Group floors into a common cascade structure. This will provide a common
structure to store common data to all cascaded docg3 chips, like IO
addressing, locking protection.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After several tries with ubifs, it appears empirically that constructor
provided figures for erase/write timeouts are underestimated. A timeout
of 100ms seems to work with a 5 years worn chip, and no timeouts occur
anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The last erase block was not accessible, as the out of bound
check was incorrectly rejecting the last block.
The read/write/erase offset checks were forbidding the usage of the
last block, because of the calculation which was considering the
byte after the last instead of the last byte.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
phram_setup() is only called from init_phram() which is in .init.text,
so it must be in the same section to avoid a section mismatch warning.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support to configure the SPEAr SMI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Additionally, after failing in mtd_device_parse_register(), the driver
unmap/free code is now executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
doc_probe_device() is only called from docg3_probe() which is in .init.text,
so it must be in the same section to avoid a section mismatch warning.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is based on Ville Herva's similar patch to block2mtd.
Trying to pass a parameter through the kernel command line when built-in would
crash the kernel, as phram_setup() was called so early that kmalloc() was not
functional yet.
This patch only saves the parameter string at the early boot stage, and parses
it later when init_phram() is called. The same happens in both module and
built-in cases.
With this patch, I can boot with a statically-compiled phram, and mount a
ext2 root fs from physical RAM, without the need for a initrd.
This has been tested in built-in and module cases, with and without a
parameter string.
Artem: amended comments a bit
Signed-off-by: Hervé Fache <h-fache@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.
Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.
Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE. It is set in the
driver for all other modes.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The read function was so far requiring the reads to be aligned on page
boundaries, and be page length multiples in size. Relieve these
constraints to ease the userspace ubifs programs runs, which read ubifs
headers of 64 bytes.
Artem: squashed a later fix from Robert Jarzmik into this patch.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The first 3 arguments of 'mtd_device_parse_register()' are pointers,
but many callers pass '0' instead of 'NULL'. Fix this globally. Thanks
to coccinelle for making it easy to do with the following semantic patch:
@@
expression mtd, types, parser_data, parts, nr_parts;
@@
(
-mtd_device_parse_register(mtd, 0, parser_data, parts, nr_parts)
+mtd_device_parse_register(mtd, NULL, parser_data, parts, nr_parts)
|
-mtd_device_parse_register(mtd, types, 0, parts, nr_parts)
+mtd_device_parse_register(mtd, types, NULL, parts, nr_parts)
|
-mtd_device_parse_register(mtd, types, parser_data, 0, nr_parts)
+mtd_device_parse_register(mtd, types, parser_data, NULL, nr_parts)
)
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Change the name of the mtd so that it is simpler, and is easier to
cope with by mtdparts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In many places in drivers we verify for the zero length, but this is very
inconsistent across drivers. This is obviously the right thing to do, though.
This patch moves the check to the MTD API functions instead and removes a lot
of duplication.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some MTD drivers return -EINVAL if the 'phys' parameter is not NULL, trying to
convey that they cannot return the physical address. However, this is not very
logical because they still can return the virtual address ('virt'). But some
drivers (lpddr) just ignore the 'phys' parameter instead, which is a more
logical thing to do.
Let's harmonize this and:
1. Always initialize 'virt' and 'phys' to 'NULL' in 'mtd_point()'.
2. Do not return an error if the physical address cannot be found.
So as a result, all drivers will set 'phys' to 'NULL' if it is not supported.
None of the 'mtd_point()' users use 'phys' anyway, so this should not break
anything. I guess we could also just delete this parameter later.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This header is tiny and contains only pmc551-private stuff, so it should
not live in 'include/linux' - let's just merge it with pmc551.c.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MTD API function now zero the 'retlen' parameter before calling
the driver's method — do not do this again in drivers. This removes
duplicated '*retlen = 0' assignent from the following methods:
'mtd_point()'
'mtd_read()'
'mtd_write()'
'mtd_writev()'
'mtd_panic_write()'
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.
And again a bit of noise - deleted few too sparse newlines, sorry.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We already verify that offset and length are within the MTD device size
in the MTD API functions. Let's remove the duplicated checks in drivers.
This patch only affects the following API's:
'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'
This patch adds a bit of noise by removing too sparse empty lines, but this is
not too bad.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.
Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to 4 because this drivers writes at max 4 bytes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
However, we forgot to set this parameter for block2mtd. Set it to PAGE_SIZE
because this is actually the amount of data we write at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Joern Engel <joern@lazybastard.org>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using UBI on m25p80 can give messages like:
UBI error: io_init: bad write buffer size 0 for 1 min. I/O unit
We need to initialize writebufsize; I think "page_size" is the correct
"bufsize", although I'm not sure. Comments?
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the drivers in drivers/mtd/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Driver must cleanup all held resources during remove. It wasn't
releasing requested memory region.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since "length" is a u32, the error handling below didn't work when
fixup_pmc551() returns -ENODEV.
if ((length = fixup_pmc551(PCI_Device)) <= 0)
This patch changes both the type of "length" and the return type of
fixup_pmc551() to int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
CONFIG_GENERIC_IO is just enough for the basic MTD stuff.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk8Mq/MACgkQdwG7hYl686PeFACfZCgbdDWD9A/JL+i1RMfExVu6
Pi0An3Hmc3PTCp0yQ21KtcKhpF9CAMEu
=NfuL
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6
MTD pull for 3.3
* tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6: (113 commits)
mtd: Fix dependency for MTD_DOC200x
mtd: do not use mtd->block_markbad directly
logfs: do not use 'mtd->block_isbad' directly
mtd: introduce mtd_can_have_bb helper
mtd: do not use mtd->suspend and mtd->resume directly
mtd: do not use mtd->lock, unlock and is_locked directly
mtd: do not use mtd->sync directly
mtd: harmonize mtd_writev usage
mtd: do not use mtd->lock_user_prot_reg directly
mtd: mtd->write_user_prot_reg directly
mtd: do not use mtd->read_*_prot_reg directly
mtd: do not use mtd->get_*_prot_info directly
mtd: do not use mtd->read_oob directly
mtd: mtdoops: do not use mtd->panic_write directly
romfs: do not use mtd->get_unmapped_area directly
mtd: do not use mtd->get_unmapped_area directly
mtd: do use mtd->point directly
mtd: introduce mtd_has_oob helper
mtd: mtdcore: export symbols cleanup
mtd: clean-up the default_mtd_writev function
...
Fix up trivial edit/remove conflict in drivers/staging/spectra/lld_mtd.c
This patch makes the 'mtd_writev()' function more usable and logical. We first
teach it to fall-back to the 'default_mtd_writev()' function if the MTD driver
does not define its own '->writev()' method. Then we make block2mtd and JFFS2
just 'mtd_writev()' instead of 'default_mtd_writev()' function. This means we
can now stop exporting 'default_mtd_writev()' and instead, export
'mtd_writev()'. This is much cleaner and more logical, as well as allows us to
get read of another direct 'mtd->writev' access in JFFS2.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the following gcc warning:
drivers/mtd/devices/sst25l.c: In function ‘sst25l_probe’:
drivers/mtd/devices/sst25l.c:381:11: warning: unused variable ‘i’ [-Wunused-variable]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'struct mtd_info' object is allocated with 'kzalloc()', so it
contains only zeroes - no need to initialize various fields to 0 or
NULL.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of calling 'kmalloc()' and them 'memeset(0)', use 'kzalloc()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As the MTD api has no use for the number of erase cycles
each block has endured, remove the function which calculated
that value.
If one day MTD api finds it usefull for wear levelling
algorithms to have this information, the function should be
put back in place.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch takes into account checkpatch, sparse and ECC
comments.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If doc_probe_device() returned an ERR_PTR, then we accidentally saved
that to docg3_floors[floor] = mtd; which gets derefenced in the error
handling when we call doc_release_device().
I've reworked the error handling to take care of that and hopefully
make it a little simpler.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As each docg3 chip has 2 protection areas (DPS0 and DPS1),
and because theses areas can prevent user access to the chip
data, add for each floor the sysfs entries which insert the
protection key into the right DPS.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Docg3 chips can work in 3 modes : normal MLC mode, fast
mode and reliable mode. Normally, as docg3 is a MLC chip, it
should be configured to work in normal mode.
In both normal mode, each page is distinct. This
means that writing to page 12 of blocks 14,15 writes only to
that page, and reading from page 12 of blocks 14,15 reads
only from that page.
In reliable and fast modes, pages are coupled by pairs, and
are clones one of each other. This means that the available
capacity of the chip is halved. Pages are coupled in each
block, and page of index 2*n contains the same data as page
2*n+1 of the same block.
In fast mode, the reads occur a bit faster, but are a bit
less reliable that in normal mode.
When reading from page 2*n, the chip reads bytes from both
page 2*n and page 2*n+1, makes a logical and for each byte,
and returns the result. As programming a page means
"clearing bits", even if a bit was not cleared on one page
because the flash is worn out, the other page has the bit
cleared, and the result of the "AND" gives a correct result.
When writing to page 2*n, the chip writes data to both page
2*n and page 2*n+1.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add functions to powerdown and powerup from suspend, in
order to save power.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Credit for discovering the BCH algorith parameters, and bit
reversing algorithm is to be give to Mike Dunn and Ivan
Djelic.
The BCH correction code relied upon the BCH library, where
all data and ECC is bit-reversed. The BCH library works
correctly when each input byte is bit-reversed, and
accordingly ECC output is also bit-reversed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Map the developped write and erase functions into the mtd
structure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add erase capability to the docg3 driver. The erase block is
made of 2 physical blocks, as both share all 64 pages. That
makes an erase block of at least 64 kBytes.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add write capability to the docg3 driver. The writes are
possible on a single page (512 bytes + 16 bytes), even if
that page is split on 2 physical pages on 2 blocks (each on
one plane).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add OOB buffer area to store the OOB data until the actual
page is written, so that it can be completed by hardware ECC
generator.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the required registers and commands to erase and write
flash pages / blocks.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add OOB layout description for docg3, so that userspace can
use this information to setup the data for write_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for multiple floors, ie. cascaded docg3
chips. There might be 4 docg3 chips cascaded, sharing the
same address space, and providing up to 4 times the storage
capacity of a unique chip.
Each floor will be seen as an independant mtd device.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the docg3 reads to be able to cope with all possible
data buffer / oob buffer / file mode combinations from
docg3_read_oob().
This especially ensures that raw reads do not use ECC
corrections, and AUTOOOB and PLACEOOB do use ECC
correction.
The approach is to empty docg3_read() and make it a wrapper
to docg3_read_oob(). As docg3_read_oob() handles all the
funny cases (no data buffer but oob buffer, data buffer but
no oob buffer, ...), docg3_read() is just a special use of
docg3_read_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
BCH registers are contiguous, not on every byte. Fix the
register definitions.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The protection areas boundaries were on 16bit registers, not
8bit. This is consistent with block numbers, which can
extend up to 4096 on bigger chips (and is 2048 on the
docg3).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Writeb was incorrectly traced as a 16 bits write, instead of
a 8 bits write. Fix it by tracing the correct width.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Change the NOP debug log verbosity to very verbose to
unburden log analysis.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move invalidate_bdev, block_sync_page into fs/block_dev.c. Export
kill_bdev as well, so brd doesn't have to open code it. Reduce
buffer_head.h requirement accordingly.
Removed a rather large comment from invalidate_bdev, as it looked a bit
obsolete to bother moving. The small comment replacing it says enough.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Depending on whether MTD_DOCPROBE_ADVANCED is set or not,
MTD_DOCPROBE_ADDRESS will default to either 0x0000 or 0. That should
lead to (basically) identical code in docprobe.c. The current two
defaults should be merged.
And, while we're at it, if MTD_DOCPROBE is set MTD_DOCPROBE_ADDRESS will
always be set. (MTD_DOCPROBE_ADDRESS depends on MTD_DOCPROBE and it has
a default value.) So the check whether CONFIG_MTD_DOCPROBE_ADDRESS is
defined is unnecessary and should be dropped.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
On some platforms such as P3060QDS, has multiple spi flashes, but they are
not available at same time, so if their status is 'disabled', which is set
by u-boot, will not be probed.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add support for DiskOnChip G3 chips. The support is quite
limited yet :
- no flash writes/erases are implemented
- ECC fixes are not implemented
- powerdown is not implemented
- IPL handling is not yet done
On the brighter side, the chip reading does work.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add support for EON spi flash EN25Q32B, which is not listed in id table,
need to add it in the id table to support the EON flash.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
These modes are not necessarily for OOB only. Particularly, MTD_OOB_RAW
affected operations on in-band page data as well. To clarify these
options and to emphasize that their effect is applied per-operation, we
change the primary prefix to MTD_OPS_.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic
debugging feature is a generic kernel feature that provides more
flexibility.
(See Documentation/dynamic-debug-howto.txt)
Also fix some punctuation, indentation, and capitalization that went
along with the affected lines.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
It adds device tree probe support for mtd_dataflash driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Consolidate knowledge about partitions in drivers/mtd/devices/lart.c.
Drop all HAVE_PARTITIONS conditionals. Always use partitioning.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I no longer work at Bluewater Systems. Update my email address accordingly. I
have deleted my email address from C files rather than change it. This
was suggested by several people, since the commit from my new email
address will cause scripts/get_maintainer.pl to function properly. I
have not added the .mailmap entry as suggested by Joe because I think
it is no longer necessary if I touch all the files which had my name
in them.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Andre Renaud <andre@bluewatersys.com>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: trivial@kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The older add_mtd_device()/add_mtd_partitions() and their removal
counterparts will soon be gone. Replace uses with mtd_device_register()
and mtd_device_unregister().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the check for
mtd_has_partitions() as we always have partitioning enabled now.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The previous section mismatch fix for this driver wasn't entirely correct.
The sst25l_flash_info array is now used in the devinit probe func, but is
marked as initdata, so building results in the warning:
WARNING: drivers/mtd/devices/sst25l.o(.devinit.text): Section mismatch
in reference from the function sst25l_probe()
to the variable .init.data:sst25l_flash_info
Further, the remove func should be devexit rather than exit to match the
probe func.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
S25FL512S = 64MiB single die, same family as S25FL256S
S70FL01GS = 2x S25FL512S dies in one package (separate chip selects)
These devices are not sampling yet, but they are expected to be very
similar to S25FL256S, which has been tested.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
These are 32MiB parts which use a slightly different 4-byte enable
sequence from Macronix.
Default to the Spansion 4-byte scheme in set_4byte(), as it is more
likely to be copied by other vendors.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the manufacturer ID names from cfi.h instead of hard-coding
hex constants. Introduce a JEDEC_MFR macro for clarity.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 4f678a58 (mtd: fix memory leaks in phram_setup) missed two cases
where the memory allocated for name would be leaked. This commit frees
the memory when register_device() fails and on unregister_devices().
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Set the 'mtd->writebufsize' field to 64 to mimic modern CFI flashes.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
The last byte of the ID should be zero for this chip. Was added in
commit d0e8c47c58 . Reported by Tomi
Varjo.
Signed-off-by: Aleksandr Koltsoff <aleksandr.koltsoff@ebts.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a DEBUG(MTD_DEBUG_LEVEL2, ..) trace at beginning of sst_write() function as
it is done in m25p80_write() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Building the kernel with 'make CONFIG_DEBUG_SECTION_MISMATCH=y´
resulted in:
WARNING: vmlinux.o(.data+0x15938): Section mismatch in reference from
the variable sst25l_driver to the function .init.text:sst25l_probe()
The variable sst25l_driver references
the function __init sst25l_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Fix the section mismatch.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Untested, but expected to be compatible with MX25L25635E which I did
test.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>