Consolidate a bunch of C&P code that waits for the firmware to be ready.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 is embedded chip that can be connected using SDIO bus, and is not
an actual SDIO card. For this reason there is a need to pass some board
specific data, like 'EEPROM is attached' flag or power control callback.
However currently there is no way to pass this data through SDIO subsystem,
so this patch registers dummy platform_device to allow that, until we
have a better solution to this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug which was just recently introduced by
("p54pci: prevent stuck rx-ring on slow system").
make M=drivers/net/wireless/p54 C=2 CF=-D__CHECK_ENDIAN__
CHECK drivers/net/wireless/p54/p54pci.c
drivers/net/wireless/p54/p54pci.c:143:11: warning: cast to restricted __le32
CC [M] drivers/net/wireless/p54/p54pci.o
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci used the callback write_tx_desc to write the tx descriptor but
also to update the txwi which is part of the dma mapped skb. Since the
memory was already DMA mapped _before_ the call to write_tx_desc the
device didn't get the txwi data at all or only sporadically.
The call order is basically as follows (from rt2x00queue.c):
1) write_tx_data
2) rt2x00queue_map_txskb
3) write_tx_desc
Hence, we shouldn't touch the skb in write_tx_desc anymore.
To fix this issue create a new rt2800pci_write_tx_data callback and use it
for updating the txwi _before_ the memory gets DMA mapped.
The tx descriptor is still written (as before) in write_tx_desc.
This patch allows basic TX on an rt305x soc device but I'm pretty sure
that it will fix pci based cards as well. I can associate just fine with
an AP now but I wasn't able to get a wpa secured connection working yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend the write_tx_data callback with a txdesc parameter to allow
access to the tx desciptor while preparing the tx data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a scenario, where a cfg80211 driver (station mode) does not send assoc request
and assoc response IEs in cfg80211_connect_result after a successful association
to an AP, cfg80211 sends IWEVASSOCREQIE and IWEVASSOCRESPIE to the user space
application with NULL data. This can cause an issue at the event recipient.
An example of this is when cfg80211 sends IWEVASSOCREQIE and IWEVASSOCRESPIE
events with NULL event body to wpa_supplicant. The wpa_supplicant overwrites
the assoc request and assoc response IEs for this station with NULL data.
If the association is WPA/WPA2, the wpa_supplicant is not able to generate
EAPOL handshake messages, since the IEs are NULL.
With the patch, req_ie and resp_ie will be NULL by avoiding the
assignment if the driver has not sent the IEs to cfg80211. The event sending
code sends the events only if resp_ie and req_ie are not NULL. This
will ensure that the events are not sent with NULL event body.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some wl1251 hardware configurations (like in WG7210 module) have
EEPROM attached where NVS data is kept, which includes MAC address.
In such configurations, let's read default MAC address from EEPROM,
instead of using random one.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Any inode reclaim flush that returns EAGAIN will result in the inode
reclaim being attempted again later. There is no need to issue a
warning into the logs about this situation.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Updates to the VFS layer removed an extra ->sync_fs call into the
filesystem during the sync process (from the quota code).
Unfortunately the sync code was unknowingly relying on this call to
make sure metadata buffers were flushed via a xfs_buftarg_flush()
call to move the tail of the log forward in memory before the final
transactions of the sync process were issued.
As a result, the old code would write a very recent log tail value
to the log by the end of the sync process, and so a subsequent crash
would leave nothing for log recovery to do. Hence in qa test 182,
log recovery only replayed a small handle for inode fsync
transactions in this case.
However, with the removal of the extra ->sync_fs call, the log tail
was now not moved forward with the inode fsync transactions near the
end of the sync procese the first (and only) buftarg flush occurred
after these transactions went to disk. The result is that log
recovery now sees a large number of transactions for metadata that
is already on disk.
This usually isn't a problem, but when the transactions include
inode chunk allocation, the inode create transactions and all
subsequent changes are replayed as we cannt rely on what is on disk
is valid. As a result, if the inode was written and contains
unlogged changes, the unlogged changes are lost, thereby violating
sync semantics.
The fix is to always issue a transaction after the buftarg flush
occurs is the log iѕ not idle or covered. This results in a dummy
transaction being written that contains the up-to-date log tail
value, which will be very recent. Indeed, it will be at least as
recent as the old code would have left on disk, so log recovery
will behave exactly as it used to in this situation.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] max63xx driver depends on ioremap()
[WATCHDOG] max63xx: be careful when disabling the watchdog
[WATCHDOG] fixed book E watchdog period register mask.
[WATCHDOG] omap4: Fix WDT Kconfig
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: imx-ssi: do not call hrtimer_disable in trigger function
ALSA: hda - Add position_fix quirk for Biostar mobo
ALSA: hda - add a quirk for Clevo M570U laptop
ASoC: imx-ssi: increase minimum periods to 4
ALSA: hda - Avoid invalid "Independent HP" control for VIA codecs
ALSA: hda - Fix control element allocations in VIA codec parser
ALSA: aaci - Fix alignment faults on ARM Cortex introduced by commit 29a4f2d3
ALSA: hda - Add fix-up for Sony VAIO with ALC269
ALSA: hda - Enhance fix-up table for Realtek codecs
ALSA: usb - Fix Oops after usb-midi disconnection
ALSA: hda - Fix initial capture source connections of ALC880/260
ALSA: hda - Fix setup for ALC269vb amic and dmic models
ALSA: hda - Fix auto-parser of ALC269vb for HP pin NID 0x21
ASoC: imx-ssi: Use a hrtimer in FIQ mode
ASoC: imx-pcm-dma-mx2: restart DMA after an error
ASoC: imx-ssi: honor IMX_SSI_DMA flag
ASoC: wm2000: remove unused #include <linux/version.h>
ALSA: hda: Add support for Medion WIM2160
Correct fix for the "ioremap() causes build failure on S390" should have been
a dependancy on HAS_IOMEM. So we add this dependancy also (and leave the driver
in the ARM section for now).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When shutting down the watchdog timer, special care must be taken
not to overwrite other bits in the register, as it may be shared
with other peripherals.
For example, on the Arcom Vulcan, the register is shared between
the watchdog and the PCI reset line...
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A previous fix changed the WDTP function to use the period directly,
rather than subtracting from 63. However the mask generation was
not changed, so the mask was coming out as 0. This patch fixes it.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch allows Watchdog timer to be selected for OMAP4 by fixing
Kconfig entry
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
As Herbert Xu said: we should be able to simply replace ipfragok
with skb->local_df. commit f88037(sctp: Drop ipfargok in sctp_xmit function)
has droped ipfragok and set local_df value properly.
The patch kills the ipfragok parameter of .queue_xmit().
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f88037(sctp: Drop ipfargok in sctp_xmit function)
has droped ipfragok and set local_df value properly.
So the change of commit 77e2f1(ipv6: Fix ip6_xmit to
send fragments if ipfragok is true) is not needed.
So the patch remove them.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris got following trace with a linux-next kernel
[ 14.203970] BUG: using smp_processor_id() in preemptible [00000000]
code: avahi-daemon/2093
[ 14.204025] caller is netif_rx+0xfa/0x110
[ 14.204035] Call Trace:
[ 14.204064] [<ffffffff81278fe5>] debug_smp_processor_id+0x105/0x110
[ 14.204070] [<ffffffff8142163a>] netif_rx+0xfa/0x110
[ 14.204090] [<ffffffff8145b631>] ip_dev_loopback_xmit+0x71/0xa0
[ 14.204095] [<ffffffff8145b892>] ip_mc_output+0x192/0x2c0
[ 14.204099] [<ffffffff8145d610>] ip_local_out+0x20/0x30
[ 14.204105] [<ffffffff8145d8ad>] ip_push_pending_frames+0x28d/0x3d0
[ 14.204119] [<ffffffff8147f1cc>] udp_push_pending_frames+0x14c/0x400
[ 14.204125] [<ffffffff814803fc>] udp_sendmsg+0x39c/0x790
[ 14.204137] [<ffffffff814891d5>] inet_sendmsg+0x45/0x80
[ 14.204149] [<ffffffff8140af91>] sock_sendmsg+0xf1/0x110
[ 14.204189] [<ffffffff8140dc6c>] sys_sendmsg+0x20c/0x380
[ 14.204233] [<ffffffff8100ad82>] system_call_fastpath+0x16/0x1b
While current linux-2.6 kernel doesnt emit this warning, bug is latent
and might cause unexpected failures.
ip_dev_loopback_xmit() runs in process context, preemption enabled, so
must call netif_rx_ni() instead of netif_rx(), to make sure that we
process pending software interrupt.
Same change for ip6_dev_loopback_xmit()
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - switch mode upon system resume
Revert "Input: wacom - merge out and in prox events"
Input: matrix_keypad - allow platform to disable key autorepeat
Input: ALPS - add signature for HP Pavilion dm3 laptops
Input: i8042 - spelling fix
Input: sparse-keymap - implement safer freeing of the keymap
Input: update the status of the Multitouch X driver project
Input: clarify the no-finger event in multitouch protocol
Input: bcm5974 - retract efi-broken suspend_resume
Input: sparse-keymap - free the right keymap on error
When Wacom devices wake up from a sleep, the switch mode command
(wacom_query_tablet_data) is needed before wacom_open is called.
wacom_query_tablet_data should not be executed inside wacom_open
since wacom_open is called more than once during probe.
wacom_retrieve_hid_descriptor is removed from wacom_resume due
to the fact that the required descriptors are stored properly
upon system resume.
Reported-and-tested-by: Anton Anikin <Anton@Anikin.name>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Among else, this allows projects like libdc1394 to carry copies of the
ABI related header files without them or distributors having to worry
about effects on the project's overall license terms. Switch to MIT
license as suggested by Kristian. Also update the year in the
copyright statement according to source history.
Cc: Jay Fenlason <fenlason@redhat.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Fix an oversight in ipmr_destroy_unres() - the net pointer is
unconditionally initialized to NULL, resulting in a NULL pointer
dereference later on.
Fix by adding a net pointer to struct mr_table and using it in
ipmr_destroy_unres().
Signed-off-by: Patrick McHardy <kaber@trash.net>
The patch to convert struct mfc_cache to list_heads (ipv4: ipmr: convert
struct mfc_cache to struct list_head) introduced a bug when adding new
cache entries that don't match any unresolved entries.
The unres queue is searched for a matching entry, which is then resolved.
When no matching entry is present, the iterator points to the head of the
list, but is treated as a matching entry. Use a seperate variable to
indicate that a matching entry was found.
Signed-off-by: Patrick McHardy <kaber@trash.net>
When dev_pick_tx() caches tx queue_index on a socket, we must check
socket dst_entry matches skb one, or risk a crash later, as reported by
Denys Fedorysychenko, if old packets are in flight during a route
change, involving devices with different number of queues.
Bug introduced by commit a4ee3ce3
(net: Use sk_tx_queue_mapping for connected sockets)
Reported-by: Denys Fedorysychenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris reported netif_rx() is calling smp_processor_id() from
preemptible context, in particular when caller is
ip_dev_loopback_xmit().
RPS commit added this smp_processor_id() call, this patch makes sure
preemption is disabled. rps_get_cpus() wants rcu_read_lock() anyway, we
can dot it a bit earlier.
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Biostar mobo seems to give a wrong DMA position, resulting in
stuttering or skipping sounds on 2.6.34. Since the commit
7b3a177b0d, "ALSA: pcm_lib: fix "something
must be really wrong" condition", makes the position check more strictly,
the DMA position problem is revealed more clearly now.
The fix is to use only LPIB for obtaining the position, i.e. passing
position_fix=1. This patch adds a static quirk to achieve it as default.
Reported-by: Frank Griffin <ftg@roadrunner.com>
Cc: Eric Piel <Eric.Piel@tremplin-utc.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
SELinux: Reduce max avtab size to avoid page allocation failures
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: use separate class for ceph sockets' sk_lock
ceph: reserve one more caps space when doing readdir
ceph: queue_cap_snap should always queue dirty context
ceph: fix dentry reference leak in dcache readdir
ceph: decode v5 of osdmap (pool names) [protocol change]
ceph: fix ack counter reset on connection reset
ceph: fix leaked inode ref due to snap metadata writeback race
ceph: fix snap context reference leaks
ceph: allow writeback of snapped pages older than 'oldest' snapc
ceph: fix dentry rehashing on virtual .snap dir
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: stop using KVM hypercall mechanism
lguest: workaround cmpxchg8b_emu by ignoring cli in the guest.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix asm constraints for atomic_sub_and_test() and atomic_add_negative()
m68k: Fix `struct sigcontext' for ColdFire
