After resetting BCM54618se, link partner would still see link since the PHY wasn't put into low-power state.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix no-link issue on BCM578xx when direct attached cable is connected since Warpcore microcode restart was missing to re-read the new mode.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix resolve two problems seen regarding LED:
1. LED doesn't flash during port identification.
2. Traffic LED sometimes do not blink.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix couple of issues of remote fault detection and handling:
Link may go down due to remote fault indications during link establishment.
Possible link down after primary function migration.
Remote fault was not detected on 578xx.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem in which the 578xx chip hangs after running traffic, and then pulling the network cable.
This occurs since TX pipe is stalled due to missing XON indication towards the NIG.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link speed is 1G and below, pause weren't sent due to missing pause setting in the UMAC.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem: HW DDP context was not invalidated in case of ABORTS, etc...
This leads to the problem where memory pages which are used for DDP
as user descriptor could get reused for some other purpose (such as to
satisfy new memory allocation request either by kernel or user mode threads)
and since HW DDP context was not invalidated, HW continue to write to
those pages, hence causing memory corruption.
Fix: Either on incoming ABORTS or due to exchange time out, allowed the
target to cleanup HW DDP context if it was setup for respective ft_cmd.
Added new function to perform this cleanup, furthur it can be enhanced
for other cleanup activity. Fix ft_recv_write_data() to properly handle
fc_frame_payload_get to return pointer to payload if it exist. If there is
no payload which is most common case (+ve case in case if DDP is working
as expected, it will return NULL. Yes, scope of buf is limited to printk.
Invalidation of HW context (which is done inside ft_invl_hw_context() is
necessary in SUCCESS and FAILURE case of DDP. Hence invalidation is DONE
as long as there was DDP setup (whether it worked correctly or not,
NOTE: For some reason, if there is any error w.r.t DDP such as out of
order packet reception, HW simply post the full packet in rx queue.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Cc: Robert W Love <robert.w.love@intel.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
* 'tools-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
tools/power turbostat: fit output into 80 columns on snb-ep
tools/power x86_energy_perf_policy: fix print of uninitialized string
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits)
ACPI: delete stale reference in kernel-parameters.txt
ACPI: add missing _OSI strings
ACPI: remove NID_INVAL
thermal: make THERMAL_HWMON implementation fully internal
thermal: split hwmon lookup to a separate function
thermal: hide CONFIG_THERMAL_HWMON
ACPI print OSI(Linux) warning only once
ACPI: DMI workaround for Asus A8N-SLI Premium and Asus A8N-SLI DELUX
ACPI / Battery: propagate sysfs error in acpi_battery_add()
ACPI / Battery: avoid acpi_battery_add() use-after-free
ACPI: introduce "acpi_rsdp=" parameter for kdump
ACPI: constify ops structs
ACPI: fix CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS
ACPI: fix 80 char overflow
ACPI / Battery: Resolve the race condition in the sysfs_remove_battery()
ACPI / Battery: Add the check before refresh sysfs in the battery_notify()
ACPI / Battery: Add the hibernation process in the battery_notify()
ACPI / Battery: Rename acpi_battery_quirks2 with acpi_battery_quirks
ACPI / Battery: Change 16-bit signed negative battery current into correct value
ACPI / Battery: Add the power unit macro
...
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile/mm/init.c: trivial: use BUG_ON
arch/tile: remove useless set_fixmap_nocache() macro
arch/tile: add hypervisor-based character driver for SPI flash ROM
ioctl-number.txt: add the tile hardwall ioctl range
tile: use generic-y format for one-line asm-generic headers
clocksource: tile: convert to use clocksource_register_hz
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (31 commits)
Btrfs: don't call writepages from within write_full_page
Btrfs: Remove unused variable 'last_index' in file.c
Btrfs: clean up for find_first_extent_bit()
Btrfs: clean up for wait_extent_bit()
Btrfs: clean up for insert_state()
Btrfs: remove unused members from struct extent_state
Btrfs: clean up code for merging extent maps
Btrfs: clean up code for extent_map lookup
Btrfs: clean up search_extent_mapping()
Btrfs: remove redundant code for dir item lookup
Btrfs: make acl functions really no-op if acl is not enabled
Btrfs: remove remaining ref-cache code
Btrfs: remove a BUG_ON() in btrfs_commit_transaction()
Btrfs: use wait_event()
Btrfs: check the nodatasum flag when writing compressed files
Btrfs: copy string correctly in INO_LOOKUP ioctl
Btrfs: don't print the leaf if we had an error
btrfs: make btrfs_set_root_node void
Btrfs: fix oops while writing data to SSD partitions
Btrfs: Protect the readonly flag of block group
...
Fix up trivial conflicts (due to acl and writeback cleanups) in
- fs/btrfs/acl.c
- fs/btrfs/ctree.h
- fs/btrfs/extent_io.c
* 'devicetree/next' of git://git.secretlab.ca/git/linux-2.6:
MAINTAINERS: Add keyword match for of_match_table to device tree section
of: constify property name parameters for helper functions
input: xilinx_ps2: Add missing of_address.h header
of: address: use resource_size helper
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-watchdog:
watchdog: Cleanup WATCHDOG_CORE help text
watchdog: Fix POST failure on ASUS P5N32-E SLI and similar boards
watchdog: shwdt: fix usage of mod_timer
Input close or device disable should not interact with the exported
gpiolib functionality. However that's the case. __ad7879_disable()
clears the entire AD7879_REG_CTRL2, while it should just power down
the ADC and its reference.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
the only potentially subtle thing here: get_cached_acl()
is never called with the second argument other than
ACL_TYPE_{ACCESS,DEFAULT}. IOW, that return ERR_PTR(-EINVAL)
in there might as well be BUG().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Don't use floating point on Niagara2, use the traditional
plain Niagara code instead.
Unroll Niagara loops to 128 bytes for copy, and 256 bytes
for clear.
Signed-off-by: David S. Miller <davem@davemloft.net>
cifs: demote DFS referral lookup errors to cFYI
Now that we call into this routine on every mount, anyone who doesn't
have the upcall configured will get multiple printks about failed lookups.
Reported-and-Tested-by: Martijn Uffing <mp3project@sarijopen.student.utwente.nl>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Cache handling in this driver is broken. The chip has 16-bit registers, yet the
register numbers also increase by 2 per register, i.e. there are only
even-numbered registers. The cache in this driver, though, simply increments
register numbers, so it does need some mapping as seen in
sgtl5000_restore_regs(), note the '>> 1':
snd_soc_write(codec, SGTL5000_CHIP_LINREG_CTRL,
cache[SGTL5000_CHIP_LINREG_CTRL >> 1]);
That, of course, won't work with snd_soc_update_bits(). (Thus, we won't even
notice the missing register 0x1c in the default regs which shifted all follwing
registers to wrong values.) Noticed on the MX28EVK where enabling the regulators
simply locked up the chip.
Refactor the routines and use a properly sized default_regs array which matches
the register layout of the underlying chip, i.e. create a truly flat cache.
This also saves some code which should make up for the bigger array a little.
When soc-core will somewhen have another cache type which handles a step size,
this conversion will also ease the transition.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Dong Aisheng <b29396@freescale.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
In this code, blkvsc_req is allocated in the cache blkdev->request_pool,
but freed in the first case to the cache blkvsc_req->dev->request_pool.
blkvsc_req->dev is subsequently initialized to blkdev, making these the
same at the second call to kmem_cache_free. But at the point of the first
call, blkvsc_req->dev is NULL. The second call is changed too, for
uniformity.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,e,e1,e2,e3;
@@
x = \(kmem_cache_alloc\|kmem_cache_zalloc\)(e1,e2)
... when != x = e
(
kmem_cache_free(e1,x);
|
?-kmem_cache_free(e3,x);
+kmem_cache_free(e1,x);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a note about the abuse of the clk API to the nvec/TODO list.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert array index from the loop bound to the loop index.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,ar;
@@
for(e1 = 0; e1 < e2; e1++) { <...
ar[
- e2
+ e1
]
...> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x86_64 allmodconfig:
In file included from arch/x86/include/asm/uaccess.h:572,
from include/linux/uaccess.h:5,
from drivers/staging/speakup/devsynth.c:4:
In function 'copy_from_user',
inlined from 'speakup_file_write' at drivers/staging/speakup/devsynth.c:28:
arch/x86/include/asm/uaccess_64.h:64: error: call to 'copy_from_user_overflow' declared with attribute error: copy_from_user() buffer size is not provably correct
I'm not sure what was unprovable about it, but size_t is the correct type
anyway.
Also replace needless min_t() with min()
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This code was cut and pasted in several places. It's missing some
unlocks on error.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Seen during an allmodconfig build for sparc:
CC [M] drivers/staging/ft1000/ft1000-pcmcia/ft1000_proc.o
In file included from drivers/staging/ft1000/ft1000-pcmcia/ft1000_proc.c:26:
drivers/staging/ft1000/ft1000-pcmcia/ft1000.h: In function 'ft1000_read_reg':
drivers/staging/ft1000/ft1000-pcmcia/ft1000.h:80: error: implicit declaration of function 'inw'
drivers/staging/ft1000/ft1000-pcmcia/ft1000.h: In function 'ft1000_write_reg':
drivers/staging/ft1000/ft1000-pcmcia/ft1000.h:86: error: implicit declaration of function 'outw'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The private object support has migrated from gma500 into the DRM core,
remove our now clashing copy so -next can build.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This avoids tainting the kernel as if a proprietary module was loaded.
The kernel will still be tainted because this is a staging driver.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
zcache is only building tmem.c and not building zcache.c. To keep the
module name, zcache.c must be renamed if symbols from tmem.c are to
remain unexported.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce columns for package number to 1.
If you can afford more than 9 packages,
you can also afford a terminal with more than 80 columns:-)
Also shave a column also off the package C-states
Signed-off-by: Len Brown <len.brown@intel.com>
