Secure discard is implemented by Secure Trim if the discard is unaligned
or Secure Erase otherwise.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable the data (busy) timeout for erases and set the MMC_CAP_ERASE
capability.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable MMC to service discard requests. In the case of SD and MMC cards
that do not support trim, discards become erases. In the case of cards
(MMC) that only allow erases in multiples of erase group size, round to
the nearest completely discarded erase group.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kconfig dependency warning for PC8736x_GPIO by restricting it to
X86_32.
warning: (SCx200_GPIO && SCx200 || PC8736x_GPIO && X86) selects NSC_GPIO which has unmet direct dependencies (X86_32)
NSC_GPIO is X86_32 only. The other driver (SCx200_GPIO) that selects
NSC_GPIO is X86_32 only (indirectly, since SCx200 depends on X86_32), so
limit this driver also.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ACPI_PREEMPTION_POINT() logic was introduced in commit 8bd108d
(ACPICA: add preemption point after each opcode parse). The follow up
commits abe1dfab6, 138d15692, c084ca70 tried to fix the preemption logic
back and forth, but nobody noticed that the usage of
in_atomic_preempt_off() in that context is wrong.
The check which guards the call of cond_resched() is:
if (!in_atomic_preempt_off() && !irqs_disabled())
in_atomic_preempt_off() is not intended for general use as the comment
above the macro definition clearly says:
* Check whether we were atomic before we did preempt_disable():
* (used by the scheduler, *after* releasing the kernel lock)
On a CONFIG_PREEMPT=n kernel the usage of in_atomic_preempt_off() works by
accident, but with CONFIG_PREEMPT=y it's just broken.
The whole purpose of the ACPI_PREEMPTION_POINT() is to reduce the latency
on a CONFIG_PREEMPT=n kernel, so make ACPI_PREEMPTION_POINT() depend on
CONFIG_PREEMPT=n and remove the in_atomic_preempt_off() check.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16210
[akpm@linux-foundation.org: fix build]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Francois Valenduc <francois.valenduc@tvcablenet.be>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i2c_client received in probe() should not be kfree()'d.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The i2c_client received in probe() should not be kfree()'d.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The i2c_client received in probe() should not be kfree()'d.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add mfd core driver for TPS6586x PMICs family.
The driver provides I/O access for the sub-device drivers and performs
regstration of the sub-devices based on the platform requirements.
In addition it implements GPIOlib interface for the chip GPIOs.
TODO:
- add interrupt support
- add platform data for PWM, backlight leds and charger
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch is originally done by Carlos Eduardo Aguiar. Original fix is
commit 3305829b2816072b9c8ed01374b205ae4de74027 in
git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
Author modified the fix for mainline version of menelaus.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We are modifying register value instead of return value.
This fix is originally done by Carlos Eduardo Aguiar. Original fix is
commit bb4e91722e29efe31587d2cc664b6def645aecd9 in
git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
Author modified the fix for mainline version of menelaus.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch includes below fixes:
1. fix wm8350_create_cache error path
make sure wm8350->reg_cache is freed in error path.
2. fix wm8350_device_init error path
no need to kfree(wm8350->reg_cache) in the case of goto out.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wm8994_device_init() will return 0 in the case of kzalloc fail
in current implementation.
This patch fixes the return value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the case of goto err2, what we want is to call
platform_device_del() instead of platform_device_unregister().
Otherwise, we call platform_device_put() twice.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch includes below fixes:
1. add a missing iounmap in tc6387xb_probe() error path
2. fix resource reclaim in tc6387xb_remove()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds all remaining definitions that are used by the core driver
to the .c file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is a shiny new mc13783 API function that can be used instead.
While at it refactor the code a bit to reduce code duplication a bit.
This removes the last user of <linux/mfd/mc13783-private.h> and so this
include file can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is needed for the mc13783-adc driver to decide if a touch screen is
connected. If so some channels are not available as generic hwmon inputs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If mfd_add_devices() fail, we need to relese allocated resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8321 is a PMIC for low power, high performance applications. From a
software point of view the device is identical to the WM8320, all the
differences between the two devices are visible only in hardware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some STMPE devices support entering sleep mode automatically on a
specified timeout of inactivity on the I2C bus with the host system.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
platform_get_irq_byname() can return negative results, it is not seen to
unsigned ts_irq. Make it signed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-By: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL6030 supports PWM (Pulse Width Modulator) which is used
to control charging LED. PWM allows for controlling brightness.
This patch implements the APIs required by leds-pwm driver.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a MFD driver for the JZ4740 ADC unit. The driver is used to
demultiplex IRQs and synchronize access to shared registers between the
battery, hwmon and (future) touchscreen driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The debounce times are approximate, they can be selected using the two
input functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This one adds a driver for STMPE touchscreen controllers.
This driver depends on the stmpexxx mfd core driver.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add an input driver for the keypad on STMPE I/O expanders. This driver
uses the common support provided by the STMPE MFD driver.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the GPIOs on STMPE I/O Expanders.
[l.fu@pengutronix.de: fix set direction input]
[l.fu@pengutronix.de: set GPIO alternate function while requesting]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the STMPE family of I/O Expanders from
STMicroelectronics. These devices include upto 24 gpios and a varying
selection of blocks, including PWM, keypad, and touchscreen controllers.
This patch adds the MFD core.
[l.fu@pengutronix.de: fix stmpe811 enable hook]
[l.fu@pengutronix.de: add touchscreen platform data]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch includes below fixes to properly free clk32k clock source:
1. remove a redundant clk_put in t7l66xb_probe error path
2. add missing clk_disable(t7l66xb->clk32k) and clk_put(t7l66xb->clk32k)
to properly free the clock source.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For people to be able to intellingibly decide if they want to enable MFD
drivers or not, we have to give them a much better description of what they
are.
These are now exported via an ops table rather than referenced
directly and so should be staticised.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
platform_device_add_resources may fail, thus add error checking for it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use !x rather than IS_ERR(x) to test the result of kzalloc.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,E;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...)
... when != x = E
- IS_ERR(x)
+ !x
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The registers on the AB8500 are only 8 bits wide, so the content
of the remaining bits is undefined. Let's mask off the undefined
stuff when returning a register in an SPI read.
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The original code had a compile warning:
drivers/mfd/88pm860x-core.c:431: warning: ‘ret’ may be used
uninitialized in this function
It seems like the warning is valid if either pdata or pdata->touch is
NULL.
This patch checks pdata and pdata->touch at the beginning of the
function. That means everything can be pulled in one indent level.
Now all the statements fit within the 80 character limit.
Also at that point the "use_gpadc" variable isn't needed and removing
it simplifies the logic.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Haojian Zhuang <hzhuang1@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In current implementation, there is a memory leak if ab3100_otp_read fail.
And in the case of ab3100_otp_init_debugfs fail, it does not properly remove
sysfs entries.
This patch properly handle above failure cases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix typo error in LED resource of 88pm860x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable discard support in the DM multipath target.
This discard support depends on a few discard-specific fixes to the
block layer's request stacking driver methods.
Discard requests are optional so don't allow a failed discard to trigger
path failures. If there is a real problem with a given path the
barriers associated with the discard (either before or after the
discard) will cause path failure. That said, unconditionally passing
discard failures up the stack is not ideal. This must be fixed once DM
has more information about the nature of the underlying storage failure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
The DM core will submit a discard bio to the stripe target for each
stripe in a striped DM device. The stripe target will determine
stripe-specific portions of the supplied bio to be remapped into
individual (at most 'num_discard_requests' extents). If a given
stripe-specific discard bio doesn't touch a particular stripe the bio
will be dropped.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Update __clone_and_map_discard to loop across all targets in a DM
device's table when it processes a discard bio. If a discard crosses a
target boundary it must be split accordingly.
Update __issue_target_requests and __issue_target_request to allow a
cloned discard bio to have a custom start sector and size.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Optimize sector division: If the number of stripes is a power of two,
we can do shift and mask instead of division.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move sector to stripe translation into a function.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Have the error target respond to a discard request with a hard -EIO
rather than fail the request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Have the zero target silently drop a discard rather than fail the
request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split max_io_len_target_boundary out of max_io_len so that the discard
support can make use of it without duplicating max_io_len code.
Avoiding max_io_len's split_io logic enables DM's discard support to
submit the entire discard request to a target. But discards must still
be split on target boundaries.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename __flush_target to __issue_target_request now that it is used to
issue both flush and discard requests.
Introduce __issue_target_requests as a convenient wrapper to
__issue_target_request 'num_flush_requests' or 'num_discard_requests'
times per target.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow discards to be passed through to linear mappings if at least one
underlying device supports it. Discards will be forwarded only to
devices that support them.
A target that supports discards should set num_discard_requests to
indicate how many times each discard request must be submitted to it.
Verify table's underlying devices support discards prior to setting the
associated DM device as capable of discards (via QUEUE_FLAG_DISCARD).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allocate cipher strings indpendently of struct crypt_config and move
cipher parsing and allocation into a separate function to prepare for
supporting the cryptoapi format e.g. "xts(aes)".
No functional change in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use just one label and reuse common destructor for crypt target.
Parse remaining argv arguments in logic order.
Also do not ignore error values from IV init and set key functions.
No functional change in this patch except changed return codes
based on above.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add devname:mapper/control and MAPPER_CTRL_MINOR module alias
to support dm-mod module autoloading.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
'target_request_nr' is a more generic name that reflects the fact that
it will be used for both flush and discard support.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This change unifies the various checks and finalization that occurs on a
table prior to use. By doing so, it allows table construction without
traversing the dm-ioctl interface.
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement merge method for the snapshot origin to improve read
performance.
Without merge method, dm asks the upper layers to submit smallest possible
bios --- one page. Submitting such small bios impacts performance negatively
when reading or writing the origin device.
Without this patch, CPU consumption when reading the origin on lvm on md-raid0
was 6 to 12%, with this patch, it drops to 1 to 4%.
Note: in my testing, it actually degraded performance in some settings, I
traced it to Maxtor disks having problems with > 512-sector requests.
Reducing the number of sectors to /sys/block/sd*/queue/max_sectors_kb to
256 fixed the read performance. I think we don't have to care about weird
disks that actually degrade performance because of large requests being
sent to them.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change bio-based mapped devices no longer to have a fully initialized
request_queue (request_fn, elevator, etc). This means bio-based DM
devices no longer register elevator sysfs attributes ('iosched/' tree
or 'scheduler' other than "none").
In contrast, a request-based DM device will continue to have a full
request_queue and will register elevator sysfs attributes. Therefore
a user can determine a DM device's type by checking if elevator sysfs
attributes exist.
First allocate a minimalist request_queue structure for a DM device
(needed for both bio and request-based DM).
Initialization of a full request_queue is deferred until it is known
that the DM device is request-based, at the end of the table load
sequence.
Factor DM device's request_queue initialization:
- common to both request-based and bio-based into dm_init_md_queue().
- specific to request-based into dm_init_request_based_queue().
The md->type_lock mutex is used to protect md->queue, in addition to
md->type, during table_load().
A DM device's first table_load will establish the immutable md->type.
But md->queue initialization, based on md->type, may fail at that time
(because blk_init_allocated_queue cannot allocate memory). Therefore
any subsequent table_load must (re)try dm_setup_md_queue independently of
establishing md->type.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Determine whether a mapped device is bio-based or request-based when
loading its first (inactive) table and don't allow that to be changed
later.
This patch performs different device initialisation in each of the two
cases. (We don't think it's necessary to add code to support changing
between the two types.)
Allowed md->type transitions:
DM_TYPE_NONE to DM_TYPE_BIO_BASED
DM_TYPE_NONE to DM_TYPE_REQUEST_BASED
We now prevent table_load from replacing the inactive table with a
conflicting type of table even after an explicit table_clear.
Introduce 'type_lock' into the struct mapped_device to protect md->type
and to prepare for the next patch that will change the queue
initialization and allocate memory while md->type_lock is held.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
drivers/md/dm-ioctl.c | 15 +++++++++++++++
drivers/md/dm.c | 37 ++++++++++++++++++++++++++++++-------
drivers/md/dm.h | 5 +++++
include/linux/dm-ioctl.h | 4 ++--
4 files changed, 52 insertions(+), 9 deletions(-)
When processing barriers, skip the second flush if processing the bio
failed with -EOPNOTSUPP. This can happen with discard+barrier requests.
If the device doesn't support discard, there would be two useless
SYNCHRONIZE CACHE commands. The first dm_flush cannot be so easily
optimized out, so we leave it there.
Previously, -EOPNOTSUPP could be received in dec_pending only with empty
barriers and we ignored that error, assuming the device not supporting
cache flushes has cache always consistent. With the addition of discard
barriers, this -EOPNOTSUPP can also be generated by discards and we
must record it in md->barrier_error for process_barrier.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes hard-coded value for the size of a chunk that includes
disk header for persistent snapshot. It should be changed to existing
macro NUM_SNAPSHOT_HDR_CHUNKS instead of using hard-coded value 1.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use kstrdup when the goal of an allocation is copy a string into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@
- to = kmalloc(strlen(from) + 1,flag);
+ to = kstrdup(from, flag);
... when != \(from = E1 \| to = E1 \)
if (to==NULL || ...) S
... when != \(from = E2 \| to = E2 \)
- strcpy(to, from);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The dm control device does not implement read/write, so it has no use for
seeking. Using no_llseek prevents falling back to default_llseek, which
requires the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch separates the device deletion code from dm_put()
to make sure the deletion happens in the process context.
By this patch, device deletion always occurs in an ioctl (process)
context and dm_put() can be called in interrupt context.
As a result, the request-based dm's bad dm_put() usage pointed out
by Mikulas below disappears.
http://marc.info/?l=dm-devel&m=126699981019735&w=2
Without this patch, I confirmed there is a case to crash the system:
dm_put() => dm_table_destroy() => vfree() => BUG_ON(in_interrupt())
Some more backgrounds and details:
In request-based dm, a device opener can remove a mapped_device
while the last request is still completing, because bios in the last
request complete first and then the device opener can close and remove
the mapped_device before the last request completes:
CPU0 CPU1
=================================================================
<<INTERRUPT>>
blk_end_request_all(clone_rq)
blk_update_request(clone_rq)
bio_endio(clone_bio) == end_clone_bio
blk_update_request(orig_rq)
bio_endio(orig_bio)
<<I/O completed>>
dm_blk_close()
dev_remove()
dm_put(md)
<<Free md>>
blk_finish_request(clone_rq)
....
dm_end_request(clone_rq)
free_rq_clone(clone_rq)
blk_end_request_all(orig_rq)
rq_completed(md)
So request-based dm used dm_get()/dm_put() to hold md for each I/O
until its request completion handling is fully done.
However, the final dm_put() can call the device deletion code which
must not be run in interrupt context and may cause kernel panic.
To solve the problem, this patch moves the device deletion code,
dm_destroy(), to predetermined places that is actually deleting
the mapped_device in ioctl (process) context, and changes dm_put()
just to decrement the reference count of the mapped_device.
By this change, dm_put() can be used in any context and the symmetric
model below is introduced:
dm_create(): create a mapped_device
dm_destroy(): destroy a mapped_device
dm_get(): increment the reference count of a mapped_device
dm_put(): decrement the reference count of a mapped_device
dm_destroy() waits for all references of the mapped_device to disappear,
then deletes the mapped_device.
dm_destroy() uses active waiting with msleep(1), since deleting
the mapped_device isn't performance-critical task.
And since at this point, nobody opens the mapped_device and no new
reference will be taken, the pending counts are just for racing
completing activity and will eventually decrease to zero.
For the unlikely case of the forced module unload, dm_destroy_immediate(),
which doesn't wait and forcibly deletes the mapped_device, is also
introduced and used in dm_hash_remove_all(). Otherwise, "rmmod -f"
may be stuck and never return.
And now, because the mapped_device is deleted at this point, subsequent
accesses to the mapped_device may cause NULL pointer references.
Cc: stable@kernel.org
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes dm_hash_remove_all() to release _hash_lock when
removing a device. After removing the device, dm_hash_remove_all()
takes _hash_lock and searches the hash from scratch again.
This patch is a preparation for the next patch, which changes device
deletion code to wait for md reference to be 0. Without this patch,
the wait in the next patch may cause AB-BA deadlock:
CPU0 CPU1
-----------------------------------------------------------------------
dm_hash_remove_all()
down_write(_hash_lock)
table_status()
md = find_device()
dm_get(md)
<increment md->holders>
dm_get_live_or_inactive_table()
dm_get_inactive_table()
down_write(_hash_lock)
<in the md deletion code>
<wait for md->holders to be 0>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch prevents access to mapped_device which is being deleted.
Currently, even after a mapped_device has been removed from the hash,
it could be accessed through idr_find() using minor number.
That could cause a race and NULL pointer reference below:
CPU0 CPU1
------------------------------------------------------------------
dev_remove(param)
down_write(_hash_lock)
dm_lock_for_deletion(md)
spin_lock(_minor_lock)
set_bit(DMF_DELETING)
spin_unlock(_minor_lock)
__hash_remove(hc)
up_write(_hash_lock)
dev_status(param)
md = find_device(param)
down_read(_hash_lock)
__find_device_hash_cell(param)
dm_get_md(param->dev)
md = dm_find_md(dev)
spin_lock(_minor_lock)
md = idr_find(MINOR(dev))
spin_unlock(_minor_lock)
dm_put(md)
free_dev(md)
dm_get(md)
up_read(_hash_lock)
__dev_status(md, param)
dm_put(md)
This patch fixes such problems.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
All the dm ioctls that generate uevents set the DM_UEVENT_GENERATED flag so
that userspace knows whether or not to wait for a uevent to be processed
before continuing,
The dm rename ioctl sets this flag but was not structured to return it
to userspace. This patch restructures the rename ioctl processing to
behave like the other ioctls that return data and so fix this.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove useless __dev_status call while processing an ioctl that sets up
device geometry and target message. The data is not returned to
userspace so there is no point collecting it and in the case of
target_message it is collected before processing the message so if it
did return it might be stale.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Validate chunk size against both origin and snapshot sector size
Don't allow chunk size smaller than either origin or snapshot logical
sector size. Reading or writing data not aligned to sector size is not
allowed and causes immediate errors.
This requires us to open the origin before initialising the
exception store and to export dm_snap_origin.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Iterate both origin and snapshot devices
iterate_devices method should call the callback for all the devices where
the bio may be remapped. Thus, snapshot_iterate_devices should call the callback
for both snapshot and origin underlying devices because it remaps some bios
to the snapshot and some to the origin.
snapshot_iterate_devices called the callback only for the origin device.
This led to badly calculated device limits if snapshot and origin were placed
on different types of disks.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
multipath_ctr() forgets to return an error after detecting
missing path parameters. Fix this.
Signed-off-by: Patrick LoPresti <lopresti@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When we find no ROM we understand and a device-tree is present, see
if we can retreive clock info from there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This never really got fixed in mesa, and the kernel deals with the problem
just fine, so don't got reporting things that confuse people.
Signed-off-by: Dave Airlie <airlied@redhat.com>
0 is a valid DMA address from pci_map_page(), use pci_dma_mapping_error()
instead to check for errors
[airlied: fix warning + two other places with errors.]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a CS checker fix. I need this for FP16 alpha-test.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
add default case for buffer formats
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Andre Maasikas <amaasikas@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently most, if not all, memory allocation in drm_bufs.c is followed by initializing the memory with 0.
Replace the use of kmalloc+memset with kzalloc.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prevent build errors when SCSI is not enabled:
iscsi_ibft.c:(.init.text+0x548d): undefined reference to `iscsi_boot_create_initiator'
iscsi_ibft.c:(.init.text+0x54a9): undefined reference to `iscsi_boot_create_ethernet'
iscsi_ibft.c:(.init.text+0x54c5): undefined reference to `iscsi_boot_create_target'
iscsi_ibft.c:(.init.text+0x55ff): undefined reference to `iscsi_boot_destroy_kset'
iscsi_ibft.c:(.init.text+0x561e): undefined reference to `iscsi_boot_create_kset'
iscsi_ibft.c:(.exit.text+0xe2c): undefined reference to `iscsi_boot_destroy_kset'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
We failed to check to see if actually allocated structures
to contain the iBFT structure and went ahead to dereference it.
This patch fixes the OOPS.
Reported-by: "Jayamohan Kalickal" <jayamohank@serverengines.com>
Tested-by: "Jayamohan Kalickal" <jayamohank@serverengines.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>
Add multiplexed bus core support. I2C multiplexer and switches
like pca954x get instantiated as new adapters per port.
Signed-off-by: Michael Lawnick <ml.lawnick@gmx.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Moving userspace-instantiated clients to separate lists wasn't nearly
enough to avoid deadlocks in multiplexed bus cases. We also want to
have a dedicated mutex to protect each list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Make i2c_default_probe self-sufficient, so that callers don't have to
do functionality checks themselves. This ensures everything is and
will stay consistent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that bus_for_each_drv() is no longer __must_check, we can drop the
dummy variable that was used to store the returned value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Uninline i2c adapter locking helper functions, move them to i2c-core,
and use them in i2c-core itself. The functions are still exported for
external users. This makes future updates to the locking model (which
will be needed for multiplexing support) possible and transparent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Now that i2c-core offers the possibility to provide custom probing
function for I2C devices, let's make use of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use memdup_user when user data is immediately copied into the allocated
region. Note that in the second case, the ++i is no longer necessary, as
the last value is already freed if needed by the call to memdup_user.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
