We only want to clear the run bit for this one timer, not all status bits.
So don't read the whole reg and then write all the bits back out.
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When suspending/resuming, the common task freezing code will run in
parallel and freeze processes on each core. This is because the code
uses the non-smp version of memory barriers (as well it should).
The Blackfin smp barrier logic at the moment contains the cache sync
logic, but the non-smp barriers do not. This is incorrect as Rafel
summarized:
> ...
> The existing memory barriers are SMP barriers too, but they are more
> than _just_ SMP barriers. At least that's how it is _supposed_ to be
> (eg. rmb() is supposed to be stronger than smp_rmb()).
> ...
> However, looking at the blackfin's definitions of SMP barriers I see
> that it uses extra stuff that should _also_ be used in the definitions
> of the mandatory barriers.
> ...
URL: http://lkml.org/lkml/2011/4/13/11
LKML-Reference: <BANLkTi=F-C-vwX4PGGfbkdTBw3OWL-twfg@mail.gmail.com>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When we get a port status change event, we need to figure out what type of
port it came from: a USB 3.0 port, or a USB 2.0/1.1 port. We can't know
which usb_hcd to use until that point, so hcd will be NULL for part of the
function. Unfortunately, if any of the sanity checks fail, we'll jump to
the cleanup label before hcd is set to a valid pointer, and then we'll
attempt to tell the USB core to kick the hcd, which is NULL.
Skip kicking the roothub if the sanity checks fail.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:
usb 3-4: ep 0x83 - rounding interval to 512 microframes
Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.
This should be queued for stable kernels back to 2.6.31.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
The logic of the handling Missed Service Error Events was pretty
confusing as we were checking the same condition several times.
In addition, it caused compiler warning since the compiler could
not figure out that event_trb is actually unused in case we are
skipping current TD.
Fix that by rearranging "skip" condition checks, and factor out
skip_isoc_td() so that it is called explicitly.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Remove 'inline' markings from file-local functions and let compiler
do its job and inline what makes sense for given architecture.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There were some places that compared port_speed == -1 where port_speed
is a u8. This doesn't work unless we cast the -1 to u8. Some places
did it correctly.
Instead of using -1 directly, I've created a DUPLICATE_ENTRY define
which does the cast and is more descriptive as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Macro arguments used in expressions need to be enclosed in parenthesis
to avoid unpleasant surprises.
This should be queued for kernels back to 2.6.31
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Isochronous and interrupt SuperSpeed endpoints use the same mechanisms
for decoding bInterval values as HighSpeed ones so adjust the code
accordingly.
Also bandwidth reservation for SuperSpeed matches highspeed, not
low/full speed.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the HcInterrupt register write to clear the
pending interrupt to after the isr work is done, doing this removes
glitches in the irq line.
Signed-off-by: Richard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver did not take the zero flag in the USB request. If the
request length is the same as the endpoint's maxpacket, an additional
ZLP with no data has to be transmitted.
The method used here is inspired to what is done in fsl_udc_core.c
(and pxa27x_udc.c and at91_udc.c) where this is supported.
There already was a discussion about this topic with people from
Keymile, and I propose here a better implementation:
http://thread.gmane.org/gmane.linux.usb.general/38951
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are two -ENODEV error paths in qcprobe where the allocated private
data is not freed, this patch adds the two missing kfrees to avoid
leaking memory on the error path
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the qcprobe logic such that serial->private is not set when
qcprobe exits with -ENODEV, otherwise serial->private will point to freed
memory on -ENODEV
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qcprobe function allocates serial->private but this is never freed, this
patch adds a new function qc_release() which frees serial->private, after
calling usb_wwan_release
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb serial: ftdi_sio: add two missing USB ID's for Hameg interfaces HO720
and HO730
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was an unlock missing on the error path.
Also I did a small cleanup by changing ep->dev->lock for just dev->lock.
They're the same lock, but dev->lock is shorter and that's how it is
used for the spin_unlock_irqrestore() call.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Booting latest kernel on my test machine produces a lockdep
warning from the usb_amd_find_chipset_info() function:
WARNING: at /data/lemmy/linux.trees.git/kernel/lockdep.c:2465 lockdep_trace_alloc+0x95/0xc2()
Hardware name: Snook
Modules linked in:
Pid: 959, comm: work_for_cpu Not tainted 2.6.39-rc2+ #22
Call Trace:
[<ffffffff8103c0d4>] warn_slowpath_common+0x80/0x98
[<ffffffff812387e6>] ? T.492+0x24/0x26
[<ffffffff8103c101>] warn_slowpath_null+0x15/0x17
[<ffffffff81068667>] lockdep_trace_alloc+0x95/0xc2
[<ffffffff810ed9ac>] slab_pre_alloc_hook+0x18/0x3b
[<ffffffff810ef227>] kmem_cache_alloc_trace+0x25/0xba
[<ffffffff812387e6>] T.492+0x24/0x26
[<ffffffff81238816>] pci_get_subsys+0x2e/0x73
[<ffffffff8123886c>] pci_get_device+0x11/0x13
[<ffffffff814082a9>] usb_amd_find_chipset_info+0x3f/0x18a
...
It turns out that this function calls pci_get_device under a spin_lock
with irqs disabled, but the pci_get_device function is only allowed in
preemptible context.
This patch fixes the warning by making all data-structure
modifications on temporal storage and commiting this back
into the visible structure at the end. While at it, this
patch also moves the pci_dev_put calls out of the spinlocks
because this function might sleep too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In file included from drivers/usb/host/ohci-hcd.c:1028:0:
drivers/usb/host/ohci-au1xxx.c:36:7: warning: "__BIG_ENDIAN" is not defined
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build failure introduced by commit
7acc6197b7 (usb: musb: Idle path retention
and offmode support for OMAP3) when building without gadget
support.
CC drivers/usb/musb/omap2430.o
drivers/usb/musb/omap2430.c: In function ‘musb_otg_notifications’:
drivers/usb/musb/omap2430.c:262: error: ‘struct musb’ has no member named ‘gadget_driver’
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly. This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.
The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-Tested-by: Dan Duval <dan.duval@stratus.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During processing of bunch of eem frames if "echo" command is found
skb is cloned and the cloned version should be used to send reply.
Unfortunately, the data of the original skb were actually used and
the cloned skb is never freed.
Using the cloned skb and freeing the skb in the completion callback
for usb request.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added new ProdutIds for two devices from CTI GmbH Leipzig.
Signed-off-by: Christian Simon <simon@swine.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because the disconnect function in the composite driver will call spin_lock,
this driver has to call spin_unlock before calling driver->disconnet().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable USB_ARCH_HAS_EHCI in arch Kconfig and enable it in usb Kconfig
Warning log:
warning: (MICROBLAZE) selects USB_ARCH_HAS_EHCI which has unmet
direct dependencies (USB_SUPPORT)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ep_read() acquires data->lock mutex in get_ready_ep() and releases it on
all paths except for one: when usb_endpoint_xfer_isoc() failed. The
patch adds mutex_unlock(&data->lock) at that path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format build warning and grammar typo on same line.
drivers/usb/host/isp1760-hcd.c:300: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-greg' of git://gitorious.org/usb/usb:
USB: musb: blackfin: work around anomaly 05000450
usb: musb: Fix the crash issue during reboot
usb: musb: gadget: check the correct list_head
usb: musb: temporarily make it bool
USB: musb: dereferencing an iomem pointer
USB: musb: silence printk format warning
USB: musb: using 0 instead of NULL
USB: musb: add missing unlock in cppi_interrupt()
usb: musb: ux500: copy dma mask from platform device to musb device
usb: musb: clear AUTOSET while clearing DMAENAB
In the function blk_register_queue(), var _dev_ is already assigned by
disk_to_dev().So use it directly instead of calling disk_to_dev() again.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Modified by me to delete an empty line in the same function while
in there anyway.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
While decoding a secinfo reply, I store the list of supported sec
flavors on a page accessible through res->flavors. Before reading
each new flavor, I do some math to determine if there is enough
space left on this page, and I break out of my read look if there
isn't. In order to perform this check correctly, I need to use the
address of res->flavors, rather than the address of res.
When this loop was broken early I lied to the caller and told them
that the entire list had been decoded. This could lead to problems
if the caller tries to use any the garbage data claiming to be a
valid sec flavor. I fixed this by using res->flavors->num_flavors
as a counter, incrementing it every time a sec flavor is
successfully decoded.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We were always attempting sec flavor negotiation, even if the user
told us a specific sec flavor to use. If that sec flavor fails,
we should return an error rather than continuing with sec flavor
negotiation.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
nfs4_lookup_root() is already configured to use either RPC_AUTH_UNIX
or a user specified flavor (through -o sec=<whatever>). We should
use this flavor first, and only attempt negotiation if it fails
with -EPERM.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NFS_MAX_SECFLAVORS should already take into account RPC_AUTH_UNIX
and RPC_AUTH_NULL, so we don't need to set aside extra slots
for them.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There can be an infinite loop if gss_create_upcall() is called without
the userspace program running. To prevent this, we return -EACCES if
we notice that pipe_version hasn't changed (indicating that the pipe
has not been opened).
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like
[ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit c191a836a9.
It causes known regressions for programs that expect to be able to use
SO_REUSEADDR to shutdown a socket, then successfully rebind another
socket to the same ID.
Programs such as haproxy and amavisd expect this to work.
This should fix kernel bugzilla 32832.
Signed-off-by: David S. Miller <davem@davemloft.net>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ce6120cc(ASoC: Decouple DAPM from CODECs) changed the signature of
snd_soc_dapm_widgets_new to take an pointer to a snd_soc_dapm_context instead of
a snd_soc_codec. The call to snd_soc_dapm_widgets_new in jz4740_codec_dev_probe
was not updated to reflect this change, which results in a compiletime warning
and a runtime OOPS.
Since the core code calls snd_soc_dapm_widgets_new after the codec has been
registered it can be dropped here.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
mark_inode_dirty_sync() grabs the same inode lock!
race conditions between holding the lock in pnfs_set_layoutcommit() and in
mark_inode_dirty_sync() can result in a second call to pnfs_layoutcommit_inode(), but
this will be a noop as NFS_INO_LAYOUTCOMMIT won't be set in the second call
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/avr32-2.6:
avr32: add ATAG_BOARDINFO
don't check platform_get_irq's return value against zero
avr32: init cannot ignore signals sent by force_sig_info()
avr32: fix deadlock when reading clock list in debugfs
avr32: Fix .size directive for cpu_enter_idle
avr32: At32ap: pio fix typo "))" on gpio_irq_unmask prototype
fix the wrong argument of the functions definition
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (22 commits)
Revert "i915: restore only the mode of this driver on lastclose"
Revert "ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set."
i915: select VIDEO_OUTPUT_CONTROL for ACPI_VIDEO
drm/radeon/kms: properly program vddci on evergreen+
drm/radeon/kms: add voltage type to atom set voltage function
drm/radeon/kms: fix pcie_p callbacks on btc and cayman
drm/radeon/kms: fix suspend on rv530 asics
drm/radeon/kms: clean up gart dummy page handling
drm/radeon/kms: make radeon i2c put/get bytes less noisy
drm/radeon/kms: pll tweaks for rv6xx
drm/radeon: Fix KMS legacy backlight support if CONFIG_BACKLIGHT_CLASS_DEVICE=m.
radeon: Fix KMS CP writeback on big endian machines.
i915: restore only the mode of this driver on lastclose
drm/nvc0: improve vm flush function
drm/nv50-nvc0: remove some code that doesn't belong here
drm/nv50: use "nv86" tlb flush method on everything except 0x50/0xac
drm/nouveau: quirk for XFX GT-240X-YA
drm/nv50-nvc0: work around an evo channel hang that some people see
drm/nouveau: implement init table opcode 0x5c
drm/nouveau: fix oops on unload with disabled LVDS panel
...
We really only want to unplug the pending IO when the process actually
goes to sleep. So move the test for flushing the plug up to the place
where we actually deactivate the task - where we have properly checked
for preemption and for the process really sleeping.
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
