From: James Cosin <jkosin@intcomgrp.com>
fixes the number of digits to 6 after the decimal point to regain the
significant 0s in the frequency after the decimal point.
Signed-off-by: Steven Miao <realmz6@gmail.com>
The bootloader configures the pins, but has pull bits
set without pull enable bits. While this is harmless,
and won't do anything, it seems to cause confusion at
least for me every time looking at the pin configuration.
Fix it for DT based boot.
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit d16fb25 (ARM: dts: OMAP4460: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP4460 OPP data in
arch/arm/mach-omap2/opp4xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 3027e26 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boards supported upstream all use TWL6040 as audio codec, enable the common
ASoC machine driver by default for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for chip id detection of AM335x PG2.1 Silicon.
Currently omap3xxx_check_revision() detects PG1.0 and PG2.0 only,
this patch extends it by adding PG2.1 Si support.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch adds support for fan control button on Ideapad Z580. This is
the same button as on Z570, but it raises different bit in
VPCCMD_R_SPECIAL_BUTTONS. Also add message to dmesg when unknown button
press detected, it will help adding support for new special buttons.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Tested-by: Ivan Vojtko <nekroman.sk@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
pvpanic device is a qemu simulated device through which guest panic
event is sent to host.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Used PTR_RET function instead of IS_ERR and PTR_ERR.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
SVS151290S series uses handle 0x0163 for keyboard backlight and 0x015B for the graphics switch.
Signed-off-by: Arthur Wirski <awirski@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
New HP laptops start generating new events, and hp-wmi prints unknown
event_ids for them. This patch also removes these messages
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
If krealloc() returns NULL, it *doesn't* free the original. So any code
of the form 'foo = krealloc(foo, …);' is almost certainly a bug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
The error in lis3lv02_poweron() is harmless in the resume path, so
we should ignore it. It is inline with the other usages of lis3lv02_poweron()
and matches the 3.0 code for this routine. This patch is in suse git and
might have missed making it into the mainline.
opensuse - commit id: 66ccdac87c322cf7af12bddba8c805af640b1cff
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
CC: stable@vger.kernel.org 3.8, 3.4, 3.5, 3.2
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
There is a new DELL WMI spec. with new WMI event format.
I'm working on the AIO machines, but I think the new format will apply to
all the Dell's machines, not only for AIO, which will be released later
this year.
The new format of the WMI buffer is shown as below
word 0 - the number of words following in the WMI buffer(not including
this word.
word 1 - the event type
0x0000 - A hot key is pressed or an event occurred
0x000F - A sequence of hot keys are pressed
word 2 and on - the event data
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Add the missing iounmap() before return from omap1_system_dma_init()
in the error handling case.
Also removed platform_device_del() on add resources error case which
cause dup device delete.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If DEBUG_LL and earlyprintk are enabled, and omap-serial.c is compiled
as a module, the kernel boot hangs early as the clocks for serial port
are cut while earlyprintk still uses the port.
The problem is a race between the late_initcall for omap_device (which
idles devices that have no drivers) and the late_initcall in
kernel/printk.c which turns off the earlyconsole. Any printks
that happen between this omap_device late initcall and the earlyconsole
late initcall will crash when accessing the UART.
The fix is to ensure the omap_device initcall happens after the
earlyconsole initcall.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.
Fix the issue by moving the touchscreen before the panel in the SPI
device list.
The patch fixes the following failure:
[ 1.260955] acx565akm spi1.2: invalid display ID
[ 1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[ 1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Beagle xM Rev. Ax/Bx, the USB power enable GPIO logic is
reversed when compared to other revisions i.e. it is
active high instead of active low.
Use the beagle_config.usb_pwr_level flag correctly so that
the power regulator can be configured at runtime.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull InfiniBand/RDMA changes from Roland Dreier:
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (23 commits)
IB/iser: Add support for iser CM REQ additional info
IB/iser: Return error to upper layers on EAGAIN registration failures
IB/iser: Move informational messages from error to info level
IB/iser: Add module version
mlx4_core: Expose a few helpers to fill DMFS HW strucutures
mlx4_core: Directly expose fields of DMFS HW rule control segment
mlx4_core: Change a few DMFS fields names to match firmare spec
mlx4: Match DMFS promiscuous field names to firmware spec
mlx4_core: Move DMFS HW structs to common header file
IB/mlx4: Set link type for RAW PACKET QPs in the QP context
IB/mlx4: Disable VLAN stripping for RAW PACKET QPs
mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level
RDMA/iwcm: Don't touch cmid after dropping reference
IB/qib: Correct qib_verbs_register_sysfs() error handling
IB/ipath: Correct ipath_verbs_register_sysfs() error handling
RDMA/cxgb4: Fix SQ allocation when on-chip SQ is disabled
SRPT: Fix odd use of WARN_ON()
IPoIB: Fix ipoib_hard_header() return value
RDMA: Rename random32() to prandom_u32()
RDMA/cxgb3: Fix uninitialized variable
...
Pull arm64 update from Catalin Marinas:
- Since drivers/irqchip/irq-gic.c no longer has dependencies on arm32
specifics (the 'gic' branch merged), it can be enabled on arm64.
- Enable arm64 support for poweroff/restart (for code under
drivers/power/reset/).
- Fixes (dts file, exception handling, bitops)
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Treat the bitops index argument as an 'int'
arm64: Ignore the 'write' ESR flag on cache maintenance faults
arm64: dts: fix #address-cells for foundation-v8
arm64: vexpress: Add support for poweroff/restart
arm64: Enable support for the ARM GIC interrupt controller
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches.
- introduce a new gloabl lock scheme
- add tracepoints on several major functions
- fix the overall cleaning process focused on victim selection
- apply the block plugging to merge IOs as much as possible
- enhance management of free nids and its list
- enhance the readahead mode for node pages
- address several cretical deadlock conditions
- reduce lock_page calls
The other minor bug fixes and enhancements are as follows.
- calculation mistakes: overflow
- bio types: READ, READA, and READ_SYNC
- fix the recovery flow, data races, and null pointer errors"
* tag 'f2fs-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (68 commits)
f2fs: cover free_nid management with spin_lock
f2fs: optimize scan_nat_page()
f2fs: code cleanup for scan_nat_page() and build_free_nids()
f2fs: bugfix for alloc_nid_failed()
f2fs: recover when journal contains deleted files
f2fs: continue to mount after failing recovery
f2fs: avoid deadlock during evict after f2fs_gc
f2fs: modify the number of issued pages to merge IOs
f2fs: remove useless #include <linux/proc_fs.h> as we're now using sysfs as debug entry.
f2fs: fix inconsistent using of NM_WOUT_THRESHOLD
f2fs: check truncation of mapping after lock_page
f2fs: enhance alloc_nid and build_free_nids flows
f2fs: add a tracepoint on f2fs_new_inode
f2fs: check nid == 0 in add_free_nid
f2fs: add REQ_META about metadata requests for submit
f2fs: give a chance to merge IOs by IO scheduler
f2fs: avoid frequent background GC
f2fs: add tracepoints to debug checkpoint request
f2fs: add tracepoints for write page operations
f2fs: add tracepoints to debug the block allocation
...
Pull Hexagon fixes from Richard Kuo:
"A bug fix and a Kconfig cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
HEXAGON: Remove non existent reference to GENERIC_KERNEL_EXECVE & GENERIC_KERNEL_THREAD
Hexagon: fix register used to call do_work_pending
Commit ff5c9059 (ARM: dts: OMAP3+: Correct gpio #interrupts-cells
property) updated the number of interrupt cells required for configuring
gpios as interrupts for other devices (such as ethernet controllers).
This update allowed the interrupt type (edge, level, etc) to be
configured via device-tree (as described in the
Documentation/devicetree/bindings/gpio/gpio-omap.txt).
This broke ethernet support on the OMAP4 SDP board that defines a gpio
as the ethernet IRQ because the interrupt type (level, edge, etc) was
not getting configured correctly. This board use the ks8851 ethernet
chip which has an active low interrupt. Fix this by defining the gpio
interrupt as active-low in the device-tree binding.
Please note that the OMAP4-VAR-SOM also uses the same ethernet
controller and it is expected it will have the same problem. So the
same fix is also applied to this board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8a965b3baa ("mm, slab_common: Fix bootstrap creation of kmalloc
caches") introduced a regression that caused us to crash early during
boot. The commit was introducing ordering of slab creation, making sure
two odd-sized slabs were created after specific powers of two sizes.
But, if any of the power of two slabs were created earlier during boot,
slabs at index 1 or 2 might not get created at all. This patch makes
sure none of the slabs get skipped.
Tony Lindgren bisected this down to the offending commit, which really
helped because bisect kept bringing me to almost but not quite this one.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike meta data server mounts which support multiple mount points to
the same server via struct nfs_server, data servers support a single connection.
Concurrent calls to setup the data server connection can race where the first
call allocates the nfs_client struct, and before the cache struct nfs_client
pointer can be set, a second call also tries to setup the connection, finds the
already allocated nfs_client, bumps the reference count, re-initializes the
session,etc. This results in a hanging data server session after umount.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
A small bug in this code was causing the ALLMULTI filter to be set
when in fact we were just wanting to program a selective multicast list
to the hardware.
Fix that bug and remove a redundant if condition in the code that
follows.
This fixes wakeup behaviour when multicast WOL is enabled. Previously,
all multicast packets would wake up the system. Now, only those that the
host intended to receive trigger wakeups.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: <stable@vger.kernel.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After unregister_netdevice() call the request is queued and
reg_state is changed to NETREG_UNREGISTERING.
As we check for NETREG_UNREGISTERED state, free_netdev() never
gets executed causing memory leak.
Initialize "dev->destructor" to free_netdev() to free device
data after unregistration.
Cc: <stable@vger.kernel.org>
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the XO-4 with 8787 wireless is woken up due to wake-on-WLAN
mwifiex is often flooded with "not allowed while suspended" messages
and the interface is unusable.
[ 202.171609] int: sdio_ireg = 0x1
[ 202.180700] info: mwifiex_process_hs_config: auto cancelling host
sleep since there is interrupt from the firmware
[ 202.201880] event: wakeup device...
[ 202.211452] event: hs_deactivated
[ 202.514638] info: --- Rx: Data packet ---
[ 202.514753] data: 4294957544 BSS(0-0): Data <= kernel
[ 202.514825] PREP_CMD: device in suspended state
[ 202.514839] data: dequeuing the packet ec7248c0 ec4869c0
[ 202.514886] mwifiex_write_data_sync: not allowed while suspended
[ 202.514886] host_to_card, write iomem (1) failed: -1
[ 202.514917] mwifiex_write_data_sync: not allowed while suspended
[ 202.514936] host_to_card, write iomem (2) failed: -1
[ 202.514949] mwifiex_write_data_sync: not allowed while suspended
[ 202.514965] host_to_card, write iomem (3) failed: -1
[ 202.514976] mwifiex_write_data_async failed: 0xFFFFFFFF
This can be readily reproduced when putting the XO-4 in a loop where
it goes to sleep due to inactivity, but then wakes up due to an
incoming ping. The error is hit within an hour or two.
This issue happens when an interrupt comes in early while host sleep
is still activated. Driver handles this case by auto cancelling host
sleep. However is_suspended flag is still set which prevents any cmd
or data from being sent to firmware. Fix it by clearing is_suspended
flag in this path.
Cc: <stable@vger.kernel.org>
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Register Modification for xLNA board.
* TX gain table modification for zero calibration.
* AUX chain (LNA2) sensitivity enhancement
* Modify diversity bias default setting in INI.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a reset or a channel-change happens, for managed mode,
the HW beacon timers have to be programmed after the TSF has
been synchronized. This is handled via the sync flags.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jake reported that since commit 1672c0e319
"mac80211: start auth/assoc timeout on frame status", he is unable to
connect to his AP, which is configured to use passive channel.
After switch to passive channel 4965 firmware drops any TX packet until
it receives beacon. Before commit 1672c0e3 we waited on channel and
retransmit packet after 200ms, that makes we receive beacon on the
meantime and association process succeed. New mac80211 behaviour cause
that any ASSOC frame fail immediately on iwl4965 and we can not
associate.
This patch restore old mac80211 behaviour for iwl4965, by removing
IEEE80211_HW_REPORTS_TX_ACK_STATUS feature. This feature will be
added again to iwl4965 driver, when different, more complex
workaround for this firmware issue, will be added to the driver.
Cc: stable@vger.kernel.org # 3.9
Bisected-by: Jake Edge <jake@lwn.net>
Reported-and-tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add handling of rx descriptor underflow. This fixes a fault that could
happen on slow machines, where data is received faster than the CPU can
handle. In such a case the device will use up all rx descriptors and
refuse to send any more data before confirming that it is ok. This
patch enables necessary interrupt to discover such a situation and will
handle them by dropping everything in the ring buffer.
Reviewed-by: Michael Buesch <m@bues.ch>
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reproduce steps
1. flood ping from other machine
ping -f -s 41000 IP
2. run below script
while [ 1 ]; do ethtool -s eth0 autoneg off;
sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;
You can see oops in one hour.
The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function ptp_clock_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENOMEM in the irlap_open() error handling case instead
of 0(overwrite to 0 by bfin_sir_startup()), as done elsewhere in this
function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdiobus_register creates a phy_device even if get_phy_device failed
to create it previously. This causes indefinite polling on non-existent
PHYs. This fix makes of_mdio_register rely on get_phy_device to
properly create the device or fail otherwise.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver and firmware sync up through SYNC messages, and the
firmware's affirmative reply to these SYNC messages appears to be the
"Reset" indication received via the status interrupt endpoint. Thus the
driver needs the status interrupt endpoint always active so that the
Reset indication can be received even if the netdev is closed, which is
the case right after device insertion.
If the Reset indication is not received by the driver, it continues
sending SYNC messages to the firmware, which crashes about 10 seconds
later and the device stops responding.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers (sierra_net) need the status interrupt URB
active even when the device is closed, because they receive
custom indications from firmware. Add functions to refcount
the status interrupt URB submit/kill operation so that
sub-drivers and the generic driver don't fight over whether
the status interrupt URB is active or not.
A sub-driver can call usbnet_status_start() at any time, but
the URB is only submitted the first time the function is
called. Likewise, when the sub-driver is done with the URB,
it calls usbnet_status_stop() but the URB is only killed when
all users have stopped it. The URB is still killed and
re-submitted for suspend/resume, as before, with the same
refcount it had at suspend.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rebranded Novatel E371 for AT&T's LTE bands. qmi_wwan should drive this
device, while cdc_ether should ignore it. Even though the USB descriptors
are plain CDC-ETHER that USB interface is a QMI interface.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_close() followed by be_clear() is called as a part of cleanup in the
EEH/AER flow. This patch stops TX in be_close() before cleaning/freeing
up the TX queues in be_clear(). This prevents be_xmit() from being called
while TX queues no longer exist.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
