko#11703. Reported and tracked down by Daniel Gnoutcheff
and Constantine Gavrilov.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Daniel Gnoutcheff <gnoutchd@union.edu>
Cc: Constantine Gavrilov <constantine.gavrilov@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch provides PATA driver for CompactFlash interface in True IDE
mode on AT91SAM9260 SoC.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1. add defaults to description where possible
2. add value definition (off=0, on=1) where missing
v2: reformatted as per request by Jeff Garzik <jgarzik@pobox.com>
"Enable foo (0=off, 1=on [default])"
Signed-off-by: Evgeni Golov <sargentd@die-welt.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During cluster testing, one QP was not closed, as FIN is not handled
properly when its rexmit count expires or in some cases when RST is is
received after sending FIN. The reason is that the cm_id does not get
decremented under these conditions.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In nes_query_device(), max_qp_init_rd_atom is incorrectly set to
max_qp_wr. This was found when a test application had a dapl async
event error.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This prevents the memcpy() of a guid_entries element using a negative index.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement toleration of dynamic memory operations and 16 GB gigantic
pages, where "toleration" means that the driver can cope with dynamic
memory operations that happen before the driver is loaded. While the
ehca driver is loaded, dynamic memory operations are still prohibited
by returning NOTIFY_BAD from the memory notifier.
On module load the driver walks through available system memory,
checks for available memory ranges and then registers the kernel
internal memory region accordingly. The translation of address ranges
is implemented via a 3-level busmap.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits)
Blackfin: fix dma-mapping build errors
Blackfin: hook up new perf_counter_open syscall
Blackfin: drop BF535-specific text for exception 0x2A (unaligned instruction)
Blackfin: fix early crash when booting on wrong cpu
Blackfin: fix GPTMR0_CLOCKSOURCE dependency on BFIN_GPTIMERS
Blackfin: drop unused ISP1760 port1_disable from board resources
Blackfin: bf526-ezbrd: handle different SDRAM chips
Blackfin: fix typo in TRAS define in mem_init.h header
Blackfin: unify memory map headers
Blackfin: stick the CPU name into boot image name
Blackfin: update defconfigs
Blackfin: decouple unrelated cache settings to get exact behavior
Blackfin: update I-pipe patch level
Blackfin: remove obsolete mcount support from I-pipe code
Blackfin: allow CONFIG_TICKSOURCE_GPTMR0 with interrupt pipeline
Blackfin: convert interrupt pipeline to irqflags
Blackfin: allow people to select BF51x-0.1 silicon rev
Blackfin: bf526-ezbrd: set SPI flash resources to SST device
Blackfin: fix accidental reset in some boot modes
Blackfin: abstract irq14 lowering in do_irq
...
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix one last ia64 build problem in Pass Through Support
VT-d: support the device IOTLB
VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps
VT-d: add device IOTLB invalidation support
VT-d: parse ATSR in DMA Remapping Reporting Structure
PCI: handle Virtual Function ATS enabling
PCI: support the ATS capability
intel-iommu: dmar_set_interrupt return error value
intel-iommu: Tidy up iommu->gcmd handling
intel-iommu: Fix tiny theoretical race in write-buffer flush.
intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing.
intel-iommu: Clean up handling of "caching mode" vs. context flushing.
VT-d: fix invalid domain id for KVM context flush
Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support
Intel IOMMU Pass Through Support
Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
As noted in the previous patch, the NFSv4 client mount code currently
has several limitations. If the mount path contains symlinks, or
referrals, or even if it just contains a '..', then the client code in
nfs4_path_walk() will fail with an error.
This patch replaces the nfs4_path_walk()-based lookup with a helper
function that sets up a private namespace to represent the namespace on the
server, then uses the ordinary VFS and NFS path lookup code to walk down the
mount path in that namespace.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The purpose of this patch is to improve the remote mount path lookup
support for distributed filesystems such as the NFSv4 client.
When given a mount command of the form "mount server:/foo/bar /mnt", the
NFSv4 client is required to look up the filehandle for "server:/", and
then look up each component of the remote mount path "foo/bar" in order
to find the directory that is actually going to be mounted on /mnt.
Following that remote mount path may involve following symlinks,
crossing server-side mount points and even following referrals to
filesystem volumes on other servers.
Since the standard VFS path lookup code already supports walking paths
that contain all these features (using in-kernel automounts for
following referrals) we would like to be able to reuse that rather than
duplicate the full path traversal functionality in the NFSv4 client code.
This patch therefore defines a VFS helper function create_mnt_ns(), that
sets up a temporary filesystem namespace and attaches a root filesystem to
it. It exports the create_mnt_ns() and put_mnt_ns() function for use by
filesystem modules.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to allow modules to use it without having to export vfsmount_lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB uses get/put_online_cpus() which use a mutex which is itself only
initialized when cpu_hotplug_init() is called. Currently we hang suring
boot in SLAB due to doing that too late.
Reported by James Bottomley and Sachin Sant (and possibly others).
Debugged by Benjamin Herrenschmidt.
This just removes the dynamic initialization of the data structures, and
replaces it with a static one, avoiding this dependency entirely, and
removing one unnecessary special initcall.
Tested-by: Sachin Sant <sachinp@in.ibm.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
