This replaces the single CPU_FTR_HVMODE_206 bit with two bits, one to
indicate that we have a usable hypervisor mode, and another to indicate
that the processor conforms to PowerISA version 2.06. We also add
another bit to indicate that the processor conforms to ISA version 2.01
and set that for PPC970 and derivatives.
Some PPC970 chips (specifically those in Apple machines) have a
hypervisor mode in that MSR[HV] is always 1, but the hypervisor mode
is not useful in the sense that there is no way to run any code in
supervisor mode (HV=0 PR=0). On these processors, the LPES0 and LPES1
bits in HID4 are always 0, and we use that as a way of detecting that
hypervisor mode is not useful.
Where we have a feature section in assembly code around code that
only applies on POWER7 in hypervisor mode, we use a construct like
END_FTR_SECTION_IFSET(CPU_FTR_HVMODE | CPU_FTR_ARCH_206)
The definition of END_FTR_SECTION_IFSET is such that the code will
be enabled (not overwritten with nops) only if all bits in the
provided mask are set.
Note that the CPU feature check in __tlbie() only needs to check the
ARCH_206 bit, not the HVMODE bit, because __tlbie() can only get called
if we are running bare-metal, i.e. in hypervisor mode.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds infrastructure which will be needed to allow book3s_hv KVM to
run on older POWER processors, including PPC970, which don't support
the Virtual Real Mode Area (VRMA) facility, but only the Real Mode
Offset (RMO) facility. These processors require a physically
contiguous, aligned area of memory for each guest. When the guest does
an access in real mode (MMU off), the address is compared against a
limit value, and if it is lower, the address is ORed with an offset
value (from the Real Mode Offset Register (RMOR)) and the result becomes
the real address for the access. The size of the RMA has to be one of
a set of supported values, which usually includes 64MB, 128MB, 256MB
and some larger powers of 2.
Since we are unlikely to be able to allocate 64MB or more of physically
contiguous memory after the kernel has been running for a while, we
allocate a pool of RMAs at boot time using the bootmem allocator. The
size and number of the RMAs can be set using the kvm_rma_size=xx and
kvm_rma_count=xx kernel command line options.
KVM exports a new capability, KVM_CAP_PPC_RMA, to signal the availability
of the pool of preallocated RMAs. The capability value is 1 if the
processor can use an RMA but doesn't require one (because it supports
the VRMA facility), or 2 if the processor requires an RMA for each guest.
This adds a new ioctl, KVM_ALLOCATE_RMA, which allocates an RMA from the
pool and returns a file descriptor which can be used to map the RMA. It
also returns the size of the RMA in the argument structure.
Having an RMA means we will get multiple KMV_SET_USER_MEMORY_REGION
ioctl calls from userspace. To cope with this, we now preallocate the
kvm->arch.ram_pginfo array when the VM is created with a size sufficient
for up to 64GB of guest memory. Subsequently we will get rid of this
array and use memory associated with each memslot instead.
This moves most of the code that translates the user addresses into
host pfns (page frame numbers) out of kvmppc_prepare_vrma up one level
to kvmppc_core_prepare_memory_region. Also, instead of having to look
up the VMA for each page in order to check the page size, we now check
that the pages we get are compound pages of 16MB. However, if we are
adding memory that is mapped to an RMA, we don't bother with calling
get_user_pages_fast and instead just offset from the base pfn for the
RMA.
Typically the RMA gets added after vcpus are created, which makes it
inconvenient to have the LPCR (logical partition control register) value
in the vcpu->arch struct, since the LPCR controls whether the processor
uses RMA or VRMA for the guest. This moves the LPCR value into the
kvm->arch struct and arranges for the MER (mediated external request)
bit, which is the only bit that varies between vcpus, to be set in
assembly code when going into the guest if there is a pending external
interrupt request.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This lifts the restriction that book3s_hv guests can only run one
hardware thread per core, and allows them to use up to 4 threads
per core on POWER7. The host still has to run single-threaded.
This capability is advertised to qemu through a new KVM_CAP_PPC_SMT
capability. The return value of the ioctl querying this capability
is the number of vcpus per virtual CPU core (vcore), currently 4.
To use this, the host kernel should be booted with all threads
active, and then all the secondary threads should be offlined.
This will put the secondary threads into nap mode. KVM will then
wake them from nap mode and use them for running guest code (while
they are still offline). To wake the secondary threads, we send
them an IPI using a new xics_wake_cpu() function, implemented in
arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage
we assume that the platform has a XICS interrupt controller and
we are using icp-native.c to drive it. Since the woken thread will
need to acknowledge and clear the IPI, we also export the base
physical address of the XICS registers using kvmppc_set_xics_phys()
for use in the low-level KVM book3s code.
When a vcpu is created, it is assigned to a virtual CPU core.
The vcore number is obtained by dividing the vcpu number by the
number of threads per core in the host. This number is exported
to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes
to run the guest in single-threaded mode, it should make all vcpu
numbers be multiples of the number of threads per core.
We distinguish three states of a vcpu: runnable (i.e., ready to execute
the guest), blocked (that is, idle), and busy in host. We currently
implement a policy that the vcore can run only when all its threads
are runnable or blocked. This way, if a vcpu needs to execute elsewhere
in the kernel or in qemu, it can do so without being starved of CPU
by the other vcpus.
When a vcore starts to run, it executes in the context of one of the
vcpu threads. The other vcpu threads all go to sleep and stay asleep
until something happens requiring the vcpu thread to return to qemu,
or to wake up to run the vcore (this can happen when another vcpu
thread goes from busy in host state to blocked).
It can happen that a vcpu goes from blocked to runnable state (e.g.
because of an interrupt), and the vcore it belongs to is already
running. In that case it can start to run immediately as long as
the none of the vcpus in the vcore have started to exit the guest.
We send the next free thread in the vcore an IPI to get it to start
to execute the guest. It synchronizes with the other threads via
the vcore->entry_exit_count field to make sure that it doesn't go
into the guest if the other vcpus are exiting by the time that it
is ready to actually enter the guest.
Note that there is no fixed relationship between the hardware thread
number and the vcpu number. Hardware threads are assigned to vcpus
as they become runnable, so we will always use the lower-numbered
hardware threads in preference to higher-numbered threads if not all
the vcpus in the vcore are runnable, regardless of which vcpus are
runnable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This improves I/O performance for guests using the PAPR
paravirtualization interface by making the H_PUT_TCE hcall faster, by
implementing it in real mode. H_PUT_TCE is used for updating virtual
IOMMU tables, and is used both for virtual I/O and for real I/O in the
PAPR interface.
Since this moves the IOMMU tables into the kernel, we define a new
KVM_CREATE_SPAPR_TCE ioctl to allow qemu to create the tables. The
ioctl returns a file descriptor which can be used to mmap the newly
created table. The qemu driver models use them in the same way as
userspace managed tables, but they can be updated directly by the
guest with a real-mode H_PUT_TCE implementation, reducing the number
of host/guest context switches during guest IO.
There are certain circumstances where it is useful for userland qemu
to write to the TCE table even if the kernel H_PUT_TCE path is used
most of the time. Specifically, allowing this will avoid awkwardness
when we need to reset the table. More importantly, we will in the
future need to write the table in order to restore its state after a
checkpoint resume or migration.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds the infrastructure for handling PAPR hcalls in the kernel,
either early in the guest exit path while we are still in real mode,
or later once the MMU has been turned back on and we are in the full
kernel context. The advantage of handling hcalls in real mode if
possible is that we avoid two partition switches -- and this will
become more important when we support SMT4 guests, since a partition
switch means we have to pull all of the threads in the core out of
the guest. The disadvantage is that we can only access the kernel
linear mapping, not anything vmalloced or ioremapped, since the MMU
is off.
This also adds code to handle the following hcalls in real mode:
H_ENTER Add an HPTE to the hashed page table
H_REMOVE Remove an HPTE from the hashed page table
H_READ Read HPTEs from the hashed page table
H_PROTECT Change the protection bits in an HPTE
H_BULK_REMOVE Remove up to 4 HPTEs from the hashed page table
H_SET_DABR Set the data address breakpoint register
Plus code to handle the following hcalls in the kernel:
H_CEDE Idle the vcpu until an interrupt or H_PROD hcall arrives
H_PROD Wake up a ceded vcpu
H_REGISTER_VPA Register a virtual processor area (VPA)
The code that runs in real mode has to be in the base kernel, not in
the module, if KVM is compiled as a module. The real-mode code can
only access the kernel linear mapping, not vmalloc or ioremap space.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for KVM running on 64-bit Book 3S processors,
specifically POWER7, in hypervisor mode. Using hypervisor mode means
that the guest can use the processor's supervisor mode. That means
that the guest can execute privileged instructions and access privileged
registers itself without trapping to the host. This gives excellent
performance, but does mean that KVM cannot emulate a processor
architecture other than the one that the hardware implements.
This code assumes that the guest is running paravirtualized using the
PAPR (Power Architecture Platform Requirements) interface, which is the
interface that IBM's PowerVM hypervisor uses. That means that existing
Linux distributions that run on IBM pSeries machines will also run
under KVM without modification. In order to communicate the PAPR
hypercalls to qemu, this adds a new KVM_EXIT_PAPR_HCALL exit code
to include/linux/kvm.h.
Currently the choice between book3s_hv support and book3s_pr support
(i.e. the existing code, which runs the guest in user mode) has to be
made at kernel configuration time, so a given kernel binary can only
do one or the other.
This new book3s_hv code doesn't support MMIO emulation at present.
Since we are running paravirtualized guests, this isn't a serious
restriction.
With the guest running in supervisor mode, most exceptions go straight
to the guest. We will never get data or instruction storage or segment
interrupts, alignment interrupts, decrementer interrupts, program
interrupts, single-step interrupts, etc., coming to the hypervisor from
the guest. Therefore this introduces a new KVMTEST_NONHV macro for the
exception entry path so that we don't have to do the KVM test on entry
to those exception handlers.
We do however get hypervisor decrementer, hypervisor data storage,
hypervisor instruction storage, and hypervisor emulation assist
interrupts, so we have to handle those.
In hypervisor mode, real-mode accesses can access all of RAM, not just
a limited amount. Therefore we put all the guest state in the vcpu.arch
and use the shadow_vcpu in the PACA only for temporary scratch space.
We allocate the vcpu with kzalloc rather than vzalloc, and we don't use
anything in the kvmppc_vcpu_book3s struct, so we don't allocate it.
We don't have a shared page with the guest, but we still need a
kvm_vcpu_arch_shared struct to store the values of various registers,
so we include one in the vcpu_arch struct.
The POWER7 processor has a restriction that all threads in a core have
to be in the same partition. MMU-on kernel code counts as a partition
(partition 0), so we have to do a partition switch on every entry to and
exit from the guest. At present we require the host and guest to run
in single-thread mode because of this hardware restriction.
This code allocates a hashed page table for the guest and initializes
it with HPTEs for the guest's Virtual Real Memory Area (VRMA). We
require that the guest memory is allocated using 16MB huge pages, in
order to simplify the low-level memory management. This also means that
we can get away without tracking paging activity in the host for now,
since huge pages can't be paged or swapped.
This also adds a few new exports needed by the book3s_hv code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There are several fields in struct kvmppc_book3s_shadow_vcpu that
temporarily store bits of host state while a guest is running,
rather than anything relating to the particular guest or vcpu.
This splits them out into a new kvmppc_host_state structure and
modifies the definitions in asm-offsets.c to suit.
On 32-bit, we have a kvmppc_host_state structure inside the
kvmppc_book3s_shadow_vcpu since the assembly code needs to be able
to get to them both with one pointer. On 64-bit they are separate
fields in the PACA. This means that on 64-bit we don't need to
copy the kvmppc_host_state in and out on vcpu load/unload, and
in future will mean that the book3s_hv code doesn't need a
shadow_vcpu struct in the PACA at all. That does mean that we
have to be careful not to rely on any values persisting in the
hstate field of the paca across any point where we could block
or get preempted.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In hypervisor mode, the LPCR controls several aspects of guest
partitions, including virtual partition memory mode, and also controls
whether the hypervisor decrementer interrupts are enabled. This sets
up LPCR at boot time so that guest partitions will use a virtual real
memory area (VRMA) composed of 16MB large pages, and hypervisor
decrementer interrupts are disabled.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Instead of doing the kvm_guest_enter/exit() and local_irq_dis/enable()
calls in powerpc.c, this moves them down into the subarch-specific
book3s_pr.c and booke.c. This eliminates an extra local_irq_enable()
call in book3s_pr.c, and will be needed for when we do SMT4 guest
support in the book3s hypervisor mode code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This arranges for the top-level arch/powerpc/kvm/powerpc.c file to
pass down some of the calls it gets to the lower-level subarchitecture
specific code. The lower-level implementations (in booke.c and book3s.c)
are no-ops. The coming book3s_hv.c will need this.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Doing so means that we don't have to save the flags anywhere and gets
rid of the last reference to to_book3s(vcpu) in arch/powerpc/kvm/book3s.c.
Doing so is OK because a program interrupt won't be generated at the
same time as any other synchronous interrupt. If a program interrupt
and an asynchronous interrupt (external or decrementer) are generated
at the same time, the program interrupt will be delivered, which is
correct because it has a higher priority, and then the asynchronous
interrupt will be masked.
We don't ever generate system reset or machine check interrupts to the
guest, but if we did, then we would need to make sure they got delivered
rather than the program interrupt. The current code would be wrong in
this situation anyway since it would deliver the program interrupt as
well as the reset/machine check interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Instead of branching out-of-line with the DO_KVM macro to check if we
are in a KVM guest at the time of an interrupt, this moves the KVM
check inline in the first-level interrupt handlers. This speeds up
the non-KVM case and makes sure that none of the interrupt handlers
are missing the check.
Because the first-level interrupt handlers are now larger, some things
had to be move out of line in exceptions-64s.S.
This all necessitated some minor changes to the interrupt entry code
in KVM. This also streamlines the book3s_32 KVM test.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In preparation for adding code to enable KVM to use hypervisor mode
on 64-bit Book 3S processors, this splits book3s.c into two files,
book3s.c and book3s_pr.c, where book3s_pr.c contains the code that is
specific to running the guest in problem state (user mode) and book3s.c
contains code which should apply to all Book 3S processors.
In doing this, we abstract some details, namely the interrupt offset,
updating the interrupt pending flag, and detecting if the guest is
in a critical section. These are all things that will be different
when we use hypervisor mode.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This moves the slb field, which represents the state of the emulated
SLB, from the kvmppc_vcpu_book3s struct to the kvm_vcpu_arch, and the
hpte_hash_[v]pte[_long] fields from kvm_vcpu_arch to kvmppc_vcpu_book3s.
This is in accord with the principle that the kvm_vcpu_arch struct
represents the state of the emulated CPU, and the kvmppc_vcpu_book3s
struct holds the auxiliary data structures used in the emulation.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 69acc0d3ba ("KVM: PPC: Resolve real-mode handlers through
function exports") resulted in vcpu->arch.trampoline_lowmem and
vcpu->arch.trampoline_enter ending up with kernel virtual addresses
rather than physical addresses. This is OK on 64-bit Book3S machines,
which ignore the top 4 bits of the effective address in real mode,
but on 32-bit Book3S machines, accessing these addresses in real mode
causes machine check interrupts, as the hardware uses the whole
effective address as the physical address in real mode.
This fixes the problem by using __pa() to convert these addresses
to physical addresses.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Only look in the 4 entries that could possibly contain the
entry we're looking for.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Dynamically assign host PIDs to guest PIDs, splitting each guest PID into
multiple host (shadow) PIDs based on kernel/user and MSR[IS/DS]. Use
both PID0 and PID1 so that the shadow PIDs for the right mode can be
selected, that correspond both to guest TID = zero and guest TID = guest
PID.
This allows us to significantly reduce the frequency of needing to
invalidate the entire TLB. When the guest mode or PID changes, we just
update the host PID0/PID1. And since the allocation of shadow PIDs is
global, multiple guests can share the TLB without conflict.
Note that KVM does not yet support the guest setting PID1 or PID2 to
a value other than zero. This will need to be fixed for nested KVM
to work. Until then, we enforce the requirement for guest PID1/PID2
to stay zero by failing the emulation if the guest tries to set them
to something else.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Instead of a fully separate set of TLB entries, keep just the
pfn and dirty status.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is a shared page used for paravirtualization. It is always present
in the guest kernel's effective address space at the address indicated
by the hypercall that enables it.
The physical address specified by the hypercall is not used, as
e500 does not have real mode.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows large pages to be used on guest mappings backed by things like
/dev/mem, resulting in a significant speedup when guest memory
is mapped this way (it's useful for directly-assigned MMIO, too).
This is not a substitute for hugetlbfs integration, but is useful for
configurations where devices are directly assigned on chips without an
IOMMU -- in these cases, we need guest physical and true physical to
match, and be contiguous, so static reservation and mapping via /dev/mem
is the most straightforward way to set things up.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is in line with what other architectures do, and will allow us to
map things other than ordinary, unreserved kernel pages -- such as
dedicated devices, or large contiguous reserved regions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This avoids races. It also means that we use the shadow TLB way,
rather than the hardware hint -- if this is a problem, we could do
a tlbsx before inserting a TLB0 entry.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since TLB1 loading doesn't check the shadow TLB before allocating another
entry, you can get duplicates.
Once shadow PIDs are enabled in a later patch, we won't need to
invalidate the TLB on every switch, so this optimization won't be
needed anyway.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is done lazily. The SPE save will be done only if the guest has
used SPE since the last preemption or heavyweight exit. Restore will be
done only on demand, when enabling MSR_SPE in the shadow MSR, in response
to an SPE fault or mtmsr emulation.
For SPEFSCR, Linux already switches it on context switch (non-lazily), so
the only remaining bit is to save it between qemu and the guest.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Keep the guest MSR and the guest-mode true MSR separate, rather than
modifying the guest MSR on each guest entry to produce a true MSR.
Any bits which should be modified based on guest MSR must be explicitly
propagated from vcpu->arch.shared->msr to vcpu->arch.shadow_msr in
kvmppc_set_msr().
While we're modifying the guest entry code, reorder a few instructions
to bury some load latencies.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Previously, these macros hardcoded THREAD_EVR0 as the base of the save
area, relative to the base register passed. This base offset is now
passed as a separate macro parameter, allowing reuse with other SPE
save areas, such as used by KVM.
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
giveup_spe() saves the SPE state which is protected by MSR[SPE].
However, modifying SPEFSCR does not trap when MSR[SPE]=0.
And since SPEFSCR is already saved/restored in _switch(),
not all the callers want to save SPEFSCR again.
Thus, saving SPEFSCR should not belong to giveup_spe().
This patch moves SPEFSCR saving to flush_spe_to_thread(),
and cleans up the caller that needs to save SPEFSCR accordingly.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Up until now, Book3S KVM had variables stored in the kernel that a kernel module
or the kvm code in the kernel could read from to figure out where some real mode
helper functions are located.
This is all unnecessary. The high bits of the EA get ignore in real mode, so we
can just use the pointer as is. Also, it's a lot easier on relocations when we
use the normal way of resolving the address to a function, instead of jumping
through hoops.
This patch fixes compilation with CONFIG_RELOCATABLE=y.
Signed-off-by: Alexander Graf <agraf@suse.de>
When http://www.spinics.net/lists/kvm-ppc/msg02664.html
was applied to produce commit b51e7aa7ed6d8d134d02df78300ab0f91cfff4d2,
the removal of the conversion in add_exit_timing was left out.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Just compiling pseries in the kernel causes it to override
memory_block_size_bytes() regardless of what is the runtime
platform.
This cleans up the implementation of that function, fixing
a bug or two while at it, so that it's harmless (and potentially
useful) for other platforms. Without this, bugs in that code
would trigger a WARN_ON() in drivers/base/memory.c when
booting some different platforms.
If/when we have another platform supporting memory hotplug we
might want to either move that out to a generic place or
make it a ppc_md. callback.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only reason to require a dma_ops struct is to see if it has
implemented set_dma_mask. If not we can fall back to setting the mask
directly.
This resolves an issue with how to sequence the setting of a DMA mask
for platform devices. Before we had an issue in that we have no way of
setting the DMA mask before the various low level bus notifiers get
called that might check it (swiotlb).
So now we can do:
pdev = platform_device_alloc("foobar", 0);
dma_set_mask(&pdev->dev, DMA_BIT_MASK(37));
platform_device_add(pdev);
And expect the right thing to happen with the bus notifiers get called
via platform_device_add.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We have a long standing issues with platform devices not have a valid
dma_mask pointer. This hasn't been an issue to date as no platform
device has tried to set its dma_mask value to a non-default value.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is used to round-robin TLBCAM entries.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On P1022DS both ethernet controllers are connected to RGMII PHYs
accessible via MDIO bus. Remove fixed-link property from ethernet
nodes as they only required when fixed link PHYs without MDIO bus
are used.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Under the FSL Hypervisor we triggered a BUG_ON in mpc85xx_smp_init that
expected smp_ops.message_pass to be explicity set. However recent
changes allows smp_ops.message_pass to be NULL and handled by default
code. Thus the BUG_ON isn't relevant anymore.
Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_PPC_EPAPR_HV_BYTECHAN adds support for the Freescale hypervisor
byte channel tty driver.
CONFIG_VIRT_DRIVERS and CONFIG_FSL_HV_MANAGER add support for the Freescale
hypervisor management driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
GPIO drivers are getting consolidated into drivers/gpio. While at it,
change the driver name to mpc5200-gpio* to avoid collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch a8b0ca17b8 ("perf: Remove the nmi parameter from the swevent
and overflow interface") missed a spot in the ppc hw_breakpoint code,
fix this up so things compile again.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-09pfip95g88s70iwkxu6nnbt@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The perf_event overflow handler does not receive any caller-derived
argument, so many callers need to resort to looking up the perf_event
in their local data structure. This is ugly and doesn't scale if a
single callback services many perf_events.
Fix by adding a context parameter to perf_event_create_kernel_counter()
(and derived hardware breakpoints APIs) and storing it in the perf_event.
The field can be accessed from the callback as event->overflow_handler_context.
All callers are updated.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1309362157-6596-2-git-send-email-avi@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a NODE level to the generic cache events which is used to measure
local vs remote memory accesses. Like all other cache events, an
ACCESS is HIT+MISS, if there is no way to distinguish between reads
and writes do reads only etc..
The below needs filling out for !x86 (which I filled out with
unsupported events).
I'm fairly sure ARM can leave it like that since it doesn't strike me as
an architecture that even has NUMA support. SH might have something since
it does appear to have some NUMA bits.
Sparc64, PowerPC and MIPS certainly want a good look there since they
clearly are NUMA capable.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Miller <davem@davemloft.net>
Cc: Anton Blanchard <anton@samba.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1303508226.4865.8.camel@laptop
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The nmi parameter indicated if we could do wakeups from the current
context, if not, we would set some state and self-IPI and let the
resulting interrupt do the wakeup.
For the various event classes:
- hardware: nmi=0; PMI is in fact an NMI or we run irq_work_run from
the PMI-tail (ARM etc.)
- tracepoint: nmi=0; since tracepoint could be from NMI context.
- software: nmi=[0,1]; some, like the schedule thing cannot
perform wakeups, and hence need 0.
As one can see, there is very little nmi=1 usage, and the down-side of
not using it is that on some platforms some software events can have a
jiffy delay in wakeup (when arch_irq_work_raise isn't implemented).
The up-side however is that we can remove the nmi parameter and save a
bunch of conditionals in fast paths.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/n/tip-agjev8eu666tvknpb3iaj0fg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit e360adbe29 ("irq_work: Add generic hardirq context
callbacks") fouled up the ppc bit, not properly naming the
arch specific function that raises the 'self-IPI'.
Cc: Huang Ying <ying.huang@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: stable@kernel.org # 37+
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-eg0aqien8p1aqvzu9dft6dtv@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
gcc 4.7 will be more strict about parsing the -mtraceback option:
gcc: error: unrecognized argument in option '-mtraceback=none'
gcc: note: valid arguments to '-mtraceback=' are: full no part
gcc used to do a 2 char compare so both "no" and "none" would
match. Switch to using -mtraceback=no should work everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the new "jump label" feature.
Unlike x86 and sparc we just merrily patch the code with no locks etc,
as far as I know this is safe, but I'm not really sure what the x86/sparc
code is protecting against so maybe it's not.
I also don't see any reason for us to implement the poke_early() routine,
even though sparc does.
[BenH: Updated the patch to upstream generic changes]
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A mix of think & mismerge on my side caused a problem where both the
new hvsi_lib and the old hvsi driver gets compiled and try to define
symbols with the same name.
This fixes it by renaming the hvsi_lib exported symbols.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
a9c0f41b3a breaks the build
on some platforms. The extern declaration must be shielded
against assembly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a printk companion to replace the udbg progress function
when initmem is freed.
Suggested-by: Milton Miller <miltonm@bga.com>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Carroll <dcarroll@astekcorp.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The free_initmem function is basically duplicated in mm/init_32,
and init_64, and is moved to the common 32/64-bit mm/mem.c.
All other sections except init were removed in v2.6.15 by
6c45ab992e (powerpc: Remove section
free() and linker script bits), and therefore the bulk of the executed
code is identical.
This patch also removes updating ppc_md.progress to NULL in the powermac
late_initcall.
Suggested-by: Milton Miller <miltonm@bga.com>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Carroll <dcarroll@astekcorp.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
arch/powerpc: use printk_ratelimited instead of printk_ratelimit
powerpc/rtas-rtc: remove sideeffects of printk_ratelimit
powerpc/pseries: remove duplicate SCSI_BNX2_ISCSI in pseries_defconfig
powerpc/e500: fix breakage with fsl_rio_mcheck_exception
powerpc/p1022ds: fix audio-related properties in the device tree
powerpc/85xx: fix NAND_CMD_READID read bytes number
On pseries machines, consoles are provided by the hypervisor using
a low level get_chars/put_chars type interface. However, this is
really just a transport to the service processor which implements
them either as "raw" console (networked consoles, HMC, ...) or as
"hvsi" serial ports.
The later is a simple packet protocol on top of the raw character
interface that is supposed to convey additional "serial port" style
semantics. In practice however, all it does is provide a way to
read the CD line and set/clear our DTR line, that's it.
We currently implement the "raw" protocol as an hvc console backend
(/dev/hvcN) and the "hvsi" protocol using a separate tty driver
(/dev/hvsi0).
However this is quite impractical. The arbitrary difference between
the two type of devices has been a major source of user (and distro)
confusion. Additionally, there's an additional mini -hvsi implementation
in the pseries platform code for our low level debug console and early
boot kernel messages, which means code duplication, though that low
level variant is impractical as it's incapable of doing the initial
protocol negociation to establish the link to the FSP.
This essentially replaces the dedicated hvsi driver and the platform
udbg code completely by extending the existing hvc_vio backend used
in "raw" mode so that:
- It now supports HVSI as well
- We add support for hvc backend providing tiocm{get,set}
- It also provides a udbg interface for early debug and boot console
This is overall less code, though this will only be obvious once we
remove the old "hvsi" driver, which is still available for now. When
the old driver is enabled, the new code still kicks in for the low
level udbg console, replacing the old mini implementation in the platform
code, it just doesn't provide the higher level "hvc" interface.
In addition to producing generally simler code, this has several benefits
over our current situation:
- The user/distro only has to deal with /dev/hvcN for the hypervisor
console, avoiding all sort of confusion that has plagued us in the past
- The tty, kernel and low level debug console all use the same code
base which supports the full protocol establishment process, thus the
console is now available much earlier than it used to be with the
old HVSI driver. The kernel console works much earlier and udbg is
available much earlier too. Hackers can enable a hard coded very-early
debug console as well that works with HVSI (previously that was only
supported for the "raw" mode).
I've tried to keep the same semantics as hvsi relative to how I react
to things like CD changes, with some subtle differences though:
- I clear DTR on close if HUPCL is set
- Current hvsi triggers a hangup if it detects a up->down transition
on CD (you can still open a console with CD down). My new implementation
triggers a hangup if the link to the FSP is severed, and severs it upon
detecting a up->down transition on CD.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When CONFIG_PPC_EARLY_DEBUG is set, call register_early_udbg_console()
early from generic code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Embed the struct hvsi_header in the various packet definitions
rather than open coding it multiple times. Will help provide
stronger type checking.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves various HVSI protocol definitions from the hvsi.c
driver to a header file that can be used later on by a udbg
implementation
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently Maple setup code creates cpc925_edac device only on
Motorola ATCA-6101 blade. Make setup code check bridge revision
and enable EDAC on all U3H bridges.
Verified on Momentum MapleD (ppc970fx kit) board.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reconfiguration notifier call for device node may fail by several reasons,
but it always assumes kmalloc failures.
This enables reconfiguration notifier call chain to get the actual error
code rather than -ENOMEM by converting all reconfiguration notifier calls
to return encapsulate error code with notifier_from_errno().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This introduces pSeries_reconfig_notify() as a just wrapper of
blocking_notifier_call_chain() for pSeries_reconfig_chain.
This is a preparation to improvement of error code on reconfiguration
notifier failure.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable functions used to access SCOM if PPC_MAPLE is defined: they are
used by cpufreq driver to control hardware.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This has been broken for a while but hasn't been an issue until
now because nobody was reserving regions at high addresses.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On MMUs such as FSL where we can guarantee the entire linear mapping is
bolted, we don't need to worry about linear TLB misses. If on top of
that we do a full table walk, we get rid of all recursive TLB faults, and
can dispense with some state saving. This gains a few percent on
TLB-miss-heavy workloads, and around 50% on a benchmark that had a high
rate of virtual page table faults under the normal handler.
While touching the EX_TLB layout, remove EX_TLB_MMUCR0, EX_TLB_SRR0, and
EX_TLB_SRR1 as they're not used.
[BenH: Fixed build with 64K pages (wsp config)]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't use printk_ratelimit() as an additional condition for returning
on an error. Because when the ratelimit is reached, printk_ratelimit
will return 0 and e.g. in rtas_get_boot_time won't check for an error
condition.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove duplicate assignment of SCSI_BNX2_ISCSI in pseries_defconfig
introduced by:
37e0c21e powerpc/pseries: Enable iSCSI support for a number of cards
causes warning:
arch/powerpc/configs/pseries_defconfig:151:warning: override: reassigning to symbol SCSI_BNX2_ISCSI
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This will allow the new HW RNG driver to bind on these boards
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Sequoia board has a Security function IP block on it that contains a TRNG.
Add the crypto and rng portions of that IP block to the DTS.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
commit 21a3c96 uses node_start/end_pfn(nid) for detection start/end
of nodes. But, it's not defined in linux/mmzone.h but defined in
/arch/???/include/mmzone.h which is included only under
CONFIG_NEED_MULTIPLE_NODES=y.
Then, we see
mm/page_cgroup.c: In function 'page_cgroup_init':
mm/page_cgroup.c:308: error: implicit declaration of function 'node_start_pfn'
mm/page_cgroup.c:309: error: implicit declaration of function 'node_end_pfn'
So, fixiing page_cgroup.c is an idea...
But node_start_pfn()/node_end_pfn() is a very generic macro and
should be implemented in the same manner for all archs.
(m32r has different implementation...)
This patch removes definitions of node_start/end_pfn() in each archs
and defines a unified one in linux/mmzone.h. It's not under
CONFIG_NEED_MULTIPLE_NODES, now.
A result of macro expansion is here (mm/page_cgroup.c)
for !NUMA
start_pfn = ((&contig_page_data)->node_start_pfn);
end_pfn = ({ pg_data_t *__pgdat = (&contig_page_data); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});
for NUMA (x86-64)
start_pfn = ((node_data[nid])->node_start_pfn);
end_pfn = ({ pg_data_t *__pgdat = (node_data[nid]); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});
Changelog:
- fixed to avoid using "nid" twice in node_end_pfn() macro.
Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Freescale hypervisor does not allow guests to write to the timebase
registers (virtualizing the timebase register was deemed too complicated),
so don't try to synchronize the timebase registers when we're running
under the hypervisor.
This typically happens when kexec support is enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable framebuffer console support by default in the defconfig on the
Freescale MPC8610 HPCD reference board. This allows the boot messages to
be shown on the video display.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8610hpcd_set_pixel_clock() calculates the correct value of the PXCLK
bits in the CLKDVDR register for a given pixel clock rate. The code which
performs this calculation is overly complicated and includes an error
estimation routine that doesn't work most of the time anyway. Replace the
code with the simpler routine that's currently used on the P1022DS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable framebuffer console support by default in the defconfigs for the
Freescale 85xx-based reference board. This allows the boot messages to
be shown on the video display on the P1022DS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To ensure that the DIU pixel clock will not be set to an invalid value,
clamp the PXCLK divider to the allowed range (2-255). This also acts as
a limiter for the pixel clock.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e500mc cannot doze or nap due to an erratum (as well as having a
different mechanism than previous e500), but it has a "wait" instruction
that is similar to doze.
On 64-bit, due to the soft-irq-disable mechanism, the existing
book3e_idle should be used instead.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The platform file for the Freecale P1022DS reference board is not freeing
the ioremap() mapping of the PIXIS and global utilities nodes it creates.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl-lbc driver requires an interrupt to bind to localbus device.
Populate 85xx boards' dts trees with lbc interrupt info.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller can act as agent(EP) or host(RC). Under Agent(EP) mode
the controller will be configured by the host system. So its not required
to be registered with the PCI(e) sub-system. We only register the
controller if its configured in host(RC) mode.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the ePAPR-compliant Freescale hypervisor (aka "Topaz") on
the Freescale P3041DS, P4080DS, and P5020DS reference boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add functions to restart and halt the current partition when running under
the Freescale hypervisor. These functions should be assigned to various
function pointers of the ppc_md structure during the .probe() function for
the board:
ppc_md.restart = fsl_hv_restart;
ppc_md.power_off = fsl_hv_halt;
ppc_md.halt = fsl_hv_halt;
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale ePAPR reference hypervisor provides interrupt controller
services via a hypercall interface, instead of emulating the MPIC
controller. This is called the VMPIC.
The ePAPR "virtual interrupt controller" provides interrupt controller
services for external interrupts. External interrupts received by a
partition can come from two sources:
- Hardware interrupts - hardware interrupts come from external
interrupt lines or on-chip I/O devices.
- Virtual interrupts - virtual interrupts are generated by the hypervisor
as part of some hypervisor service or hypervisor-created virtual device.
Both types of interrupts are processed using the same programming model and
same set of hypercalls.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ePAPR hypervisors provide operating system services via a "hypercall"
interface. The following steps need to be performed to make an hcall:
1. Load r11 with the hcall number
2. Load specific other registers with parameters
3. Issue instrucion "sc 1"
4. The return code is in r3
5. Other returned parameters are in other registers.
To provide this service to the kernel, these steps are wrapped in inline
assembly functions. Standard ePAPR hcalls are in epapr_hcalls.h, and
Freescale extensions are in fsl_hcalls.h.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move irq_choose_cpu() into arch/powerpc/kernel/irq.c so that it can be used
by other PIC drivers. The function is not MPIC-specific.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need the FSL specific header fixup code on both 32-bit and 64-bit
platforms so just move the code into pci-common.c.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture. This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We expect this is actually faster, and we end up needing more space than we
can get from the SPRGs in some instances. This is also useful when running
as a guest OS - SPRGs4-7 do not have guest versions.
8 slots are allocated in thread_info for this even though we only actually
use 4 of them - this allows space for future code to have more scratch
space (and we know we'll need it for things like hugetlb).
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In cases like when the platform is used under hypervisor we will NOT
have an MPIC controller but still want doorbells setup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We fixup every FSL PCIe Root Complex we need to fixup a few things.
Rather than adding every device under the sun we move to just matching
only on the vendor (PCI_VENDOR_ID_FREESCALE) and than check that we are
a PCIe controller in host mode in the fixup.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
