We don't use any CPM devices on these boards, but the muram node on these
chips is different from the 8560, so it's helpful to people working with
custom boards based on these chips.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DTC now supports "foo","bar" format for lists of strings; use the new
format on the lite5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. UCC1's RX_DV pin is 16, not 15;
2. UCC1's phy is at 0x7, not 0x1. Schematics says 0x7, and recent
u-boot also using 0x7.
3. Use gianfar's (eTSEC) mdio bus. This is hardware default setup.
4. tx-clock should be CLK16 (GE125, PB31);
5. phy-connection-type is RGMII-ID;
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the majority of 85xx & 86xx we have a register that's ability to
assert HRESET_REQ to reset the board. We refactored that code so it
can be shared between both platforms into fsl_soc.c and removed all
the duplication in each platform directory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to booting-without-of.txt, compatible should be "fsl_spi" and
mode "cpu" or "qe" for the fsl SPI controllers.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI nodes on the MPC8568 dts didn't get moved up to be sibilings of the
SOC node when we did that clean up for some reason. Fix that up and some
minor whitespace and adjusting the size of the soc reg property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8568E-MDS have DS1374 chip on the I2C bus, thus let's use it.
This patch also adds #address-cells and #size-cells to the I2C
controllers nodes.
p.s. DS1374 rtc class driver is in the -mm tree, its name is
rtc-rtc-class-driver-for-the-ds1374.patch.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The way the current CPM binding describes available multi-user (a.k.a.
dual-ported) RAM doesn't work well when there are multiple free regions,
and it doesn't work at all if the region doesn't begin at the start of
the muram area (as the hardware needs to be programmed with offsets into
this area). The latter situation can happen with SMC UARTs on CPM2, as its
parameter RAM is relocatable, u-boot puts it at zero, and the kernel doesn't
support moving it.
It is now described with a muram node, similar to QE. The current CPM
binding is sufficiently recent (i.e. never appeared in an official release)
that compatibility with existing device trees is not an issue.
The code supporting the new binding is shared between cpm1 and cpm2, rather
than remain separated. QE should be able to use this code as well, once
minor fixes are made to its device trees.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. PCI and reset are factored out into pq2.c. I renamed them from m82xx
to pq2 because they won't work on the Integrated Host Processor line of
82xx chips (i.e. 8240, 8245, and such).
2. The PCI PIC, which is nominally board-specific, is used on multiple
boards, and thus is used into pq2ads-pci-pic.c.
3. The new CPM binding is used.
4. General cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It now uses the new CPM binding and the generic pin/clock functions, and
has assorted fixes and cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Setup dr_mode for USB-DR to peripheral as the default (host mode) doesn't make
much sense for the mini-AB connector on the ITX board.
Peripheral mode is preferable to OTG as the fsl_usb2_udc.c driver doesn't yet
properly support it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to PowerPC 440EPx documentation,
MAL0 is comprised of four channels (two transmit and two receive).
Each channel is dedicated to one of two EMAC cores.
This patch fixes Sequoia DTS MAL0 entry and EMAC entries,
assigning correct channel numbers to EMACs.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A new binding for flash devices was recently introduced. This updates the
Sequoia DTS to use the new binding and enabled MTD in the defconfig.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Stefan Roese <sr@denx.de>
A new binding for flash devices was recently introduced. This updates the
Walnut DTS to use the new binding.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Enabled using SPI controller on the MPC832x RDB board. We currently use
a modalias of "spidev" as a place holder (replace with "mmc_spie") until
the mmc_spi driver support is merged in.
This gets us the ability to test SPI until then.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the device trees to have the PCI nodes be at the same level as
the SOC node. This is to make it so that the SOC nodes children address
space is just on chip registers and not other bus memory as well.
Also, for PCIe nodes added a P2P bridge to handle the virtual P2P bridge
that exists in the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the following cruft from .dts files:
* 32-bit in cpu node -- doesn't exist in any spec and not used by kernel
* removed built-in (chrp legacy)
* Removed #interrupt-cells in places they don't need to be set
* Fixed ranges on lite5200*
* Removed clock-frequency from i8259 pic node, not sure where this came from
* Removed big-endian from i8259 pic nodes, this was just bogus
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added basic board port for MPC8572 DS reference platform that is
similiar to the MPC8544/33 DS reference platform in uniprocessor mode.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. Fix RTC type - it is a rs5c372a, not rs5c372b
2. Configure both UART interrupts edge-triggered
3. Add a license header to ls_uart.c
4. Check for running on linkstation in a late_initcall() function. Needed
for multiplatform builds, even though linkstation doesn't support them
yet
5. Remove unneeded #include from linkstation.c
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This replaces the binding for flash chips in booting-without-of.txt
with an clarified and improved version. It also makes
drivers/mtd/maps/physmap_of.c recognize this new binding. Finally it
revises the Ebony device tree source to use the new binding as an
example.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch below removes the dtc incantation instructions from the
in-kernel DTS files. It's not needed, and is prone to being
out-of-date most of the time.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch contains a handful of small fixes to allow the Ebony's
flash to be exposed as MTD devices via the physmap_of driver.
Specifically it:
- Makes a small addition to the device tree and zImage wrapper
to record the correct address for the flash in the device tree based
on the board switches as reported via an FPGA register.
- Prohibits building the old hard-coded "Ebony" flash map on
arch/powerpc kernels, in favour of using physmap_of's device tree
based approach.
- Enables MTD and physmap_of in the Ebony defconfig.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
This fixes the RTC on linkstation ppc machines again, and updates the
device tree: add rtc nodes on i2c, remove bogus 0-size cache-line
declarations, rename interrupt-controller nodes, remove erroneous
interrupt-parent line, accidentally introduced by a recent patch.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add global-utilities node with has-rstcr on MPC8544 DS and MPC8568 MDS
boards so they are able to reset properly.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8544 dts needed to set the new phy-connection-type to rgmii-id
for the Vitesse PHY on the board to work properly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for arch/powerpc, specifically for the prpmc2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added the P2P bridge present on the Arcadia base board and moved the VIA
Southbridge behind the bridge to reflect its actual position in the bus
organization. Added the RTC that's in the VIA Southbridge and expanded
the ranges array for the SOC node to allow proper address translation of
the RTC registers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
