The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BUSWAIT is a 4-bit-wide value that controls the number of access waits
from the CPU to on-chip USB module. b'0000 inserts 0 wait (2 access
cycles) and b'1111 inserts 15 waits (17 access cycles, hardware
initial value), respectively.
BUSWAIT value depends on peripheral clock frequency supplied to on-chip
of each CPU, hence should be configurable through platform data.
Note that this patch assumes that b'0000 (0 wait, 2 access cycles) is
rerely used and considered as invalid. If valid 'buswait' data is not
provided by platform, initial b'1111 (15 waits, 17 access cycles) will
be applied as a safe default.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we run rmmod a gadget driver, the driver will call
disable_controller(). Then, because the bit of USBE in SYSCFG0 was
cleared in on_chip=1 mode, we could not connect the usb when we run
insmod a gadget driver next time.
This patch also cleans up probe() and ->stop() about unnecessary
init_controller().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Restoring the missing INDEX register value in musb_restore_context().
Without this suspend resume functionality is broken with offmode
enabled.
Cc: stable@kernel.org
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both fusb300 and langwell udcs seem to only
work with 32-bit address space.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- remove pointer u32 abuse in fusb300_fill_idma_prdtbl().
It is assigned the dma_addr to a pointer and then back.
Poor families may have to recycle variables but we don't
- don't free req.buf in error case. We don't do it in the
ok case so it is probably wrong to do it in error case.
- return in error case. There is no reason to continue
without data and performing ops on an invalid pointer.
- The if (d) statement is bogus since an invalid DMA pointer
is ~0 on some architecutres. And since we return for the
invalid case we don't need it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following compile warning:
| usb/gadget/ci13xxx_udc.c: In function 'show_registers':
| usb/gadget/ci13xxx_udc.c:1242:1: warning: the frame size of 2064 bytes is larger than 1024 bytes
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/net2272.c: In function ‘net2272_kick_dma’:
drivers/usb/gadget/net2272.c:740:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 6 has type ‘dma_addr_t’ [-Wformat]
drivers/usb/gadget/net2272.c: In function ‘net2272_queue’:
drivers/usb/gadget/net2272.c:859:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/langwell_udc.c: In function ‘queue_dtd’:
drivers/usb/gadget/langwell_udc.c:596:2: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_probe’:
drivers/usb/gadget/langwell_udc.c:3274:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3289:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_resume’:
drivers/usb/gadget/langwell_udc.c:3473:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3487:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
that code has been dead forever. Since the
first commit (0fe6f1d1) the use of that code
has been commented out. Let's drop the dead
code already and fix the following compile
warning:
| drivers/usb/gadget/fusb300_udc.c: At top level:
| drivers/usb/gadget/fusb300_udc.c:771:13: warning: ‘fusb300_wrfifo’ defined but not used [-Wunused-function]
| drivers/usb/gadget/fusb300_udc.c:1027:13: warning: ‘fusb300_set_ep_bycnt’ defined but not used [-Wunused-function]
Signed-off-by: Felipe Balbi <balbi@ti.com>
The autosuspend function can be disabled by unchecking the Macro
CONFIG_REALTEK_AUTOPM in kernel config file, by default, this macro is
turned on.
Signed-off-by: edwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a bug in Samsung's UDC driver, which is completely disabling
the USB device when a custom UDC command is used.
Following patch seems to get the right behavior (e.g. enabling pull-up
instead of disabling then Vcc is applied).
Signed-off-by: Viliam Mateicka <viliam.mateicka@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A compilation warning was added by the patch
"usb: gadget: use config_ep_by_speed() instead of ep_choose()".
This patch fixed it.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With this commit: cccad6d4b1
usb: otg: notifier: switch to atomic notifier
Following dumps are observed on attach/detach for MUSB HOST
mode and on a detach for MUSB Device mode.
BUG: sleeping function called from invalid context at kernel/mutex.c:85
where, the source is:
twl6030_usb_irq
->atomic_notifier_call_chain
->musb_otg_notifications
->twl6030_set_vbus
->twl_i2c_write_u8
->mutex_lock
This patch moves the i2c writes in set_vbus function to a
work-queue thereby avoiding I2C writes in atomic context.
Tested HOST and Device mode functionality on OMAP4460
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit 2edb11cbac fixed req->length in the composite_setup()
function, but that will cause all g_zero tests to fail like:
root#> ./testusb -D /proc/bus/usb/002/021 -t14 -c 15000 -s 256 -v 1
unknown speed /proc/bus/usb/002/021
/proc/bus/usb/002/021 test 14 --> 32 (Broken pipe)
We need to fix req->length in sourcesink_setup() as well to avoid this.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dev_get_drvdata() is exactly the same as
platform_get_drvdata(). Drop that useless
access to the platform device.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was somehow forgotten.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
bind() and pull is moved to udc core, call callbacks are verified by the
upper layer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udc-core checks for valid callbacks so there is no need for the driver
to do so. Also "can-be-bound-once" is verified by udc-core. The pull-up
callback is called by udc-core afterwords.
[ balbi@ti.com : keep holding gadget_driver pointer for now
remove the stupid check for gadget_driver otherwise
we don't handle IRQs ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udc_start() should only trigger the internal state machine and make
minimal house keeping. Before that call udc-core calls the bind()
callback and after the callback the pullup().
udc_stop() is simillar, udc-core calls pullup(), unbind() and finally
udc_stop().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The configuration is static however we only know the speed after we have
connected with the other side.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This value is now assigned during bind(). The configuration depends on
static values assigned by dummy driver itself. So there is no need to
defer this assigment until one know the actuall speed since the
configuration is static and known early.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is only required to be done once. There is no counter part to this
in ->stop() so there is no need to re-do it next time. While here also
init the max_stream size to 0 on SS speed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
maxpacket is set by the udc driver for ep0 very early. This value is
copied by the function gadget used later for the USB_DT_DEVICE and
USB_DT_DEVICE_QUALIFIER query. This seems to work fine so far. For USB3
we need set a different value here. In SS speed it is 2^x with x=9 and
in HS we set something <= 64. If the UDC starts in SS and continues in
HS after the cable has been plugged it will report a too small value.
There setting of this value is defered and taken automaticly from the
ep0 pointer where the UDC driver can update it according to the speed it
detected _after_ a cable has been plugged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
now that we have the udc class, we can allow
multiple gadget controller drivers to be
compiled as modules. This will allow for
distro-like kernels for embedded devices.
With this patch, I managed to build an x86
kernel with support for many of the controllers
enabled:
CONFIG_USB_FUSB300=m
CONFIG_USB_R8A66597=m
CONFIG_USB_M66592=m
CONFIG_USB_AMD5536UDC=m
CONFIG_USB_CI13XXX_PCI=m
CONFIG_USB_NET2272=m
CONFIG_USB_NET2280=m
CONFIG_USB_GOKU=m
CONFIG_USB_LANGWELL=m
CONFIG_USB_EG20T=m
Also an ARM kernel with support for many controllers:
CONFIG_USB_FUSB300=m
CONFIG_USB_OMAP=m
CONFIG_USB_R8A66597=m
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_M66592=m
CONFIG_USB_NET2272=m
CONFIG_USB_DUMMY_HCD=m
The next step would be to get rid of the
direct access to arch/ and mach/ directories
on some gadget controllers so that we can
build all of them without depending on their
respective ARCH_* symbols.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we start building glue layers as modules,
we need to be careful with the fifo_mode changes
otherwise that weird ifdeferry won't evaluate
correctly. Add the missing _MODULE variants for
all glue layers to prevent everybody from using
fifo_mode 2.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.
This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if we have more endpoints configured than
enabled on fifo_mode, then we need to be
careful on save/restore context operations,
otherwise we will try to access uninitialized
__iomem pointer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function has no user in my tree. It looks like it belongs to
net2280 but it somehow morphed into the dummy_hcd. So I remove it
before it spreads into more drivers.
After some digging I figured out that the only user was removed in
|commit 9079e91b5b
|Author: David Brownell <david-b@pacbell.net>
|Date: Wed May 7 16:00:36 2008 -0700
|
| USB: serial gadget: cleanup/reorg
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taking the correct struct once avoids doing the speed dance.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gadget_to_dummy_hcd() already does the speed check, so
it's unnecessary to unroll that all the time.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before commit 53832daea ("usb: gadget: dummy_hcd: use the shared_hcd
infrastructure") the is_otg field was set in dummy_udc_probe(). It seems
to me that this field is used in gadget's bind function. Therefore I'm
moving it before the bind() callback is called.
Cc: Tatyana Brokhman <tlinder@codeaurora.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The removed code does the same thing as dummy_pullup(). The only
difference is that in dummy_udc_stop() the first dummy_pullup()
did not call usb_hcd_poll_rh_status().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the gadget controller number is only used
during bind() to update descriptors and/or
check that a particular controller can support
a particular gadget driver.
Because of that, we can remove the ifdef
trickery as it's a rather small optimization
anyway.
While at that, also sort the entries
alphabetically and add a comment stating we
want to keep the list ordered alphabetically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 72c973d (usb: gadget: add usb_endpoint_descriptor
to struct usb_ep) has introduced a compile error to
ci13xxx_udc. Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This also fixes the error path: If the second device fails to register
we never remove the first one.
This is compile-tested only. I don't see any difference between those
two. Maybe we should just use one name instead?
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it udev won't be able to load the driver once it notices the
device unbound.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case pci_register_driver() fails it error will be 0 in case
platform_driver_register() was fine. Also without PCI
pci_register_driver() evaluates to 1 which is well, special. If
platform_driver_register() returns EINVAL or EBUSY we end up with 0.
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new module parameter to dummy_hcd
called is_high_speed.
When set to false the connected device will be forced
to operate in full-speed mode. By default, this parameter
is set to 'true'.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SS support to the dummy hcd module.
It may be used to test SS device when no (SS) HW is
available.
USB 3.0 hub includes 2 hubs - one HS and one SS. This
patch adds support for a SS root hub in the dummy_hcd
module.
A new module parameter was added: is_super_speed. When
set to true, a SS root hub will also be registered and
the connected device will be enumerated over the SS
root hub. The default of this parameter is false.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
[ balbi@ti.com : slight change to commit log
fixed one coding style issue ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
