Commit Graph

78 Commits

Author SHA1 Message Date
Allen Kay
ae21ee65e8 PCI: acs p2p upsteram forwarding enabling
Note: dom0 checking in v4 has been separated out into 2/2.

This patch enables P2P upstream forwarding in ACS capable PCIe switches.
It solves two potential problems in virtualization environment where a PCIe
device is assigned to a guest domain using a HW iommu such as VT-d:

1) Unintentional failure caused by guest physical address programmed
   into the device's DMA that happens to match the memory address range
   of other downstream ports in the same PCIe switch.  This causes the PCI
   transaction to go to the matching downstream port instead of go to the
   root complex to get translated by VT-d as it should be.

2) Malicious guest software intentionally attacks another downstream
   PCIe device by programming the DMA address into the assigned device
   that matches memory address range of the downstream PCIe port.

We are in process of implementing device filtering software in KVM/XEN
management software to allow device assignment of PCIe devices behind a PCIe
switch only if it has ACS capability and with the P2P upstream forwarding bits
enabled.  This patch is intended to work for both KVM and Xen environments.

Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Reviewed-by: Mathew Wilcox <willy@linux.intel.com>
Reviewed-by: Chris Wright <chris@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 08:47:25 -08:00
Eric W. Biederman
0ba379ec0f PCI: Simplify hotplug mch quirk.
There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.

Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.

The re-running of this fixup after pci hotplug happens below these
devices is totally bogus.  All of the state we change is pure software
state and we don't change the hardware at all.  Which means hotplug on
the lower devices doesn't have a chance to change this state.  So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.

I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.

Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-09-09 14:06:49 -07:00
Michael S. Tsirkin
711d57796f PCI: expose function reset capability in sysfs
Some devices allow an individual function to be reset without affecting
other functions in the same device: that's what pci_reset_function does.
For devices that have this support, expose reset attribite in sysfs.

This is useful e.g. for virtualization, where a qemu userspace
process wants to reset the device when the guest is reset,
to emulate machine reboot as closely as possible.

Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-09-09 13:29:24 -07:00
Chris Wright
6faf17f6f1 PCI SR-IOV: correct broken resource alignment calculations
An SR-IOV capable device includes an SR-IOV PCIe capability which
describes the Virtual Function (VF) BAR requirements.  A typical SR-IOV
device can support multiple VFs whose BARs must be in a contiguous region,
effectively an array of VF BARs.  The BAR reports the size requirement
for a single VF.  We calculate the full range needed by simply multiplying
the VF BAR size with the number of possible VFs and create a resource
spanning the full range.

This all seems sane enough except it artificially inflates the alignment
requirement for the VF BAR.  The VF BAR need only be aligned to the size
of a single BAR not the contiguous range of VF BARs.  This can cause us
to fail to allocate resources for the BAR despite the fact that we
actually have enough space.

This patch adds a thin PCI specific layer over the generic
resource_alignment() function which is aware of the special nature of
VF BARs and does sorting and allocation based on the smaller alignment
requirement.

I recognize that while resource_alignment is generic, it's basically a
PCI helper.  An alternative to this patch is to add PCI VF BAR specific
information to struct resource.  I opted for the extra layer rather than
adding such PCI specific information to struct resource.  This does
have the slight downside that we don't cache the BAR size and re-read
for each alignment query (happens a small handful of times during boot
for each VF BAR).

Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-08-30 08:37:25 -07:00
Yu Zhao
e277d2fc79 PCI: handle Virtual Function ATS enabling
The SR-IOV spec requires that the Smallest Translation Unit and
the Invalidate Queue Depth fields in the Virtual Function ATS
capability are hardwired to 0. If a function is a Virtual Function,
then and set its Physical Function's STU before enabling the ATS.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-05-18 11:25:58 +01:00
Yu Zhao
302b4215da PCI: support the ATS capability
The PCIe ATS capability makes the Endpoint be able to request the
DMA address translation from the IOMMU and cache the translation
in the device side, thus alleviate IOMMU pressure and improve the
hardware performance in the I/O virtualization environment.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-05-18 11:25:54 +01:00
Linus Torvalds
e76e5b2c66 Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
  PCI: fix HT MSI mapping fix
  PCI: don't enable too much HT MSI mapping
  x86/PCI: make pci=lastbus=255 work when acpi is on
  PCI: save and restore PCIe 2.0 registers
  PCI: update fakephp for bus_id removal
  PCI: fix kernel oops on bridge removal
  PCI: fix conflict between SR-IOV and config space sizing
  powerpc/PCI: include pci.h in powerpc MSI implementation
  PCI Hotplug: schedule fakephp for feature removal
  PCI Hotplug: rename legacy_fakephp to fakephp
  PCI Hotplug: restore fakephp interface with complete reimplementation
  PCI: Introduce /sys/bus/pci/devices/.../rescan
  PCI: Introduce /sys/bus/pci/devices/.../remove
  PCI: Introduce /sys/bus/pci/rescan
  PCI: Introduce pci_rescan_bus()
  PCI: do not enable bridges more than once
  PCI: do not initialize bridges more than once
  PCI: always scan child buses
  PCI: pci_scan_slot() returns newly found devices
  PCI: don't scan existing devices
  ...

Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
2009-04-01 09:47:12 -07:00
Rafael J. Wysocki
0128a89cf7 PCI PM: Move pci_restore_standard_config to pci-driver.c
Move pci_restore_standard_config() from pci.c to pci-driver.c and
make it static.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-30 21:46:55 +02:00
Alex Chiang
705b1aaa82 PCI: Introduce /sys/bus/pci/rescan
This interface allows the user to force a rescan of all PCI buses
in system, and rediscover devices that have been removed earlier.

pci_bus_attrs implementation from Trent Piepho.

Thanks to Vegard Nossum for discovering locking issues with the
sysfs interface.

Cc: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 14:57:58 -07:00
Yu Zhao
74bb1bcc7d PCI: handle SR-IOV Virtual Function Migration
Add or remove a Virtual Function after receiving a Migrate In or Out
Request.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:28 -07:00
Yu Zhao
dd7cc44d0b PCI: add SR-IOV API for Physical Function driver
Add or remove the Virtual Function when the SR-IOV is enabled or
disabled by the device driver. This can happen anytime rather than
only at the device probe stage.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:26 -07:00
Yu Zhao
480b93b783 PCI: centralize device setup code
Move the device setup stuff into pci_setup_device() which will be used
to setup the Virtual Function later.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:25 -07:00
Yu Zhao
a28724b0fb PCI: reserve bus range for SR-IOV device
Reserve the bus number range used by the Virtual Function when
pcibios_assign_all_busses() returns true.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:24 -07:00
Yu Zhao
8c5cdb6adc PCI: restore saved SR-IOV state
Restore the volatile registers in the SR-IOV capability after the
D3->D0 transition.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:24 -07:00
Yu Zhao
d1b054da8f PCI: initialize and release SR-IOV capability
If a device has the SR-IOV capability, initialize it (set the ARI
Capable Hierarchy in the lowest numbered PF if necessary; calculate
the System Page Size for the VF MMIO, probe the VF Offset, Stride
and BARs). A lock for the VF bus allocation is also initialized if
a PF is the lowest numbered PF.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:22 -07:00
Yuji Shimada
32a9a682be PCI: allow assignment of memory resources with a specified alignment
This patch allows memory resources to be assigned with a specified
alignment at boot-time or run-time. The patch is useful when we use PCI
pass-through, because page-aligned memory resources are required to
securely share PCI resources with guest drivers.

If you want to assign the resource at boot time, please set
"pci=resource_alignment=" boot parameter.

This is format of "pci=resource_alignment=" boot parameter:

        [<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
                Specifies alignment and device to reassign
                aligned memory resources.
                If <order of align> is not specified, PAGE_SIZE is
                used as alignment.
                PCI-PCI bridge can be specified, if resource
                windows need to be expanded.

This is example:

        pci=resource_alignment=20@07:00.0;18@0f:00.0;00:1d.7

If you want to assign the resource at run-time, please set
"/sys/bus/pci/resource_alignment" file, and hot-remove the device and
hot-add the device.  For this purpose, fakephp or PCI hotplug interfaces
can be used.

The format of "/sys/bus/pci/resource_alignment" file is the same with
boot parameter. You can use "," instead of ";".

For example:

        # cd /sys/bus/pci
        # echo -n 20@12:00.0 > resource_alignment
        # echo 1 > devices/0000:12:00.0/remove
        # echo 1 > rescan

Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:15 -07:00
Randy Dunlap
b33bfdef24 PCI: fix struct pci_platform_pm_ops kernel-doc
Fix struct pci_platform_pm_ops kernel-doc notation.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-02-13 12:02:47 -08:00
Rafael J. Wysocki
aa8c6c9374 PCI PM: Restore standard config registers of all devices early
There is a problem in our handling of suspend-resume of PCI devices that
many of them have their standard config registers restored with
interrupts enabled and they are put into the full power state with
interrupts enabled as well.  This may lead to the following scenario:
  * an interrupt vector is shared between two or more devices
  * one device is resumed earlier and generates an interrupt
  * the interrupt handler of another device tries to handle it and
    attempts to access the device the config space of which hasn't been
    restored yet and/or which still is in a low power state
  * the system crashes as a result

To prevent this from happening we should restore the standard
configuration registers of all devices with interrupts disabled and we
should put them into the D0 power state right after that.
Unfortunately, this cannot be done using the existing
pci_set_power_state(), because it can sleep.  Also, to do it we have to
make sure that the config spaces of all devices were actually saved
during suspend.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-16 12:57:58 -08:00
Rafael J. Wysocki
734104292f PCI PM: Avoid touching devices behind bridges in unknown state
It generally is better to avoid accessing devices behind bridges that
may not be in the D0 power state, because in that case the bridges'
secondary buses may not be accessible.  For this reason, during the
early phase of resume (ie. with interrupts disabled), before
restoring the standard config registers of a device, check the power
state of the bridge the device is behind and postpone the restoration
of the device's config space, as well as any other operations that
would involve accessing the device, if that state is not D0.

In such cases the restoration of the device's config space will be
retried during the "normal" phase of resume (ie. with interrupts
enabled), so that the bridge can be put into D0 before that happens.

Also, save standard configuration registers of PCI devices during the
"normal" phase of suspend (ie. with interrupts enabled), so that the
bridges the devices are behind can be put into low power states (we
don't put bridges into low power states at the moment, but we may
want to do it in the future and it seems reasonable to design for
that).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:16:05 -08:00
Rafael J. Wysocki
fa58d305d9 PCI PM: Add suspend counterpart of pci_reenable_device
PCI devices without drivers are not disabled during suspend and
hibernation, but they are enabled during resume, with the help of
pci_reenable_device(), so there is an unbalanced execution of
pcibios_enable_device() in the resume code path.

To correct this introduce function pci_disable_enabled_device()
that will disable the argument device, if it is enabled when the
function is being run, without updating the device's pci_dev
structure and use it in the suspend code path to balance the
pci_reenable_device() executed during resume.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:14:40 -08:00
Stephen Hemminger
287d19ce2e PCI: revise VPD access interface
Change PCI VPD API which was only used by sysfs to something usable
in drivers.
   * move iteration over multiple words to the low level
   * use conventional types for arguments
   * add exportable wrapper

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:17 -08:00
Jesse Barnes
eb9c39d031 PCI: set device wakeup capable flag if platform support is present
When PCI devices are initialized, we check whether they support PCI PM
caps and set the device can_wakeup flag if so.  However, some devices
may have platform provided wakeup events rather than PCI PME signals, so
we need to set can_wakeup in that case too.  Doing so should allow
wakeups from many more devices, especially on cost constrained systems.

Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Joseph Chan <JosephChan@via.com.tw>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:07 -08:00
Yu Zhao
876e501ab2 PCI: factor pci_bus_add_child() from pci_bus_add_devices()
This patch splits a new function, pci_bus_add_child(), from
pci_bus_add_devices(). The new function can be used to register PCI
buses to the device core.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:06 -08:00
Yu Zhao
613e7ed6f7 PCI: add a new function to map BAR offsets
Add a function to map a given resource number to a corresponding
register so drivers can get the offset and type of device specific BARs.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:04 -08:00
Yu Zhao
0b400c7ed4 PCI: export __pci_read_base()
Export __pci_read_base() so it can be used by whole PCI subsystem.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:02 -08:00
Yu Zhao
6a49d81200 PCI: enhance pci_ari_enabled()
Change parameter of pci_ari_enabled() from 'pci_dev' to 'pci_bus'.

ARI forwarding on the bridge mostly concerns the subordinate devices
rather than the bridge itself. So this change will make the function
easier to use.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:12:59 -08:00
Rafael J. Wysocki
63f4898ace PCI: handle PCI state saving with interrupts disabled
Since interrupts will soon be disabled at PCI resume time, we need to
pre-allocate memory to save/restore PCI config space (or use GFP_ATOMIC,
but this is safer).

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:12:40 -08:00
Andrew Patterson
07ae95f988 ACPI/PCI: PCI MSI _OSC support capabilities called when root bridge added
The _OSC capability OSC_MSI_SUPPORT is set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the PCI
MSI driver.  Also adds the function pci_msi_enabled, which returns true
if pci=nomsi is not on the kernel command-line.

Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:12:31 -08:00
Jesse Barnes
9eff02e204 PCI: check mmap range of /proc/bus/pci files too
/proc/bus/pci allows you to mmap resource ranges too, so we should probably be
checking to make sure the mapping is somewhat valid.  Uses the same code as the recent sysfs mmap range checking patch from Linus.

Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:12:20 -08:00
Taku Izumi
d389fec6a2 ACPI/PCI: Set support bit for MSI in support field of _OSC
Currently linux doesn't have any code to set the "MSI supported" bit in
Support Fireld of _OSC. This patch adds the code for that.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-22 16:42:35 -07:00
Benjamin Herrenschmidt
f19aeb1f36 PCI: Add ability to mmap legacy_io on some platforms
This adds the ability to mmap legacy IO space to the legacy_io files
in sysfs on platforms that support it. This will allow to clean up
X to use this instead of /dev/mem for legacy IO accesses such as
those performed by Int10.

While at it I moved pci_create/remove_legacy_files() to pci-sysfs.c
where I think they belong, thus making more things statis in there
and cleaned up some spurrious prototypes in the ia64 pci.h file

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 11:01:46 -07:00
Yu Zhao
58c3a727cb PCI: support PCIe ARI capability
This patch adds support for PCI Express Alternative Routing-ID
Interpretation (ARI) capability.

The ARI capability extends the Function Number field of the PCI Express
Endpoint by reusing the Device Number which is otherwise hardwired to 0.
With ARI, an Endpoint can have up to 256 functions.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:54:32 -07:00
Zhao, Yu
557848c3c0 PCI: replace cfg space size (256/4096) by macros.
This is a cleanup that changes all PCI configuration space size
representations to the macros (PCI_CFG_SPACE_SIZE and
PCI_CFG_SPACE_EXP_SIZE). And the macros are also moved from
drivers/pci/probe.c to drivers/pci/pci.h.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:54:29 -07:00
Mike Travis
93ff68a55a PCI: make CPU list affinity visible
Stephen Hemminger wrote:
> Looks like Mike created cpulistaffinty in sysfs but never completed
> the job.

This patch hooks things up correctly, taking care to remove the new file
when the bus is destroyed.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:53:51 -07:00
Linus Torvalds
dc7c65db28 Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
  Revert "x86/PCI: ACPI based PCI gap calculation"
  PCI: remove unnecessary volatile in PCIe hotplug struct controller
  x86/PCI: ACPI based PCI gap calculation
  PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
  PCI PM: Fix pci_prepare_to_sleep
  x86/PCI: Fix PCI config space for domains > 0
  Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
  PCI: Simplify PCI device PM code
  PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
  PCI ACPI: Rework PCI handling of wake-up
  ACPI: Introduce new device wakeup flag 'prepared'
  ACPI: Introduce acpi_device_sleep_wake function
  PCI: rework pci_set_power_state function to call platform first
  PCI: Introduce platform_pci_power_manageable function
  ACPI: Introduce acpi_bus_power_manageable function
  PCI: make pci_name use dev_name
  PCI: handle pci_name() being const
  PCI: add stub for pci_set_consistent_dma_mask()
  PCI: remove unused arch pcibios_update_resource() functions
  PCI: fix pci_setup_device()'s sprinting into a const buffer
  ...

Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
2008-07-16 17:25:46 -07:00
Rafael J. Wysocki
a80a6da145 PCI ACPI: Drop the second argument of platform_pci_choose_state
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-07-16 23:27:02 +02:00
Rafael J. Wysocki
eb9d0fe40e PCI ACPI: Rework PCI handling of wake-up
* Introduce function acpi_pm_device_sleep_wake() for enabling and
  disabling the system wake-up capability of devices that are power
  manageable by ACPI.

* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
  subsystems to check if ACPI is able to enable the system wake-up
  capability of given device.

* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
  for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().

* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
  for the ACPI 'driver' make it use acpi_bus_can_wakeup().

* Move the PME# handlig code out of pci_enable_wake() and split it
  into two functions, pci_pme_capable() and pci_pme_active(),
  allowing the caller to check if given device is capable of
  generating PME# from given power state and to enable/disable the
  device's PME# functionality, respectively.

* Modify pci_enable_wake() to use the new ACPI callbacks and the new
  PME#-related functions.

* Drop the generic .platform_enable_wakeup() callback that is not
  used any more.

* Introduce device_set_wakeup_capable() that will set the
  power.can_wakeup flag of given device.

* Rework PCI device PM initialization so that, if given device is
  capable of generating wake-up events, either natively through the
  PME# mechanism, or with the help of the platform, its
  power.can_wakeup flag is set and its power.should_wakeup flag is
  unset as appropriate.

* Make ACPI set the power.can_wakeup flag for devices found to be
  wake-up capable by it.

* Make the ACPI wake-up code enable/disable GPEs for devices that
  have the wakeup.flags.prepared flag set (which means that their
  wake-up power has been enabled).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-07-07 16:26:28 -07:00
Rafael J. Wysocki
961d9120fa PCI: Introduce platform_pci_power_manageable function
Introduce function pointer platform_pci_power_manageable to be used
by the platform-related code to point to a function allowing us to
check if given device is power manageable by the platform.

Introduce acpi_pci_power_manageable() playing that role for ACPI.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-07-07 16:25:10 -07:00
Benjamin Li
99cb233d60 PCI: Limit VPD read/write lengths for Broadcom 5706, 5708, 5709 rev.
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
VPD end tag will hang the device.  This problem was initially
observed when a vpd entry was created in sysfs
('/sys/bus/pci/devices/<id>/vpd').   A read to this sysfs entry
will dump 32k of data.  Reading a full 32k will cause an access
beyond the VPD end tag causing the device to hang.  Once the device
is hung, the bnx2 driver will not be able to reset the device.
We believe that it is legal to read beyond the end tag and
therefore the solution is to limit the read/write length.

A majority of this patch is from Matthew Wilcox who gave code for
reworking the PCI vpd size information.  A PCI quirk added for the
Broadcom NIC's to limit the read/write's.

Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-07-02 11:25:54 -07:00
Jesse Barnes
53eb2fbeb9 Merge branch 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 into linux-next 2008-06-12 12:06:58 -07:00
Rafael J. Wysocki
8d2bdf4948 PCI ACPI: Drop the second argument of platform_pci_choose_state
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-06-11 19:33:19 -04:00
Alex Chiang
f46753c5e3 PCI: introduce pci_slot
Currently, /sys/bus/pci/slots/ only exposes hotplug attributes when a
hotplug driver is loaded, but PCI slots have attributes such as address,
speed, width, etc.  that are not related to hotplug at all.

Introduce pci_slot as the primary data structure and kobject model.
Hotplug attributes described in hotplug_slot become a secondary
structure associated with the pci_slot.

This patch only creates the infrastructure that allows the separation of
PCI slot attributes and hotplug attributes.  In this patch, the PCI
hotplug core remains the only user of this infrastructure, and thus,
/sys/bus/pci/slots/ will still only become populated when a hotplug
driver is loaded.

A later patch in this series will add a second user of this new
infrastructure and demonstrate splitting the task of exposing pci_slot
attributes from hotplug_slot attributes.

  - Make pci_slot the primary sysfs entity. hotplug_slot becomes a
    subsidiary structure.
    o pci_create_slot() creates and registers a slot with the PCI core
    o pci_slot_add_hotplug() gives it hotplug capability

  - Change the prototype of pci_hp_register() to take the bus and
    slot number (on parent bus) as parameters.

  - Remove all the ->get_address methods since this functionality is
    now handled by pci_slot directly.

[achiang@hp.com: rpaphp-correctly-pci_hp_register-for-empty-pci-slots]
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: make headers_check happy]
[akpm@linux-foundation.org: nuther build fix]
[akpm@linux-foundation.org: fix typo in #include]
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-06-10 14:37:03 -07:00
Ben Hutchings
94e6108803 PCI: Expose PCI VPD through sysfs
Vital Product Data (VPD) may be exposed by PCI devices in several
ways.  It is generally unsafe to read this information through the
existing interfaces to user-land because of stateful interfaces.

This adds:
- abstract operations for VPD access (struct pci_vpd_ops)
- VPD state information in struct pci_dev (struct pci_vpd)
- an implementation of the VPD access method specified in PCI 2.2
  (in access.c)
- a 'vpd' binary file in sysfs directories for PCI devices with VPD
  operations defined

It adds a probe for PCI 2.2 VPD in pci_scan_device() and release of
VPD state in pci_release_dev().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-20 21:47:07 -07:00
Greg Kroah-Hartman
fd7d1ced29 PCI: make pci_bus a struct device
This moves the pci_bus class device to be a real struct device and at
the same time, place it in the device tree in the correct location.

Note, the old "bridge" symlink is now gone, but this was a non-standard
link and no userspace program used it.  If you need to determine the
device that the bus is on, follow the standard device symlink, or walk
up the device tree.


Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 15:04:31 -08:00
Greg Kroah-Hartman
367b09fec4 PCI: fix codingstyle issues in drivers/pci/pci.h
Fixes a few coding style issues in the internal pci.h file

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 15:04:31 -08:00
Linas Vepstas
94688cf245 PCI: export pci_restore_msi_state()
PCI error recovery usually involves the PCI adapter being reset.
If the device is using MSI, the reset will cause the MSI state
to be lost; the device driver needs to restore the MSI state.

The pci_restore_msi_state() routine is currently protected
by CONFIG_PM; remove this, and also export the symbol, so
that it can be used in a modle.

Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 15:04:22 -08:00
Keshavamurthy, Anil S
994a65e25d Intel IOMMU: PCI generic helper function
When devices are under a p2p bridge, upstream transactions get replaced by the
device id of the bridge as it owns the PCIE transaction.  Hence its necessary
to setup translations on behalf of the bridge as well.  Due to this limitation
all devices under a p2p share the same domain in a DMAR.

We just cache the type of device, if its a native PCIe device
or not for later use.

[akpm@linux-foundation.org: BUG_ON -> WARN_ON+recover]
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-22 08:13:18 -07:00
Linus Torvalds
6a84258e5f Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (37 commits)
  PCI: merge almost all of pci_32.h and pci_64.h together
  PCI: X86: Introduce and enable PCI domain support
  PCI: Add 'nodomains' boot option, and pci_domains_supported global
  PCI: modify PCI bridge control ISA flag for clarity
  PCI: use _CRS for PCI resource allocation
  PCI: avoid P2P prefetch window for expansion ROMs
  PCI: skip ISA ioresource alignment on some systems
  PCI: remove transparent bridge sizing
  pci: write file size to inode on proc bus file write
  pci: use size stored in proc_dir_entry for proc bus files
  pci: implement "pci=noaer"
  PCI: fix IDE legacy mode resources
  MSI: Use correct data offset for 32-bit MSI in read_msi_msg()
  PCI: Fix incorrect argument order to list_add_tail() in PCI dynamic ID code
  PCI: i386: Compaq EVO N800c needs PCI bus renumbering
  PCI: Remove no longer correct documentation regarding MSI vector assignment
  PCI: re-enable onboard sound on "MSI K8T Neo2-FIR"
  PCI: quirk_vt82c586_acpi: Omit reading PCI revision ID
  PCI: quirk amd_8131_mmrbc: Omit reading pci revision ID
  cpqphp: Use PCI_CLASS_REVISION instead of PCI_REVISION_ID for read
  ...
2007-10-12 15:50:23 -07:00
Randy Dunlap
7f78576366 pci: implement "pci=noaer"
For cases in which CONFIG_PCIEAER=y (such as distro kernels), allow users
to disable PCIE Advanced Error Reporting by using "pci=noaer" on the
kernel command line.

This can be used to work around hardware or (kernel) software problems.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 15:03:17 -07:00
Kay Sievers
7eff2e7a8b Driver core: change add_uevent_var to use a struct
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.

Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.

Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:51:01 -07:00