po1030: There's a lot of redundant writes to the bridge and sensor.
Remove them.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split up the po1030 init into start and init. Add a start function.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, we're probing r/w registers at probe time.
This is potentially dangerous, probe some read only registers instead.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a po1030 auto white balancing control that's disabled by default
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously many of the v4l2 ctrls were set to their initial values at resume from ram/disk. This patch enforces the values stored in the ctrl cache.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch renames some register defines in the ov9650 sensor.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The po1030 register defines are unnecessarily complex, simplify them and also add some missing ones.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Regardless of the actual sensor orientation vflip = 0 is normal, and vflip = 1 is upside down. This patch makes that happen
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The power_down sensor struct member is almost has no purpose in the current driver abstraction. Remove it.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let the po1030 have a local v4l2 ctrl cache as this minimizes the load on reading the registers and improves performance.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5k83a sensor mounted on many acer laptops have a swiwel allowing it to be rotated. When the camera is in its rotated state, the image needs to be flipped. The only way to check for if the camera has been flipped is to continously poll a register in the m5602. This patch creates a kernel thread which does this. This patch renames some v4l2 ctrls and finally implements a cache in order to prevent unnecessary sensor reads.
Signed-off-by: Luk?? Karas <lukas.karas@centrum.cz>
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* serial:
imx: Check for NULL pointer deref before calling tty_encode_baud_rate
atmel_serial: fix hang in set_termios when crtscts is enabled
MAINTAINERS: update 8250 section, give Alan Cox a name
tty: fix sanity check
pty: Narrow the race on ldisc locking
tty: fix unused warning when TCGETX is not defined
ldisc: debug aids
ldisc: Make sure the ldisc isn't active when we close it
tty: Fix leaks introduced by the shift to separate ldisc objects
Fix conflicts in drivers/char/pty.c due to earlier version of the ldisc
race narrowing.
After enabling hardware flow control, any subsequent termios call may hang
waiting for the transmitter to drain. This appears to be caused by a
busy-loop in set_termios() waiting for the transmitter to become empty,
which may take a very long time (or hang indefinitely) if the device at
the other end is blocking us.
A quick look through the tty and serial_core code indicates that any
necessary flushing (which is optional) has already been done at this
point, so there's no need for the driver to flush the transmitter on its
own.
Fix it by removing the busy-loop altogether.
Tested-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The WARN_ON() that was added to tty_reopen can be triggered in the specific
case of a hangup occurring during a re-open of a tty which is not in the
middle of being otherwise closed.
In that case however the WARN() is bogus as we don't hold the neccessary
locks to make a correct decision.
The case we should be checking is "if the ldisc is not changing and reopen
is occuring". We could drop the WARN_ON but for the moment the debug is more
valuable even if it means taking a mutex as it will find any other cases.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pty code has always been buggy on its ldisc handling. The recent
changes made the window for the race much bigger. Pending fixing it
properly which is not at all trivial, at least make the race small again so
we don't disrupt other dev work.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If TCGETX is not defined, we end up with this warning:
drivers/char/tty_ioctl.c: In function ‘tty_mode_ioctl’:
drivers/char/tty_ioctl.c:950: warning: unused variable ‘ktermx’
Since the variable is only used in one case statement, push it down to
the local case scope.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (30 commits)
sparc64: Update defconfig.
sparc: Wire up sys_rt_tgsigqueueinfo().
openprom: Squelch useless GCC warning.
sparc: replace uses of CPU_MASK_ALL_PTR
sparc64: Add proper dynamic ftrace support.
sparc: Simplify code using is_power_of_2() routine.
sparc: move of_device common code to of_device_common
sparc: remove dma-mapping_{32|64}.h
sparc: use dma_map_page instead of dma_map_single
sparc: add sync_single_for_device and sync_sg_for_device to struct dma_ops
sparc: move the duplication in dma-mapping_{32|64}.h to dma-mapping.h
p9100: use standard fields for framebuffer physical address and length
leo: use standard fields for framebuffer physical address and length
cg6: use standard fields for framebuffer physical address and length
cg3: use standard fields for framebuffer physical address and length
cg14: use standard fields for framebuffer physical address and length
bw2: use standard fields for framebuffer physical address and length
sparc64: fix and optimize irq distribution
sparc64: Use new dynamic per-cpu allocator.
sparc64: Only allocate per-cpu areas for possible cpus.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits)
Blackfin: hook up new rt_tgsigqueueinfo syscall
Blackfin: improve CLKIN_HZ config default
Blackfin: initial support for ftrace grapher
Blackfin: initial support for ftrace
Blackfin: enable support for LOCKDEP
Blackfin: add preliminary support for STACKTRACE
Blackfin: move custom sections into sections.h
Blackfin: punt unused/wrong mutex-dec.h
Blackfin: add support for irqflags
Blackfin: add support for bzip2/lzma compressed kernel images
Blackfin: convert Kconfig style to def_bool
Blackfin: bf548-ezkit: update smsc911x resources
Blackfin: update aedos-ipipe code to upstream 1.10-00
Blackfin: bf537-stamp: update ADP5520 resources
Blackfin: bf518f-ezbrd: fix SPI CS for SPI flash
Blackfin: define SPI IRQ in board resources
Blackfin: do not configure the UART early if on wrong processor
Blackfin: fix deadlock in SMP IPI handler
Blackfin: fix flag storage for irq funcs
Blackfin: push down exception oops checking
...
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove some includings of blktrace_api.h
mg_disk: seperate mg_disk.h again
block: Introduce helper to reset queue limits to default values
cfq: remove extraneous '\n' in blktrace output
ubifs: register backing_dev_info
btrfs: properly register fs backing device
block: don't overwrite bdi->state after bdi_init() has been run
cfq: cleanup for last_end_request in cfq_data
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (38 commits)
ps3flash: Always read chunks of 256 KiB, and cache them
ps3flash: Cache the last accessed FLASH chunk
ps3: Replace direct file operations by callback
ps3: Switch ps3_os_area_[gs]et_rtc_diff to EXPORT_SYMBOL_GPL()
ps3: Correct debug message in dma_ioc0_map_pages()
drivers/ps3: Add missing annotations
ps3fb: Use ps3_system_bus_[gs]et_drvdata() instead of direct access
ps3flash: Use ps3_system_bus_[gs]et_drvdata() instead of direct access
ps3: shorten ps3_system_bus_[gs]et_driver_data to ps3_system_bus_[gs]et_drvdata
ps3: Use dev_[gs]et_drvdata() instead of direct access for system bus devices
block/ps3: remove driver_data direct access of struct device
ps3vram: Make ps3vram_priv.reports a void *
ps3vram: Remove no longer used ps3vram_priv.ddr_base
ps3vram: Replace mutex by spinlock + bio_list
block: Add bio_list_peek()
powerpc: Use generic atomic64_t implementation on 32-bit processors
lib: Provide generic atomic64_t implementation
powerpc: Add compiler memory barrier to mtmsr macro
powerpc/iseries: Mark signal_vsp_instruction() as maybe unused
powerpc/iseries: Fix unused function warning in iSeries DT code
...
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
therm_windtunnel: Convert to a new-style i2c driver
therm_adt746x: Convert to a new-style i2c driver
windfarm: Convert to new-style i2c drivers
therm_pm72: Convert to a new-style i2c driver
i2c-viapro: Add new PCI device ID for VX855
i2c/chips: Move max6875 to drivers/misc/eeprom
i2c: Do not give adapters a default parent
i2c: Do not probe for TV chips on Voodoo3 adapters
i2c: Retry automatically on arbitration loss
i2c: Remove void casts
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (27 commits)
ACPICA: Update version to 20090521.
ACPICA: Disable preservation of SCI enable bit (SCI_EN)
ACPICA: Region deletion: Ensure region object is removed from handler list
ACPICA: Eliminate extra call to NsGetParentNode
ACPICA: Simplify internal operation region interface
ACPICA: Update Load() to use operation region interfaces
ACPICA: New: AcpiInstallMethod - install a single control method
ACPICA: Invalidate DdbHandle after table unload
ACPICA: Fix reference count issues for DdbHandle object
ACPICA: Simplify and optimize NsGetNextNode function
ACPICA: Additional validation of _PRT packages (resource mgr)
ACPICA: Fix DebugObject output for DdbHandle objects
ACPICA: Fix allowable release order for ASL mutex objects
ACPICA: Mutex support: Fix release ordering issue and current sync level
ACPICA: Update version to 20090422.
ACPICA: Linux OSL: cleanup/update/merge
ACPICA: Fix implementation of AML BreakPoint operator (break to debugger)
ACPICA: Fix miscellaneous warnings under gcc 4+
ACPICA: Miscellaneous lint changes
ACPICA: Fix possible dereference of null pointer
...
The pty code has always been buggy on its ldisc handling. The recent
changes made the window for the race much bigger. Pending fixing it
properly which is not at all trivial, at least make the race small again so
we don't disrupt other dev work.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/sbus/char/openprom.c: In function ‘openprom_sunos_ioctl’:
drivers/sbus/char/openprom.c:306: warning: ‘opp’ may be used uninitialized in this function
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len
for physical address and length of framebuffer.
This also fixes output of the 'fbset -i' command - address and length
of the framebuffer are displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len
for physical address and length of framebuffer.
This also fixes output of the 'fbset -i' command - address and length
of the framebuffer are displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len
for physical address and length of framebuffer.
This also fixes output of the 'fbset -i' command - address and length
of the framebuffer are displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len
for physical address and length of framebuffer.
This also fixes output of the 'fbset -i' command - address and length
of the framebuffer is displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len
for physical address and length of framebuffer.
This also fixes output of the 'fbset -i' command - address and length
of the framebuffer is displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len
for physical address and length of framebuffer.
This also fixes output of the 'fbset -i' command - address and length
of the framebuffer is displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When porting blktrace to tracepoints, we changed to trace/block.h
for trace prober declarations.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Introduce the power management callbacks to the 3270 driver. On suspend
the current 3270 view is deactivated and for non-console 3270 device
the release callback is done. This disconnects the current tty /
fullscreen application from the 3270 device. On resume the current
view is reactivated, on the tty you get a fresh login.
If the system panics before the 3270 device has been resumed, the ccw
device for the 3270 console is reactivated with ccw_device_force_console.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Create dummy iucv-device to get control when the system is suspended
and resumed. Server the smsg iucv path on suspend, reestablish the
path on resume.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The patch adds supporting for suspending and resuming IUCV HVC terminal
devices from disk. The obligatory Linux device driver interfaces has
been added by registering a device driver on the IUCV bus.
For each IUCV HVC terminal device the driver creates a respective device
on the IUCV bus.
To support suspend and resume, the PM freeze callback severs any established
IUCV communication path and triggers a HVC tty hang-up when the system image
is restored.
IUCV communication path are no longer valid when the z/VM guest is halted.
The device driver initialization has been updated to register devices and
the a new routine has been extracted to facilitate the hang-up of IUCV HVC
terminal devices.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Patch establishes a dummy netiucv device to make sure iucv is notified
about suspend/resume even if netiucv is the only loaded iucv-exploting
module without any real net_device defined.
The PM freeze callback closes all open netiucv connections. Thus the
corresponding iucv path is removed.
The PM thaw/restore callback re-opens previously closed netiucv
connections.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The SCLP base driver defines a new notifier call back for all upper level SCLP
drivers, like the SCLP console, etc. This guarantees that in suspend first the
upper level drivers are suspended and afterwards the SCLP base driver. For
resume it is the other way round. The SCLP base driver itself registers a
new platform device at the platform bus and gets PM notifications via
the dev_pm_ops.
In suspend, the SCLP base driver switches off the receiver and sender mask
This is done in sclp_deactivate(). After suspend all new requests will be
rejected with -EIO and no more interrupts will be received, because the masks
are switched off. For resume the sender and receiver masks are reset in
the sclp_reactivate() function.
When the SCLP console is suspended, all new messages are cached in the
sclp console buffers. In resume, all the cached messages are written to the
console. In addition to that we have an early resume function that removes
the cached messages from the suspend image.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements suspend/hibernation for the vmwatchdog driver. The
pm_notifier_callchain is used to get control on PM events. Since watchdog
operation and suspend cannot work together in a reliable fashion, the open
flag is also used to prevent suspend and open from happening at the same
time.
The watchdog can also be active with no open file descriptor. This patch
adds another flag which is only changed in vmwdt_keep_alive and
vmwdt_disable.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the power management callbacks to the 3215 console. On suspend
the console buffer is flushed to the 3215 device to have an empty console
buffer. Printks done while the 3215 device is suspended are buffered in
the 64K buffer of the 3215 device. If the buffer is full new messages will
push out the oldest messages to make room for the most recent message.
On resume the buffered messages are printed. If the system panics before
the 3215 device is resumed ccw_device_force_console is used to get the
console working again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If something goes wrong in a suspend / resume cycle a ccw based console
if very likely in the suspended state and cannot print anything.
Introduce ccw_device_force_console to force the wake up of the console
device to be able to print the oops message. The console device drivers
should use this function only if the system paniced.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the power management callbacks to the dasd driver. On suspend
the dasd devices are stopped and removed from the focus of alias
management.
On resume they are reinitialized by rereading the device characteristics
and adding the device to the alias management.
In case the device has gone away during suspend it will caught in the
suspend state with stopped flag set to UNRESUMED. After it appears again
the restore function is called again.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
eec9462088 fold mg_disk.h into mg_disk.c,
but mg_disk platform driver needs private data for operation. This also
make mg_disk.c as machine independent. Seperate only needed structure and
defines to mg_disk.h
Signed-off-by: unsik Kim <donari75@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Export the alarm flags provided by the MAX6650/MAX6651 fan-speed regulator
and monitor chips via sysfs.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the hwmon part of the Fintek F71858FG superio IC to the
f71882fg driver. Many thanks to Jelle de Jong for lending me a motherboard
with this superio on it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on f71852fg support I noticed that the f8000 sysfs attr
table was missing entries for temp#_fault, which the f8000 does have and
which we were already reading.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We depend up on the pwm_enable register (0x96) not containing any reserved
settings in various places. We were already checking to make sure there
were no reserved settings in the register for the f71862fg, this patch adds
the same checking for the f8000, while at it it also moves the code to
a more apropriate place so we don't need to check if the fan/pwm part
of the IC is enabled twice.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently we are using separate per model sysfs attr for the 3th pwm, because
the 3th pwm of the f8000 only has automatic mode and not manual mode. Doing
things this way was getting in the way for adding f71858fg support, so this
patch makes the pwm attr identical for all models, and instead adds a check
to store_pwm_enable() disallowing setting the 3th pwm to manual mode
on a f8000 IC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MSI MS-7031 is based on an ATI IXP300 south bridge. On this south
bridge, accessible I/O ports must be enabled explicitly. Unfortunately
the BIOS forgets to enable access to the hardware monitoring chip I/O
ports, so hardware monitoring fails.
Add a quirk enabling access to the required ports (0x295-0x296). This
is exactly what MSI's own hardware monitoring application is doing, so
it has to be the right way.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the new incarnation of the Winbond/Nuvoton W83627DHG
chip known as W83627DHG-P. It is basically the same as the original
W83627DHG with an additional automatic can speed control mode (not
supported by the driver yet.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Madhu <madhu.chinakonda@gmail.com>
This adds support for TI's TMP411 sensor chip.
Preliminary support were done by Gabriel Konat, Sander Leget and
Wouter Willems. The chip is compatible with TI's TMP401 sensor
chip. It has additional support for historical minimun/maximum
measurements.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a new hwmon driver for TI's TMP401 temperature sensor IC. This driver
was written on behalf of an embedded systems vendor under the
Linux driver project.
It has been tested using a TI TMP401 sample attached to a i2c-tiny-usb adapter.
Which was provided by Till Harbaum, many thanks to him for this!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enable auto-probing for the HC10 blade and amend the supported system
list.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make sure __devexit and devexit_p() match in all hwmon drivers.
Suggested by a similar fix from Mike Frysinger.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
The legacy i2c binding model is going away soon, so convert the ppc
therm_windtunnel driver to the new model or it will break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
The legacy i2c binding model is going away soon, so convert the ppc
therm_adt746x driver to the new model or it will break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The legacy i2c binding model is going away soon, so convert the
macintosh windfarm drivers to the new model or they will break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The legacy i2c binding model is going away soon, so convert the
macintosh therm_pm72 driver to the new model or it will break.
This is really a quick and dirty conversion, that should do the trick
for now, but no doubt that something cleaner can be done if anyone is
interested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Paul Mackerras <paulus@samba.org>
The south bridge of the VIA VX855 chipset has a different PCI Device ID
so i2c-viapro.c needs to be updated with this.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This driver only reads the user EEPROM of that chip, so we can move it
to the eeprom-directory in order to further clean up (and later remove)
drivers/i2c/chips.
The Kconfig text was updated to match the current functionality,
dropping the meanwhile obsoleted parts.
Defconfigs have been adapted.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We don't need to give adapters a parent if they don't have one. The
driver core will put them in the virtual device directory and all will
be fine.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There's no point in giving the I2C bus of Voodoo3 adapters a class
value, there's no video chip driver checking for it anymore. If
support is ever needed, the video device should be instantiated
explicitly rather than probed.
To the best of my knowledge the only video chip that can be found on
these boards is a BT869 video encoder, for which no support exists
currently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Some small changes in i2c core to retry i2c xfers until either the
maximum number of retries or the timeout is hit.
Signed-off-by: Clifford Wolf <clifford@clifford.at>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On Thu, May 28, 2009 at 10:59 AM, Mark Brown <broonie@opensource.wolfsonmicro.com> wrote:
> On Thu, May 28, 2009 at 07:15:16AM +0200, Philipp Zabel wrote:
>> The V3 regulator can be configured with an external resistor
>> connected to the feedback pin (R24 in the data sheet) to
>> increase the voltage range.
>>
>> For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
>> V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
>>
>> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
>
> Looks good.
>
> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Thanks, but it turns out I hit a 32 bit integer overflow in
the gain calculation. I'd like to mend that with the following
patch. Now max_uV could be increased up to 4.294 V, enough to
charge LiPo cells.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The V3 regulator can be configured with an external resistor
connected to the feedback pin (R24 in the data sheet) to
increase the voltage range.
For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
lp3971_i2c_remove' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.devexit.text' of drivers/built-in.o
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
