Port autoselection done by kernel only works when number of bound
sockets is under a threshold (typically 30000).
When this threshold is over, we must check if there is a conflict before
exiting first loop in inet_csk_get_port()
Change inet_csk_bind_conflict() to forbid two reuse-enabled sockets to
bind on same (address,port) tuple (with a non ANY address)
Same change for inet6_csk_bind_conflict()
Reported-by: Gaspar Chilingarov <gasparch@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sky2 status ring must be big enough to handle worst case number
of status messages. It was being oversized (to handle dual port cards),
and excessive number of tx ring entries were allowed. This patch reduces
the footprint and makes sure the value is enough.
Later patch to add RSS increases the number of possible Rx status elements.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove DCB_PROTO_VERSION as we don't do netlink versioning
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change magic numbers to identifiers for X25 interface.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change magic numbers to identifiers for X25 interface.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change magic numbers to identifiers for X25 interface.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change magic numbers to identifiers for X25 interface.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change magic numbers to identifiers for X25 interface.
also minor check patch formatting.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Acked-by: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
V2 Feedback from John Hughes.
- Add header for userspace implementations such as xot/xoe to use
- Use explicit values for interface stability
- No changes to driver patches
V1
- Use identifiers instead of magic numbers for X25 layer 3 to device interface.
- Also fixed checkpatch notes on updated code.
[ Add new user header to include/linux/Kbuild -DaveM ]
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an SKF_AD_HATYPE field to the packet ancilliary data area, giving
access to skb->dev->type, as reported in the sll_hatype field.
When capturing packets on a PF_PACKET/SOCK_RAW socket bound to all
interfaces, there doesn't appear to be a way for the filter program to
actually find out the underlying hardware type the packet was captured
on. This patch adds such ability.
This patch also handles the case where skb->dev can be NULL, such as on
netlink sockets.
Signed-off-by: Paul Evans <leonerd@leonerd.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account for TSO segments of an skb in TCP_MIB_OUTSEGS counter. Without
doing this, the counter can be off by orders of magnitude from the
actual number of segments sent.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, the "goto out" calls "rdma_destroy_id(cm_id);"
That isn't needed here and would cause problems because "cm_id" is an
ERR_PTR. The new code just returns directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, if rtnl_create_link() returned an ERR_PTR then that
would get passed to rtnl_configure_link() which dereferences it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to indicate IDC(fw recovery) changes.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do netif_device_attach, even if resource allocation fails.
Driver callbacks can be called, if device is attached.
All these callbacks need to be protected by ADAPTER_UP_MAGIC check.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rcv producer value should be read in spin-lock.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should not go ahead with fw recovery if fails to acquire
semaphore.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defining macro to set and clear driver state.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now any pci-func can start fw, whoever sees the reset ack first.
Before this, pci-func which sets the RESET state has the responsibility
to start fw.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different class of drivers co-exist for CNA device,
there is some minimal interaction that will be required amongst
the drivers for performing some device level operations.
All the driver should follow inter driver coexistence document.
Fixing polling interval and spelling mistake.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added additional driver statistics to track errors in rcv/tx path.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPv6 support for RFC5082 Generalized TTL Security Mechanism.
Not to users of mapped address; the IPV6 and IPV4 socket options are seperate.
The server does have to deal with both IPv4 and IPv6 socket options
and the client has to handle the different for each family.
On client:
int ttl = 255;
getaddrinfo(argv[1], argv[2], &hint, &result);
for (rp = result; rp != NULL; rp = rp->ai_next) {
s = socket(rp->ai_family, rp->ai_socktype, rp->ai_protocol);
if (s < 0) continue;
if (rp->ai_family == AF_INET) {
setsockopt(s, IPPROTO_IP, IP_TTL, &ttl, sizeof(ttl));
} else if (rp->ai_family == AF_INET6) {
setsockopt(s, IPPROTO_IPV6, IPV6_UNICAST_HOPS,
&ttl, sizeof(ttl)))
}
if (connect(s, rp->ai_addr, rp->ai_addrlen) == 0) {
...
On server:
int minttl = 255 - maxhops;
getaddrinfo(NULL, port, &hints, &result);
for (rp = result; rp != NULL; rp = rp->ai_next) {
s = socket(rp->ai_family, rp->ai_socktype, rp->ai_protocol);
if (s < 0) continue;
if (rp->ai_family == AF_INET6)
setsockopt(s, IPPROTO_IPV6, IPV6_MINHOPCOUNT,
&minttl, sizeof(minttl));
setsockopt(s, IPPROTO_IP, IP_MINTTL, &minttl, sizeof(minttl));
if (bind(s, rp->ai_addr, rp->ai_addrlen) == 0)
break
...
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way GSO packets don't get handled differently.
With help from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
If some skb are queued to our backlog, we are delaying IPI sending at
the end of net_rx_action(), increasing latencies. This defeats the
queueing, since we want to quickly dispatch packets to the pool of
worker cpus, then eventually deeply process our packets.
It's better to send IPI before processing our packets in upper layers,
from process_backlog().
Change the _and_disable_irq suffix to _and_enable_irq(), since we enable
local irq in net_rps_action(), sorry for the confusion.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also put t4_write_indirect() inside "#if 0" to avoid a "defined but not
used" compile warning.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct direction of byte-swapping function to fix a mistake
shown by sparse endianness checking -- c.fl0id is __be16.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue raises when having 2 NICs both assigned the same
IPv6 global address.
If a sender binds to a particular NIC (SO_BINDTODEVICE),
the outgoing traffic is being sent via the first found.
The bonded device is thus not taken into an account during the
routing.
From the ip6_route_output function:
If the binding address is multicast, linklocal or loopback,
the RT6_LOOKUP_F_IFACE bit is set, but not for global address.
So binding global address will neglect SO_BINDTODEVICE-binded device,
because the fib6_rule_lookup function path won't check for the
flowi::oif field and take first route that fits.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Scott Otto <scott.otto@alcatel-lucent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric's recent patch added __force, but this
place would seem to require actually doing
a byte order conversion so the printk is
consistent across architectures.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point, skb->destructor is not the original one (stored in
DEV_GSO_CB(skb)->destructor)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC2460, PMTU is set to the IPv6 Minimum Link
MTU (1280) and a fragment header should always be included
after a node receiving Too Big message reporting PMTU is
less than the IPv6 Minimum Link MTU.
After receiving a ICMPv6 Too Big message reporting PMTU is
less than the IPv6 Minimum Link MTU, sctp *can't* send any
data/control chunk that total length including IPv6 head
and IPv6 extend head is less than IPV6_MIN_MTU(1280 bytes).
The failure occured in p6_fragment(), about reason
see following(take SHUTDOWN chunk for example):
sctp_packet_transmit (SHUTDOWN chunk, len=16 byte)
|------sctp_v6_xmit (local_df=0)
|------ip6_xmit
|------ip6_output (dst_allfrag is ture)
|------ip6_fragment
In ip6_fragment(), for local_df=0, drops the the packet
and returns EMSGSIZE.
The patch fixes it with adding check length of skb->len.
In this case, Ipv6 not to fragment upper protocol data,
just only add a fragment header before it.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new driver to use tethering with an iPhone device. After initial submission,
apply fixes to fit the new driver into the kernel standards.
There are still a couple of minor (almost cosmetic-level) issues, but the driver
is fully functional right now.
Signed-off-by: L. Alberto Giménez <agimenez@sysvalve.es>
Signed-off-by: Diego Giagio <diego@giagio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Force serialization of userspace-triggered DLPAR/mem operations
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset a port's resources only if they're actually in an error state
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I encountered an issue that not to link up on cxgb3 fabric.
I bisected and found that this regression was introduced by
0f07c4ee8c.
Correct to pass phy_addr to cphy_init() at t3_xaui_direct_phy_prep().
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform data to the ks8842 driver.
Via the platform data a MAC address, to be used by the controller,
can be passed.
To ensure this MAC address is used, the MAC address is written
after each hardware reset.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1, An X25 program binds and listens
2, calls arrive waiting to be accepted
3, Program exits without accepting
4, Sockets time out but don't get correctly cleaned up
5, cat /proc/net/x25/socket shows the dead sockets with bad inode fields.
This line borrowed from AX25 sets the dying socket so the timers clean up later.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL pointer dereference in ks8851_tx_work by checking if dequeued
list is already empty before writing the packet to TX FIFO
Unable to handle kernel NULL pointer dereference at virtual address 00000050
PC is at ks8851_tx_work+0xdc/0x1b0
LR is at wait_for_common+0x148/0x164
pc : [<c01c0df4>] lr : [<c025a980>] psr: 20000013
Backtrace:
ks8851_tx_work+0x0/0x1b0
worker_thread+0x0/0x190
kthread+0x0/0x90
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the stats counter calculation in 3c574_cs, similar
to the method used in 3c589_cs. This corrects the contents
of the counter on tests using a "Megahertz 574B" card.
[linux@dominikbrodowski.net: clean up commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building a bundle, we set dst.dev and rt6.rt6i_idev.
We must ensure to set the same device for both fields.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the always true #if 1. Also the unecessary re-test of ei_local->irqlock
and the unreachable printk format string.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
kill_fasync() uses a central rwlock, candidate for RCU conversion, to
avoid cache line ping pongs on SMP.
fasync_remove_entry() and fasync_add_entry() can disable IRQS on a short
section instead during whole list scan.
Use a spinlock per fasync_struct to synchronize kill_fasync_rcu() and
fasync_{remove|add}_entry(). This spinlock is IRQ safe, so sock_fasync()
doesnt need its own implementation and can use fasync_helper(), to
reduce code size and complexity.
We can remove __kill_fasync() direct use in net/socket.c, and rename it
to kill_fasync_rcu().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ems_usb_probe(), a pointer is dereferenced after making sure it is NULL...
This patch replaces netdev->dev.parent with &intf->dev in dev_err() calls to
avoid this.
Signed-off-by: "Hans J. Koch" <hjk@linutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I updated this from the corresponding
userspace library, an annotation error crept
in -- this variable needs to be annotated as
little endian. No effect on code generation.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes ar5416Addac_9160 and ar5416Addac_9160 const
I guess we skipped them long ago.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 6651ffc8e8
("ipv6: Fix tcp_v6_send_response transport header setting.")
fixed one half of why ipv6 tcp response checksums were
invalid, but it's not the whole story.
If we're going to use CHECKSUM_PARTIAL for these things (which we are
since commit 2e8e18ef52 "tcp: Set
CHECKSUM_UNNECESSARY in tcp_init_nondata_skb"), we can't be setting
buff->csum as we always have been here in tcp_v6_send_response. We
need to leave it at zero.
Kill that line and checksums are good again.
Signed-off-by: David S. Miller <davem@davemloft.net>
