* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin serial driver: fix up tty core set_ldisc API change breakage bug
Blackfin arch: protect only the SPI bus controller with CONFIG_SPI_BFIN
Blackfin arch: fixup warnings with the new cplb saved values
Blackfin Serial Driver: Clean up BF54x macro in blackfin UART driver.
- No need to perform data_len = 0 in the switch command, since data_len
is initialized to 0 in the beginning of the ipq_build_packet_message()
method.
- {ip,ip6}_queue: We can reach nlmsg_failure only from one place; skb is
sure to be NULL when getting there; since skb is NULL, there is no need
to check this fact and call kfree_skb().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes nf_ct_ipv4_ct_gather_frags() method declaration from
include/net/netfilter/ipv4/nf_conntrack_ipv4.h, since it is unused in
the Linux kernel.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a conntrack is destroyed, the connection status does not get
exported to netlink. I don't see a reason for not doing so. This patch
exports the status on all conntrack events.
Signed-off-by: Fabian Hugelshofer <hugelshofer2006@gmx.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the last packet of a connection isn't accounted when its causing
abnormal termination.
Introduces nf_ct_kill_acct() which increments the accounting counters on
conntrack kill. The new function was necessary, because there are calls
to nf_ct_kill() which don't need accounting:
nf_conntrack_proto_tcp.c line ~847:
Kills ct and returns NF_REPEAT. We don't want to count twice.
nf_conntrack_proto_tcp.c line ~880:
Kills ct and returns NF_DROP. I think we don't want to count dropped
packets.
nf_conntrack_netlink.c line ~824:
As far as I can see ctnetlink_del_conntrack() is used to destroy a
conntrack on behalf of the user. There is an sk_buff, but I don't think
this is an actual packet. Incrementing counters here is therefore not
desired.
Signed-off-by: Fabian Hugelshofer <hugelshofer2006@gmx.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Encapsulate the common
if (del_timer(&ct->timeout))
ct->timeout.function((unsigned long)ct)
sequence in a new function.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksize() API is going away because it is being abused and it doesn't even
work consistenly across different allocators. Therefore, convert
net/netfilter/nf_conntrack_extend.c to use krealloc().
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch implements a new "security" table for iptables, so
that MAC (SELinux etc.) networking rules can be managed separately to
standard DAC rules.
This is to help with distro integration of the new secmark-based
network controls, per various previous discussions.
The need for a separate table arises from the fact that existing tools
and usage of iptables will likely clash with centralized MAC policy
management.
The SECMARK and CONNSECMARK targets will still be valid in the mangle
table to prevent breakage of existing users.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds full support for SCTP to ctnetlink. This includes three
new attributes: state, original vtag and reply vtag.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch groups ctnetlink errors into three logical sets:
* Malformed messages: if ctnetlink receives a message without some mandatory
attribute, then it returns EINVAL.
* Unsupported operations: if userspace tries to perform an unsupported
operation, then it returns EOPNOTSUPP.
* Unchangeable: if userspace tries to change some attribute of the
conntrack object that can only be set once, then it returns EBUSY.
This patch reduces the number of -EINVAL from 23 to 14 and it results in
5 -EBUSY and 6 -EOPNOTSUPP.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bindv6only is tuned via sysctl. It is already on a struct net
and per-net sysctls allow for its modification (ipv6_sysctl_net_init).
Despite this the value configured in the init net is used for the
rest of them.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first 4 bytes of data to be sent are stored additionally into
the message class field of the send request. A receiving target
program (not an af_iucv socket program) can make use of this
information to pre-screen incoming messages.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code used preempt_disable() to prevent cpu hotplug, however that
doesn't protect for cpus being added. So use get_online_cpus() instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: net/iucv/built-in.o(.exit.text+0x9c): Section mismatch in
reference from the function iucv_exit() to the variable
.cpuinit.data:iucv_cpu_notifier
This warning is caused by a reference from unregister_hotcpu_notifier()
from an exit function to a cpuinitdata annotated data structurre.
This is a false positive warning since for the non CPU_HOTPLUG case
unregister_hotcpu_notifier() is a nop.
Use __refdata instead of __cpuinitdata to get rid of the warning.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-tip testing found the following build error:
drivers/built-in.o: In function `mcs_receive_irq':
mcs7780.c:(.text+0x4e429): undefined reference to `crc32_le'
drivers/built-in.o: In function `mcs_hard_xmit':
mcs7780.c:(.text+0x4e9af): undefined reference to `crc32_le'
with:
http://redhat.com/~mingo/misc/config-Sun_Jun__8_22_56_14_CEST_2008.bad
the reason is a missing enablement of the CRC32 library in the Kconfig.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default sack frequency should be 2. Also fix copy/paste
error when updating all transports.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 5761 non-e devices, two problems prevent the administrator from
overriding the WOL settings in the device's NVRAM.
The first problem is that GPIO 0 and GPIO 2 have been swapped. This
change prevented the administrator from turning on WOL when it is
disabled in NVRAM. The fix is to add a new path for the 5761 that
swaps the two GPIOs in the code as well.
The second problem is that GPIO 1 could not be toggled by the driver
because the GPIO is shared with the debug UART GPIO. This will prevent
the administrator from being able to turn WOL off if it was enabled in
NVRAM. The fix is to always disable the debug UART after a GRC reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where the TG3_FLAG_10_100_ONLY flag was
testing against the wrong flags variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The git commit ef167e2703 entitled
"Fix supporting flowctrl code" introduced a bug that prevents 5714S,
5715S and 5780S devices from falling back to a forced link mode. The
problem is that the added flow control check will always fail if flow
control is set to autoneg and either RX or TX (or both) flow control
is enabled. The driver defaults to setting flow control to autoneg
and advertises both RX and TX flow control.
The fix is to remove the errant check.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 54d29ad33e (Power Supply: fix race
in device_create) introduced a race in power_supply_uevent. Previously it
checked that power_supply is available by checking for dev->driver_data.
But now dev->driver_data is set before power_supply->dev is initialised.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch adds a check to the set_channel flow. When attempting to change
the channel while in IBSS mode, and the new channel does not support IBSS
mode, the flow return with an error value with no consequences on the
mac80211 and driver state.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sufficient scans (at least 2 or 3) should have been done within 7
seconds to find an existing IBSS to join. This should improve IBSS
creation latency; and since IBSS merging is still in effect, shouldn't
have detrimental effects on eventual IBSS convergence.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a data alignment issue in the zd1211rw driver.
The IEEE80211_STYPE_QOS_DATA bit should be used as a bitwise test
to test for the presence of the 2 byte QoS control field.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the issue of slow reconnection to an IBSS cell after
disconnection from it. Now the interface's bssid is reset upon ifdown.
ieee80211_sta_find_ibss:
if (found && memcmp(ifsta->bssid, bssid, ETH_ALEN) != 0 &&
(bss = ieee80211_rx_bss_get(dev, bssid,
local->hw.conf.channel->center_freq,
ifsta->ssid, ifsta->ssid_len)))
Note:
In general disconnection is still not handled properly in mac80211
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes an issus that made "iwconfig eth1 power on" non-working.
When we get a "PS sleep" event, we have to confirm this to the firmware.
The confirm happens with a command, but this command is special: the
firmware won't send us a response. if_cs_host_to_card() is setting
priv->dnld_sent anyway, so this variable stayed at DNLD_DATA_SENT and
was never cleared back.
Now I put the special knowledge that the CMD_802_11_PS_MODE with
CMD_SUBCMD_SLEEP_CONFIRMED doesn't need to need a response by directly
clearing the dnld_sent state in lbs_send_confirmsleep().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise userspace has no idea the IBSS creation succeeded.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When another scan is in progress, a direct scan gets dropped on the
floor. However, that direct scan is usually the scan that's really
needed by userspace, and gets stomped on by all the broadcast scans the
ipw2200 driver issues internally. Make sure the direct scan happens
eventually, and as a bonus ensure that the passive scan worker is
cleaned up when appropriate.
The change of request_passive_scan form a struct work to struct
delayed_work is only to make the set_wx_scan() code a bit simpler, it's
still only used with a delay of 0 to match previous behavior.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Format string bug. Not exploitable, as this is only writable by root,
but worth fixing all the same.
Spotted-by: Ilja van Sprundel <ilja@netric.org>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] ehea: Remove dependency on MEMORY_HOTPLUG
[POWERPC] Make walk_memory_resource available with MEMORY_HOTPLUG=n
[POWERPC] Use dev_set_name in pci_64.c
[POWERPC] Fix incorrect enabling of VMX when building signal or user context
[POWERPC] boot/Makefile CONFIG_ variable fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
sh: Add -mno-fdpic to default flags.
sh: add resource of USB host for SH7723
usb: r8a66597-hcd: Add support for SH7723 USB host
sh: Fix compile error SH7763 setup code
sh: Add SH7723 SCIF support
Minor source code cleanup of page flags in mm/page_alloc.c.
Move the definition of the groups of bits to page-flags.h.
The purpose of this clean up is that the next patch will
conditionally add a page flag to the groups. Doing that
in a header file is cleaner than adding #ifdefs to the
C code.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 30f2f0eb4b ("block: do_mounts -
accept root=<non-existant partition>") extended blk_lookup_devt() to be
able to look up partitions that had not yet been registered, but in the
process made the assumption that the '&block_class.devices' list only
contains disk devices and that you can do 'dev_to_disk(dev)' on them.
That isn't actually true. The block_class device list also contains the
partitions we've discovered so far, and you can't just do a
'dev_to_disk()' on those.
So make sure to only work on devices that block/genhd.c has registered
itself, something we can test by checking the 'dev->type' member. This
makes the loop in blk_lookup_devt() match the other such loops in this
file.
[ We may want to do an alternate version that knows to handle _either_
whole-disk devices or partitions, but for now this is the minimal fix
for a series of crashes reported by Mariusz Kozlowski in
http://lkml.org/lkml/2008/5/25/25
and Ingo in
http://lkml.org/lkml/2008/6/9/39 ]
Reported-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Neil Brown <neilb@suse.de>
Cc: Joao Luis Meloni Assirati <assirati@nonada.if.usp.br>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In 2.6.26, we added some support for send with invalidate work
requests, including a device capability flag to indicate whether a
device supports such requests. However, the support was incomplete:
the completion structure was not extended with a field for the key
contained in incoming send with invalidate requests.
Full support for memory management extensions (send with invalidate,
local invalidate, fast register through a send queue, etc) is planned
for 2.6.27. Since send with invalidate is not very useful by itself,
just remove the IB_DEVICE_SEND_W_INV bit before the 2.6.26 final
release; we will add an IB_DEVICE_MEM_MGT_EXTENSIONS bit in 2.6.27,
which makes things simpler for applications, since they will not have
quite as confusing an array of fine-grained bits to check.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I think that hda_verb array must have "terminator (empty array)".
But alc262_sony_unsol[] does not have it.
And it causes gcc-4.3's buggy behavior
with snd_hda_sequence_write().
Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Presently the --fdpic specifier and the --isa matching clash when
building with FDPIC toolchains. As we have no interest in building the
kernel with --fdpic in the first place, always try to add in -mno-fdpic
to the default flags.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R8A66597 is similar to SH7723 USB 2.0 Host/Function module.
In addition, the USB of SH7366 is compatible with SH7723.
It can support SH7723 USB host by changing Kconfig.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763's setup code use old DECLARE_INTC_DESC.
There was a compile error because of this.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that walk_memory_resource() is available regardless of
MEMORY_HOTPLUG's setting, this dependency is not needed.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ehea driver was recently changed[1] to use walk_memory_resource() to
detect the system's memory layout. However, walk_memory_resource() is
available only when memory hotplug is enabled. So CONFIG_EHEA was
made to depend on MEMORY_HOTPLUG [2], but it is inappropriate for a
network driver to have such a dependency.
Make the declaration of walk_memory_resource() and its powerpc
implementation (ehea is powerpc-specific) unconditionally available.
[1] 48cfb14f8b
"ehea: Add DLPAR memory remove support"
[2] fb7b6ca2b6
"ehea: Add dependency to Kconfig"
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During the next merge window, pci_name()'s return value will become
const, so use the new dev_set_name() instead to avoid the warning (from
linux-next):
arch/powerpc/kernel/pci_64.c: In function 'of_create_pci_dev':
arch/powerpc/kernel/pci_64.c:193: warning: passing argument 1 of 'sprintf' discards qualifiers from pointer target type
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When building a signal or a ucontext, we can incorrectly set the MSR_VEC
bit of the kernel pt_regs->msr before returning to userspace if the task
-ever- used VMX.
This can lead to funny result if that stack used it in the past, then
"lost" it (ie. it wasn't enabled after a context switch for example)
and then called get_context. It can end up with VMX enabled and the
registers containing values from some other task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
