Commit Graph

353 Commits

Author SHA1 Message Date
Jeff Kirsher
2d0bb1c1f4 e100/e1000*/igb*/ixgb*: Add missing read memory barrier
Based on patches from Sonny Rao and Milton Miller...

Combined the patches to fix up clean_tx_irq and clean_rx_irq.

The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.

In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.

The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.

This bug was found during stress testing and adding this barrier has
been shown to fix it.  The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().

This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.

Previously Submitted to e1000-devel only for ixgbe

http://marc.info/?l=e1000-devel&m=126593062701537&w=3

We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.

CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-08 20:02:45 -07:00
Linus Torvalds
6ba74014c1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
  phy/marvell: add 88ec048 support
  igb: Program MDICNFG register prior to PHY init
  e1000e: correct MAC-PHY interconnect register offset for 82579
  hso: Add new product ID
  can: Add driver for esd CAN-USB/2 device
  l2tp: fix export of header file for userspace
  can-raw: Fix skb_orphan_try handling
  Revert "net: remove zap_completion_queue"
  net: cleanup inclusion
  phy/marvell: add 88e1121 interface mode support
  u32: negative offset fix
  net: Fix a typo from "dev" to "ndev"
  igb: Use irq_synchronize per vector when using MSI-X
  ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
  e1000e: Fix irq_synchronize in MSI-X case
  e1000e: register pm_qos request on hardware activation
  ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
  net: Add getsockopt support for TCP thin-streams
  cxgb4: update driver version
  cxgb4: add new PCI IDs
  ...

Manually fix up conflicts in:
 - drivers/net/e1000e/netdev.c: due to pm_qos registration
   infrastructure changes
 - drivers/net/phy/marvell.c: conflict between adding 88ec048 support
   and cleaning up the IDs
 - drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
   conflict (registration change vs marking it static)
2010-08-04 11:47:58 -07:00
Bruce Allan
96f2bd13bf e1000e: correct MAC-PHY interconnect register offset for 82579
The MAC-PHY interconnect register set on ICH/PCH parts is accessed through
a peephole mechanism by writing an offset to a CSR register.  The offset
for the interconnect's half-duplex control register (which is used in a
jumbo frame workaround for 82579) is incorrect.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-03 16:40:53 -07:00
David S. Miller
00dad5e479 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/e1000e/hw.h
	net/bridge/br_device.c
	net/bridge/br_input.c
2010-08-02 22:22:46 -07:00
Jeff Kirsher
8e86acd7d5 e1000e: Fix irq_synchronize in MSI-X case
Based on original patch/work from Jean Delvare <jdelvare@suse.de>
Synchronize all IRQs when in MSI-X IRQ mode.

Jean's original patch hard coded the sync with the 3 possible vectors,
this patch incorporates more flexibility for the future and aligns
with how igb stores the number of vectors into the adapter structure.

CC: Jean Delvare <jdelvare@suse.de>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-02 21:20:21 -07:00
Florian Mickler
c128ec2920 e1000e: register pm_qos request on hardware activation
The pm_qos_add_request call has to register the pm_qos request with the pm_qos
susbsystem before first use of the pm_qos request via
pm_qos_update_request.

As pm_qos changed to use plists there is no benefit in registering and
unregistering the pm_qos request on ifup/ifdown and thus we move the
registering into e1000_open and the unregistering in e1000_close.

This fixes the following warning:

[    1.786060] WARNING: at kernel/pm_qos_params.c:264
pm_qos_update_request+0x28/0x54()
[    1.786088] Hardware name: Latitude E6500
[    1.787045] pm_qos_update_request() called for unknown object
[    1.787966] Modules linked in:
[    1.788940] Pid: 1, comm: swapper Not tainted 2.6.35-rc5-mmotm0719 #1
[    1.790035] Call Trace:
[    1.791121]  [<ffffffff81037335>] warn_slowpath_common+0x80/0x98
[    1.792205]  [<ffffffff810373e1>] warn_slowpath_fmt+0x41/0x43
[    1.793279]  [<ffffffff81057c14>] pm_qos_update_request+0x28/0x54
[    1.794347]  [<ffffffff8134889e>] e1000_configure+0x421/0x459
[    1.795393]  [<ffffffff8134afbd>] e1000_open+0xbd/0x37c
[    1.796436]  [<ffffffff8105743a>] ? raw_notifier_call_chain+0xf/0x11
[    1.797491]  [<ffffffff8145f948>] __dev_open+0xae/0xe2
[    1.798547]  [<ffffffff8145f997>] dev_open+0x1b/0x49
[    1.799612]  [<ffffffff8146e36e>] netpoll_setup+0x84/0x259
[    1.800685]  [<ffffffff81b5037c>] init_netconsole+0xbc/0x21f
[    1.801744]  [<ffffffff81b5026c>] ? sir_wq_init+0x0/0x35
[    1.802793]  [<ffffffff81b502c0>] ? init_netconsole+0x0/0x21f
[    1.803845]  [<ffffffff810002ff>] do_one_initcall+0x7a/0x12f
[    1.804885]  [<ffffffff81b2ccae>] kernel_init+0x138/0x1c2
[    1.805915]  [<ffffffff81003554>] kernel_thread_helper+0x4/0x10
[    1.806937]  [<ffffffff81590e00>] ? restore_args+0x0/0x30
[    1.807955]  [<ffffffff81b2cb76>] ? kernel_init+0x0/0x1c2
[    1.808958]  [<ffffffff81003550>] ? kernel_thread_helper+0x0/0x10
[    1.809958] ---[ end trace 84b562a00a60539e ]---

Signed-off-by: Florian Mickler <florian@mickler.org>
Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-02 21:20:20 -07:00
Bruce Allan
ff847ac2d3 e1000e: 82577/82578 PHY register access issues
The MAC-PHY interconnect on 82577/82578 uses a power management feature
(called K1) which must be disabled when in 1Gbps due to a hardware issue on
these parts.  The #define bit setting used to enable/disable K1 is
incorrect and can cause PHY register accesses to stop working altogether
until the next device reset.  This patch sets the register correctly.

This issue is present in kernels since 2.6.32.

CC: stable@kernel.org
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-27 21:06:26 -07:00
Jean Delvare
ea7afd31fb e1000e: Drop a useless statement
err is set again a few lines below.

Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-26 18:42:52 -07:00
James Bottomley
82f682514a pm_qos: Get rid of the allocation in pm_qos_add_request()
All current users of pm_qos_add_request() have the ability to supply
the memory required by the pm_qos routines, so make them do this and
eliminate the kmalloc() with pm_qos_add_request().  This has the
double benefit of making the call never fail and allowing it to be
called from atomic context.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-07-19 02:00:34 +02:00
Bruce Allan
5a86f28f95 e1000e: disable EEE support by default
Based on community feedback, EEE should be disabled by default until the
IEEE802.3az specification has been finalized.

Cc: bhutchings@solarflare.com
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29 23:09:19 -07:00
Bruce Allan
cc40f57a76 e1000e: remove EEE module parameter
As requested by Dave Miller.  A follow-on set of patches will allow for
ethtool to enable/disable the feature instead.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29 23:09:19 -07:00
Bruce Allan
8eb64e6b85 e1000e: suppress compile warnings on certain archs
Commit 84f4ee902a causes compile warnings on
architectures that have unsigned long long's that are not 64-bit, e.g.
ia64.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29 23:09:18 -07:00
Dean Nelson
36f2407fe5 e1000e: don't inadvertently re-set INTX_DISABLE
Should e1000_test_msi() fail to see an msi interrupt, it attempts to
fallback to legacy INTx interrupts. But an error in the code may prevent
this from happening correctly.

Before calling e1000_test_msi_interrupt(), e1000_test_msi() disables SERR
by clearing the SERR bit from the just read PCI_COMMAND bits as it writes
them back out.

Upon return from calling e1000_test_msi_interrupt(), it re-enables SERR
by writing out the version of PCI_COMMAND it had previously read.

The problem with this is that e1000_test_msi_interrupt() calls
pci_disable_msi(), which eventually ends up in pci_intx(). And because
pci_intx() was called with enable set to 1, the INTX_DISABLE bit gets
cleared from PCI_COMMAND, which is what we want. But when we get back to
e1000_test_msi(), the INTX_DISABLE bit gets inadvertently re-set because
of the attempt by e1000_test_msi() to re-enable SERR.

The solution is to have e1000_test_msi() re-read the PCI_COMMAND bits as
part of its attempt to re-enable SERR.

During debugging/testing of this issue I found that not all the systems
I ran on had the SERR bit set to begin with. And on some of the systems
the same could be said for the INTX_DISABLE bit. Needless to say these
latter systems didn't have a problem falling back to legacy INTx
interrupts with the code as is.

Signed-off-by: Dean Nelson <dnelson@redhat.com>
CC: stable@kernel.org
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29 23:09:18 -07:00
Stanislaw Gruszka
52b6dcfe59 e1000e: fail when try to setup unsupported features
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29 00:53:25 -07:00
Bruce Allan
17f085df92 e1000e: disable gig speed when in S0->Sx transition
Most of this workaround is necessary for all ICHx/PCH parts so one of
the two MAC-type checks can be removed.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 12:58:40 -07:00
Bruce Allan
dbcb9fec5c e1000e: packet split should not be used with early receive
Originally it was thought there were issues with ICHx/PCH parts with packet
split when jumbo frames were enabled but in fact it is really only when
early-receive is enabled (via ERT register) on these parts.  Use packet
split with jumbos but only when early-receive is not enabled.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 12:58:39 -07:00
Bruce Allan
f2e2b3abe4 e1000e: do not touch PHY page 800 registers when link speed is 1000Mbps
The PHY on 82577/82578 has issues when the registers on page 800 are
accessed when in gigabit mode.  Do not clear the Wakeup Control register
when resetting the part since it is on page 800 (and will be cleared on
reset anyway).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 12:58:39 -07:00
Bruce Allan
0c6bdb3084 e1000e: avoid polling h/w registers during link negotiation
Avoid touching hardware registers when possible, otherwise link negotiation
can get messed up when user-level scripts are rapidly polling the driver to
see if/when link is up.  Use the saved link state information instead when
possible.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 12:58:38 -07:00
Bruce Allan
c14c643b3d e1000e: update driver version number
Also separate out an _EXTRAVERSION similar to the core kernel.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18 22:12:18 -07:00
Bruce Allan
451152d97f e1000e: update copyright information
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18 22:12:18 -07:00
Bruce Allan
e52997f960 e1000e: enable support for EEE on 82579
This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the
new 82579 LOMs.  An optional module parameter is provided to disable the
feature if desired.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18 22:12:17 -07:00
Bruce Allan
d3738bb820 e1000e: initial support for 82579 LOMs
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18 22:12:16 -07:00
Bruce Allan
eb7700dc03 e1000e: fix check for manageability on ICHx/PCH
Do not check for all the bits in E1000_FWSM_MODE_MASK when checking for
manageability on 82577/82578; only check if iAMT is enabled.  Both of the
manageability checks (for 82577/82578 and ICHx) must check the firmware
valid bit too since the other bits are only valid when the latter is set.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18 22:12:16 -07:00
Bruce Allan
8c7bbb9253 e1000e: separate out PHY statistics register updates
The 82577/82578 parts have half-duplex statistics in PHY registers.  These
need only be read when in half-duplex and should all be read at once rather
than one at a time to prevent excessive cycles of acquiring/releasing the
PHY semaphore.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18 22:12:15 -07:00
Bruce Allan
3f0c16e844 e1000e: cleanup e1000_sw_lcd_config_ich8lan()
Do not acquire and release the PHY unnecessarily for parts that return
from this workaround without actually accessing the PHY registers.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18 22:12:15 -07:00
Bruce Allan
3af50481ee e1000e: cleanup ethtool loopback setup code
Refactor the loopback setup code to first handle the only 10/100 PHY
supported by the driver if applicable and then handle the 1Gig PHYs in a
switch statement for PHY-specific setups.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18 22:12:14 -07:00
Dan Carpenter
3b21b508ec e1000e: change logical negate to bitwise
The bitwise negate is intended here.  With the logical negate the
condition is always false.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03 03:28:21 -07:00
Linus Torvalds
f8965467f3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
2010-05-20 21:04:44 -07:00
Joe Perches
a4b770972b drivers/net: Remove unnecessary returns from void function()s
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

It also does not remove null void functions with return.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

with some cleanups by hand.

Compile tested x86 allmodconfig only.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14 00:19:28 -07:00
Bruce Allan
10df0b9116 e1000e: add PCI device id to enable support for 82567V-4
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:15 -07:00
Bruce Allan
e98cac447c e1000e: Fix/cleanup PHY reset code for ICHx/PCHx
i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling
e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to
make sure the MAC had completed the PHY configuration.  However,
e1000_lan_init_done_ich8lan() had already been called in one of the two
places where PHY reset occurs for ICHx/PCHx parts, which caused the second
call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already
been checked and cleared.

ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset
in e1000_reset_hw_ich8lan() and the PHY-only reset in
e1000_phy_hw_reset_ich8lan().  There was duplicate code in both paths to be
performed post-reset that are now combined into one new function -
e1000_post_phy_reset_ich8lan().  This cleanup also included moving the
clearing of the PHY Reset Asserted bit in the STATUS register (now done for
all ICH/PCH parts) and the check for the indication from h/w that basic
configuration has completed back to where it previously was in
e1000_get_cfg_done_ich8lan().

iii) Corrected a few comments

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:14 -07:00
Bruce Allan
a305595b12 e1000e: move settting of flow control refresh timer to link setup code
The flow control refresh timer value needs to be saved off so that it can
be programmed into the approrpiate register when applicable but without a
reset, e.g. when changing flow control parameters via ethtool.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:13 -07:00
Bruce Allan
a65a4a0d51 e1000e: fix checks for manageability enabled and management pass-through
The mac->arc_subsystem was being incorrectly used to flag whether or not
manageability was enabled when it should only be used to state whether the
ARC (Host interface) subsystem is available on a particular MAC _and_ only
valid when any manageability is enabled. The ARC subsystem is currently
only available on 80003es2lan and 82573 parts supported by the driver.

A new flag, has_fwsm, is introduced to be used when checking if
manageability is enabled but only on parts that acutally have an FWSM
register. While the above parts have an FWSM register, there are other
parts that have FWSM but do not have support for the ARC subsystem,
namely 82571/2 and ICHx/PCH.

And then there are parts that have manageability, but do not have either
FWSM register or support for the ARC subsystem - these are 82574 and 82583.

For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no
functional changes, it only corrects the usage of the manageability flags.
For 82574 and 82583, it fixes the incorrect accesses of the non-existent
FWSM register and ARC subsystem as well as corrects the check for
management pass-through.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:13 -07:00
Bruce Allan
eab50ffb22 e1000e: Incorrect function pointer set for force_speed_duplex on 82577
The force_speed_duplex function pointer was incorrectly set.  Instead of
calling the 82577-specific version it was calling the m88 version which,
among other incorrect things, reset the PHY causing autonegotiation to be
re-enabled in the PHY resulting in the link defaulting to half-duplex.
The 82577-specific force_speed_duplex function also had an issue where
it disabled Auto-MDI-X which caused the link to not come up.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:12 -07:00
Bruce Allan
8b802a7e94 e1000e: Cleanup e1000_sw_lcd_config_ich8lan()
After every reset all ICH/PCH parts call this function which acquires the
swflag, performs a workaround on applicable parts and releases the swflag.
There is no reason for parts for which this workaround is not applicable
to acquire and release the swflag so the function should just return
without doing anything for these parts.  This also provides for the
indentation of most of the function contents to be shifted left cleaning up
the code.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:12 -07:00
Bruce Allan
757c530407 e1000e: Remove EN_MAC_ADDR_FILTER check from enable_mng_pass_thru check
Patch addresses issues when manageability passthrough is enabled, but the
MAC_ADDR_FILTER bit is not set in the MANC register.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:11 -07:00
Bruce Allan
9c5e209d4b e1000e: cleanup multiple common exit points
...in e1000_update_nvm_checksum_ich8lan().

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:11 -07:00
Bruce Allan
52a9b23196 e1000e: s/w initiated LSC MSI-X interrupts not generated; no transmit
In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was
blocked), the LSC interrupt generated by s/w to start the watchdog which
started the transmitter was not getting fired by the hardware because bit
24 (the 'other' cause bit) also needed to be set.  Without an active SoL
session, the PHY was reset which caused the h/w to fire the LSC interrupt.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:10 -07:00
Bruce Allan
cd791618c2 e1000e: initialize manageability (IPMI) pass-through in 82574/82583
82574/82583 uses different registers/bits to setup manageability filters
than all other parts supported by e1000e; set them accordingly for IPMI
pass-through.  Rename the function to better reflect what it does.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:10 -07:00
Bruce Allan
11b08be830 e1000e: bad state after running ethtool diagnostics with AMT enabled
When running ethtool online diagnostics with no open interface, there is a
short period of time where the driver relinquishes control of the adapter
during which time AMT (manageability firmware) can put the adapter into an
unknown state resulting in such things as link test failure, hardware hang,
reporting an incorrect link speed, etc.  Resetting the adapter during an
open() resolves this by putting the adapter into a quiescent state.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:09 -07:00
Bruce Allan
4fe4491fc5 e1000e: use static params to save stack space (part 2)
A couple stack cleanups missed in an earlier patch from Jesse.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12 23:31:09 -07:00
Mark Gross
ed77134bfc PM QOS update
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation.  I did this because request more
accurately represents what it actually does.

Also, I added a string based ABI for users wanting to use a string
interface.  So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface.  (someone asked me for it and I don't think
it hurts anything.)

This patch updates some documentation input I got from Randy.

Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-05-10 23:08:19 +02:00
Bruce Allan
627c8a041f e1000e: Reset 82577/82578 PHY before first PHY register read
Reset the PHY before first accessing it.  Doing so, ensure that the PHY is
in a known good state before we read/write PHY registers. This fixes a
driver probe failure.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06 01:31:28 -07:00
Bruce Allan
6dfaa76994 e1000e: reset MAC-PHY interconnect on 82577/82578 during Sx->S0
During Sx->S0 transitions, the interconnect between the MAC and PHY on
82577/82578 can remain in SMBus mode instead of transitioning to the
PCIe-like mode required during normal operation.  Toggling the LANPHYPC
Value bit essentially resets the interconnect forcing it to the correct
mode.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06 01:31:28 -07:00
Jesse Brandeburg
eab2abf582 e1000/e1000e: implement a simple interrupt moderation
Back before e1000-7.3.20, the e1000 driver had a simple algorithm that
managed interrupt moderation.  The driver was updated in 7.3.20 to
have the new "adaptive" interrupt moderation but we have customer
requests to redeploy the old way as an option.  This patch adds the
old functionality back.  The new functionality can be enabled via
module parameter or at runtime via ethtool.
Module parameter: (InterruptThrottleRate=4) to use this new
moderation method.
Ethtool method: ethtool -C ethX rx-usecs 4

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05 21:15:32 -07:00
Alexander Duyck
edf15c1742 e1000e: increase rx fifo size to 36K on 82574 and 82583
This change increases the RX fifo size to 36K for standard frames and
decreases the TX fifo size to 4K.  The reason for this change is that on
slower systems the RX is much more likely to backfill and need space than
the TX is.  As long as the TX fifo is twice the size of the MTU we should
have more than enough TX fifo.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05 21:15:31 -07:00
Tom Herbert
f85e4dfac6 e1000e: Save irq into netdev structure
Set net->devirq to pdev->irq.  This should be consistent with other
drivers.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05 21:11:26 -07:00
Tom Herbert
c72ea83d39 e1000e: Remove unnessary log message
Remove e_info message printed whenever TSO is enabled or disabled.
This is not very useful and just clutters dmesg.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05 21:11:26 -07:00
Tom Herbert
50849d792b e1000e: reduce writes of RX producer ptr
Reduce number of writes to RX producer pointer.   When alloc'ing RX
buffers, only write the RX producer pointer once every
E1000_RX_BUFFER_WRITE (16) buffers created.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05 21:11:25 -07:00
Tom Herbert
9ed318d546 e1000e: save skb counts in TX to avoid cache misses
In e1000_tx_map, precompute number of segements and bytecounts which
are derived from fields in skb; these are stored in buffer_info.  When
cleaning tx in e1000_clean_tx_irq use the values in the associated
buffer_info for statistics counting, this eliminates cache misses
on skb fields.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05 21:11:25 -07:00