Blackfin already sets proper flow handlers on all IRQs, and we don't rely
on __do_IRQ, therefore we can simply select GENERIC_HARDIRQS_NO__DO_IRQ.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The simple-gpio has been replaced by the gpio sysfs interface, so drop the
unused simple-gpio resources from all Blackfin boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The patch added a special get_unmapped_area for framebuffer which
was hooked to the file ops in drivers/video/fbmem.c.
This is needed since v2.6.29-rc1 where nommu vma management was
updated, and mmap of framebuffer caused kernel BUG panic. You may turn
on "Debug the global anon/private NOMMU mapping region tree" config to
such message.
As Documentation/nommu-mmap.txt said,
"To provide shareable character device support, a driver must provide
a file->f_op->get_unmapped_area() operation. The mmap() routines will
call this to get a proposed address for the mapping."
With this change, user space should call mmap for framebuffer using
shared map. Or it can try shared map first, then private map if
failed. This shared map usage is now consistent between mmu and nommu.
The sys_ file may not be a good place for this patch. But there is a
similar one for sparc. I tested a similar patch on nios2nommu, though
I don't have a blackfin board to test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix the following 'make includecheck' warning:
arch/blackfin/mach-bf548/boards/ezkit.c: linux/input.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Structs get initialized to 0 already, and we want to punt this field, so
scrub it from all of our boards.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the common jedec_probe supports the ST PSD4256G6V, no need to
use the custom stm_flash driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the driver has been updated, convert the board resources to the
new i2c framework for managing slaves.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
conflict in radeon since new init path merged with vga arb code.
Conflicts:
drivers/gpu/drm/radeon/radeon.h
drivers/gpu/drm/radeon/radeon_asic.h
drivers/gpu/drm/radeon/radeon_device.c
Just using the tr->buffer for the API to trace_buffer_lock_reserve
is not good enough. This is because the tr->buffer may change, and we
do not want to commit with a different buffer that we reserved from.
This patch uses a local variable to hold the buffer that was used to
reserve and commit with.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
fix warnings that caused the API change of trace_buffer_lock_reserve()
change files: kernel/trace/trace_hw_branch.c
kernel/trace/trace_branch.c
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
LKML-Reference: <20091008012146.GA4170@helight>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
There is no need to assign vb before you know that space is available.
[agd5f: adapted for kernel tree.]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For AGP to work unmapped access must cover VRAM & AGP as
AGP is treated like VRAM by the GPU (ie physical address).
This patch properly setup the virtual memory system aperture
to cover AGP if AGP is enabled. It seems that there is memory
corruption after resume when using AGP (RV770 seems unaffected
thought). Version 2 just fix merge issue with updated AGP
fallback patch.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When GPU acceleration is not working with AGP try to fallback to non
AGP GART (either PCI or PCIE GART). This should make KMS failure on
AGP less painfull. We still need to find out what is wrong when AGP
fails but at least user have a lot of more chances to get a working
configuration with acceleration. This patch also cleanup R600/RV770
fallback path so they use same code as others asics. Version 2
factorize agp disabling logic to avoid code duplication and bugs.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bad generated header file leaded to use wrong register
to check IRQ status and acknowledge them. Fix the header
and use proper registers.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch allows a local IPv6 address to be resolved by rdma_cm.
To reproduce the problem:
$ rping -s -v -a ::0 &
$ rping -c -v -a <IPv6 address local to this system>
rdma_resolve_addr error -1
Local IPv6 address was obtained with "ip addr show ib0"
Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=1759
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
in_dev_get() can return NULL. If it does, iwch_query_port() will crash.
Handle the NULL case by mapping it to port state INIT.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add the file pattern of drivers/ieee1394/init_ohci1394_dma.c's
documentation to the maintainers database. init_ohci1394_dma.c is not
really part of the IEEE 1394 subsystem, but this maintainers contact
seems to be better than none at all.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In commit cb58160e ("RDMA/iwcm: Reject the connection when the cm_id
is destroyed") a call to the provider's reject handler was added to
destroy_cm_id() to fix a provider endpoint leak. This call needs to
be done with interrupts enabled. So unlock and relock around this
call. This is safe because:
1) the provider will do nothing with this endpoint until the iwcm either
accepts or rejects.
2) the lock is only released after the iwcm state is changed, so an
errant iwcm app that is destroying -and- rejecting the connection
concurrently will get a failure on one of the calls.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to legacy code from back when the dynamic tracer used a daemon,
only core kernel code was checking for failures. This is no longer
the case. We must check for failures any time we perform text modifications.
Cc: stable@kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The DMA-API debugging facility complains about b43 mapping memory from
stack for SDIO-based cards.
Indeed, b43 currently allocates the PIO RX/TX header and tail buffers
from stack. The solution here is to use heap-allocated buffers instead.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In Bugzilla No. 14181, a PowerMac G4 crashes on ifdown or
module unload because the rfkill polling has not been stopped.
For the x86 architectures, the attempt to reach a now unmapped
register is not fatal as it is on PPC.
(Includes "b43: Fix locking problem when stopping rfkill polling". -- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return type of abs() was recently changed from int to long. With
min()'s type checking we thus need to make sure that values of the same
type are compared.
This fixes:
CC [M] drivers/net/wireless/iwlwifi/iwl-5000.o
drivers/net/wireless/iwlwifi/iwl-5000.c: In function ‘iwl5000_gain_computation’:
drivers/net/wireless/iwlwifi/iwl-5000.c:320: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes following on big endian systems:
CC [M] drivers/net/wireless/iwlwifi/iwl-rx.o
drivers/net/wireless/iwlwifi/iwl-rx.c: In function ‘iwl_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-rx.c:1029: warning: integer overflow in
expression
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The address stored in the next link address is a word address but when
reading the OTP blocks, a byte address is used. Also if the blocks are
full and the last link pointer is not zero, then none of the blocks are
valid so return an error.
The algorithm is simply valid blocks have a next address and that
address's contents is zero.
Using the wrong address for the next link address gets arbitrary data,
obviously. In cases seen, the first block is considered valid when it is not.
If the block has in fact been invalidated there may be old data or
there may be no data, bad data, or partial data, there is no way of
telling. Without this patch it is possible that a device with valid OTP data
is unable to work.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving data frames, we can send them only to
the interface they belong to based on transmitting
station (this doesn't work for probe requests). Also,
don't try to handle other frames for AP_VLAN at all
since those interface should only receive data.
Additionally, the transmit side must check that the
station we're sending a frame to is actually on the
interface we're transmitting on, and not transmit
packets to functions that live on other interfaces,
so validate that as well.
Another bug fix is needed in sta_info.c where in the
VLAN case when adding/removing stations we overwrite
the sdata variable we still need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use struct wldev after detach. This fixes an oops on access.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the module is about the unload we release its call records.
The ftrace_release function was given wrong values representing
the module core boundaries, thus not releasing its call records.
Plus making ftrace_release function module specific.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
LKML-Reference: <1254934835-363-3-git-send-email-jolsa@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Saves 16 bytes of text, woohoo. But the more important point is
that it makes the code more readable when returning bool for 0/1
cases.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
CFQ enables idle only for processes that think less than the allowed
idle time. Since idle time is lower for seeky queues, we should use the
correct value in the comparison.
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.
The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Reported-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Found one system:
[ 71.120590] pci 0000:40:05.0: scanning behind bridge, config 4f4a40, pass 0
[ 71.138283] PCI: Scanning bus 0000:4a
[ 71.140341] pci 0000:4a:00.0: found [15b3:6278] class 000c06 header type 00
[ 71.157173] pci 0000:4a:00.0: reg 10 64bit mmio: [0x000000-0x0fffff]
[ 71.161697] pci 0000:4a:00.0: reg 18 64bit mmio pref: [0x000000-0x7fffff]
[ 71.179403] pci 0000:4a:00.0: reg 20 64bit mmio pref: [0x000000-0xfffffff]
[ 71.185366] pci 0000:4a:00.0: calling quirk_resource_alignment+0x0/0x1dd
[ 71.200846] pci 0000:4a:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 71.219623] PCI: Fixups for bus 0000:4a
[ 71.222194] pci 0000:40:05.0: bridge 32bit mmio: [0xcf000000-0xcf0fffff]
[ 71.238662] pci 0000:40:05.0: bridge 64bit mmio pref: [0xcd800000-0xcdffffff]
[ 71.255793] PCI: Bus scan for 0000:4a returning with max=4a
Device needs a big pref mmio, but BIOS doesn't allocate mmio to it aside
from a small MMIO range. Later, the kernel will not allocate resources to
that to the device:
[ 99.574030] pci 0000:4a:00.0: BAR 4: can't allocate mem resource [0xd0000000-0xcdffffff]
[ 99.580102] pci 0000:4a:00.0: BAR 2: got res [0xcd800000-0xcdffffff] bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.602307] pci 0000:4a:00.0: BAR 2: moved to bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.615991] pci 0000:4a:00.0: BAR 0: got res [0xcf000000-0xcf0fffff] bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.634499] pci 0000:4a:00.0: BAR 0: moved to bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.654318] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.658766] pci 0000:40:05.0: IO window: disabled
[ 99.675478] pci 0000:40:05.0: MEM window: 0xcf000000-0xcf0fffff
[ 99.681663] pci 0000:40:05.0: PREFETCH window: 0x000000cd800000-0x000000cdffffff
So try to get a big range in the pci bridge if there is no child using
that range. With the patch we get:
[ 99.104525] pci 0000:4a:00.0: BAR 4: got res [0xfc080000000-0xfc08fffffff] bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.123624] pci 0000:4a:00.0: BAR 4: moved to bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.131977] pci 0000:4a:00.0: BAR 2: got res [0xfc090000000-0xfc0907fffff] bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.149788] pci 0000:4a:00.0: BAR 2: moved to bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.169248] pci 0000:4a:00.0: BAR 0: got res [0xc0200000-0xc02fffff] bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.189508] pci 0000:4a:00.0: BAR 0: moved to bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.206402] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.210637] pci 0000:40:05.0: IO window: disabled
[ 99.224856] pci 0000:40:05.0: MEM window: 0xc0200000-0xc03fffff
[ 99.230019] pci 0000:40:05.0: PREFETCH window: 0x000fc080000000-0x000fc097ffffff
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk will disable fast back to back transfer on the secondary bus
segment of the TI Bridge.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When injecting DRAM ECC errors (F3xBC_x8), EccVector[15:0] is a bitmask
of which bits should be error injected when written to and holds the
payload of 16-bit DRAM word when read, respectively.
Add /sysfs members to show the DRAM ECC section/word/vector.
Fail wrong injection values entered over /sysfs instead of truncating
them.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
On Fam10h and above, F1x[1, 0][7C:40] are DRAM Base/Limit registers
which specify the destination node of a DRAM address. Those address
boundaries are being extracted into ->dram_base[] and ->dram_limit[].
Correct the extraction masks to match the respective address bits.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Different processor families support a different number of chip selects.
Handle this in a family-dependent way with the proper values assigned at
init time (see amd64_set_dct_base_and_mask).
Remove _DCSM_COUNT defines since they're used at one place and originate
from public documentation.
CC: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This allows the errors to be further decoded and mapped to csrows.
Tested with ECC debug dimms and an Rev F cpu based system.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
