Commit Graph

210 Commits

Author SHA1 Message Date
Bruce Allan
818f33313c e1000e: do not initiate autonegotiation during OEM configuration
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:32 -08:00
Bruce Allan
189983d469 e1000e: remove unnecessary 82577 workaround causing link issues
A workaround for pre-release versions of 82577 is causing link issues on
some switches.  The workaround is no longer needed on production parts so
remove it.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:29 -08:00
Bruce Allan
610c992884 e1000e: flow control thresholds not correct when changing mtu
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:27 -08:00
Bruce Allan
4c86e0b945 e1000e: add Tx timeout factor for 100Mbps
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:26 -08:00
Bruce Allan
29afd69063 e1000e: set flow control thresholds properly after enabling/disabling pause
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:24 -08:00
Bruce Allan
842ec8b64a e1000e: read of PHY register may access wrong page on 82578
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page.  Also error out if the page select operation
fails.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:22 -08:00
Bruce Allan
38eb394e33 e1000e: partial revert of 3ec2a2b8 plus FC workraround for 82577/8
Commit 3ec2a2b80f broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:20 -08:00
Bruce Allan
1d5846b921 e1000e: rework disable K1 at 1000Mbps for 82577/82578
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets.  Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected.  The original version of this
workaround was found to be incomplete.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-29 22:48:39 -07:00
Bruce Allan
f523d2114e e1000e: config PHY via software after resets
On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an
issue with the hardware automatically configuring the PHY with contents
from the EEPROM after the PHY is reset, so do the configuration by the
driver instead.  This was already similarly done for some 82566 parts in
e1000_phy_hw_reset_ich8lan() but needs to be done after other resets,
so move the PHY configuration code to its own function and call after
all PHY resets.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-29 22:48:37 -07:00
Bruce Allan
5ccdcecb72 e1000e: allow for swflag to be held over consecutive PHY accesses
PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch).  This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired.  The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.

The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-26 16:16:25 -07:00
Bruce Allan
ca15df58b1 e1000e: separate mutex usage between NVM and PHY/CSR register for ICHx/PCH
Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed.  However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-26 16:16:24 -07:00
Bruce Allan
fa2ce13ca7 e1000e: 82577/82578 requires a different method to configure LPLU
Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-26 16:16:23 -07:00
Bruce Allan
53ac5a8875 e1000e: increase swflag acquisition timeout for ICHx/PCH
In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers).  This could cause PHY registers to not get
configured properly resulting in link issues.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-26 16:16:19 -07:00
Bruce Allan
db2932ecf8 e1000e: clear PHY wakeup bit after LCD reset on 82577/82578
Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset.  If this bit remains set, link
problems may occur.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-26 16:16:18 -07:00
Bruce Allan
74eee2e8d0 e1000e: reset the PHY on 82577/82578 when going to Sx
The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect.  Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-22 21:22:18 -07:00
Alexander Duyck
a825e00c98 e1000e: swap max hw supported frame size between 82574 and 82583
There appears to have been a mixup in the max supported jumbo frame size
between 82574 and 82583 which ended up disabling jumbo frames on the 82574
as a result.  This patch swaps the two so that this issue is resolved.

This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=14261

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-04 21:08:49 -07:00
Frans Pop
19d5afd4f0 e1000e/igb/ixgbe: Don't report an error if devices don't support AER
The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.

Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-02 10:04:12 -07:00
Ben Hutchings
7ab0f2736b netdev: Remove redundant checks for CAP_NET_ADMIN in MDIO implementations
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-03 20:02:11 -07:00
David S. Miller
6cdee2f96a Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/yellowfin.c
2009-09-02 00:32:56 -07:00
Stephen Hemminger
3b29a56d31 intel: convert drivers to netdev_tx_t
Get rid of some bogus return wrapping as well.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:13:52 -07:00
Xiaotian Feng
68eac4602b e1000e: fix use of pci_enable_pcie_error_reporting
commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer
support for e1000e, but it is not reasonable to disable it in
e1000_remove but enable it in e1000_resume.  This patch enables aer
support in e1000_probe.

Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-15 18:52:59 -07:00
Bruce Allan
82776a4bcd e1000e: WoL does not work on 82577/82578 with manageability enabled
With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get
configured on newer parts which use PHY wakeup vs. MAC wakeup which causes
WoL to not work.  The driver should configure PHY wakeup whether or not
manageability is enabled.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-15 18:52:58 -07:00
Bruce Allan
148675a7b2 e1000e: fix potential NVM corruption on ICH9 with 8K bank size
The bank offset was being incorrectly calculated on ICH9 parts with a bank
size of 8K (instead of the more common 4K bank) which would cause any NVM
writes to be done on the wrong address after switching from bank 1 to bank
0.  Additionally, assume we are meant to use bank 0 if a valid bank is not
detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore
when writing to the shadow ram version of the NVM image.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-09 21:45:38 -07:00
Bruce Allan
373a88d78b e1000e: fix acquisition of SW/FW/HW semaphore for ICHx parts
For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to
acquire the SW/FW/HW semaphore instead of multiple times to prevent the
hardware from having problems (especially for systems with manageability
enabled), and extend the timeout for the hardware to set the SWFLAG bit.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-09 21:45:36 -07:00
Bruce Allan
7d3cabbcc8 e1000e: disable K1 at 1000Mbps for 82577/82578
This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets.  Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:42 -07:00
Bruce Allan
906e8d9792 e1000e: delay second read of PHY_STATUS register on failure of first read
Some PHYs may require two reads of the PHY_STATUS register to determine the
link status.  If the PHY is being accessed by another thread it is possible
the first read could timeout and fail.  In this case, put a delay in so
the second read will pick up the correct link status.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:39 -07:00
Bruce Allan
28c9195a57 e1000e: prevent NVM corruption on sectors larger than 4K
Limit NVM writes to 4K sections to prevent NVM corruption on larger
sector allocations (up to 64K).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:35 -07:00
Bruce Allan
60f1292fcb e1000e: do not write SmartSpeed register bits on parts without support
The driver was accessing register bits for features on parts that do
not support that feature.  This could cause problems in the hardware.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:32 -07:00
Bruce Allan
fc0c7760ae e1000e: delay after LCD reset and proper checks for PHY configuration done
A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently.  Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing.  Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:29 -07:00
Bruce Allan
e65fa87c22 e1000e: PHY loopback broken on 82578
PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround.  Don't perform the
workaround if in PHY loopback mode.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:27 -07:00
Mike Mason
c93b5a76d5 e1000e: io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT
on permanent failure

PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is not
checked in many of the network drivers.

This patch fixes the omission in the e1000e driver.

Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:47:02 -07:00
Andy Gospodarek
679e8a0f0a e1000e: stop unnecessary polling when using msi-x
The last hunk of this commit:

    commit 12d04a3c12
    Author: Alexander Duyck <alexander.h.duyck@intel.com>
    Date:   Wed Mar 25 22:05:03 2009 +0000

        e1000e: commonize tx cleanup routine to match e1000 & igb

changed the logic for determining if we should call napi_complete or
not at then end of a napi poll.

If the NIC is using MSI-X with no work to do in ->poll, net_rx_action
can just spin indefinitely on older kernels and for 2 jiffies on newer
kernels since napi_complete is never called and budget isn't
decremented.

Discovered and verified while testing driver backport to an older
kernel.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-19 01:12:51 -07:00
David S. Miller
9cbc1cb8cd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/scsi/fcoe/fcoe.c
	net/core/drop_monitor.c
	net/core/net-traces.c
2009-06-15 03:02:23 -07:00
Martin Olsson
98a1708de1 trivial: fix typos s/paramter/parameter/ and s/excute/execute/ in documentation and source comments.
Signed-off-by: Martin Olsson <martin@minimum.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-06-12 18:01:46 +02:00
Chaitanya Lala
18760f1e74 e1000e: Expose MDI-X status via ethtool change
Ethtool is a standard way of getting information about
ethernet interfaces.  We enhance ethtool kernel interface
& e1000e to make the MDI-X status readable via ethtool in
userspace.

Signed-off-by: Chaitanya Lala <clala@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-09 05:25:36 -07:00
Simon Horman
edfea6e641 e1000e: Call e1000e_config_collision_dist() after TCTL has been set
e1000e_config_collision_dist() sets tctl, but subsequently tctl is
overwritten.  It seems to me that as things stand the call to
e1000e_config_collision_dist() has no effect and should either be
removed or moved down a little bit.  This kernel patch takes the latter
option.

Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-09 05:25:36 -07:00
Dave Graham
23a2d1b233 e1000e: Fixes possible phy corrupton on 82571 designs.
Phy corruption has been observed on 2-port 82571 adapters, and is root-caused
to lack of synchronization between the 2 driver instances, which conflict
when attempting to access the phy via the single MDIC register.
A semaphore exists for this purpose, and is now used on these designs. Because
PXE &/or EFI boot code (which we cannot expect to be built with this fix) may
leave the inter-instance semaphore in an invalid initial state when the driver
first loads, this fix also includes a one-time (per driver load) fix-up of the
semaphore initial state.

Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-09 05:25:35 -07:00
Eric Dumazet
042a53a9e4 net: skb_shared_info optimization
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.

One to access nr_frags, one to access dma_maps[0]

Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.

Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08 00:21:48 -07:00
Bruce Allan
3be8c940a6 e1000e: bump the version number
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:46:37 -07:00
Bruce Allan
37289d9c1e e1000e: workaround a Tx hang on 82577/82578
With bi-directional stress traffic, the receiver could hang causing the
hardware to stop and a "Detected Tx Unit Hang" message dumped to the system
logfile.  Temporarily workaround this issue by disabling Tx flow control by
default.  The issue is currently being investigated and a follow-on patch
will be provided to revert this when it is resolved.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:46:36 -07:00
Bruce Allan
a4f58f5455 e1000e: add support for 82577/82578 GbE LOM parts
This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters.  These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions).  New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:46:34 -07:00
Bruce Allan
2adc55c959 e1000e: specify max supported frame size in adapter struct
By putting the maximum frame size supported by the hardware into the
adapter structure, the change_mtu entry point function can be cleaned
up of checks for all the different max frame sizes supported by

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:46:33 -07:00
Bruce Allan
3ec2a2b80f e1000e: correct flow control thresholds
The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:46:33 -07:00
Bruce Allan
918d7197aa e1000e: do not attempt to disable smart powerdown if not supported
During reset, the driver was attempting to disable the Smart Powerdown
feature even if the part does not support Smart Powerdown.  Check for
support before attempting to disable the feature.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:46:32 -07:00
Bruce Allan
6e50912a44 e1000e: enable CRC stripping by default
CRC stripping should be enabled by default but was not if it was not
specified as a module parameter.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:46:31 -07:00
Eric Dumazet
cdd0db058d net: dont update dev->trans_start
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29 01:46:27 -07:00
Alexander Duyck
cbe7a81a73 igb/e1000e: update PSSR_MDIX value to reflect correct bit
The phy port status register has the MDI-X status bit on bit 11, not bit 3
as is currently setup in the define.  This patch corrects that so the
correct bit is checked on igp PHY types.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-26 20:35:06 -07:00
Jesse Brandeburg
c2d5ab4973 e1000/e1000e/igb/ixgb: don't txhang after link down
after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down.  Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.

Don't bother arming to tx hang detection when link is down.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-07 14:52:32 -07:00
Jesse Brandeburg
4cb9be7ab4 e1000/e1000e/igb/ixgb: do not use netif_wake_queue un-necessarily
It was pointed out that the Intel wired ethernet drivers do not need to
wake the tx queue since netif_carrier_on/off will take care of the qdisc
management in order to guarantee the correct handling of the transmit
routine enable state.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-22 00:47:54 -07:00
David S. Miller
e5e9743bb7 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/core/dev.c
2009-04-21 01:32:26 -07:00