Add a flag to indicate we initiated a recovery work
on purpose, in order to avoid triggering BUG() (when
the bug_on_recovery module param was set).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We didn't update the beacon interval on association
(or on a change notification when working as sta),
so the default interval (100ms) was always used.
Update the beacon interval according to the bss_conf
before starting the sta role (on association).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
return EBUSY on scan when there is any role
in ROC (not necessarily the one we are going
to use)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently, CHANGE_CHANNEL indication while
associated is considered as roaming attempt.
However, with the new auth/assoc redesign,
we no longer have to handle this case,
so remove it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In some cases, the wrong vif type was set in the
change_interface callback (P2P_CLIENT/P2P_GO instead
of STA/AP)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The sesssion_counter has to be incremented each time
the dev is started (similar to sta role).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx currently looks for AP authorization by registering
a netdev notifier and waiting for the IF_OPER_UP notification,
which is quite cumbersome.
Use the newly introduced sta_state callback (waiting
for assoc -> auth notification) instead, in order to
simplify it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement sta_state callback instead of the
sta_add/remove callbacks.
Update the fw regarding peer state and ht caps
only after the station was authorized. Otherwise,
the fw might try establishing BA session before
the sta is authorized.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On disassociation, check only whether the current vif
is idle, instead of checking whether the device is idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
device role is used for scanning and sending packets
before connection. however, since we don't need to
send packets before ibss creation, there is no need
to start the device on idle-off.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The commit "ath6kl: Use a mutex_lock to avoid
race in diabling and handling irq" introduces a
state where ath6kl_sdio_irq_handler() would be waiting
to claim the sdio function for receive indefinitely
when things happen in the following order.
ath6kl_sdio_irq_handler()
- aquires mtx_irq
- sdio_release_host()
ath6kl_sdio_irq_disable()
- sdio_claim_host()
- sleep on mtx_irq
ath6kl_hif_intr_bh_handler()
- (indefinitely) wait for the sdio
function to be released to exclusively claim
it again for receive operation.
Fix this by replacing the mtx_irq with an atomic
variable and a wait_queue.
kvalo: add ath6kl_sdio_is_on_irq() due to open parenthesis alignment
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Collect residue firmware logs following firmware assert.
Firmware sends logs to host once the 1500 byte log buffer
has been filled. At time of assert, there could be residue
logs lying in the firmware. This patch pulls those residue
logs. This would give the full picture of the firmware.
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
firmware debug utility expects firmware log record size
to be 1500 bytes. This patch ensures that the
firmware record will be exactly 1500 bytes.
kvalo: remove trailing space
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl FW does not distinguish between different types of hidden
SSIDs (empty or null), so treat all cfg80211 requests for hidden ssid
the same.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove check so that IE in firmware is cleared if not set. Without this fix, any
previously set IE will be used incorrectly in the next frame. For example,
consider the scenario where a P2P device scan is followed by a regular station
scan. The P2P IE set by the P2P scan needs to be cleared, otherwise the station
scan will contain the P2P IE.
kvalo: indentation fixes
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As regulatory events are processed even before the wiphy is registered,
calling regulatory_hint() at early stage should be fixed.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes the wiphy and initial netdev registration the last step
in dev initialization. Apart from the fact that this looks right,
it can also be used to setup wiphy with the regulatory information
received from firmware after uploading the firmware. Also it fixes
a FIXME in ath6kl_core_init() where mac address is copied into
netdev->dev_addr, ath6kl_interface_add() takes care of this as well.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the wmi event is vif specific, the validation of vif index
is taken care in ath6kl_wmi_proc_events_iface(). This also avoids
the need for a netdev to be registered while receiving initial events
like "target_ready" and "regulatory domain".
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the wmi event processing into the one which needs to be
vif specific and the reset. This is a step towards avoiding
the need for wiphy and a netdev registration before getting
any message from firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move netdev->hw_features setting from ath6kl_core_init() to
init_netdev() so that it is done for every interface.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are some code which initializes various wiphy members
left outside ath6kl_cfg80211_init(), in ath6kl_core_init().
Move them into a single palce.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
That commit intended for 3.4 renamed IEEE80211_TX_CTL_POLL_RESPONSE as
IEEE80211_TX_CTL_NO_PS_BUFFER. Meanwhile, "carl9170: fix frame delivery
if sta is in powersave mode" added a reference to
IEEE80211_TX_CTL_POLL_RESPONSE in the fixes stream for 3.3. This simple
patch fixes that merge boo-boo.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous RX error checking was done exclusive-or for different error
types and caused DFS pulse events to be dropped when other error
flags (e.g. CRC) were set simultaneously.
This patch decouples PHY error processing from other types and ensures
that all pulses detected by HW are accounted by the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the enum il_calib. It defined one identifier: IL_CALIB_MAX.
Remove the function il4965_calib_free_results. It was doing nothing
because IL_CALIB_MAX is zero. Next, remove calib_results from the
il_priv structure and also remove the associated return
type/struct il_calib_result.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the menuconfig system doesn't indent the debug options
for the 3945 /4965, add some text to make it clear which
debug options are being configured.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of defining an 'enum', we can simply use 'u8' flag for WEP
status. Rename 'wep_status' to 'wep_enabled' to match with
'wpa_enabled' and 'wpa2_enabled'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It should have been removed by commit "mwifiex: use cfg80211 dynamic
scan..." (7c6fa2a843..) after adding code to avoid an extra scan
during association because scan entries are valid for 15 seconds in
cfg80211 stack.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The association sequence looks (roughly) like
this now:
* set BSSID
* set station to EXIST state
* send auth
* set station to AUTH state
* send assoc
* set station to ASSOC state
* set BSS info to associated
In contrast, the deauth/disassoc sequence is
the other way around:
* clear BSSID/BSS info state
* remove station
* send deauth/disassoc
(in some cases the last two steps are reversed.)
This patch encodes the entire sequence in the
ieee80211_set_disassoc() function and changes
it to be like this, for good measure with an
explicit flush:
* send deauth/disassoc
* flush
* remove station
* clear BSSID/BSS info state
At least iwlwifi gets confused with the other
sequence in P2P mode and complains that it
wasn't able to flush the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_set_disassoc() is called with the
tx argument set to true, it will send DelBA out
to the peer. This isn't useful or necessary in a
few cases where we do it today, those being when
we lost the connection or when the supplicant
explicitly asked us to not tell the AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc()
pass out the frame and call it from the caller. That saves the
SKB allocation if we don't actually want to send the frame and
enables us to make the ordering smarter in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I am running Debian testing kernel 3.1.0-1-amd64, using a 079b:0062 Sagem
XG-76NA 802.11bg stick.
Upon zd1211rw interface
bringup (ifconfig wlan0 up) I get the following timeout:
[ 950.330573] zd1211rw 1-3:1.0: phy2
[ 955.108510] zd1211rw 1-3:1.0: firmware version 4725
[ 955.148532] zd1211rw 1-3:1.0: zd1211b chip 079b:0062 v4810 high 00-19-70
AL2230_RF pa0 g--NS
[snip]
[ 955.204072] zd1211rw 1-3:1.0: error ioread32(CR_REG1): -110
A second ifconfig wlan0 up brings the interface up without problems.
After a bit more debugging, the call trace is the following:
[10241.028130] zd1211rw 1-3:1.0: zd_chip_lock_phy_regs: error
ioread32(CR_REG1): -110
[10241.028140] zd1211rw 1-3:1.0: zd_switch_radio_on: failed to lock PHY regs
[10241.028148] zd1211rw 1-3:1.0: zd_op_start: failed to set radio on
Adding a 10 milliseconds delay between the call to set_mc_hash() and
zd_chip_switch_radio_on() allows successful interface bringups in all
cases and matches what the vendor driver did.
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commit
"mwifiex: clear previous security setting during association"
fixes association failure problems observed in some corner cases
by clearing previous security setting before each association.
We should reset encryption mode flag as well. This patch takes care
of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nicolas Cavallari discovered that carl9170 has some
serious problems delivering data to sleeping stations.
It turns out that the driver was not honoring two
important flags (IEEE80211_TX_CTL_POLL_RESPONSE and
IEEE80211_TX_CTL_CLEAR_PS_FILT) which are set on
frames that should be sent although the receiving
station is still in powersave mode.
Cc: stable <stable@vger.kernel.org>
Reported-by: Nicolas Cavallari <Nicolas.Cavallari@lri.fr>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Access Point mode, when transmitting a packet, if the destination
station is in powersave mode, we abort transmitting the packet to the
device queue, but we do not reclaim the allocated memory. Given enough
packets, we can go in a state where there is no packet on the device
queue, but we think the device has no memory left, so no packet gets
transmitted, connections breaks and the AP stops working.
This undo the allocation done in the TX path when the station is in
power-save mode.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures the user won't encounter lag associated with getting in and
out of PSM when the card is in use.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Flush our Tx queues before suspending or changing the channel due to a
channel_switch element in the AP beacon.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Ensure our queues are empty at the end of a tx_flush(), in case we
timeout on passively waiting for them. This makes sure no left-overs are
transmitted when we are on the wrong channel.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Re-factor the Tx scheduler so that the system_hlid is taken into account
before restarting an iteration over the wlvifs. Previously this
hlid had a lower priority and would starve if some wlvif had many
packets.
In addition avoid iterating over wlvifs past last_wlvif when performing
the a second pass. If we had packets in those wlvifs they would have
been found earlier.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Before, the link was first freed (invalidating it in the map), and later
on vif removal, all valid wlvif-related links were reset. Since these
links were already invalid, we failed to reset them.
The bug was made worse by op_stop, which set the tx_queue_count to 0
arbitrarily. This resulted in a negative tx_queue_count in some scenarios.
Fix this by resetting the Tx-queues of a link when freeing it. Add a
WARN_ON and reset all link Tx-queues in op_stop, to avoid a negative
tx_queue_count.
[changed WARN_ON to WARN_ON_ONCE -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
These bits are used in op_tx to determine if a packet should be dropped.
As such we should use the spin lock to sync the state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
With PSM handled in FW, the checks in wl1271_elp_work() are always true.
Thus during active traffic we constantly enter and exit ELP (many times
per second). As each ELP exit takes ~10ms, this can have an adverse
effect on throughput and interactivity.
Set the ELP timeout to the dyn-ps timeout. This period is longer and
avoids the above problem. It also makes sense to stay out of ELP while
we are awake on the network, to minimize delays in Tx/Rx. The same thing
was done by the mac80211 dynamic-ps mechanism before the FW DPS changes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Register driver's ht capabilities in wiphy to avoid failures
in setting ht channels from hostapd.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Without this change, SDIO shuts down due to CRC error during
data communication to the firmware in some of the platform.
for example, scan request issued to the firmware doesn't
return scan completed events and cause the socket interface
to always return -16 (device busy).
SDIO pad drive strength should be reduced for hw2.1.1 board
to avoid such errors.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
