In the unlikely event that e1e_wphy() returns an error, the returned error
code is not propogated to the caller of e1000_set_d3_lplu_state_ich8lan().
With this change, there is a rare possibility that ret_val might not get
set so it must be initialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These are a few instances of returning a value that can only be 0 so just
use a 'return 0' to make it more obvious.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just return the appropriate value.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unlikely event that e1000e_setup_copper_link() returns an error,
the returned error code value is not propogated to the caller of
e1000_setup_copper_link_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unlikely event that e1e_wphy() returns an error, the returned error
code value is not propogated to the caller of
e1000_cfg_kmrn_10_100_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the following functions, rename the generic 'out' goto label to the more
descriptive 'release' to indicate the type of common work that is done
before exiting the functions. No functional change, cosmetic only.
e1000_sw_lcd_config_ich8lan()
e1000_oem_bits_config_ich8lan()
e1000_init_phy_wakeup()
e1000e_write_phy_reg_bm()
e1000e_read_phy_reg_bm()
e1000e_read_phy_reg_bm2()
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two exit points of e1000e_write_nvm_spi() which require the
nvm->ops.release() function pointer called just before exiting.
Consolidate the two duplicate pieces of common work with a goto. With
this change, the value ret_val will need to be returned instead of 0.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000_init_mac_params_XXX() functions (where XXX is one of the three
MAC-family types 80003es2lan, 82571 and ich8lan) was not meant to require a
pointer to the adapter struct but does require a pointer to the hw struct.
Pass that pointer in to the functions instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
v2 - replaced mac->autoneg_failed == false with !mac->autoneg_failed
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...and convert some goto's which simply return to just return.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
warning: comparison of unsigned expression < 0 is always false
Remove an unnecessary test that is reported when compiling driver with W=1.
The test is unnecessary because Intel wired GbE hardware older (i.e. less)
than 82571 is not supported by this driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup of some whitespace and indentation of a single code block.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WARNING: min() should probably be min_t(unsigned int, 4, skb->data_len)
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the existing hw pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine two switch statements into one, convert a nebulous pointer to one
that is a bit more in keeping with the rest of the driver code and cleanup
some coding style. No change in functionality, just cosmetic changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine two switch statements into one, convert a nebulous pointer to one
that is a bit more in keeping with the rest of the driver code and remove
some dead code (there are no 80003es2lan devices with fiber). No change in
functionality, just cosmetic changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The majority of the e1000e code checks most function return values using a
test like 'if (ret_val)' or 'if (!ret_val)' but there are a few instances
of 'if (ret_val == 0)'. This patch converts the latter to the former for
consistency.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
warning: missing initializer
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The generic lib.c file contains code relative to the various MACs, NVM and
Manageability supported by the driver. This patch splits the file into
three which are specific to those areas similar to how the PHY-specific
code is in phy.c and code specific to the 80003es2lan, 8257x, and ichX
MAC families are in their own files. The generic code that is applicable
to all MAC/PHY parts supported by the driver remains in netdev.c, param.c
and ethtool.c files. No change in functionality, just moving code
around for ease of maintenance, with some whitespace and other checkpatch
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
__er16flash() is not meant to be called directly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert the last instances of strncpy() to the preferred strlcpy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.
Also, add '\n' and remove unnecessary '\r' from a few debug strings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting the Low Power Link Up (LPLU, a.k.a. reverse auto-negotiation)
on 82577/8278/82579, do not restart auto-negotiation if reset of the Phy is
blocked by the Manageability Engine.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During bi-directional stress on some 82566/82567 devices, some received
packets were dropped. Increasing the Receive Packet Buffer Allocation
resolves this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When going to Sx with an ICHx/PCH device, the default Low Power Link Up
(LPLU, a.k.a. reverse auto-negotiation) behavior should be whatever is set
in the NVM. However, the function e1000_suspend_workarounds_ich8lan()
called when going to Sx always enabled LPLU in all power states.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The workaround which toggles the LANPHYPC (LAN PHY Power Control) value bit
to force the MAC-Phy interconnect into PCIe mode from SMBus mode during
driver load and resume should always be done except if PHY resets are
blocked by the Manageability Engine (ME). Previously, the toggle was done
only if PHY resets are blocked and the ME was disabled.
The rest of the patch is just indentation changes as a consequence of the
updated workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Otherwise (on sparc64):
drivers/net/ethernet/intel/e1000e/ethtool.c:657:3: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82574/82583, there is a hardware bug which might cause a Tx hang when
the internal buffer is full. Setting this bit enables a hardware fix to
work around the issue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the default hardware values for TIPG except for 80003es2lan(*). The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs). The only change in
functionality is setting the correct default TIPG for the latter devices.
(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When connected to certain switches, the 82579 PHY might drop link
unexpectedly. Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a patch from Prabhakar Kushwaha <prabhakar@freescale.com>, set
appropriate default interrupt mode dependent on whether CONFIG_PCI_MSI
is enabled in the kernel configuration and if the hardware supports
MSI-X. Set the module parameter log message accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make it more like how igb does it, with some additional error checking.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations. Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable RPS by default. Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.
v2: added ethtool command to query flow hashing behavior per Ben Hutchings
and changed the type of rsskey to cleanup the setting of the register
array and avoid unnecessary casts (as pointed out by Joe Perches).
The long error messages are not changed since there is nothing in
the kernel ./Documentation that suggests the preferred method for
dealing with long messages other than to never break strings; leaving
them as-is for now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
e1000_rx_checksum() instead of in each call to the function
v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch from Mike McElroy created against the out-of-tree e1000e
driver:
Hitting the BUG_ON in napi_enable(). Code inspection shows that this can
only be triggered by calling napi_enable() twice without an intervening
napi_disable().
I saw the following sequence of events in the stack trace:
1) We simulated a cable pull using an Extreme switch.
2) e1000_tx_timeout() was entered.
3) e1000_reset_task() was called. Saw the message from e_err() in the
console log.
4) e1000_reinit_locked was called. This function calls e1000_down() and
e1000_up(). These functions call napi_disable() and napi_enable()
respectively.
5) Then on another thread, a monitor task saw carrier was down and executed
'ip set link down' and 'ip set link up' commands.
6) Saw the '_E1000_RESETTING'warning fron the e1000_close function.
7) Either the e1000_open() executed between the e1000_down() and e1000_up()
calls in step 4 or the e1000_open() call executed after the e1000_up()
call. In either case, napi_enable() is called twice which triggers the
BUG_ON.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Mike McElroy <mike.mcelroy@stratus.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch submitted my Michael Wang
<wangyun@linux.vnet.ibm.com>.
Descriptors may not be write-back while checking TX hang with flag
FLAG2_DMA_BURST on.
So when we detect hang, we just flush the descriptor and detect
again for once.
-v2 change 1 to true and 0 to false and remove extra ()
CC: Michael Wang <wangyun@linux.vnet.ibm.com>
CC: Flavio Leitner <fbl@redhat.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
