Commit Graph

48 Commits

Author SHA1 Message Date
Haavard Skinnemoen
89e5785fc8 [PATCH] Atmel MACB ethernet driver
Driver for the Atmel MACB on-chip ethernet module.

Tested on AVR32/AT32AP7000/ATSTK1000. I've heard rumours that it works
with AT91SAM9260 as well, and it may be possible to share some code with
the at91_ether driver for AT91RM9200.

Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682

Changes since previous version:
  * Probe for PHY ID instead of depending on it being provided through
    platform_data.
  * Grab initial ethernet address from the MACB registers instead
    of depending on platform_data.
  * Set MII/RMII mode correctly.

These changes are mostly about making the driver more compatible with
the at91 infrastructure.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:12:04 -05:00
Zang Roy-r61911
5e123b844a [PATCH] Add tsi108/9 On Chip Ethernet device driver support
Add tsi108/9 on chip Ethernet controller driver support.

The driver code collects the feedback of previous posting form the mailing
list and gives the update.

MPC7448HPC2 platform in arch/powerpc uses tsi108 bridge.

The following is a brief description of the Ethernet controller:

The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1.  It uses a single Management interface to
manage the two physical connection devices (PHYs).  Each Ethernet port has
its own statistics monitor that tracks and reports key interface
statistics.  Each port supports a 256-entry hash table for address
filtering.  In addition, each port is bridged to the Switch Fabric through
a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.

Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows.  The Ethernet DMA channels use
descriptors set up in memory, the memory map of the device, and access via
the Switch Fabric.  The Ethernet Controller’s DMA arbiter handles
arbitration for the Switch Fabric.  The Controller also has a register bus
interface for register accesses and status monitor control.

The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes.  The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs.  Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each

Ethernet port uses its transmit and receive DMA channels to manage data
flows through buffer descriptors that are predefined by the system (the
descriptors can exist anywhere in the system memory map).  These
descriptors are data structures that point to buffers filled with data
ready to transmit over Ethernet, or they point to empty buffers ready to
receive data from Ethernet.

Signed-off-by: Alexandre Bounine <Alexandre.Bounine@tundra.com>
Signed-off-by: Roy Zang	<tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:12:03 -05:00
Amit S. Kale
3d396eb17e Add NetXen 1G/10G ethernet driver.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:11:58 -05:00
Al Viro
3470cb1d4f [PATCH] 8390 fixes - the final chunk (h8300)
The rest of 8390 conversions; ifdef cascade in 8390.h is gone now.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:11:56 -05:00
Al Viro
8c6270f957 [PATCH] 8390 fixes - m68k oddballs
more 8390 conversions - mac8390, zorro8390 and hydra got the same treatment
as arm etherh; one more case in 8390.h ifdef cascade is gone.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:11:56 -05:00
Al Viro
6c3561b0c1 [PATCH] beginning of 8390 fixes - generic and arm/etherh
etherh and a handful of other odd drivers use different macros when building
8390.c.  Since we generate a single 8390.o and then link with it, in any
config with both oddball and normal 8390-based driver we will end up with
breakage in at least one of them.  Solution: take most of 8390.c into
lib8390.c and have 8390.c, etherh.c and the rest of oddballs #include it.
Helper macros are taken from 8390.h to whoever includes lib8390.c.  That
way odd drivers get separate instances of compiled 8390 stuff and stop
stepping on each other's toes.  8390.h gets cleaned up - we don't have
the cascade of ifdefs in there and are left with the stuff that can be
used by any 8390-based driver.  Current problems are exactly because of
that cascade - we attempt to choose the set of helpers by looking at config
and that, of course, doesn't work well when we have several sets needed
by various drivers in our config.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:11:56 -05:00
Ralf Baechle
ff2a2e0172 [NET] GT96100: Delete bitrotting ethernet driver
Code for the EV96100 evaluation board hasn't compiled since at least
November 15, 2003, so it is being deleted as of 2.6.18 due to lack of
a user base.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-22 20:15:30 -04:00
Jan-Bernd Themann
7a29108322 [PATCH] ehea: IBM eHEA Ethernet Device Driver
Hi Jeff,

I fixed the __iomem issue and tested the driver with sparse. Looks good so far.
Thanks for your effort.

Jan-Bernd Themann

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>

 drivers/net/Kconfig             |    9
 drivers/net/Makefile            |    1
 drivers/net/ehea/Makefile       |    6
 drivers/net/ehea/ehea.h         |  447 ++++++
 drivers/net/ehea/ehea_ethtool.c |  294 ++++
 drivers/net/ehea/ehea_hcall.h   |   51
 drivers/net/ehea/ehea_hw.h      |  287 ++++
 drivers/net/ehea/ehea_main.c    | 2654 ++++++++++++++++++++++++++++++++++++++++
 drivers/net/ehea/ehea_phyp.c    |  705 ++++++++++
 drivers/net/ehea/ehea_phyp.h    |  455 ++++++
 drivers/net/ehea/ehea_qmr.c     |  582 ++++++++
 drivers/net/ehea/ehea_qmr.h     |  358 +++++
 12 files changed, 5849 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-13 13:23:52 -04:00
Jeff Garzik
846050dd49 Merge branch 'upstream-fixes' into upstream 2006-08-19 17:45:11 -04:00
Li Yang
ce973b141d [PATCH] Freescale QE UCC gigabit ethernet driver
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g.  MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device.  This patch provides driver for the device.

Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-19 17:44:29 -04:00
Ron Mercer
5a4faa8737 [PATCH] qla3xxx NIC driver
This is a complementary network driver for our ISP4XXX parts.

There is a concurrent effort underway to get the iSCSI driver (qla4xxx)
integrated upstream as well.

I have been through several iterations with the linux-netdev list and have had
much response from Stephen Hemminger.

- Built and tested using kernel 2.6.17-rc4.

- The chip supports two ethernet and two iSCSI functions.

- The functions ql_sem_lock, ql_sem_spinlock, ql_sem_unlock, and
  ql_wait_for_drvr_lock are used to protect resources that are shared across
  the network and iSCSI functions.  This protection is mostly during chip
  initialization and resets, but also include link management.

- The PHY/MII are not exported through ethtool due to the fact that the
  iSCSI function will control the common link at least 50% of the time.

This driver has been through several iterations on the netdev list and we feel
this driver is ready for inclusion in the upstream kernel.

It has been built and tested on x86 and PPC64 platforms.

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-29 00:28:51 -04:00
Ralf Baechle
b6e37e55c2 [PATCH] Cleanup SLHC configuration
Convert selection of serial line header compression to use CONFIG_SLHC
rather than makefile ifeq uglyness.  This makes it easier to select
the SLHC module from other code.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-19 13:50:39 -04:00
Sascha Hauer
92aa674d72 [PATCH] network driver for Hilscher netx
This is a patch for the Hilscher netx builtin ethernet ports. The
netx board support was merged into 2.6.17-git2.
The netx is a arm926 based SoC.

Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

--
 drivers/net/Kconfig             |   11
 drivers/net/Makefile            |    1
 drivers/net/netx-eth.c          |  516 ++++++++++++++++++++++++++++++++++++++++
 include/asm-arm/arch-netx/eth.h |   27 ++
 4 files changed, 555 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22 23:28:05 -04:00
Brice Goglin
0da34b6dfe [PATCH] Add Myri-10G Ethernet driver
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>

 drivers/net/Kconfig                            |   17
 drivers/net/Makefile                           |    1
 drivers/net/myri10ge/Makefile                  |    5
 drivers/net/myri10ge/myri10ge.c                | 2851 +++++++++++++++
 drivers/net/myri10ge/myri10ge_mcp.h            |  205 +
 drivers/net/myri10ge/myri10ge_mcp_gen_header.h |   58
 include/linux/pci_ids.h                        |    1
 7 files changed, 3138 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-24 00:27:31 -04:00
Dustin McIntire
0a0c72c911 [PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ethernet chips
>
> The patch was badly wordwrapped.  Please fix and resend.
>

OK, I've fixed the wrapping and removed the CONFIG_ARM restriction.  I've also did my
best to modify the C style to conform to the comments.

I noticed that the patch is getting ignored by majordomo due to its size >100K.
Should it be broken up somehow to allow posting to the lists?

Signed-off-by: Dustin McIntire <dustin@sensoria.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-20 17:38:39 -04:00
Jens Osterkamp
d97381702d [PATCH] fix spidernet build issue
<unchangelogged>

Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-22 20:28:04 -05:00
Jamal Hadi Salim
253af4235d [NET]: Add IFB (Intermediate Functional Block) network device.
A new device to do intermidiate functional block in a system shared
manner.  To use the new functionality, you need to turn on
qos/classifier actions.

The new functionality can be grouped as:

1) qdiscs/policies that are per device as opposed to system wide.  ifb
allows for a device which can be redirected to thus providing an
impression of sharing.

2) Allows for queueing incoming traffic for shaping instead of
dropping.

Packets are redirected to this device using tc/action mirred redirect
construct. If they are sent to it by plain routing instead then they
will merely be dropped and the stats would indicate that.

Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-01-09 14:16:23 -08:00
Lennert Buytenhek
15d014d131 [PATCH] intel ixp2000 network driver
The way the hardware and firmware work is that there is one shared RX
queue and IRQ for a number of different network interfaces.  Due to this,
we would like to process received packets for every interface in the same
NAPI poll handler, so we need a pseudo-device to schedule polling on.

What the driver currently does is that it always schedules polling for
the first network interface in the list, and processes packets for every
interface in the poll handler for that first interface -- however, this
scheme breaks down if the first network interface happens to not be up,
since netif_rx_schedule_prep() checks netif_running().

sky2 apparently has the same issue, and Stephen Hemminger suggested a
way to work around this: create a variant of netif_rx_schedule_prep()
that does not check netif_running().  I implemented this locally and
called it netif_rx_schedule_prep_notup(), and it seems to work well,
but it's something that probably not everyone would be happy with.

The ixp2000 is an ARM CPU with a high-speed network interface in the
CPU itself (full duplex 4Gb/s or 10Gb/s depending on the IXP model.)
The CPU package also contains 8 or 16 (again depending on the IXP
model) 'microengines', which are somewhat primitive but very fast
and efficient processor cores which can be used to offload various
things from the main CPU.

This driver makes the high-speed network interface in the CPU visible
and usable as a regular linux network device.  Currently, it only
supports the Radisys ENP2611 IXP board, but adding support for other
board types should be fairly easy.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-11-18 13:32:22 -05:00
Andy Fleming
7f7f53168d [PATCH] Gianfar update and sysfs support
This seems to have gotten lost, so I'll resend.

Signed-off-by: Andy Fleming <afleming@freescale.com>

* Added sysfs support to gianfar for modifying FIFO and stashing parameters
* Updated driver to support 10 Mbit, full duplex operation
* Improved comments throughout
* Cleaned up and optimized offloading code
* Fixed a bug where rx buffers were being improperly mapped and unmapped
* (only manifested if cache-coherency was off)
* Added support for using the eTSEC exact-match MAC registers
* Bumped the version to 1.3
* Added support for distinguishing between reduced 100 and 10 Mbit modes
* Modified default coalescing values to lower latency
* Added documentation
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-11-18 13:31:26 -05:00
Jeff Garzik
3b621ee5df Merge branch 'master' 2005-11-11 05:51:24 -05:00
Matt Domsch
b3f9b92a6e [PPP]: add PPP MPPE encryption module
From: Matt Domsch <Matt_Domsch@dell.com>

The patch below implements the Microsoft Point-to-Point Encryption method
as a PPP compressor/decompressor.  This is necessary for Linux clients and
servers to interoperate with Microsoft Point-to-Point Tunneling Protocol
(PPTP) servers (either Microsoft PPTP servers or the poptop project) which
use MPPE to encrypt data when creating a VPN.

This patch differs from the kernel_ppp_mppe DKMS pacakge at
pptpclient.sourceforge.net by utilizing the kernel crypto routines rather
than providing its own SHA1 and arcfour implementations.

Minor changes to ppp_generic.c try to prevent a link from disabling
compression (in our case, the encryption) after it has started using
compression (encryption).

Feedback to <pptpclient-devel@lists.sourceforge.net> please.

Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: James Cameron <james.cameron@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-11-08 09:40:47 -08:00
Jeff Garzik
7211bb9b64 Merge branch 'master' 2005-11-05 15:39:24 -05:00
Pantelis Antoniou
48257c4f16 Add fs_enet ethernet network driver, for several embedded platforms. 2005-10-28 16:25:58 -04:00
Jeff Garzik
9089068785 Merge branch 'master' 2005-10-28 12:17:52 -04:00
Ralf Baechle
dcbf847756 [PATCH] mipsnet: Virtual ethernet driver for MIPSsim.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 drivers/net/Kconfig   |    8 +
 drivers/net/Makefile  |    1
 drivers/net/mipsnet.c |  371 ++++++++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/mipsnet.h |  127 +++++++++++++++++
 4 files changed, 507 insertions(+)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-10-18 18:03:48 -04:00
Jeff Garzik
3c8c7b2f32 Merge branch 'upstream-fixes' 2005-10-03 22:06:19 -04:00
David S. Miller
1f26dac320 [NET]: Add Sun Cassini driver.
Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller

Signed-off-by: David S. Miller <davem@davemloft.net>
2005-09-27 15:24:13 -07:00
Andy Fleming
bb40dcbb0f [netdrvr gianfar] use new phy layer
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-09-23 22:54:21 -04:00
Matt Porter
f89efd523b [PATCH] Add rapidio net driver
Adds an "Ethernet" driver which sends Ethernet packets over the standard
RapidIO messaging.  This depends on the core RIO patch for mailbox/doorbell
access.

Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-09-14 09:18:21 -04:00
Jeff Garzik
d7f6884ae0 Merge /spare/repo/linux-2.6/ 2005-09-14 08:01:25 -04:00
Jens Osterkamp
aaec0fab5f [PATCH] net: add driver for the NIC on Cell Blades
This patch adds a driver for a new 1000 Mbit ethernet NIC.  It is
integrated on the south bridge that is used for our Cell Blades.

The code gets the MAC address from the Open Firmware device tree, so it
won't compile on platforms other than ppc64.

This is the first public release, so I don't expect the first version to
get merged, but I'd aim for integration within the 2.6.13 time frame.

Cc: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-09-06 22:17:49 -04:00
Jeff Garzik
39fbe47377 /spare/repo/netdev-2.6 branch 'chelsio' 2005-08-29 16:53:08 -04:00
Jeff Garzik
c1b054d03f Merge /spare/repo/linux-2.6/ 2005-08-29 16:40:27 -04:00
Jeff Garzik
8aaf226a8e /spare/repo/netdev-2.6 branch 'sis190' 2005-08-29 15:52:56 -04:00
Stephen Hemminger
cd28ab6a4e [PATCH] sky2: new experimental Marvell Yukon2 driver
New driver for the Marvell Yukon2 Gigabit Ethernet chipset.
This driver is based on the skge driver, but using the logic
from the SysKonnect version of the sk98lin driver.
It should support all the Yukon2 chipsets that are available
in many current Intel and AMD motherboards.

The driver does support ethtool, tx and rx checksum, and
tcp segmentation offload.  But it has only been tested for
a short while and is known to stop receiving under heavy load.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-08-17 00:53:12 -04:00
Andy Fleming
00db8189d9 This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-30 19:31:23 -04:00
Francois Romieu
890e8d0a3d [PATCH] sis190: resurrection
Raise the sis190 driver from the dead

The driver handles the integrated network device found on SiS 965L
chipset. It follows the classical (non-napi) interrupt-driven model
and provides minimal ethtool support.

The code comes from a heavy cleanup/rewrite of the original code
which was removed from the kernel on 14/04/2004. Since the r8169
driver does not work too bad and there will probably be (at least)
a few months of improvements/testing/fixing, I made the code as
close as possible to the r8169 one.

Pascal Chapperon <pascal.chapperon@wanadoo.fr> deserves some special
credit for testing and bug-catching. Many thanks to Lars Vahlenberg
as well.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-30 18:20:59 -04:00
Jeff Garzik
a532434395 Merge /spare/repo/linux-2.6/ 2005-06-22 21:50:57 -04:00
2089a0d38b Automatic merge of /spare/repo/netdev-2.6 branch skge 2005-06-04 17:54:39 -04:00
bdb7a3427b Automatic merge of /spare/repo/netdev-2.6 branch remove-drivers 2005-06-04 17:12:32 -04:00
79121839aa Automatic merge of /spare/repo/netdev-2.6 branch dm9000 2005-06-04 17:02:29 -04:00
Michael Chan
b6016b7673 [BNX2]: New Broadcom gigabit network driver.
A new driver bnx2 for Broadcom bcm5706 is available.

The patch also includes new 1000BASE-X advertisement bit definitions in
mii.h

Thanks to David Miller and Jeff Garzik for reviewing and their valuable
feedback.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-05-26 13:03:09 -07:00
Al Viro
f7a3aae172 [PATCH] drivers/net/wireless enabled by wrong option
NET_WIRELESS is only a subset of the stuff in drivers/net/wireless;
NET_RADIO is what covers all of them.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
2005-05-15 22:22:32 -04:00
Christoph Lameter
8199d3a79c [PATCH] A new 10GB Ethernet Driver by Chelsio Communications
A Linux driver for the Chelsio 10Gb Ethernet Network Controller by Chelsio
(http://www.chelsio.com).  This driver supports the Chelsio N210 NIC and is
backward compatible with the Chelsio N110 model 10Gb NICs.  It supports
AMD64, EM64T and x86 systems.

Signed-off-by: Tina Yang <tinay@chelsio.com>
Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Christoph Lameter <christoph@lameter.com>

Adrian said:

- my3126.c is unused (because t1_my3126_ops isn't used anywhere)
- what are the EXTRA_CFLAGS in drivers/net/chelsio/Makefile for?
- $(cxgb-y) in drivers/net/chelsio/Makefile seems to be unneeded
- completely unused global functions:
  - espi.c: t1_espi_get_intr_counts
  - sge.c: t1_sge_get_intr_counts
- the following functions can be made static:
  - sge.c: t1_espi_workaround
  - sge.c: t1_sge_tx
  - subr.c: __t1_tpi_read
  - subr.c: __t1_tpi_write
  - subr.c: t1_wait_op_done

shemminger said:

The performance recommendations in cxgb.txt are common to all fast devices,
and should be in one file rather than just for this device. I would rather
see ip-sysctl.txt updated or a new file on tuning recommendations started.
Some of them have consequences that aren't documented well.
For example, turning off TCP timestamps risks data corruption from sequence wrap.

A new driver shouldn't need so may #ifdef's unless you want to putit on older
vendor versions of 2.4

Some accessor and wrapper functions like:
        t1_pci_read_config_4
        adapter_name
        t1_malloc
are just annoying noise.

Why have useless dead code like:

/* Interrupt handler */
+static int pm3393_interrupt_handler(struct cmac *cmac)
+{
+       u32 master_intr_status;
+/*
+    1. Read master interrupt register.
+    2. Read BLOCK's interrupt status registers.
+    3. Handle BLOCK interrupts.
+*/

Jeff said:

step 1:  kill all the OS wrappers.

 And do you really need hooks for multiple MACs, when only one MAC is
 really supported?  Typically these hooks are at a higher level anyway --
 struct net_device.

From: Christoph Lameter <christoph@lameter

Driver modified as suggested by Pekka Enberg, Stephen Hemminger and Andrian
Bunk.  Reduces the size of the driver to ~260k.

- clean up tabs
- removed my3126.c
- removed 85% of suni1x10gexp_regs.h
- removed 80% of regs.h
- removed various calls, renamed variables/functions.
- removed system specific and other wrappers (usleep, msleep)
- removed dead code
- dropped redundant casts in osdep.h
- dropped redundant check of kfree
- dropped weird code (MODVERSIONS stuff)
- reduced number of #ifdefs
- use kcalloc now instead of kmalloc
- Add information about known issues with the driver
- Add information about authors

Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

diff -puN /dev/null Documentation/networking/cxgb.txt
2005-05-15 19:15:02 -04:00
Sascha Hauer
a1365275e7 [PATCH] DM9000 network driver
This patch adds support for the davicom dm9000 network driver.  The dm9000
is found on some embedded arm boards such as the pimx1 or the scb9328.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>

diff -puN /dev/null drivers/net/dm9000.c
2005-05-15 18:31:07 -04:00
Adrian Bunk
5aa83a4c0a [PATCH] remove two obsolete net drivers
The options FMV18X and SK_G16 do depend on the non-available
  CONFIG_OBSOLETE even in kernel 2.4 - IOW, the last time it was able to
  select them was in kernel 2.2 (or even before).
  
  Since it seems noone misses these drivers, this patch removes them.
  
  Signed-off-by: Adrian Bunk <bunk@stusta.de>
  Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-05-12 22:27:35 -04:00
Stephen Hemminger
baef58b1b0 [netdrvr] new driver skge, for SysKonnect cards 2005-05-12 20:14:36 -04:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00