to prevent PHY access conflict with APE firmware.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
casting the void pointer is redundant (Documentation/CodingStyle)
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates and fixes from David Miller:
1) Reinstate the no-ref optimization for input route lookups in ipv4 to
fix some routing cache removal perf regressions.
2) Make TCP socket pre-demux work on ipv6 side too, from Eric Dumazet.
3) Get RX hash value from correct place in be2net driver, from
Sarveshwar Bandi.
4) Validation of FIB cached routes missing critical check, from Eric
Dumazet.
5) EEH support in mlx4 driver, from Kleber Sacilotto de Souza.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
ipv6: Early TCP socket demux
ipv4: Fix input route performance regression.
pch_gbe: vlan skb len fix
pch_gbe: add extra clean tx
pch_gbe: fix transmit watchdog timeout
ixgbe: fix panic while dumping packets on Tx hang with IOMMU
be2net: Fix to parse RSS hash from Receive completions correctly.
net/mlx4_en: Limit the RFS filter IDs to be < RPS_NO_FILTER
hyperv: Add error handling to rndis_filter_device_add()
hyperv: Add a check for ring_size value
ipv4: rt_cache_valid must check expired routes
net/pch_gpe: Cannot disable ethernet autonegation
qeth: repair crash in qeth_l3_vlan_rx_kill_vid()
netiucv: cleanup attribute usage
net: wiznet add missing HAS_IOMEM dependency
be2net: Missing byteswap in be_get_fw_log_level causes oops on PowerPC
mlx4: Add support for EEH error recovery
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
wanmain: comparing array with NULL
caif: fix NULL pointer check
...
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
In boards with 4-ports, Tx LPI statistics were gathered incorrectly.
This patch guarantees that each pmf will only query its own port for
these statistics.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57840 boards come in two flavours: 2 x 20G and 4 x 10G.
To better differentiate between the two flavours, a separate device ID
was assigned to each.
The silicon default value is still the currently supported 57840 device ID
(0x168d), and since a user can damage the nvram (e.g., 'ethtool -E')
the driver will still support this device ID to allow the user to amend the
nvram back into a supported configuration.
Notice this patch contains lines longer than 80 characters (strings).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 64 bit stats to Broadcom b44 ethernet driver.
Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the numbers used for stop/resume queue in a single place and
fix the condition for sanity check.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PCI block has reset, the memory enable bit will be reset and
the device will not respond to MMIO access. bnx2_reset_task() currently
will not recover when this happens. Add code to detect this condition
and restore the PCI state. This scenario has been reported by some
users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tg3 devices have management firmware that can export sensor data.
Export temperature sensor reading via hwmon sysfs.
[hwmon interface suggested by Ben Hutchings <bhutchings@solarflare.com>]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for retreiving temperature sensor data.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by refactoring code in tg3_ape_send_event(). The common function will
be used in subsequent patches.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently skips setting this flag if the VPD contains the
firmware version string. We fix this by separating the probing of NCSI
from the reading of the NCSI version string. The APE_HAS_NCSI flag is
needed to properly read sensor data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Apple Thunderbolt ethernet device is already listed in the driver,
but not hooked up in the MODULE_DEVICE_TABLE(). This fixes that and
allows it to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, bnx2x_free_tx_skbs() can unmap the wrong DMA address
when it gets to the last entry of the tx ring. We were not using
the proper macro to skip the last entry when advancing the tx index.
Reported-by: Zongyun Lai <zlai@vmware.com>
Reviewed-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert doxygen (or similar) formatted comments to kernel-doc or
unformatted comment. Delete a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If list_for_each_entry, etc complete a traversal of the list, the iterator
variable ends up pointing to an address at an offset from the list head,
and not a meaningful structure. Thus this value should not be used after
the end of the iterator. There does not seem to be a meaningful value to
provide to netdev_warn. Replace with pr_warn, since pr_err is used
elsewhere.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
l4_rxhash is set on skb when rxhash is obtained from canonical 4-tuple
over transport ports/addresses.
We can set skb->l4_rxhash for all incoming TCP packets on bnx2x for
free, as cqe status contains a hash type information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c0357e975a
bnx2: stop using net_device.{base_addr, irq}.
removed netdev->base_addr so we need to update cnic to get the MMIO
base address from pci_resource_start(). Otherwise, mmap of the uio
device will fail.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a1c7fff7e1 (net: netdev_alloc_skb() use build_skb()) broke b44 on
some 64bit machines.
It appears b44 and b43 use __netdev_alloc_skb() instead of alloc_skb()
for their bounce buffers.
There is no need to add an extra NET_SKB_PAD reservation for bounce
buffers :
- In TX path, NET_SKB_PAD is useless
- In RX path in b44, we force a copy of incoming frames if
GFP_DMA allocations were needed.
Reported-and-bisected-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1f85d58cdf
cnic: Remove uio mem[0].
introduced a regression as older versions of userspace app still rely
on this mmap. Restore the mmap functionality and get the base address
from pci_resource_start() as the nedev->base_addr has been deprecated for
PCI devices.
Update version to 2.5.12.
Signed-off-by: Michael Chan <mchan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to indicate that the mising break statements are intended.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware returns error status, proceed to close the iSCSI connection.
Update version to 2.5.11.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This memory region is no longer used. Userspace gets the BAR address
directly from sysfs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so that it will work on any hypervisor.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We register with bnx2x before we allocate ctx_tbl structure, so it is
possible for bnx2x to call cnic_ctl before the structure is allocated.
This can sometimes cause NULL pointer dereference of cp->ctx_tbl. We
fix this by adding simple checking for valid state before proceeding.
The cnic_ctl call is RCU protected so we don't have to deal with race
conditions.
Because of the additional checking, we need to finish the shutdown
before clearing the CNIC_UP flag.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the definition of bnx2x_tests_str_arr from char to static
char. This correction will also eliminate the sparse warning created in commit
cf2c1df62e.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. When FCoE offload driver is registered, copy its capabilities to the chip
scratchpad.
2. Copy FCoE/iSCSI MAC addresses in aligned manner to chip scratchpad.
3. Add FCoE/iSCSI statistics collection support
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ethtool functionality of accessing optic modules'
information and eeprom to the bnx2x driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically lower requested link speed to 1G in case 1G SFP+
module is detected.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a semantic change, cleaning some sections in which the bnx2x
handles the phy's registers.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does several things:
1. Add static to function when possible.
2. Correct comments.
3. Change msleep(small) --> usleep_range(small, small*2).
Also correct existing calls to usleep_range.
4. Remove dead code.
5. Change 'if(rc != 0)' --> if(rc)
Most of these changes are purely semantic.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the ability to identify sfp+ modules' Tx fault, and when such
occur shut down the link.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the date and version of the bnx2x driver.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function device, allow configuring dcbx admin params from all drivers
on a single physical port.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool -L/-l for setting and getting the number of RSS queues.
The 'combined' field is used as we don't support separate IRQ for Rx and Tx.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removed the limitation in the code for 16 RSS queues.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves some fields out of the FP structure to different structures, in
order to minimize size of contigiuous memory allocated.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the CNIC-related L2 CIDs (for sending control FCoE / iSCSI packets)
were at fixed position, according to the maximal number of RSS queues multiplied
by the number of traffic-classes. This change makes the CIDs dynamic, as they
are defined to be right after the highest RSS CID. This decreases the memory
allocated for the context.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current scheme the transmission queues of traffic-class 0 were 0-15, the
transmission queues of traffic-class 1 were 16-31 and so on. If the number of
RSS queues was smaller than 16, there were gaps in transmission queues
numbering, as well as in CIDs numbering. This is both a waste (especially when
16 is increased to 64), and may causes problems with flushing queues when
reducing the number of RSS queues (using ethtool -L). The new scheme eliminates
the gaps.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With increased number of RSS queues, each multiplied by the number of traffic-
classes, we may have up to 64*3=192 CIDs. The current driver scheme with regard
to context allocation supports only 64 CIDs. The new scheme enables scatter-
gatehr list of pages for the context.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
