This patch adds board specific r-standby resume code
for ms7724se.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
KEYSC::SCN register of SH7724 is 3bit.
Thus, scan_timing should be 0 - 7 here.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When FSI and Network (= NFS file system) were used at the same time,
the I/O of FSI was unstable. This patch updates the SPU2 clock (which
is used for FSI) to solve this issue. Special thanks to Jeremy.
Signed-off-by: Jeremy Baker <Jeremy.Baker@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7724 processor code to always enable vpu_clk.
On the Ecovec board, set the vpu_clk to 166 Mhz.
The 166MHz setting results in a divide-by-6 setup for
vpu_clk and improves the VPU performance compared to the
power-on-reset/bootloader configuration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7724 INTC table
and update the SDHI platform data for Ecovec24,
KFR2R09 and MS7724SE.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7723 INTC table
and update the SDHI platform data for AP325.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7722 INTC table
and update the SDHI platform data for Migo-R.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This uses the new create_irq_nr() to build up the FPGA's desired virtual
IRQ mapping and permits us to finally flip on sparseirq for this board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The irq_desc needs to be accessed with irq_to_desc(), this fixes up a
build error with irq_desc being undefined.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nothing is using this, kill it off. Fixing up access sizes can be done
with trapped I/O for anyone wanting to make use of this for devices that
need it, everything else is already pure MMIO.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The old ctrl in/out routines are non-portable and unsuitable for
cross-platform use. While drivers/sh has already been sanitized, there
is still quite a lot of code that is not. This converts the arch/sh/ bits
over, which permits us to flag the routines as deprecated whilst still
building with -Werror for the architecture code, and to ensure that
future users are not added.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements dynamic probing for the system FPGA. The system reset
controller contains a fixed magic read word in order to identify the
FPGA. This just utilizes a simple loop that scans across all of the fixed
physical areas (area 0 through area 6) to locate the FPGA.
The FPGA also contains register information detailing the area mappings
and chip select settings for all of the other blocks, so this needs to be
done before we can set up anything else.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves out the FPGA IRQ controller setup code to its own file, in
preparation for switching off of IRL mode and having it provide its own
irq_chip.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of refactoring of the FPGA management code. The primary
FPGA initialization is moved out to its own file in preparation for
implementing some of the more complex capabilities, a complete set of
register definitions is provided, and all of the existing users in the
board code are moved over to use the new interface instead of setting up
overlapping mappings. This also corrects the FPGA size, which previously
was chomped off at the SDIF control register.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This uses the mode pins exposed through the FPGA to work out whether
we're driven from EXTAL or not and does the appropriate setup and
propagation through the clock framework.
This will also -EINVAL out for anyone adding in their own oscillators,
forcing proper configuration with the clock framework instead of
proceeding on with bogus clock values.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently 'flags' gets passed around a lot between the various ioremap
helpers and implementations, which is only 32-bits. In the X2TLB case
we use 64-bit pgprots which presently results in the upper 32bits being
chopped off (which handily include our read/write/exec permissions).
As such, we convert everything internally to using pgprot_t directly and
simply convert over with pgprot_val() where needed. With this in place,
transparent fixmap utilization for early ioremap works as expected.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the cpu_relax() to a udelay(1), which fixes up issues with
the EEPROM polling occasionally timing out.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need to write to the DRAM config register very early and at such an
early stage ioremap() is not available. So use ioremap_fixed() to map
the register.
The reason that we are avoiding using the legacy P2 mapping is that
there will come a day when the legacy P2 mappings no longer exist.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Previously this was only built in for Urquell boards, but the same
approach can be used on SDK7786 now that the mode pin reading is
supported, so make it generic to SH7786.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This wires up the mode pins support on the SDK7786. The pins are
standard SH7786 pins, and all are fixed in software. Needed for the
clock framework, PCIe, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This updates the existing boards that specify the register width through
platform data to use the resource flags instead. This eliminates platform
data completely in most cases, and permits further improvement in the
heartbeat driver as well as shrinking the overall private data size.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the lis3lv02d motion sensor connected via
i2c on the Ecovec board. Tested with evtest.
Signed-off-by: NISHIMOTO Hiroki <nishimoto.hiroki@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This stubs in some preliminary board support for the RTE SDK7786.
This is quite stunted at the moment, and primarily builds on top of the
system FPGA. FPGA IRQs are handled via CPU IRL masking for simplicity,
with initial peripheral support restricted to the debug ethernet.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This gets rid of the arbitrary set of vectors used by the SE7722 FPGA
interrupt controller and switches over to a completely dynamic set.
No assumptions regarding a contiguous range are made, and the platform
resources themselves need to be filled in lazily.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
o remove unused define
o add device name comment
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
sh: Fix test of unsigned in se7722_irq_demux()
sh: mach-ecovec24: Add FSI sound support
sh: mach-ecovec24: Add mt9t112 camera support
sh: mach-ecovec24: Add tw9910 support
sh: MSIOF/mmc_spi platform data for the Ecovec24 board
sh: ms7724se: Add ak4642 support
sh: Fix up FPU build for SH5
sh: Remove old early serial console code V2
sh: sh5 scif pdata (sh5-101/sh5-103)
sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
sh: sh2 scif pdata (sh7616)
sh-sci: Extend sh-sci driver with early console V2
sh: Stub in P3 ioremap support for nommu parts.
sh: wire up vmallocinfo support in ioremap() implementations.
sh: Make the unaligned trap handler always obey notification levels.
sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
...
It has been experimentally found out, that the sensor only supports up to
512x384 video output and also has some restrictions on minimum scale. We
disable non-working size ranges until, maybe, someone finds out how to properly
set them up. Also add cropping support, an auto white balance control, platform
data to specify master clock frequency and polarity of the IOCTL pin.
create mode 100644 include/media/rj54n1cb0c.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all soc-camera drivers to the new mediabus
API. This also takes soc-camera client drivers one step closer to also be
usable with generic v4l2-subdev host drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After this change drivers can be further extended to not fail, if they don't
get platform data, but to use defaults.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
se7722_fpga_irq[] is unsigned so the test does not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MSIOF and mmc_spi platform data for
the CN11 port on the SuperH Ecovec24 board. No card
detect interrupt is available so the MMC code is
configured to poll. The WP signal is implemented
together with CD and power control. The board only
supports 3.3V power.
The platform data is wrapped in SDHI #ifdefs to
allow both the SDHI and the MSIOF to coexist. Only
one configuration is allowed at a time. The pin
routing is selected by a dip switch but we can
unfortunately not detect this setting at run time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
Current soc-camera needs SOCAM_DATA_ACTIVE_xxx flags for use.
We can not open old ncm03j camera device without this patch.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a ->start_transfer() callback to the
KFR2R09 lcd handling code. The callback is used to
notify the lcd controller that a new frame of data
is about to be transferred. The callback is only used
in combination with deferred io, but the code has
been tested both with and without deferred io enabled.
Without this patch the display data on the KFR2R09
lcd panel becomes corrupted over time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
