Make the sonixb driver handle pas106 and pas202 cameras, when both it
and the sn9c102 driver are enabled in the kernel configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixup brightness ctrl and add gain and exposure ctrls for PAS106B sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In 640x480, if the reg11 has less than 4, the image is
unstable (the bridge goes into a higher compression mode
which we have not reverse engineered yet).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixup brightness ctrl and add gain and exposure ctrls for PAS202BCB sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some sensors only allow controlling the exposure by changing the clockdiv,
which means that exposure takes pretty large jumps (for example when going
from a div of 1 to 2, the exposure doubles). Use 2 different entries in
the controls array for these 2 different types of exposure (always
disabling one), and;
Add a new autogain algorithm for the coarse exposure case, which normally
changes the gain setting, only touching the exposure setting if the desired
luminance cannot be reached with gain, and after an exposure change once more
first tries gain, etc. Thus avoiding exposure changes, and the resulting
oscilation because of the huge steps these exposure controls take.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Leave bridge gain at 1.0 when we have a sensor gain, while at it also
change the bridge gain setting code to write both registers in one go
saving us a usb transaction.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixb: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our hstart value was wrong for tas5110d sensor using sonixb cams, this
patch fixes this. Many thanks to Paulus (laudaka) for donating me a camera
with such a sensor IC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ctrls field of struct sd_desc is declared as const
in gspca.h. It is worth to initialize the content also with
constant values.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (345 commits)
V4L/DVB (13542): ir-keytable: Allow dynamic table change
V4L/DVB (13541): atbm8830: replace 64-bit division and floating point usage
V4L/DVB (13540): ir-common: Cleanup get key evdev code
V4L/DVB (13539): ir-common: add __func__ for debug messages
V4L/DVB (13538): ir-common: Use a dynamic keycode table
V4L/DVB (13537): ir: Prepare the code for dynamic keycode table allocation
V4L/DVB (13536): em28xx: Use the full RC5 code on HVR-950 Remote Controller
V4L/DVB (13535): ir-common: Add a hauppauge new table with the complete RC5 code
V4L/DVB (13534): ir-common: Remove some unused fields/structs
V4L/DVB (13533): ir: use dynamic tables, instead of static ones
V4L/DVB (13532): ir-common: Add infrastructure to use a dynamic keycode table
V4L/DVB (13531): ir-common: rename the debug routine to allow exporting it
V4L/DVB (13458): go7007: subdev conversion
V4L/DVB (13457): s2250: subdev conversion
V4L/DVB (13456): s2250: Change module structure
V4L/DVB (13528): em28xx: add support for em2800 VC211A card
em28xx: don't reduce scale to half size for em2800
em28xx: don't load audio modules when AC97 is mis-detected
em28xx: em2800 chips support max width of 640
V4L/DVB (13523): dvb-bt8xx: fix compile warning
...
Fix up trivial conflicts due to spelling fixes from the trivial tree in
Documentation/video4linux/gspca.txt
drivers/media/video/cx18/cx18-mailbox.h
The number of packets per isochronous message may now be set by the subdrivers
(default value 32).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce int ret and check it value after call to usb_register().
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The transfer endpoint address is now automatically chosen.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to http://bugzilla.kernel.org/show_bug.cgi?id=11920,
the driver sn9c102 does not work for this webcam.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- This patch makes sonixb.c strife to different values during autoexposure
for sif versus vga sensors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix sparse warnings. None are serious, but cutting down on these helps find
future serious sparse warnings/errors.
Redid the av7710.c patch based on a suggestion by Oliver Endriss.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Adjust hstart in ov7630 on sn9c103 initdata to shift bayer pattern, this is
the same change as done for the other initdata tables in a previous patch.
- Assign usb-id's for the ov7630 + sn9c103 to gspca if gspca and sn9c102
drivers are both enabled.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When using the sonixb driver in a dark room and given that the autoexposure
algorithm starts with a setting most suitable for daylight, the picture
produced by the cam may actually be 100% black leading to a avg_lum value of 0,
so an avg_lum value of 0 does not always signal an exposure settings change
(which it normally does). This patch adds a check for the really black image
case and stops dropping all frames as invalid in this case.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes gspca claim the USB-ID for sn9c101/2 cams with a TAS5110C1B
sensor even if both gspca and sn9c102 are enabled, as these cams are much
better supported under gspca (and extensively tested with gspca).
It also removes an usb-id from sn9c102 for one more unsupported bridge
sensor combo.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Add documentation for some known registers
- Add support for vga modes (320x240, 160x120) for sif sensors
- Remove F_RAW sensor flag raw mode should work on any sensor as its a bridge
only thing and keeping the flag was becoming awkward.
- Fixup ov6650 and pas106 auto exposure window settings
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1) Lower the hstart setting for all sensor by 1 so that we generate
(compressed) BGGR data just like sn9c102 does (instead of GBRG data)
2) Add support for raw bayer output in the lowest resolutions (not enough
bandwidth for higher resolutions), this should work with all sensors but
to be sure only enable it for sensors where it has been tested.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Under certain conditions sonixb compressed frame size can get bigger then
the uncompressed size (seen with 0c45:6028), so make the buffers slightly
bigger.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-the usb-id table caried several flags which were not usb-id specific but
sensor specific, add a sensor_data array and move these flag there
-fr_h_sz was being abused to store and check which bridge was being used
instead add a bridge member to the sd struct
-now that we have a sensor_data table use that to store pointers to
init_sequences instead of using switch cases on sd->sensor
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-remove USB-id's from zc0301 for cams for which zc0301.c does not support
the sensor
-remove USB-id's from sn9c102 for cams where sn9c102 does not support the
bridge sensor combination
-no longer make inclusion of usb id's removed from zc0301 and sn9c102
conditional in gspca
-fix conditional inclusion of USB-id's in gspca to also work when the
conflicting drivers are build as a module
-add a number of USB-id's to gspca from various windows .inf files:
0c45:608f from generic sonix sn9c103 inf file (+ ov7630 which we support)
041e:4022 from creative webcam nx pro, same as already supported 041e:401e
0ac8:0301 from generic zc0301 driver which supports many sensors
10fd:804d from typhoon webshot driver (also FlyCAM-USB 300 plus)
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The USB buffer may be used for DMA and there may be a caching problem
if the buffer is part of the device structure.
Thanks to Alan Stern.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- new function 'init' called on probe and resume
- remove the functions 'open' and 'closed'
- 'stopN' and 'stop0' are optional
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- turn the led of the cam off after plugging in the cam
- move the probe code from open to config, so that if the probe fails
we never register
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- set some controls as disabled instead of copying the device descr.
- in the ov6650 / 7650 exposure code clamp reg 11 before (instead of after)
using it to calculate reg 10.
- disable brightness (instead of ignoring it) for the TAS5110.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This option is changed to GSPCA_DEBUG and it is set by default in gspca.h.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This fixes a bug introduced in c503a6f8332a (thanks to Hans de Goede).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
gspca_sonixb remove one more no longer needed special case from the code
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
gspca_sonixb remove some no longer needed sn9c103+ov7630 special cases
Signed-off-by: Andoni Zubimendi <andoni.zubimendi@gmail.com>
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
gspca_sonixb remove non working ovXXXX contrast, hue and saturation ctrls
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andoni Zubimendi has been doing some testing with his sn9c103 cam with
ov7630 sensor, and with this patch the exposure setting and autoexposure now
work.
This patch also removes some special cases in the shared ov6650 / ov7630 code
which now are handled the same for both sensors and it adds a new special case
which stops us from changing the hsync / vsync polarity settings from their
default on the ov7630 (which we were doing as a side-effect of using the ov6650
exposure code for the ov7630).
Last this patch removes the superficial difference between the OV7630 and
OV7630_3 sensors.
Signed-off-by: Andoni Zubimendi <andoni.zubimendi@gmail.com>
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The sn9c102 driver claims to support usb-ID 0x0c45:0x6011, which is
a sn9c102 with ov6650 sensor, but the sn9c102 driver does not support the
ov6650 sensor (tested). Also the sn9c102 driver claims to support usb-ID
0x0c45:0x603f, which is a sn9c102 with CISVF10 sensor, but the sn9c102
driver does not support the CISVF10 sensor (not tested).
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
(does not work with ov6650)
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
