Change data-argument type from (void *) to (u8 *) to prevent endianess
problems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return values are being initialised to zero only to be unconditionally
assigned to a few instructions later. This may give the impression that
zero is returned on success, which is not the case.
Note also that ftdi_NDI_device_setup never reports errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also remove unnecessary buffer allocations for zero-length transfers.
Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also fixes DMA transfer to stack for latency buffer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've got a crappy cypress converter here, and while running at higher
baud rates craps out on throughput, it works fine with lower ones.
While it'd be nice to simply use a lower baud rate, not all devices
can be configured this way, and it is possible to (slowly) interact
at higher rates by sending a byte at a time. So let people force
higher rates when they need it via a module parameter.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current code has a confusing duplicate new_baudrate init when setting
the serial parameters. So just combine the if statement checks to avoid
this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB_SERIAL_DEBUG Kconfig is for the USB serial debug driver, not for
generically enabling debug output in random USB serial drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My distro kernel (Fedora Rawhide) started throwing warnings from DMA API
checker, so I have no choice but band-aid it quick. There's no attempt
to reuse DMA buffers. Control messages are only sent rarely anyway.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed CS5 and CS6 from data bits since these are not supported
in FTDI hardware.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Latency timeout was read but never stored on port probe. When
ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0
rather than the default 16ms.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We always push characters to ldisc immediately regardless of
ASYNC_LOW_LATENCY.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Dell Computer Corp. Wireless 5720 VZW Mobile
Broadband (EVDO Rev-A) Minicard GPS Port. I stole the name from lsusb,
but my card does not have a GPS on it (at least not that I can make
function). I'm sure the patch is whitespace damaged but the one line
addition should be fairly straightforward nonetheless.
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add FTDI device IDs for several ELV devices and NXTCam of Lego Mindstorms NXT
- add hopefully helpful new_id comment
- remove less helpful "Due to many user requests for multiple ELV devices we enable
them by default." comment (we simply add _all_ known devices - an
enduser shouldn't have to fiddle with obscure module parameters...).
- add myself to DRIVER_AUTHOR
The missing NXTCam ID has been found at
http://www.unixboard.de/vb3/showthread.php?t=44155
, ELV devices taken from ELV Windows .inf file.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c
AD4USB measuring converter is a 4-input A/D converter which enables the
user to measure to four current inputs ranging from 0(4) to 20 mA or
voltage between 0 and 10 V. The measured values are then transferred to
a superior system in digital form. The AD4USB communicates via USB.
Powered is also via USB. datasheet in english is here:
http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdf
Signed-off-by: Radek Liboska <liboska@uochb.cas.cz>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a regression introduced by commit
715b1dc01f ("USB: usb_debug,
usb_generic_serial: implement multi urb write").
URB transfer buffer was never freed when using multi-urb writes.
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix a possible race bug in drivers/usb/serial/generic with
the new kfifo API.
Please apply it to the 2.6.33-rc* tree.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a (almost) sort-only patch to sort FTDI device
product ID definitions in new ftdi_sio_ids.h header.
Advantage is that new device ID submissions will now have a specific (sorted)
position - less future merge conflicts.
Compile-tested, based on _current_ mainline git.
Minor checkpatch.pl warnings were eliminated whereever it made sense,
very minor text changes.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).
Compile-tested, based on latest mainline git.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB serial code was a new user of the kfifo API, and it was missed
when porting things to the new kfifo API.
Please make the write_fifo in place. Here is my patch to fix the
regression and full ported version.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rename kfifo_put... into kfifo_in... to prevent miss use of old non in
kernel-tree drivers
ditto for kfifo_get... -> kfifo_out...
Improve the prototypes of kfifo_in and kfifo_out to make the kerneldoc
annotations more readable.
Add mini "howto porting to the new API" in kfifo.h
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the pointer to the spinlock out of struct kfifo. Most users in
tree do not actually use a spinlock, so the few exceptions now have to
call kfifo_{get,put}_locked, which takes an extra argument to a
spinlock.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new generic kernel FIFO implementation.
The current kernel fifo API is not very widely used, because it has to
many constrains. Only 17 files in the current 2.6.31-rc5 used it.
FIFO's are like list's a very basic thing and a kfifo API which handles
the most use case would save a lot of development time and memory
resources.
I think this are the reasons why kfifo is not in use:
- The API is to simple, important functions are missing
- A fifo can be only allocated dynamically
- There is a requirement of a spinlock whether you need it or not
- There is no support for data records inside a fifo
So I decided to extend the kfifo in a more generic way without blowing up
the API to much. The new API has the following benefits:
- Generic usage: For kernel internal use and/or device driver.
- Provide an API for the most use case.
- Slim API: The whole API provides 25 functions.
- Linux style habit.
- DECLARE_KFIFO, DEFINE_KFIFO and INIT_KFIFO Macros
- Direct copy_to_user from the fifo and copy_from_user into the fifo.
- The kfifo itself is an in place member of the using data structure, this save an
indirection access and does not waste the kernel allocator.
- Lockless access: if only one reader and one writer is active on the fifo,
which is the common use case, no additional locking is necessary.
- Remove spinlock - give the user the freedom of choice what kind of locking to use if
one is required.
- Ability to handle records. Three type of records are supported:
- Variable length records between 0-255 bytes, with a record size
field of 1 bytes.
- Variable length records between 0-65535 bytes, with a record size
field of 2 bytes.
- Fixed size records, which no record size field.
- Preserve memory resource.
- Performance!
- Easy to use!
This patch:
Since most users want to have the kfifo as part of another object,
reorganize the code to allow including struct kfifo in another data
structure. This requires changing the kfifo_alloc and kfifo_init
prototypes so that we pass an existing kfifo pointer into them. This
patch changes the implementation and all existing users.
[akpm@linux-foundation.org: fix warning]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (58 commits)
tty: split the lock up a bit further
tty: Move the leader test in disassociate
tty: Push the bkl down a bit in the hangup code
tty: Push the lock down further into the ldisc code
tty: push the BKL down into the handlers a bit
tty: moxa: split open lock
tty: moxa: Kill the use of lock_kernel
tty: moxa: Fix modem op locking
tty: moxa: Kill off the throttle method
tty: moxa: Locking clean up
tty: moxa: rework the locking a bit
tty: moxa: Use more tty_port ops
tty: isicom: fix deadlock on shutdown
tty: mxser: Use the new locking rules to fix setserial properly
tty: mxser: use the tty_port_open method
tty: isicom: sort out the board init logic
tty: isicom: switch to the new tty_port_open helper
tty: tty_port: Add a kref object to the tty port
tty: istallion: tty port open/close methods
tty: stallion: Convert to the tty_port_open/close methods
...
Opticon now takes the right mutex to check the port status but the status
check is done wrongly for the modern serial code, so fix it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty port has a port mutex used for all the port related locking so we
don't need the one in the USB serial layer any more.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Alan Stern pointed out - now we have tty_port_open the shutdown method
and locking allow us to whack the other bits into the full helper methods
and provide a shutdown op which the tty port code will synchronize with
setup for us.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the moment this just moves the USB logic over and fixes the 'what if
we open and hangup at the same time' race noticed by Oliver Neukum.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be switched
to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch deals with reducing the memory footprint for sierra driver.
This optimization is aimed for embedded software customers.
Some sierra modems can expose upwards of 7 USB interfaces, each possibly
offering different services. In general, interfaces used for the
exchange of wireless data require much higher throughput, hence require
more memory (i.e. more URBs) than lower performance interfaces. URBs
used for the IN direction are pre-allocated by the driver and this patch
introduces a way to configure the number of IN URBs allocated on a
per-interface basis. Interfaces with lower throughput requirements
receive fewer URBs, thereby reducing the RAM memory consumed by the
driver.
NOTE1: This driver has always pre-allocated URBs for the IN direction.
NOTE2: The number of URBs pre-allocated for the low-performance
interfaces has already been extensively tested in previous versions of
this driver.
We also added the capability to log function calls by adding DEBUG flag.
Please note that this flag is commented out because this is the default
state
for it.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add mark and space parity, since the device supports it.
Signed-off-by: Roland Koebler <r.koebler@yahoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).
To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=29a68e39d4a broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.
Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch presents fixes for the autosuspend feature implementation in
sierra usb serial driver in functions sierra_open(), sierra_close() and
stop_read_write_urbs().
The patch "sierra_close() must resume the device before it notifies it
of a closure" submitted by Oliver Neukum on Wed, October 14 has been
merged as fix in sierra_close() function.
The bug fix in sierra_open() function restores the autopm interface
state on error condition.
The bug fix in in stop_read_write_urbs() function assures that both
receive and interrupt urbs are recycled.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch presents a fix for the autosuspend feature implementation in
sierra usb serial driver for function sierra_send_setup(). Because it
is possible to call sierra_send_setup() before sierra_open() or after
sierra_close() we added a get/put interface activity to assure that the
usb control can happen even when the device is autosuspended.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Tested-by: Matthew Safar <msafar@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch for Airplus MCD 650 card
Note: This device is with Victor V Kudlak, and he confirmed that this
device works with the patch.
Signed-off-by: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial:visor: fix race between unthrottle and completion handler
visor_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
the same bug as opticon.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
many serial subdrivers are clearly written as if throttle/unthrottle
cannot sleep. This leads to unneeded atomic submissions. This
patch converts affected drivers in a way to makes very clear that
throttle/unthrottle can sleep. Thus future misdesigns can be avoided
and efficiency and reliability improved.
This removes any such assumption using GFP_KERNEL and spin_lock_irq()
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial:symbolserial: fix race between unthrottle and completion handler
symbol_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
the same bug as opticon.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial:opticon: fix race between unthrottle and completion handler
opticon_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial: fix flags in error case of suspension
suspended flag must be reset in error case
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial:visor: fix accounting in error case
data not pushed to the tty layer due to an error mustn't be counted
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic usbserial driver in Linux 2.6.31 halts its receiving
channel in response to throttle requests from the line discipline.
Unfortunately it drops the contents of the first URB received after
throttling takes effect. This patch corrects that problem.
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Acked-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the Dell inspiron mini 10, the GPS is connected via a cp2102. This patch
adds detection of this USB device. (I haven't managed to use the GPS under
Linux yet, though)
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1293) fixes a problem with the ipaq serial driver. It
tries to bind to all the interfaces, even those that don't have enough
endpoints. The symptom is an invalid memory reference and oops when
the device is plugged in.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable <stable@kernel.org>
Tested-by: Matthias Geissert <geissert@mathematik.tu-darmstadt.de>
Tested-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updated sierra driver version from 1.3.7 to 1.3.8 now that the autosuspend
capabilities were added to the driver.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method. This causes some drivers (io_ti in particular) to perform an
invalid memory access.
The patch adds a new flag to keep track of whether or not attach has
been called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression introduced in
39892da44b.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Re-structure read processing.
- Kill obsolete work queue and always push to tty in completion handler.
- Use tty_insert_flip_string instead of per character push when
possible.
- Fix stalled-read regression in 2.6.31 by using urb status to
determine when port is closed rather than port count.
- Fix race with open/close by checking ASYNCB_INITIALIZED in
unthrottle.
- Kill private rx_flag and lock and use throttle flags in
usb_serial_port instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove superfluous error checks in completion handler:
- No need to check private data and urb pointers as we check urb-status
before dereferencing priv (which is not freed until urb has been killed
on close).
- No need to check tty as it is checked again when processing.
- No need to check urb->number_of_packets on bulk urb.
Note that both private data and tty are checked again before processing
(possibly from work queue which also is cancelled on close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unused rx_byte counter which is never exposed as noted by Alan
Cox.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes tty_flip_buffer_push being called from hard interrupt context with
low_latency set.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following commit made console open fails while booting:
commit b50989dc44
Author: Alan Cox <alan@linux.intel.com>
Date: Sat Sep 19 13:13:22 2009 -0700
tty: make the kref destructor occur asynchronously
Due to tty release routines run in a workqueue now, error like the
following will be reported while booting:
INIT open /dev/console Input/output error
It also causes hibernation regression to appear as reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14229
The reason is that now there's latency issue with closing, but when
we open a "closing not finished" tty, -EIO will be returned.
Fix it as per the following Alan's suggestion:
Fun but it's actually not a bug and the fix is wrong in itself as
the port may be closing but not yet being destructed, in which case
it seems to do the wrong thing. Opening a tty that is closing (and
could be closing for long periods) is supposed to return -EIO.
I suspect a better way to deal with this and keep the old console
timing is to split tty->shutdown into two functions.
tty->shutdown() - called synchronously just before we dump the tty
onto the waitqueue for destruction
tty->cleanup() - called when the destructor runs.
We would then do the shutdown part which can occur in IRQ context
fine, before queueing the rest of the release (from tty->magic = 0
... the end) to occur asynchronously
The USB update in -next would then need a call like
if (tty->cleanup)
tty->cleanup(tty);
at the top of the async function and the USB shutdown to be split
between shutdown and cleanup as the USB resource cleanup and final
tidy cannot occur synchronously as it needs to sleep.
In other words the logic becomes
final kref put
make object unfindable
async
clean it up
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
[ rjw: Rebased on top of 2.6.31-git, reworked the changelog. ]
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
[ Changed serial naming to match new rules, dropped tty_shutdown as per
comments from Alan Stern - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/usb/serial/sierra.c: In function 'sierra_suspend':
drivers/usb/serial/sierra.c:936: error: 'struct usb_device' has no member named 'auto_pm'
Repairs
commit e6929a9020
Author: Oliver Neukum <oliver@neukum.org>
Date: Fri Sep 4 23:19:53 2009 +0200
USB: support for autosuspend in sierra while online
Cc: Greg KH <greg@kroah.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements support for autosuspend in the sierra driver while online.
Remote wakeup is used for reception. Transmission is facilitated with a queue
and the asynchronous autopm mechanism. To prevent races a private flag
for opened ports and a counter of running transmissions needs to be added.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is how "real" UARTs (e.g. 16550) work and AFAIK what RS232 specifies, too.
Make the driver more compliant.
Signed-off-by: Frank Schaefer <schaefer.frank@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device supports it, so why not use it ? Works fine !
Signed-off-by: Frank Schaefer <schaefer.frank@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the datasheets, the PL2303 supports a set of 25 baudrates.
The baudrate is set as a 4 byte value directly.
During my experiments with device 067b:2303 (PL2303X), I noticed that
- the bridge-controller always uses 9600 baud if invalid/unsupported baud rate
values are set
- the baud rate value returned by usb_control_msg(..., GET_LINE_REQUEST, ...)
does not reflect the actually used baudrate. Always the last set value is
returned, even if it was invalid and not used by the controller.
This patch fixes the following issues with the current code:
1.) make sure that only supported baudrates are set (are there any buggy
chip revisions out there which don't "like" other values... ?).
2.) always set the baudrate to the next nearest supported baudrate.
3.) applications can now read back the resulting baudrate properly, because
tty_encode_baud_rate(...) is now fed with the actually used baudrate.
Signed-off-by: Frank Schaefer <schaefer.frank@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using the module parameter vcc_default, you can choose the default VCC value.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
You can now set the IUU reader to 3.3V VCC instead of 5V VCC, using the sysfs
parameter vcc_mode. Valid values are 3 and 5.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resetting the device cause the device to have a new name in the /dev.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch to the ch341 driver which adds serial break support.
Signed-off-by: Tim Small <tim@seoss.co.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When do_output_char() attempts to write a carriage return/line feed sequence,
it first checks to see how much buffer room is available. If there are at least
two characters free, it will write the carriage return/line feed with two calls
to tty_put_char(). It calls the tty_operation functions write() for devices that
don't support the tty_operations function put_char(). If the USB generic serial
device's write URB is not in use, it will return the buffer size when asked how
much room is available. The write() of the carriage return will cause it to mark
the write URB busy, so the subsequent write() of the line feed will be ignored.
This patch uses the kfifo infrastructure to implement a write FIFO that
accurately returns the amount of space available in the buffer.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add IrDA support to ark3116 driver. This makes Gembird UIR-22 USB to IrDA
adapter work (vendor ID 0x18ec, device ID 0x3118). This adapter contains
ARK3116T USB serial chip and an IrDA transceiver, thus a command like
"irattach /dev/ttyUSB0 -s" is needed.
All magic numbers were captured using usbsnoop from windows driver that
came with the device.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if a subdriver has an additional suspend method, it must be called
first to allow the subdriver to return -EBUSY, because the second
half cannot be easily undone.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Spelling correction in Motorola USB Phone driver
Changed: * Mororola should be using the CDC ACM USB spec, but instead
To: * Motorola should be using the CDC ACM USB spec, but instead
Signed-off-by: Maxin B. John <maxinbjohn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are some unused variables in serial_do_down. Remove them.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds autosupport usable even in an always online mode.
- enables remote wakeup on open
- autoresume for sending
- timeout based autosuspend if nothing is sent or recieved
- autosuspend without remote wakeup support on open/close
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-off-by: Zhao Ming <zhao.ming9@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Detect the UART on interface1 and blacklist interface0 (as that is the
JTAG port).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices from the OpenDCC project are missing in the list
of the FTDI PIDs. These PIDs are listed at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
(Sorry for the german only page.)
This patch adds the three missing devices.
Signed-off-by: Rainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ID for Telit UC-864G GPS/UMTS/WCDMA modem and GPS receiver
to the option driver.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A few days ago i got the latest ZTE EVDO modem shown at:
http://img.alibaba.com/photo/240150115/ZTE_AC2726_EVDO_USB_Data_Modem.jpg
It seems that the latest kernel does not have support for it.
I wrote a small patch for the options.c module to add the relevant usb
ids to it.
From: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'd like to present my small patch enabling to use Sanwa PC5000
mulitimeter with linux.
Signed-off-by: Pawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'd like to present my small patch enabling to use Hameg HM8143 programmable
power supply with linux.
Signed-off-by: Pawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1292) modifies the USB serial console driver, to make it
compatible with the recent changes to the USB serial core. The most
important change is that serial->disc_mutex now has to be unlocked
following a successful call to usb_serial_get_by_index().
Other less notable changes include:
Use the requested port number instead of port 0 always.
Prevent the serial device from being autosuspended.
Use the ASYNCB_INITIALIZED flag bit to indicate when the
port hardware has been initialized.
In spite of these changes, there's no question that the USB serial
console code is still a big hack.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1291) removes a bunch of code from serial_open(), things
that were rendered unnecessary by earlier patches. A missing spinlock
is added to protect port->port.count, which needs to be incremented
even if the open fails but not if the tty has gotten a hangup. The
test for whether the hardware has been initialized, based on the use
count, is replaced by a more transparent test of the
ASYNCB_INITIALIZED bit in the port flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1290) adds some missing tests. serial_down() isn't
supposed to do anything if the hardware hasn't been initialized, and
serial_close() isn't supposed to do anything if the tty has gotten a
hangup (because serial_hangup() takes care of shutting down the
hardware).
The patch also updates and adds a few debugging lines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1289) renames serial_do_down() to serial_down() and
serial_do_free() to serial_release(). It also adds a missing call to
tty_shutdown() in serial_release().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1288) fixes the initialization logic in
serial_install(). A new tty always needs to have a termios
initialized no matter what, not just in the case where the lower
driver will override the termios settings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1287) makes serial_install() be reponsible for acquiring
references to the usb_serial structure and the driver module when a
tty is first used. This is more sensible than having serial_open() do
it, because a tty can be opened many times whereas it is installed
only once, when it is created. (Not to mention that these actions are
reversed when the tty is released, not when it is closed.) Finally,
it is at install time that the TTY core takes its own reference to the
usb_serial module, so it is only fitting that we should act the same
way in regard to the lower-level serial driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1286) changes usb_serial_get_by_index(). Now the
routine will check whether the serial device has been disconnected; if
it has then the return value will be NULL. If the device hasn't been
disconnected then the routine will return with serial->disc_mutex
held, so that the caller can use the structure without fear of racing
against driver unloads.
This permits the scope of table_mutex in destroy_serial() to be
reduced. Instead of protecting the entire function, it suffices to
protect the part that actually uses serial_table[], i.e., the call to
return_serial(). There's no longer any danger of the refcount being
incremented after it reaches 0 (which was the reason for having the
large scope previously), because it can't reach 0 until the serial
device has been disconnected.
Also, the patch makes serial_install() check that serial is non-NULL
before attempting to use it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1285) rearranges the subroutines in usb-serial.c
concerned with tty lifetimes into a more logical order: install, open,
hangup, close, release. It also updates the formatting of the
kerneldoc comments.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1284) changes the referencing of the usb_serial and
usb_serial_port structures in usb-serial.c. It's not feasible to make
the port structures keep a reference to the serial structure, because
the ports need to remain in existence when serial is released -- quite
a few of the drivers expect this. Consequently taking a reference
to the port when the device file is open is insufficient; such a
reference would not pin serial.
To fix this, we now take a reference to serial when the device file is
opened. The final put_device() for the ports occurs in
destroy_serial(), so that the ports will last as long as they are
needed.
The patch initializes all the port devices, including those in the
unused "fake" ports. This makes the code more uniform because they
can all be released in the same way. The error handling code in
usb_serial_probe() is much simplified by this approach; instead of
freeing everything by hand we can use a single usb_serial_put() call.
Also simplified is the port-release mechanism. Instead of being two
separate routines, port_release() and port_free() can be combined into
one.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found a tty refcnt leak in read_int_callback. In fact
it's handled wrong altogether. tty_port_tty_get can return NULL
and it's not checked in that manner.
Fix that by checking the tty_port_tty_get retval and put tty kref
properly.
http://stanse.fi.muni.cz/
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various drivers have hacks to mangle termios structures. This stems from
the fact there is no nice setup hook for configuring the termios settings
when the port is created
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And indeed none of them use it. Clean this up as it will make moving to a
standard open method rather easier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are handled by the tty_port core code which will raise and lower the
carrier correctly in tty_wait_until_ready
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB layer uses tty_hangup to deal with unplugs of the physical hardware
(analogous to loss of carrier) and then frees the resources. However the
tty_hangup is asynchronous. As the hangup can sleep we can use tty_vhangup
which is the non async version to avoid freeing resources too early.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem ioctls are not routed via the ioctl method so kill the old dead
code. The correct code is also already present and hooked in.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I made a correction for get_lsr_info, now it returns some meaningful
information. I tested it with two simultaneous simplex modem channels.
it is attached
Signed-off-by: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the tiocmget/mset handling on the mos7720 USB serial port.
[Minor space reformatting for coding style - Alan]
Signed-off-by: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached patch adds USB vendor and product IDs for Bayer's USB to serial
converter cable used by Bayer blood glucose meters. It seems to be a
FT232RL based device and works without any problem with ftdi_sio driver
when this patch is applied. See: http://winglucofacts.com/cables/
Signed-off-by: Marko Hänninen <bugitus@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I am submitting a patch for the pl2303 driver. This patch adds support
for the "Sony QN-3USB" cable (vendor=0x054c, product=0x0437). This USB
cable is a so-called data cable used to connect a Sony mobile phone to a
computer. Supported models are Sony CMD-J5, J6, J7, J16, J26, J70 and
Z7.
I have used this patch with my Sony CMD-J70 for several days and I
haven't encountered any kernel/hardware issue.
From: Khanh-Dang Nguyen Thu Lam <kdntl@yahoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for the Alcatel X060S/X200 broadband modems to the option
driver. The device starts in cd-rom emulation mode (1bbb:f000) and
requires the use of the usb_modeswitch tool to switch it to modem mode
(1bbb:0000).
Signed-off-by: Javier Martin <jmartinj@iname.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've opened up the case, and the chips in the ATEN UC2324 are:
Moschip
MCS7840CV-AA
69507-6B1
0650
(USB to 4-port serial)
(logo with AF kerned together) 0748
24BC02
SINGLP
(unknown 8-pin chip)
(logo looks like 3 or Z in circle)
ZT3243LEEA 0752
B7A16420.T
(4 chips, so this will be RS232 line driver)
(Probably equivalent of Sipex SP3243)
So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840,
and should use the mos7840.c driver. I expect you will remove the
aten2011.c driver from the staging area.
From the aten2011.c source code, the device ID for the UC2322 (2 port
serial) is 0x7820, just like the Moschip evaluation board. This value
should be added to the device id table of mos7840.c.
Here's a patch that adds these devices to the driver.
From: Russell Lang <gsview@ghostgum.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current listed Onda ids are ZTE devices. Replace them with ZTE id define
and add more ZTE device ids. Also remove 19d2:2000, this is the id when
device is first plugged in and is a CD-only device, before the switch
using eject.
These changes are based on a previous patch by Ming Zhao
<zhao.ming9@zte.com.cn>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Ming Zhao <zhao.ming9@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.
Signed-off-by: Ville Sundberg <vsundber@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed for compilation without CONFIG_PM.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After commit f092c24049 ("USB: option:
remove unnecessary and erroneous code") the variable 'serial' becomes
unused, as gcc-4.3.2 points out:
drivers/usb/serial/option.c: In function 'option_instat_callback':
drivers/usb/serial/option.c:834: warning: unused variable 'serial'
drivers/usb/serial/option.c: In function 'option_open':
drivers/usb/serial/option.c:930: warning: unused variable 'serial'
So I removed it.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes
- locking bug that was hidden by ecc2e05e73
- Regression #13821
- Spurious warning when closing and blocking for data write out
With these changes my PL2303 always ends up as ttyUSB0 when it should and
the module refcounts stay correct.
I'll do a more wholesale split & tidy of _open in the next release or two
as we get a standard tty_port_open and port->ops->init port->ops->shutdown
call backs.
Copy sent to Alan Stern and Carlos Mafra just to confirm it fixes all the
reports but it passes local testing with the same hardware as Alan Stern.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The port lock is used to protect the port state. However the port structure
is freed on a hangup, then the lock taken on a close. The right fix is to
drop the port on tty->shutdown() but we can't yet do that due to sleep v
non-sleeping rules. Instead do the next best thing and fix it up when we are
not in -rc season.
Reported-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function does not have an error return and returning an error is
instead interpreted as having a lot of pending bytes.
Reported by Jeff Harris who provided a list of some of the remaining
offenders.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1264) removes a bunch of unnecessary and erroneous stuff
from the option USB-serial driver. Clearly there's no need to verify
that the device pointer stored in the URBs is right or to store the
same pointer over again. After all, the pointer can't change once it
has been set up.
There's also no need to call usb_clear_halt for the IN endpoint
multiple times -- in fact, doing so is an error since every time after
the first there will be active URBs queued for that endpoint. Since
the Clear-Halts don't appear to be needed at all, the patch simply
removes them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1265) removes an erroneous call to usb_clear_halt from
the cypress_m8 driver. The call isn't valid because it is made from
interrupt context whereas usb_clear_halt is a blocking routine.
Presumably the code has never been executed; if it did it would cause
an oops. So instead treat -EPIPE like any other sort of unexplained
error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Updated the id_table with all devices that Sierra Wireless currently
support
- Re-ordered the contents of the id_table for better readability
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds USB ID for Turtelizer, an FT2232L-based JTAG/RS-232 adapter.
Signed-off-by: Krzysztof Ha³asa <khc@pm.waw.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1263) fixes a mixup that occurred when conflicting
patches for the sierra driver were merged incorrectly. The former
sierra_shutdown routine should have been become sierra_release, not
sierra_disconnect.
The symptom this fixes is an oops when the device file is closed after
a Sierra device has been unplugged (Bugzilla #13675).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Peter Naulls <peter@mushroomnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add A-Link 3GU device id 1e0e:9200 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3
by option driver.
The device appears first as CD-only 1e0e:f000 device and must be
switched to 1e0e:9200 mode either by using "eject CD" or
usb_modeswitch.
For the record, the device does not work with generic usbserial
driver (usb disconnect when sending the ATDT command).
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As reported by David Potts from Arkham Technology, the current driver
works with their hardware on addition of the device ids.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It enhances the driver for FTDI-based USB serial adapters to recognize and
support Northern Digital Inc (NDI) measurement equipment. NDI has been
providing this patch for various kernel flavors for several years and we would
like to see these changes built in to the driver so that our equipement works
without the need for customers to patch the kernel themselves.
The patch makes small modifications to 2 files: ./drivers/usb/serial/ftdi_sio.c
and ./drivers/usb/serial/ftdi_sio.h. It accomplishes 3 things:
1. Define the VID and PIDs to allow the driver to recognize the NDI devices.
2. Map the 19200 baud rate setting to our higher baud rate of 1.2Mb
We would have chosen to map 38400 to the higher rate, similar to what
several other vendors have done, but some of our legacy customers actually
use 38400, therefore we remap 19200 to the higher rate.
3. We set the default transmit latency in the FTDI chip to 1ms for our devices.
Our devices are typically polled at 60Hz and the default ftdi latency
seriously affects turn-around time and results in missed data frames. We
have created a modprobe option that allows this setting to be increased.
This has proven necessary particularly in some virtualized environments.
Signed-off-by: Martin P. Geleynse <mgeleyns@ndigital.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems an USB device with vendor id 0403 and product code FB80 has an
FTDI serial io chip as well: http://ftdichip.com/Drivers/D2XX.htm
This device in fact is a true random generantor by comsci:
http://comscire.com/Products/R2000KU/
So the following patch should add support for this device if I am
correct. Not tested as I do not own this device (I would like support in
the kernel so that my entropybroker application (which distributes
entrop data (random values) between servers and clients)).
From: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit 335f8514f2 introduced a
regression which stopped usb consoles from working correctly as a
kernel boot console as well as interactive login device.
The addition of the serial_close() which in turn calls
tty_port_close_start() will change the reference count of port.count
and warn about it. The usb console code had previously incremented
the port.count to indicate it was making use of the device as a
console and the forced change causes a double open on the usb device
which leads to a non obvious kernel oops later on when the tty is
freed.
To fix the problem instead make use of port->console to track if the
port is in fact an active console port to avoid double initialization
of the usb serial device. The port.count is incremented and
decremented only with in the scope of usb_console_setup() for the
purpose of the low level driver initialization.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Used by Virgin Mobile with the Broadband2Go service, for example.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1a1fab5137 accidentally added the
device id to both tables in the driver, which causes problems as this is
only a single port device, not a multiple port device.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch added Qisda(VID) & H21/H20(PID) into to supporting list.
Please help to check this patch,
From: Brad Lu <Brad.Lu@Qisda.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add modem portion of USB device labeled:
Model iCON 210, Qualcomm 3G HSDPA, designed in EU by Option
Device starts in usb-storage mode (1e0e:f000) and requires the use of a tool
like usb_modeswitch to switch it to modem mode (1e0e:9000).
Signed-off-by: Kai Engert <kaie@kuix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The product ID's for the following devices have been added:
- LOAD-n-GO
- ICD-U64
- PRIME-8
Signed-off-by: Jan Capek <jan@ccsinfo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I recently bought a PC interface for the Cressi Edy dive computer
(www.cressi.it) and discovered that it uses the pl2303 chip, albeit
with ad-hoc vendor and product ids (04b8, 0521 respectively). Being in
the process of writing a linux software for such device (cressi only
provides a windows software), I patched the pl2303 linux driver to
have the interface recognized. I am submitting you the patch (very
basic) for inclusion in next kernel version.
From: Gianpaolo Cugola <gianpaoloc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PL2303 has private data shovelling methods that also have no fast path. Fix
them to work the same way as the default handler.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysrq code acquired a kref leak. Fix it by passing the tty separately
from the caller (thus effectively using the callers kref which all the
callers hold anyway)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can't go around calling all sorts of magic per character functions at
full rate 3G data speed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit 335f8514f2 has stopped
properly checking if there is any usb serial associated with the tty in
the close function. It happens the close function is called by releasing
the terminal right after opening the device fails.
As an example, open fails with a non-existing device, when probe has
never been called, because the device has never been plugged. This is
common in systems with static modules and no udev.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1254) splits up the shutdown method of usb_serial_driver
into a disconnect and a release method.
The problem is that the usb-serial core was calling shutdown during
disconnect handling, but drivers didn't expect it to be called until
after all the open file references had been closed. The result was an
oops when the close method tried to use memory that had been
deallocated by shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1253) prevents the usb-serial core from calling a
driver's port_probe and port_remove methods more than once per port.
It also removes some unnecessary try_module_get() calls and adds a
missing port_remove method call in a failure path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only time a sysrq should get processed is if the attached device
is a console. This is intended to protect sysrq execution on a host
connected with a terminal program.
Here is the problem scenario:
host A <-- rs232 link --> host B
Host A is using mincom and a usb pl2303 device to connect to host b
which is a linux system with a usb pl2303 device acting as the serial
console. When host B is rebooted the pl2303 emits random junk
characters on reset. These character sequences contain serial break
signals most of the time and when translated to a sysrq have caused
host A to get random processes killed, reboots or power down.
It is true that in this setup with this patch host B might still have
the same problem as host A if you reboot host A. In most cases host A
is a development host which seldom gets rebooted, and you could turn
off sysrq temporarily on host B if you need to reboot host A.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add callbacks to process the sysrq when using a pl2303 usb device as a
console.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/serial/sierra.c: In function 'sierra_write':
drivers/usb/serial/sierra.c:375: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Cc: Rory Filer <rfiler@SierraWireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Removed potential kernel oops from sierra_calc_num_ports() function.
Calling this function twice would likely have caused an oops because
the function releases allocated memory after the first call.
- Modified sierra_probe() function to reflect the changes in
sierra_calc_num_ports().
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Fixed a problem when re-submitting urb from interrupt callback in
function sierra_instat_callback(). This suppresses also issuing of
error messages in /var/log/kern.log
- Removed redundant debug message at the beginning of
sierra_instat_callback() function
- Changed a debug message to be an error message
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Fixed a problem with transferring packets with size a multiple of Bulk
Xfer size in function sierra_write(). Added transfer flag
URB_ZERO_PACKET before submitting the urb to trigger Zero-length data
transfer when packet size is a multiple of Bulk Xfer.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change driver to make use of the new functions in
include/linux/usb/serial.h so as to allow the driver to handle the
sysrq
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_debug driver was modified to implement serial break handling
by using a "magic" data packet comprised of the sequence:
0x00 0xff 0x01 0xfe 0x00 0xfe 0x01 0xff
When the tty layer requests a serial break the usb_debug driver sends
the magic packet. On the receiving side the magic packet is thrown
away or a sysrq is activated depending on what kernel .config options
have been set.
The generic serial driver was modified as well as the usb serial
headers to generically implement sysrq processing in the same way the
non usb uart based drivers implement the sysrq handling. This will
allow other usb serial devices to implement sysrq handling as desired.
The new usb serial functions are named similarly and implemented
similarly to the uart functions as follows:
usb_serial_handle_break <-> uart_handle_break
usb_serial_handle_sysrq_char <-> uart_handle_sysrq_char
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern commented that the private driver counts must be updated
regard less of the status return on the urb when the write call back
is executed.
This patch alters the behavior to update the private driver counts by
simply moving the status check to after the driver count update.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_debug driver, when used as the console, will always fail to
insert the carriage return and new line sequence as well as randomly
drop console output. This is a result of only having the single
write_urb and that the tty layer will have a lock that prevents the
processing of the back to back urb requests.
The solution is to allow more than one urb to be outstanding and have
a slightly deeper transmit queue. The idea and some code is borrowed
from the ftdi_sio usb driver.
The generic usb serial driver was modified so as to allow the classic
method of 1 write urb, or a multi write urb scheme with N allowed
outstanding urbs where N is controlled by max_in_flight_urbs. When
max_in_flight_urbs in a "struct usb_serial_driver" is non zero the
multi write urb scheme will be used.
The size of 4000 was selected for the usb_debug driver so that the
driver lowers possibility of losing the queued console messages during
the kernel startup.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem in function sierra_indat_callback() which
would stop receiving traffic from a modem if a number of URB failures
occur. Failed URBs are not resubmitted for the next read and there is
only a limited number of URBs allocated for the IN path. After this
number of failures, the receive path stops working on a particular
interface.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
- Updated Copyright notice with new authors names
- Version number set to 1.3.6
- Added a MAX_TRANSFER constant following Greg Kroah-Hartman's
recommended setting of PAGE_SIZE-512 for USB transfer buffers and
modified accordingly sierra_write() function.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch removes the call to usb_reset_device which may occur
when closing the driver by implementing a new session initialization
code based on the method used by gpsbabel.
The patch is against linux-2.6.30-rc3-git1.
Signed-off-by: Hermann Kneissel herkne@users.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Identify the Novatel MC760/U760/USB760 in the option USB serial driver.
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Version number set to 1.3.5
- Added "\n" at the end of each string in dev_dbg() code to improve the debug
information visibility. Without this change the debug logs are very
difficult to read.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Version number set to 1.3.4
- Increased the number of input/output URBs for improved performance
(numbers based on an measurement study triggered by a user request).
We performed the testing using a network simulator that provided full
speeds in the uplink and downlink directions and this combination of
URBs provided the best throughput.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes all the unnecessary "\n"s that the debug print
statements have, which result in everything appearing double spaced
and unreadable in the logs.
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
D-Link DWN-652 in Modem mode exposes 3 interfaces
- First one is the USB storage one
- Second one is for both control and connection
- Third one is unknown
This patch avoids usb-storage trying to switch again when already in
modem mode, and exposes only 2 ttyUSB instead of 3 by not attaching
to the storage interface
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added a function to set the packet size to be used based on the value from the
device endpoint descriptor. The FT2232H and FT4232H hi-speed devices will have
wMaxPacketSize of 512 bytes when connected to a USB 2.0 hi-speed host, but will
use alternative descriptors with wMaxPacketSize of 64 bytes if connected to a
USB 1.1 host or hub. All other FTDI devices have wMaxPacketSize of 64 bytes,
except some FT232R and FT245R devices which customers have mistakenly
programmed to have wMaxPacketSize of 0 - this is an error and will be
overridden to use wMaxPacketSize of 64 bytes. The packet size used is
important as it determines where the driver removes the status bytes from the
incoming data. If it is incorrect, it will lead to data corruption.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for FTDI's USB 2.0 hi-speed devices - FT2232H (2
interfaces) and FT4232H (4 interfaces), including a new baud rate
calculation for these devices which can now achieve up to 12Mbaud by
turning off a divide by 2.5 in the baud rate generator of the chips. In
order to achieve baud rates of <1200 baud, the divide by 2.5 must be
active. The default product ID of the FT2232H is 0x6010 (same as the
FT2232C IC). The default PID of the FT4232H is 0x6011.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the Toshiba HSDPA Minicard (which is just a
rebranded Novatel EU870D) used in some Toshiba laptops.
This is my first patch attempt, I hope I got the conventions right.
Signed-off-by: Michele Valzelli <valz@messagenet.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to have added new device to usbserial/ftdi_sio driver.
These ids used USB track device (http://www.l-and-b.dk/access_alt.html).
They use differend device IDs, but it works as standard usb-serial
conventer.
From: Daniel Suchy <danny@danysek.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Interface blacklisting is necessary for non-serial interfaces that are handled
by a different driver. The interface blacklisting is implemented in sierra
driver per device. Each device in need of a blacklist has a static information
array kept in the driver. This array contains the interface numbers that are
blacklisted. The pointer for each blacklist array and the length
of that blacklist are 'bundled' in data structure sierra_iface_info. A pointer
to this information is set in id_table when the device is added to the id_table.
The following is summary of changes we have made to sierra.c driver in
this patch dealing with interface blacklisting support:
- Added data structure sierra_iface_info and function is_blacklisted()
to support blacklisting
- Modified sierra_probe() to handle blacklisted interfaces accordingly
- Improved comments in id_table
- Added new device in id_table with blacklist interface support
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[Folded from eight patches into one as the original set according to the
author "All of the patches need to be applied to obtain a working product"
so keeping them split seems unhelpful
Merge fixes done versus other conflicting changes and moved the
spin_lock_init from open to setup time -- Alan]
Summary of the changes and code re-organization in this patch:
- The memory for urbs is allocated and urbs are submitted only for the active
interfaces (instead of pre-allocating these for all interfaces). This will
save memory especially in the case of using composite devices.
- The code has been re-organized and functionality has been extracted from
sierra_startup(), sierra_shutdown(), sierra_open(), sierra_close() and added
in helper functions sierra_release_urb(), sierra_stop_rx_urbs(),
sierra_submit_rx_urbs() and sierra_setup_urb()
- Added function sierra_release_urb() to free an urb and its transfer
buffer.
- Removed unecessary include file reference and comment.
- Added function sierra_stop_rx_urbs() that takes care of the release of
receive and interrupt urbs. This function is to be called by sierra_close()
whenever an interface is de-activated.
- Added new function sierra_submit_rx_urbs() that handles the submission of
receive urbs and interrupt urbs (if any) during the interface activation.
This function is to be called by sierra_open(). Added a second parameter to
pass the memory allocation (as suggested by Oliver Neukum) so that this
function can be used in post_reset() and resume().
- Added new function sierra_setup_urb() that contains the functionality to
allocate an urb, fill bulk urb using the supplied memory allocation flag
and release urb upon error. Added parameter so that the caller pass the
memory allocation flag for flexibility.
- Moved sierra_close() before sierra_open() to resolve dependencies
introduced by the code reorganization.
- Modified sierra_close() to call sierra_stop_rx_urbs() and
sierra_release_urb() functions added in previous patch.
- Modified sierra_open() to call sierra_setup_urb() and sierra_submit_rx_urbs()
functions; note urbs are allocated and submitted for each activated interface.
- Modified sierra_startup() so that allocation of urbs happens whenever an
interface is activated (urb allocation is moved to sierra_open()).
- Modified sierra_shutdown() so that urbs are freed whenever an interface is
de-activated (urb freeing moved to sierra_close() as shown in previous patch
from the series)
- Removed unecessary data structure from sierra_port_private_data
- Suppress an entry in logs by not re-submitting an urb when usb_submit_urb()
returns -EPERM, as this shows that usb_kill_urb() is running (as suggested by
Oliver Neukum)
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The various merges into the sierra driver inadvertently undid
commit 212b8f0c3f by Elina Pasheva
<epasheva@sierrawireless.com>. Put it back so the OBEX port works again.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new open/close logic handles DTR and friends, so don't do it in our own
open routine as well.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows users to use the standard setserial command with this FT232
feature as well as obscure chip specific interfaces we have now. We keep
track of and respect the sysfs value for non-low-latency cases. In theory we
could do smart stuff with VTIME and the like but this seems of questionable
worth.
Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=9120
Signed-off-by: Alan Cox <alan@linux.intel.com)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces the string "CP2101" with "CP210x" within cp210x.c
This is to reduce confusion about the fact that the driver is actually
compatible with CP2101, CP2102 and CP2103 devices.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
(Fixed some collisions merging)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CP210X driver was developed without official device specifications.
This has lead to an incorrect assumption that all GET request codes are
equal to the corresponding SET request code +1.
This patch removes this incorrect assumption, and uses request code
definitions based on the updated GPL driver from SiLabs.
This modification is needed before extended functionality such as GPIO
on CP2103 can be supported.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set_termios can now be used for setting the parity and the stopbits. This is
needed to use with cards which use a different parity then the parity used at
start (even).
If the iuu_uart_baud function return an error, we will return the old_termios
instead of the new one.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
This was then revamped to use the various helpers, not copy non-hardware
bits any to add mark/space parity and csize reporting
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring in the relevant bits of the 0.9 vendor driver.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1244) fixes a crash in usb-serial that occurs when a
sub-driver returns a positive value from its attach method, indicating
that new firmware was loaded and the device will disconnect and
reconnect. The usb-serial core then skips the step of registering the
port devices; when the disconnect occurs, the attempt to unregister
the ports fails dramatically.
This problem shows up with Keyspan devices and it might affect others
as well.
When the attach method returns a positive value, the patch sets
num_ports to 0. This tells usb_serial_disconnect() not to try
unregistering any of the ports; instead they are cleaned up by
destroy_serial().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.
That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).
The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().
Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.
Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1238) adds proper reference counting for ftdi_sio's
private data structure. Without it, the driver will free the
structure while it is still in use if the user unplugs the serial
device before closing the device file.
The patch also replaces a slightly dangerous
cancel_delayed_work/flush_scheduled_work pair with
cancel_delayed_work_sync, which is always safer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes tty->low_latency from all USB serial drivers that push
data into the tty layer at hard interrupt context. It's no longer needed
and actually harmful.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem in sierra_send_setup() function when
composite devices are used. One should not be sending ACM commands to
interfaces that are OBEX. Doing this causes an apparent failure as the
ACM command has to time out before the interface can start being used.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem with any mos7840 device where the use of the field "minor" before it is
initialised results in all the devices being overlaid in memory (minor = 0 for all instances)
Contributed by: Phillip Branch
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add USB ids for the mos7840 based ATEN International serial devices.
Contributed by: Phillip Branch
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1229) fixes a few lifetime and locking problems in the
usb-serial driver. The main symptom is that an invalid kevent is
created when the serial device is unplugged while a connection is
active.
Ports should be unregistered when device is disconnected,
not when the parent usb_serial structure is deallocated.
Each open file should hold a reference to the corresponding
port structure, and the reference should be released when
the file is closed.
serial->disc_mutex should be acquired in serial_open(), to
resolve the classic race between open and disconnect.
serial_close() doesn't need to hold both serial->disc_mutex
and port->mutex at the same time.
Release the subdriver's module reference only after releasing
all the other references, in case one of the release routines
needs to invoke some code in the subdriver module.
Replace a call to flush_scheduled_work() (which is prone to
deadlocks) with cancel_work_sync(). Also, add a call to
cancel_work_sync() in the disconnect routine.
Reduce the scope of serial->disc_mutex in serial_disconnect().
The only place it really needs to protect is where the
"disconnected" flag is set.
This fixes the bug reported in
http://bugs.freedesktop.org/show_bug.cgi?id=20703
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dan Williams <dcbw@redhat.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The v950 appears to be a ruggedized version of the Motorola Razor
phone. Tethering to the phone to use it in 'phone as modem' mode
requires the use of the specialized moto-modem driver which layers
over the usb-serial driver. Support for the v950 was added simply
adding the device ID's for the phone.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 664d5df92e upstream.
Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS
Features still missing:
- character length other than 8 bits
- parity settings
- break control
I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.
Usage example by Tollef Fog Heen :
TEMPer USB thermometer <http://err.no/src/TEMPer.c>
based on a patch by:
From: Tollef Fog Heen <tfheen@err.no>
* Implement support for all baud rates rather than just a hard
coded set.
* Make it possible to control status and control lines
* Grab a bunch of #defines from FreeBSD to reduce the number of
magic numbers in the file
Signed-off-by: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Signed-off-by: Boris Hajduk <boris@hajduk.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Tollef Fog Heen <tfheen@err.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reverts commit 664d5df92e as the commit
log information was not complete, and we didn't have a proper
signed-off-by by the author of the original BSD code.
Cc: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Cc: Boris Hajduk <boris@hajduk.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a set of device IDs from the Windows drivers. These aren't complete
(there's a couple of cases where a QDL device is identified without the
associated modem being identified), but it's better than the current
situation.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows D-Link DWM-652 3.5G modem to work.
It is an express card but was only tested with the provided usb adapter as I
don't have machines with express card connector.
/dev/ttyUSB{0,1,2} get created, and using comgt on ttyUSB1 works fine :
[root@plop tmp]# comgt -d /dev/ttyUSB1 -e
Enter PIN number: XXXX
Waiting for Registration..(120 sec max).
Registered on Home network: "Orange France",2
Signal Quality: 15,99
From: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the ti-usb adapter returns an zero data length frame (which happens)
then we leak a kref. Found by Christoph Mair <christoph.mair@gmail.com>
who proposed a patch. The patch here is different as Christoph's patch
didn't work for the case where tty = NULL and data arrived but Christoph
did all the hard work chasing it down.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are various bits of code here that are unfinished and instead of
being harmless either confuse or spew stuff into the logs at higher than
debug level. They can and should go away.
Also remove the bogus use of tty->lowlatency. We fixed the need for this hack
long ago (with the flip buffer rewrite) but people keep copying it into drivers.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
This is really a follow up to the modifications Alan Cox made for commit
95da310e66 to pass a tty_struct to various
interface functions, which broke the serial configuration (termios) functions
when the device is being used as a console. These changes restore the
configuration to proper functioning both as a tty and as a console. As Alan
notes in that commit, these changes will need to be tweaked when we have
a proper console abstraction.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ipaq driver currently enforces one port on all devices. This
is correct for 2 and 3 endpoint devices, but with 4 endpoint devices
meaningful communication occurs on the second pair.
This patch allows 2 ports for 4 endpoint devices.
Signed-off-by: Mark Ellis <mark@mpellis.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lots of users are getting confused about the cp2101 driver. It really
does support more than just the cp2101 device, so rename it to cp210x to
try to prevent confusion.
Cc: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch lowers the logging priority of certain messages to prevent
users from flooding the log files.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the extended range of baud rates supported
by CP2102 and CP2103 devices described in SiLabs AN205. An additional
function cp2101_quantise_baudrate rounds the baud rate as per AN205
Table 1. A modification to the baud rate calculation removes a rounding
error, allowing the full range of baud rates to be used.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
actual_length should also be a u32 and not a signed value. This patch
changes this field to be 'u32' to prevent any potential negative
conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following bug:
.plug ch341 usb serial port into a hub port;
.ch341 driver bound to the device and /dev/ttyUSB0 comes
.open /dev/ttyUSB0 by minicom and we can use the serial successfully
.suspend the ch341 usb serial device(such as: echo suspend > power/level)
.resume the ch341 usb serial device (such as: echo on > power/level)
.new port /dev/ttyUSB1 comes ,and the original /dev/ttyUSB0 still exists,
but is no longer usable by minicom
The patch adds suspend and resume callback to ch341 usb driver to prevent it
from unbinding during suspend. The /dev/ttyUSB0 is not released until being
closed, so /dev/ttyUSB1 comes after resume, and the original /dev/ttyUSB0 is
no longer usable by minicom. It is really a mess for a minicom user.
This patch also adds the reset_resume callback to make it usable after resuming
from STR or hibernation, for generally STR or hibernation will make the vbus
of root-hub lost.
Finally enable the driver's supports_autosuspend, for the device is in working
order with it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With "nousb" cmdline booting, built-in serial drivers (ie. airecable)
will trigger kernel oops.
Indeed, if nousb, usb_serial_init will failed, and the usb serial bus type
will not be registerd, then usb_serial_register call driver_register
which try to register the driver to a not registered bus.
Here add usb_disabled() check in usb_serial_register to fix it.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver originally written by Qualcomm, but rewritten by me due to the
totally different coding style. Cleaned up the probe logic to make a
bit more sense, this is one wierd device. They could have prevented all
of this by just writing sane firmware for the modem.
Cc: Tamm Liu <tamml@qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to figure out what userspace programs are expecting from this
driver, so log them so we can try to get it right.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is for the Symbol 6608 barcode scanner in a fake "HID" mode.
Thanks to Dalibor Grgec for working with me to get this to start to work
properly.
Cc: Dalibor Grgec <dalibor.grgec@zemris.fer.hr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A USB-serial converter device is plugged into a system, and a process
opens it's device node. If the device is physically removed whilst the
process still has its device node open, then other processes can
sucessfully open the now non-existent device's node. I would expect
that open() on a device that has been physically removed should return
ENODEV.
This is manifesting itself with getty on my system. I do the following:
1. set up inittab to spawn getty on ttyUSB0, eg:
T1:23:respawn:/sbin/getty -L ttyUSB0 115200 vt100
2. Plug in USB-serial converter cable
3. Wait for a login prompt on a terminal program attached to the serial
cable
4. Login
5. Pull the USB-serial converter cable from the box
6. getty doesn't realise that ttyUSB0 no longer exists as /dev/ttyUSB0
can still be opened.
7. Re-insert the USB-serial converter cable
8. You should no longer get a login prompt over the serial cable, as
the the USB-serial cable now shows up as /dev/ttyUSB1, and getty is
trying to talk to /dev/ttyUSB0.
The attached patch will cause open("/dev/ttyUSB0", O_RDONLY) to return
ENODEV after the USB-serial converter has been pulled. The patch was
created against 2.6.28.1. I can supply it against something else if
needs be. It is fairly simple, so should be OK.
I am using a pl2303 device, although I don't think that makes any
difference.
From: James Woodcock <James.Woodcock@ACULAB.COM>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the fallback to the generic method. It is cleaner to
explicitely request it. Introducing this was my mistake. This will
be solved by an explicit test and the driver being allowed to request
what it needs to be done upon resumption.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets userspace determine what the state of the RTS line is, which
is what is needed to properly handle data flow for this device (it
raises RTS when there is data to be sent from it.)
Cc: Kees Stoop <kees.stoop@opticon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some pointless messages from the FTDI serial driver;
I found these filling up syslog on one system. Also remove
a pointless "break" after a "return" in the same area.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes use of the generic method if a serial driver provides
no implementation. This simplifies implementing suspend/resume support
in serial drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This exports a symbol for usb_serial_generic_resume, so that modules can
use it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes an unnecessary check for autoresume from the generic
resume method. The check has been obsoleted by the now delayed
increase of the usage counter which makes the error this check prevented
impossible. This change allows drivers which only use the bulk read URB
the use of the generic method even if they support autosuspend.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a flag into the usb serial layer to tell drivers
that their URBs are killed due to suspension. That is necessary to let
drivers know whether they should report an error back.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Hi Greg,
this is for 2.6.30. Patches to use this in drivers are under development.
Regards
Oliver
this does the standard support for suspend/resume for the opticon
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements suspend and resume methods for the
option driver. With my hardware I can even suspend the system
and keep up a connection for a short time.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS
Features still missing:
- character length other than 8 bits
- parity settings
- break control
I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.
Usage example by Tollef Fog Heen :
TEMPer USB thermometer <http://err.no/src/TEMPer.c>
Signed-off-by: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Signed-off-by: Boris Hajduk <boris@hajduk.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
priv is checked not to be NULL near the beginning of the function and not
changed subsequently, making the test redundant.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x@p1 == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)
// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@
... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)
@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@
(
- if ((x@p2 != NULL) || ...)
S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Option GTM380 in Modem mode uses Product ID 0x7201. This has been tested and works
on production systems for over 6 months.
Signed-off-by: Achilleas Kotsis <akots@exponent.gr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* newer versions of the Novatel Wireless U727 CDMA 3G USB stick
have a different Product ID (0x5010); adding this ID makes them
work just fine with the option driver
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic cdc-acm driver is now the best one to handle Sony Ericsson
F3507g-based devices (which the Dell 5530 is a rebrand of), now that all
the pieces are in place (ie, cac477e8f1).
Removing the IDs from option allows cdc-acm to handle the device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please consider this small patch for the usb option-card driver.
This patch adds the ZTE 622 usb modem device.
Signed-off-by: Albert Pauw <albert.pauw@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that my revision of the F3507G WWAN card isn't listed in
drivers/usb/serial/option.c
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addes the BenQ 3g modem support to the option driver.
From: Jesse Sung <jsung@novell.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- New Novatel and Dell mobile broadband modem products added
- Dell pid variables used in stead of numerical PIDs for known
products
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds device IDs and balances the counts to make the
hot ID additioning mechanism work.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Cc: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was one error path where unlock_kernel() wasn't called.
This was found with a code checker (http://repo.or.cz/w/smatch.git/)
Compile tested only, sorry.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the NDI Polaris system *http://www.ndigital.com/).
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The failure path of aircable_init is wrong, fix the order of (goto) labels.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert 8b6346ec89 as these devices really
work just fine with the cdc-acm driver, as they follow the spec
properly.
Thanks to Chuck Ebbert for pointing out the problem here.
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: Marcel Sebek <sebek64@post.cz>
Acked-by: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: Robie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,
PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c
From: Tomasz K <eros81@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor/product ID of the fasttrax GPS evaluation kit from:
http://www.fastraxgps.com/products/evaluationtools/evaluationkit/
to the cp2101 module since this device is actually equipped with a
CP210x USB to serial bridge.
The vendor/product ID is: 0x10c4/0x826b.
Signed-off-by: Wolfgang Glas <wolfgang.glas@ev-i.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 4a90f09b20 added kref stuff to
ftdi_sio, but missed tty_kref_put at one exit point in
ftdi_process_read.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the Multi-Tech cellular modem firmware to the TI USB serial driver.
This firmware was extracted from:
ftp://ftp.multitech.com/wireless/wireless_linux.zip
Firmware licence: "all firmware components are redistributable in binary
form" per support@multitech.com
Copyright (C) 2005 Multi-Tech Systems, Inc.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Multi-Tech cellular modem support to the ti_usb_3410_5052 driver.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TI USB serial driver supports specifying alternate vendor and
product IDs (since the chips can and are used in devices under other
vendor/product IDs). However, the alternate IDs were not loaded in the
combined product table. This patch also adds support for loading
alternate firmware for alternate vendor/product IDs.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawell found a case where a NULL check was misplaced in the
usb-serial code. However as the object in question cannot be NULL the
check can simply be removed.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver got rescued from a few years ago and was requested to be
added. So I cleaned it up, ported it to the latest kernel version and
here it is.
Cc: Thomas Hergenhahn <thomas.hergenhahn@suse.de>
Cc: Emmanuele <iemmav@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should speed up the option driver's upload speed quite a bit. It has been tested by a number of different people on different devices with success.
Cc: Roland Wolters <roland.wolters@credativ.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the usb-serial drivers are starting to use urb->status in ways
they should not be doing. This fixes up some of them to prevent that.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need the BKL here any more so it can go. In a couple of spots the
driver requirements are not clear so push the lock down into the driver.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The underlying problem is that the device methods don't all correctly
handle disconnected status and some keep reporting bytes pending which
causes tcdrain to stall.
When the cable is unplugged they are definitely gone, and as this is true
for all USB cables we can fix it in the core usb serial code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add device funtion for usb serial console, so we can open /dev/console
when we use a usb serial device as console.
(Typecast removed as noted by Sergei Shtylyov)
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB serial has always had races where the tty port usage count can hit zero
during a receive event. The internal locking is a mutex so we can't use
that in the IRQ handlers.
With krefs we can tackle this differently but we still need to be careful.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add id for the Hewlett-Packard LD220-HP POS pole display.
Bus 002 Device 002: ID 03f0:3524 Hewlett-Packard
Signed-off-by: Mike Provencher <mike.provencher@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver transfers firmware. It may just as well set the correct
configuration.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the "Superial" USB-Serial converter to pl2303 so that it
is detected, by the correct driver. Adds the relevant vendor:product
(5372:2303) to the device tables in pl2303.c & pl2303.h. The patch has
been tested against 2.6.24-22-generic.
Signed-off-by: Matthew D Arnold <matthew.arnold-1@uts.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone on rmweb reminded me this had been overlooked from ages ago..
Add the identifiers for the Sprog II USB. This is a DCC control interface
using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been
using it with insmod options for ages, this just puts it into the driver
data.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[Folded together as one diff from 3]
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch which adds IDs for AKTAKOM USB->RS232 cable
(http://www.aktakom.ru/product/kio/ace-1001.htm) is attached.
From: M Kondrin <mkondrin@hppi.troitsk.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enfora GSM2228 based on Cygnal Integrated Products chip uses the same
cp2101 driver.
Signed-off-by: Damir N Abdullin <damir@mimas.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds YISO u893 usb modem vendor and product ID to option.c.
I had a better experience using this modification and the same system.
Signed-off-by: Leslie Harlley Watter <leslie@watter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we close we must clear the extra reference we got when we read
port->tty. Setting the port tty NULL will clear the kref held by the driver
but not the one we obtained ourselves while doing the lookup.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Helge Hafting <helge.hafting@aitel.hist.no>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In this patch, we want to do one thing: add more Huawei product IDs into the
USB driver. Then it can support more Huawei data card devices. So to declare
the unusual device for new Huawei data card devices in unusual_devs.h and to
declare more new product IDs in option.c.
To modify the data value and length in the function of
usb_stor_huawei_e220_init in initializers.c That's because based on the USB
standard, while sending SET_FETURE_D to the device, it requires the
corresponding data to be zero, and its sending length also must be zero. In
our old solution, it can be compatible with our WCDMA data card devices, but
can not support our CDMA data card devices. But in this new solution, it can
be compatible with all of our data card devices.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The AnyData ADU-310 series of wireless modems uses the same product ID as the ADU-E100 series.
Signed-off-by: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves dbg calls to dev_dbg where possible. It also fixes some
issues with a previous submission aiming to do the same thing.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Oceanic PID to ftdi_sio driver
Oceanic dive computers (such as the VT3 --
http://www.oceanicworldwide.com/p_computers_vt3.html) all use an onboard
FTDI serial converter, with the FTDI vid and a PID of 0xf460. The
attached patch adds that pid to ftdi_sio; driver connects to my VT3
after that.
Signed-off-by: Vladimir Vukicevic <vladimir@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate device ids which are now supported by drivers/usb/net/hso.c
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kref in the USB serial drivers so that we don't free tty structures
from under the URB receive handlers as has historically been the case if
you were unlucky. This also gives us a framework for general tty drivers to
use tty_port objects and refcount.
Contains two err->dev_err changes merged together to fix clashes in the
-next tree.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the private check for the termios_initialized for
the pl2303 usb driver. It forced the baud to 9600 on the first call
to pl2303_set_termios()
Based on the tty changes in the 2.6.27 kernel, the termios passed to
the *_set_termios functions is always populated the first time.
This means there is no need to privately initialize the settings the
first time, and doing so will not allow the use of the kernel
parameter "console=ttyUSB0,115200" as an example.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some reason the oti6858 driver undefines and redefines the dbg
macro. This makes it spew debugging messages at KERN_INFO instead of
KERN_DEBUG.
This patch removes the undef and define making the driver log like every
other USB serial driver.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While making some other changes to ti_usb_3410_5052, I noticed that the
changes made to move the firmware loading to a separate function are
broken (in ti_download_firmware(), status is set to -ENOMEM and never
changed). This means the driver will never initialize the device
properly. It looks like status was supposed to get the result of
ti_do_download().
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This hardware needs the pl2303 hack in order to work properly :(
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was trying to figure out why my device wasn't supported by the
drivers/usb/serial/sierra.c driver, while looking throught the device
IDs I spotted what I believe to be a typo in the device IDs. Please
apply the following patch
If you look down further, there is another HP wireless broadband card,
which has a vendor ID of 03f0, like my device. Below is my "lsusb -v
-d 03f0:1b1d".
Bus 001 Device 005: ID 03f0:1b1d Hewlett-Packard
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x03f0 Hewlett-Packard
idProduct 0x1b1d
bcdDevice 0.01
iManufacturer 1 HP
iProduct 2 HP ev2200 1xEV-DO Broadband Wireless Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 7
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 3 Data Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 128
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
From: Tony Murray <murraytony@gmail.com>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds devices to the sierra driver and rev's the driver version.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hw interface drivers for the usb serial devices deference the tty
structure to set up the parameters for the initial console. The tty
structure should be passed as a parameter to the set_termios() call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch support NTT DoCoMo A2502 3G/HSDPA modem on option driver.
It is produced by AnyDATA Corp. and also sold as KT Freetelecom (Korea) ADU 620UW.
It support 3.6Mbps/7.2Mbps hight speed communication.
I have tested A2502 with NTT DoCoMo MoperaU ISP service.
Signed-off-by: Hiroshi Miura <miurahr@nttdata.co.jp>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These drivers should not be relying on CONFIG_USB_DEBUG. By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the Product ID for the BandLuxe C150/C250 3.5G data
card series from BandRich Inc.
After detection, the data card works fine.
It was patched against kernel 2.6.27-rc1 with -mm patch
Signed-off-by: Leon Leong <upleong@bandrich.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.
Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: Lex V. Ross <lross@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Moves responsbility of TRU-Install (i.e. ZeroCD) to the usb-storage
driver. See patch 04/04 of this set.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the method by which the number of ports per interface is
assigned so that it is more dynamic and calculated on the fly (as opposed to
hard coding it). This will allow for faster and easier addition of products.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Very minor changes to clean up sierra code. Adds a prefix to debug messages so
that Sierra messages are easily recognized. Removes extraneous code.
This targets kernel 2.6.26-rc9
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB ID 4348:5523 is handled by the ch341 driver. Remove it from the
pl2023 driver.
Reverts 002e8f2c80.
Signed-off-by: Tollef Fog Heen <tfheen@err.no>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1121) fixes a bug in the USB serial core. When a device
is unregistered, the core will give back its minors -- even if the
device hasn't been assigned any!
The patch reserves the highest minor value (255) to mean that no minor
was assigned. It also removes some dead code and does a small style
fixup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Patch adds support for Luminance Stellaris Evaluation/Development
Kits (FTDI 2232C based).
The PIDs were missing.
Successfully tested with a Stellaris LM3S8962 Evaluation kit.
Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the ELV HS485 USB adapter (www.elv.de) to
their home automation bus system. Applies to 2.6.26.
Signed-off-by: Andre Schenk <andre@melior.s.bawue.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The fix NULLed a pointer without freeing it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Juha Motorsportcom <juha_motorsportcom@luukku.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Rothwell points out that this file got deleted (on purpose) by
commit 640c1bce86 ("USB: delete airprime
driver"), but then almost immediately incorrectly resurrected by commit
95da310e66 ("usb_serial: API all change").
Delete it again. If it comes back, we'll need to drive a stake through
its heart.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hardware needs to do break handling itself and may have partial
support only. Make break_ctl return an error code. Add a tty driver flag
so you can indicate driver hardware side break support.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
