Setting fw_cmd_doorbell allows FW command to be queued using posted
writes instead of requiring polling on a "go" bit, so it should be a
performance boost. However, the option causes problems with at least
some device/firmware combinations, so set the default to 0 until we
understand what's going on better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Calls to set_irq_info in set_irq_affinity_info() is redundant because
irq_affinity mask was set just one line immediately above it. Remove
that duplicate call.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When CONFIG_PCI_MSI is set, move_irq() is an empty function, causing
grief when sys admin tries to bind interrupt to CPU.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
'oobavail' parameter of mtd_info structure is now propagated to the MTD
partitions
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
From: "Angelo P. Castellani" <angelo.castellani+lkml@gmail.com>
Using NewReno, if a sk_buff is timed out and is accounted as lost_out,
it should also be removed from the sacked_out.
This is necessary because recovery using NewReno fast retransmit could
take up to a lot RTTs and the sk_buff RTO can expire without actually
being really lost.
left_out = sacked_out + lost_out
in_flight = packets_out - left_out + retrans_out
Using NewReno without this patch, on very large network losses,
left_out becames bigger than packets_out + retrans_out (!!).
For this reason unsigned integer in_flight overflows to 2^32 - something.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows for much better abstraction and separation of the XIP and
non-XIP cases with their own specific implementations. This fixes the
case where a timeout was tripped on in the XIP case by the code that
was meant for the non-XIP case only.
This also makes for a nice code reduction.
Signed-off-by: Nicolas Pitre <nico@cam.org>
CC: "Alexey, Korolev" <alexey.korolev@intel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes a potential starvation issue that can arise when
there is contention on a chip during a period when a process is
currently writing to it. The starvation is avoided by conditionally
rescheduling when the chip is left in a state usable by other processes.
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Tom Gall <tom_gall@vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch removes the unused EXPORT_SYMBOL(tr_source_route).
(Note, the usage in net/llc/llc_output.c can't be modular.)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting BE16 to int and back may or may not work. Correct, to be sure.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] arch/arm/kernel/dma-isa.c: named initializers
[ARM] 3527/1: MPCore Boot Lockup Fix
[ARM] arch/arm/kernel/process.c: Fix warning
[ARM] 3526/1: ioremap should use vunmap instead of vfree on ARM
[ARM] 3524/1: ARM EABI: more 64-bit aligned stack fixes
[ARM] 3517/1: move definition of PROC_INFO_SZ from procinfo.h to asm-offsets.h
A single caller passes __u32. Inside function "net" is compared with
__u32 (__be32 really, just wasn't annotated).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to pack at least the jint16_t structure, because otherwise it'll
be four bytes in size. Thankfully, we can do that and _not_ pack the
actual node structures, and the compiler still doesn't emit stupid code.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is a potential jiffy wraparound bug in the transmit watchdog
that is easily avoided by using time_after().
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes two problems triggered by the MMC stack updating clocks:
- SPI masters driver should accept a max clock speed of zero; that's one
convention for marking idle devices. (Presumably that helps controllers
that don't autogate clocks to "off" when not in use.)
- There are more than 1000 nanoseconds per millisecond; setting the clock
down to 125 KHz now works properly.
Showing once again that Zero (http://en.wikipedia.org/wiki/Zero) is still
an inexhaustible number of bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix two outstanding issues with the pxa2xx_spi driver:
1) Bad cast in the function u32_writer. Thanks to Henrik Bechmann
2) Adds support for per transfer changes to speed and bits per word
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to be able to have a "SPI bus 0" matching chip numbering; but
that number was wrongly used to flag dynamic allocation of a bus number.
This patch resolves that issue; now negative numbers trigger dynamic alloc.
It also updates the how-to-write-a-controller-driver overview to mention
this stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add spi_device hook for LSB-first word encoding, and update all the
(in-tree) controller drivers to reject such devices. Eventually,
some controller drivers will be updated to support lsb-first encodings
on the wire; no current drivers need this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renamed bitbang_transfer_setup to follow convention of other exported symbols
from spi-bitbang. Exported spi_bitbang_setup_transfer to allow users of
spi-bitbang to use the function in their own setup_transfer.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that spi_write_then_read() can always handle at least 32 bytes
of transfer (total, both directions), minimizing one portability issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes superfluous whitespace in the <linux/spi/spi.h> header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary). The driver has the following
features:
- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some protocols (like one for some bitmap displays) require different clock
speed or word size settings for each transfer in an SPI message. This adds
those parameters to struct spi_transfer. They are to be used when they are
nonzero; otherwise the defaults from spi_device are to be used.
The patch also adds a setup_transfer callback to spi_bitbang, uses it for
messages that use those overrides, and implements it so that the pure
bitbanging code can help resolve any questions about how it should work.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts struct dma_resources to named initializers.
Besides fixing a compile error in -mm, it didn't sound like a bad idea.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On AMD Au1550 the static bus controller fails to keep -CE asserted during
chip ready delay on read commands and the NAND chip being used requires this.
So, the current driver allows nand_base.c to drive -CE manually during the
entire sector read. When the PCMCIA driver is enabled however, occasionally
the ECC errors occur on NAND reads. This happens because the PCMCIA driver
polls sockets periodically and reads one of the board's control/status regs
(BCSRs) which are on the same static bus as the NAND flash, and just use
another chip select (and the NOR flash also resides on that bus), so as the
NAND driver forces NAND chip select asserted and the -RE signal is shared, a
contention occurs on the static bus when BCSR or NOR flash is read while we're
reading from NAND.
So, we either can't keep interrupts enabled during the whole NAND sector
read (which is hardly acceptable), or have to implement some interlocking
scheme between multiple drivers (which is painful, and makes me shudder :-).
There's a third way which has proven to work: to force -CE asserted only
while we're waiting for a NAND chip to become ready after a read command,
disabling interrupts for a maximum of 25 microseconds (according to Toshiba
TC58DVM92A1FT00 datasheet -- this chip is mentioned in the board schematics);
for Samsung NAND chip which seems to be actually used this delay is even less,
12 us.
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix build warnings from drivers/mtd/redboot.c due to
use of `unsigned long` in `struct fis_image_desc` for
fields being passed to swab32s() which expects __u32 *
Change the entries to uint32_t to make them compatible
with the swab32s() function
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
During the last cleanup of the AMD Au1550 NAND driver the old buglet was
reintroduced: as the MEM_STNDCTL register is write-only and seem to always
read as 0x31, read-modify-write to it done in au1xxx_nand_init() will have the
side effect of enabling -RCS0/1 pin override (via bits 4/5 of this reg.), thus
possibly causing a contention on the static bus when the NOR flash (using
-RCS0) or board control status registers (using -RCS2) are read. Luckily, this
goes away with a first NAND access, since au1550_hwcontrol() doesn't try to
read this register before writing anymore.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
fs/jffs2/summary.c: In function ‘jffs2_sum_write_data’:
fs/jffs2/summary.c:658: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 4 has type ‘uint32_t’
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Patch from Harry Fearnhamm
This patch fixes the occasional lockup seen in early boot stage
on RealView MPCore system.
Signed-off-by: Harry Fearnhamm <Harry.Fearnhamm@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] Fix pSeries identification in prom_init.c
[PATCH] powerpc: fix kernel version display on pseries boxes
With CONFIG_NUMA set, kmem_cache_destroy() may fail and say "Can't
free all objects." The problem is caused by sequences such as the
following (suppose we are on a NUMA machine with two nodes, 0 and 1):
* Allocate an object from cache on node 0.
* Free the object on node 1. The object is put into node 1's alien
array_cache for node 0.
* Call kmem_cache_destroy(), which ultimately ends up in __cache_shrink().
* __cache_shrink() does drain_cpu_caches(), which loops through all nodes.
For each node it drains the shared array_cache and then handles the
alien array_cache for the other node.
However this means that node 0's shared array_cache will be drained,
and then node 1 will move the contents of its alien[0] array_cache
into that same shared array_cache. node 0's shared array_cache is
never looked at again, so the objects left there will appear to be in
use when __cache_shrink() calls __node_shrink() for node 0. So
__node_shrink() will return 1 and kmem_cache_destroy() will fail.
This patch fixes this by having drain_cpu_caches() do
drain_alien_cache() on every node before it does drain_array() on the
nodes' shared array_caches.
The problem was originally reported by Or Gerlitz <ogerlitz@voltaire.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extends an earlier patch from John Blackwood to more exception handlers
that also run on the exception stacks.
Expand the use of preempt_conditional_{sti,cli} to all cases where
interrupts are to be re-enabled during exception handling while running
on an IST stack.
Based on original patch from Jan Beulich.
Cc: John Blackwood <john.blackwood@ccur.com>
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes some boot failures on Dell and Unisys systems with memory
hotadd added.
- Set hotadd_percent to 0 by default. This means anybody using hotadd
memory needs to specify the value on the command line. That's
because there are lots of Intel boxes which have a bogus hotplug area
in their SRAT and they would waste a lot of memory before.
- Fix calculation of how much memory to use when the hotplug area
exceeds hotadd_percent
- Fix fallback when the
- Fix fallback if memory hotadd is not compiled in.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed to see all devices.
The system has multiple PCI segments and we don't handle that properly
yet in PCI and ACPI. Short term before this is fixed blacklist it to
pci=noacpi.
Acked-by: len.brown@intel.com
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This triggers for b44's 1GB DMA workaround which tries to map
first and then bounces.
The 32bit heuristic is reasonable because the IOMMU doesn't attempt
to handle < 32bit masks anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We all inherited the same error from the original NAND board driver which
got copied and changed. Fix them all at once...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On Mon, May 15, 2006 at 12:56:37AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.17-rc3-mm1:
>...
> git-mtd.patch
>...
> git trees
>...
If we correct the names of the config options, the code might actually
work as intended...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The OF trampoline code prom_init.c still needs to identify IBM pSeries
(PAPR) machines in order to run some platform specific code on them like
instanciating the TCE tables. The code doing that detection was changed
recently in 2.6.17 early stages but was done slightly incorrectly. It
should be testing for an exact match of "chrp" and it currently tests
for anything that begins with "chrp". That means it will incorrectly
match with platforms using Maple-like device-trees and have open
firmware. This fixes it by using strcmp instead of strncmp to match what
the actual platform detection code does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We are displaying the wrong thing on the operator panel (2x40
character LCD). This got broken in commit cebb21b5, when UTS_RELEASE
got changed to system_utsname.version.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
