Actually clfe and surround DACs are inverted in alc883_dac_nids array
(see ALC883 datasheet). I discovered this while testing multi-channel
setup (using 3stack-6ch-dig model) on MSI 945GCM5 V2 motherboard that
has an ALC883 codec. Simply Rear Left/Right and Center/LFE were swapped
in 6 channel mode (also in 4 channel mode you didn't get rear left/right
output). Other models also were affected by this bug, as can be seen by
the mixer layouts that "workaround" this (the real bug was not noticed,
and some other models simply played with mixer and initial verbs). Thus
along with fixing the order of dac nids, also change the models that
relied on previous dac ordering properly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable is_capture is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* removing the hack with NON_AKM ak4xxx type
* support for card-specific flags in ak4114_stats
* definition of the flags for corresponding cards
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AK4114 on Juli@ has the SPDIF input sample rate detection and
causes errors when an incompatible sample rate is chosen.
The patch adds the open hook to check the current rate and limit
the hw constraints.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station headphone output had no audio and jack sense
was not considered.
Jack information from the laptop itself and the dock are combined, as
the dock does not obscure the connector.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hda-intel driver has a problem at power-off on ASUS P5AD2.
It's caused when the position-buffer is enabled -- most likely a
hardware-specific problem.
This patch adds a quirk to avoid the unnecessary enablement of
position-buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Map 3stack-6ch-dig ALC662 model for Asus P5GC-MX.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently ALC662 doesn't suport amp mute for AmpOut in nids 0x02, 0x03,
0x04 (see block diagram in ALC662 datasheet page 3, does M correspond to
mute?). The result is that currently mute for "Front Playback Switch",
"Surround Playback Switch", "Center Playback Switch" and "LFE Playback
Switch" mixer items doesn't work (tested on Asus P5GC-MX motherboard
with 3stack-6ch model).
The solution I found for this is to mute the proper inputs in 0x0c,
0x0d, 0x0e audio mixers.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the headphone controls are created as Master wrongly in
some cases, and this prevents the virtual master controls.
The patch fixes the problem by simply using "Headphone" always for
headphone controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed issue on some laptops that if the Master mixer and DAC mixers are
turned all the way up that will cause distortion. This is fixed by limiting
the max volume with the volume knob nid.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Improved ALC262 ultra model for Samsung Q1 Ultra series.
- clean up mixers
- support of input from HP jack as a mic
- add quirk for Q1 EL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
aw2-tsl.h should be rather a C file to be included since it's referred
only in aw2-saa6146.c and includes a table data.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default capture source should be the mic which is 0x01 on this model.
In addition to that the change to VREF50 allows for higher capture volume.
Signed-off-by: Michael Gruber <lists.mg@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Changed so that internal speakers point to the Front mixer instead of Surround.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the Toshiba Equium L30 laptop and renames the mixer
controls to match Laptop usages.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the internal mic as a capture source item for ALC268 acer model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the Device IDs of nvidia MCP79 HD audio controller to hda_intel.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the model laptop-hpsense use the 0x12 as ExtMic,
and use 0x14 as Internal IntMic.
But the hp530 only have one ExtMic, the Pin widget is 0x14.
In this patch, I changed the mixer item for them.
I still reserved the IntMic item, it will be helpful if
other machine may use this model.
ALSA bug#3821.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for Pi2515.
This model is to support it. ALSA bug#3800.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NEC S970 has no sound in the internal speakers when autodetection is
used.
With targa-dig model, there is sound in the speakers and it gets
correctly muted when pluging headphones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for M720R (ALSA bug#3781).
This patch is to support HP jack-sensing and mixer.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sparc32:
sound/pci/hda/hda_intel.c: In function 'azx_create':
sound/pci/hda/hda_intel.c:1838: error: 'DMA_64BIT_MASK' undeclared (first use in this function)
sound/pci/hda/hda_intel.c:1838: error: (Each undeclared identifier is reported only once
sound/pci/hda/hda_intel.c:1838: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added core_init[] for several 92hd73xxx laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power management can't be enabled on fixed ports, since the presence
will always return false and prevent output.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the array declaration to hda_codec.c where it is used and add includes
where the individual presets are declared.
Fixes the following sparse warnings:
sound/pci/hda/patch_realtek.c:13744:25: warning: symbol 'snd_hda_preset_realtek' was not declared. Should it be static?
sound/pci/hda/patch_cmedia.c:729:25: warning: symbol 'snd_hda_preset_cmedia' was not declared. Should it be static?
sound/pci/hda/patch_analog.c:3656:25: warning: symbol 'snd_hda_preset_analog' was not declared. Should it be static?
sound/pci/hda/patch_sigmatel.c:3995:25: warning: symbol 'snd_hda_preset_sigmatel' was not declared. Should it be static?
sound/pci/hda/patch_si3054.c:286:25: warning: symbol 'snd_hda_preset_si3054' was not declared. Should it be static?
sound/pci/hda/patch_atihdmi.c:156:25: warning: symbol 'snd_hda_preset_atihdmi' was not declared. Should it be static?
sound/pci/hda/patch_conexant.c:1721:25: warning: symbol 'snd_hda_preset_conexant' was not declared. Should it be static?
sound/pci/hda/patch_via.c:1962:25: warning: symbol 'snd_hda_preset_via' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Temp variable in the loop shadows the second argument (which is otherwise
unused in this function). Change this to defcfg as it is used to hold
the default config.
sound/pci/hda/patch_sigmatel.c:2759:18: warning: symbol 'cfg' shadows an earlier one
sound/pci/hda/patch_sigmatel.c:2734:26: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In both cases we are passing around the substream number, use
sub_num for this.
sound/pci/riptide/riptide.c:1633:6: warning: symbol 'index' shadows an earlier one
sound/pci/riptide/riptide.c:121:12: originally declared here
sound/pci/riptide/riptide.c:1673:6: warning: symbol 'index' shadows an earlier one
sound/pci/riptide/riptide.c:121:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Inner loop redeclares err with u32 rather than int, stupid fix here
is to change the inner err to err2.
sound/pci/pcxhr/pcxhr_core.c:1008:8: warning: symbol 'err' shadows an earlier one
sound/pci/pcxhr/pcxhr_core.c:983:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use priv_idx as an identifier.
sound/pci/oxygen/virtuoso.c:277:15: warning: symbol 'index' shadows an earlier one
sound/pci/oxygen/virtuoso.c:56:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In all four case, adding a private value to the iooff index,
call it priv_idx.
sound/pci/ice1712/ice1712.c:1300:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1312:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1338:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1350:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
[tiwai - fixed coding issues as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
enable in these contexts refers specifically to intr enable, as
per the two functions it is found in. Use intr_enable instead.
sound/pci/emu10k1/emu10k1x.c:330:15: warning: symbol 'enable' shadows an earlier one
sound/pci/emu10k1/emu10k1x.c:53:12: originally declared here
sound/pci/emu10k1/emu10k1x.c:341:15: warning: symbol 'enable' shadows an earlier one
sound/pci/emu10k1/emu10k1x.c:53:12: originally declared here
instead of shadowing, use cap_voice as we test for the capture
voice in this statement.
sound/pci/emu10k1/emu10k1x.c:798:25: warning: symbol 'pvoice' shadows an earlier one
sound/pci/emu10k1/emu10k1x.c:787:24: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reading regs from the fpga into an int instead of a u32, trivial
fix.
sound/pci/emu10k1/emuproc.c:422:34: warning: incorrect type in argument 3 (different signedness)
sound/pci/emu10k1/emuproc.c:422:34: expected unsigned int [usertype] *value
sound/pci/emu10k1/emuproc.c:422:34: got int *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/au88x0/au88x0_pcm.c:508:15: warning: Using plain integer as NULL pointer
Also some small codingstyle fixes.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the variable err to _err within the ADD_CTLS macro to avoid
shadowing the local variable.
sound/pci/ca0106/ca0106_mixer.c:710:2: warning: symbol 'err' shadows an earlier one
sound/pci/ca0106/ca0106_mixer.c:663:6: originally declared here
sound/pci/ca0106/ca0106_mixer.c:712:3: warning: symbol 'err' shadows an earlier one
sound/pci/ca0106/ca0106_mixer.c:663:6: originally declared here
sound/pci/ca0106/ca0106_mixer.c:721:3: warning: symbol 'err' shadows an earlier one
sound/pci/ca0106/ca0106_mixer.c:663:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
change to intr_enable as per the two functions it is defined in.
sound/pci/ca0106/ca0106_main.c:438:15: warning: symbol 'enable' shadows an earlier one
sound/pci/ca0106/ca0106_main.c:159:12: originally declared here
sound/pci/ca0106/ca0106_main.c:449:15: warning: symbol 'enable' shadows an earlier one
sound/pci/ca0106/ca0106_main.c:159:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
enable is used to test for whether or not spdif should be enabled,
change to spdif_enable.
sound/pci/ali5451/ali5451.c:1812:15: warning: symbol 'enable' shadows an earlier one
sound/pci/ali5451/ali5451.c:63:12: originally declared here
sound/pci/ali5451/ali5451.c:1840:27: warning: symbol 'enable' shadows an earlier one
sound/pci/ali5451/ali5451.c:63:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
err is always assigned before it is used, no need to declare another
inside the if statement.
sound/pci/ac97/ac97_pcm.c:577:7: warning: symbol 'err' shadows an earlier one
sound/pci/ac97/ac97_pcm.c:572:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kernel style does assignment outside of if() block
sound/pci/rme96.c:1562:71: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kernel style does assignment outside of if() statements.
sound/pci/rme32.c:1353:71: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
change id to elem_id as it is used to initialize each mixer element
sound/pci/maestro3.c:2071:25: warning: symbol 'id' shadows an earlier one
sound/pci/maestro3.c:67:13: originally declared here
index is used in each of these places to count over the dsp's memory,
change to the name dsp_index
sound/pci/maestro3.c:2572:9: warning: symbol 'index' shadows an earlier one
sound/pci/maestro3.c:66:12: originally declared here
sound/pci/maestro3.c:2604:9: warning: symbol 'index' shadows an earlier one
sound/pci/maestro3.c:66:12: originally declared here
[tiwai - fixed coding style issues as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
id was only used as a counter in a for loop, move the declaration
to where it is used and change it to i.
sound/pci/fm801.c:1288:6: warning: symbol 'id' shadows an earlier one
sound/pci/fm801.c:51:13: originally declared here
[tiwai - fixed a coding style issue as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
id is used when initializing the mixer elements, use elem_id here
instead.
sound/pci/es1968.c:1963:25: warning: symbol 'id' shadows an earlier one
sound/pci/es1968.c:129:13: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
index is incremented only when AC97_EI_SPDIF and then assigned to
the index field. Change the temporary name to is_spdif.
sound/pci/ens1370.c:1638:10: warning: symbol 'index' shadows an earlier one
sound/pci/ens1370.c:84:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A temporary variable for each mixer element is used in an initialization
loop, use the name elem_id.
sound/pci/cmipci.c:2747:26: warning: symbol 'id' shadows an earlier one
sound/pci/cmipci.c:56:13: originally declared here
[tiwai - fixed a coding style issue as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bits indicating SPDIF frequency in the status register are not the same for
the 9632 than for the other cards, because it also supports 192kHz. A specific
bitmask has thus been added (used in hdsp_spdif_sample_rate()).
The 9632 does not seem to report external sample rates greater than 96kHz. In
this case, the best seems to report spdif rate when autosync reference is
spdif. This also required to move function hdsp_spdif_sample_rate().
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added logic to check if AUTO_PIN_FRONT_MIC is available for output
switch, if AUTO_PIN_MIC isn't.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops have a internal analog microphone that is not setup by the BIOS.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added PCI_QUIRKS for laptop that have the 92HDxxx family of codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC_DELL_BIOS quirks were setting the association value wrong
for port 0x0f, which prevented it from being included in hp_outs[].
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix issue on STAC927x codecs that first DAC was getting powered down
even if was being used.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the capture source properly for auto model.
It's especially important for cases that only mic is detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the beep volume control to ALC268 codec support code.
Since the codec doesn't return the correct AMP caps, we need to override
the value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a private array for TLV entries of virtual master controls instead
of (supposed) static array. This cleans up the existing codes.
Also, now vmaster assumes the simple dB-range TLV that is the only type
it can handle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the codes for virtual master controls to sound core part so that
not only hda-intel drivers can use it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of 8 channel sound for codecs that are known to work.
So far, only ALC850 is marked as a 8ch-support codec.
This fix is a modified version of the patch on ALSA BTS#2097 by
Martin Ellis:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=2097
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of new AD codecs: AD1883, AD1884A, AD1984A and AD1984B.
These are almost compatible except for additional digital pins, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC262 must have capsrc_nids defined as well as in ALC882.
Also, add a NULL check in alc882_mux_enum_put to avoid Oops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last patch for fixing the auto-config pin setting breaks the resume
due to a wrong use of snd_hda_codec_amp_stereo(). The code in the init
hook shouldn't touch the amp cache.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new mixer switch to enable/disable the sharing of the default
PCM stream with analog and SPDIF outputs. When "IEC958 Default PCM"
switch is on, the PCM stream is routed both to analog and SPDIF outputs.
This is the behavior in the earlier version.
Turning this switch off has a merit for some codecs, though. Some codec
chips don't support 24bit formats for SPDIF but only for analog outputs.
In this case, you can use 24bit format by disabling this switch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes some bugs in the auto-configurator of Realtek codecs:
- add missing pin set-up for speaker pins
- fix the speaker auto-mute function not to conflict with the existing
"Speaker" mixer switch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In some cases, the BIOS sets up only the HP pins with different assoc
and sequence numbers, e.g. on FSC Esprimo with ALC262.
This patch adds a fix-up for such a case. When multiple HPs are defined
and no line-outs is found, the configurator tries to re-assign some pins
from HP list to line-out, judging from the sequence number.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implemented the auto-mic jack sensing for Samsung laptops with AD1986A
codec chip (model=laptop-eapd).
The hardware uses pin 0x1d and 0x1f for the internal and external
mics, respectively.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up the codes of the capture source selection for Realtek codecs.
Now using common helper functions with the new capsrc_nids field.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reprogram the speaker-pin setting at each HP pin plug to make sure
the spekaer auto-muting on AD1981HD hp model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I've just noticed that there are a handful of duplicate controls in the
ALC268 test model mixer. This patch (against alsa-driver 1.0.16) removes
them.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
See ALSA bug#3327 for more details. Experimental.
Also fix support for M-Audio Delta 1010E - subdevice check.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The HD-audio hardware usually supports 64bit address for DMA and other
buffers. The patch enables the feature if supported.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On several laptops that have STAC9228 codecs have unused DACs,
this powers them down to a D3 state.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes the problems with Midi In on Hoontech/STA dsp24 cards, for example with
DSP2000 box, without restricting the box configurations available. Also adds
mpu_401 name strings.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current scheme, PCM device numbers are assigned incrementally
in the order of codecs. This causes problems when the codec number
is irregular, e.g. codec #0 for HDMI and codec #1 for analog. Then
the HDMI becomes the first PCM, which is picked up as the default
output device. Unfortuantely this doesn't work well with normal
setups.
This patch introduced the fixed device numbers for the PCM types,
namely, analog, SPDIF, HDMI and modem. The PCM devices are assigned
according to the corresponding PCM type. After this patch, HDMI will
be always assigned to PCM #3, SPDIF to PCM #1, and the first analog
to PCM #0, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code doesn't allow multiple SPDIF devices, and causes
errors when multiple SPDIF devices are found (e.g. SPDIF out and HDMI).
This patch allows multiple SPDIF devices by incrementing the index
automatically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the OQO Model 2 Ultra Mobile PC.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
snd_es1968_ac97_read() calls snd_es1968_ac97_wait() first outside a locked
area, and later, while holding a lock.
snd_es1968_ac97_wait() has a polling loop with a cond_resched() inside it..
which sleeps, so the second call is invalid.
This patch adds a version of the wait function that just pure polls. While
this is not very elegant in principle, it's very likely the easiest thing to
do here, we already checked if the chip was ready (while yielding) just
before, so it is very unlikely to take a long time here.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the line-out volume control of eeepc p701 to be a proper slave of
the virtual master control.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't need to declare a struct when defining a structure layout. Both
of these structs are unused.
sound/pci/ice1712/revo.c:39:3: warning: symbol 'revo51' was not declared. Should it be static?
sound/pci/ice1712/phase.c:54:3: warning: symbol 'phase28' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models like eeepc ep20 have invalid mixer names that aren't
handled properly by virtual master controls. Rename them to the
proper names.
Also fixed some typos in the mixer names but they are not compiled
in right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a quirk to the Realtek ALC883 table for the Albatron KI690-AM2
motherboard to use the 6stack-dig model.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot to set the module owner for the HiFier/Xonar models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP dv8000 laptop has a problem with Master volume. It's due to the
connection of the widget 0x13. When it's connected from the analog
amp mixer (0x19), it works as expected mysteriously (ALSA bug#3775):
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3775
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call free_irq() after iounmap() because other devices could trigger our
shared interrupt handler.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver gets Oops with ATI HDMI devices due to the wrong calculation
of index for playback streams. This patch fixes it. Reference:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3746
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pin widgets have always one amp-input value regardless of number of
connections. The proc file showed values wrongly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The capture source selection for ADC list with two elements is buggy
becaues of a wrong capture mux list. This patch fixes the starting
index based on spec->num_adc_nids.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The widget list of capture source selection for ALC883 contains the
wrong NIDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't create vmaster controls if no slaves are found in the given list.
This prevents the error due to an empty vmaster control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The GPIO pin 0 of the CM9780 must be set when muting the line input even
on non-Xonar cards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed the SPDIF output on Conexant Cx5045 codec. Added the missing
pin output setting and fixed the wrong NID for digital audio-out widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed invalid __devinit and __devexit that are remaining after
split to a helper module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some laptop has an internal analog microphone that is 'fixed'.
This patch prevents creating a 'Mic In as Output' switch for
ports that can't be outputs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This is based on pseudo-random playing around with the capabilities.
With ca0102 this card gives no output atall, ca0108 appears to work
fine, so it rather looks similar to the EMU1010b/EMU1010 changes.
Some other people seem to have succeeded in using this aswell:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3496
From: Veli-Matti Valtonen <maligor@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't create emu1010 kthread again at resume if it's already created.
Also make the thread function static.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The last change for emu1616 introduced a bug that the driver creates
emu1010-related controls even on non-emu boards. Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch improves E-Mu 1616(M) cardbus support. It adds definitions of the
new Microdock and 1010 cardbus registers (thanks again for descriptions
James) and improves mixer for this card. Now you can use S/PDIF and ADAT on
Mirodock and also use headpohone output on host cardbus card as another
independent output.
Signed-off-by: Ctirad Fertr <c.fertr@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
While the AK4396 and WM8785 datasheets say that the SPI clock cycle
length must be at least 200 ns, 320 ns seems not to work reliably with
the controller, so we better use 160 ns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
With the Solo1 (es1938) I got a lot of xrun's during capture on my machine.
Tracing that down it seems to be comming from reading ocassionaly bad hw
pointers from the chip. This patch uses more checking to avoid that false
pointer reads.
Failed reads are giving back the last good value read instead of spinning in
a tight loop, which seems more appropriate to me in an interrupt. I think I
saw this trick used in another driver
Signed-off-by: Hermann Lauer <Hermann.Lauer@iwr.uni-heidelberg.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for Intel's SCH mobile chipset.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Support added for detecting HP jack presence via GPIO on several laptop docks.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Dell T3400 with AD1984 codec chip.
ALSA bug#3699:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3699
Signed-off-by: Douglas Kosovic <douglask@itee.uq.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add SPDIF playback switch to the slave element list so that it
can be toggled via the master control as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds the Intel ICH10 HD Audio Controller DeviceID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the speaker-automute function to ALC262 HP models.
Also, 'Mono' mixer elements are renamed as more intuitive 'Speaker'.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Removed the PCM mixer elements conflicting with others.
Also renamed Master control to Headphone, which isn't a real master.
(The Master control is still created as a virtual master even after
this rename.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The PCM mixer elements in HP T5735 model of ALC262 codec conflict
with Speaker and Headphone volumes. They should be removed.
Ditto for LineOut that is identical with Speaker.
Also, fixed/cleaned up the auto-mute callback to use the amp cache
correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Renamed the non-standard mixer elements 'iSpeaker' to 'Speaker'
in Realtek codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The SPDIF output on AD1986A laptop-eapd model is disabled although
some Samsung laptops have SPDIF output. Enable it after checking the
pin default config.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
On the Xonar D2X, monitor the GPIO pin that indicates whether external
power is present.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When a second AC97 codec is present, add a PCM device for capturing from
the front panel.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
After an AC97 register read or write, use the AC97 interrupt instead of
polling to wait for the access to be completed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Move the line input switching code to the Virtuoso driver because only
the Xonar cards bypass the analog mixer for line input.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix the upper sample rate limit for the double rate mode of the AK4396
to the value from the datasheet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The AD codecs have hardware SPDIF volume/switch controls but they
are not assigned to the slave list for virtual master controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch checks to see the Line In/Mic port have the ability
to do output before creating the the control switches.
The 92hd71bxx series of codecs has this issue with the port 0xe,
which only allows input.
Signed-off-by: Matthew Ranostay <mranostay@embededalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simplify usage of the Acer Aspire 5310 laptop with the ALC268 based codec
sound card via add correct PCI SSID.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Conexant 5051 audio codec.
Right now there are two preset models, laptop and hp.
The whole patch is based on the information from the base patch by
Linuxant.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a driver for the MediaTek/TempoTec HiFier Fantasia sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Initialize more registers of the controller and the second AC97 codec.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a field to struct oxygen_model to allow model drivers for cards with
less than eight output channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This is improvement of the early support of the FM-only cards where the
fm801 chip represents the PCI to tuner bridge.
The tuner initialization isn't included the mute on as well as mute support
via V4L request. Proposed patch should fix this at least for 64-PCR model.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simplify usage of the Acer Aspire 5315 laptop with the ALC268 based codec
sound card via add correct PCI SSID.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed issue that the incorrect GPIO line was being pulled high
for some STAC9205 based laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the bug that multiple capture streams conflict on Realtek codec
routines.
Also, this adds a framework to enable the alternative playback stream,
e.g. for VoIP. It's not fully implemented yet, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allows for dynamically creating mono out mixer controls and well
as mono mux controls.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a mono_out_pin field to autocfg struct, and code to parse
for the mono_out_line.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
None of the reference design models have MIDI, only the X-Meridian
allows to connect a MIDI adapter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix up SPDIF input sample rates again: 32 kHz and 64 kHz are not
supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
snd_cs5535audio_mixer() is only called by __devinit snd_cs5535audio_probe(),
so the mixer function can also be __devinit.
WARNING: vmlinux.o(.text+0xfdbba0): Section mismatch: reference to .init.data:ac97_quirks (between 'snd_cs5535audio_mixer' and 'process_bm0_irq')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't query a widget parameter for an invalid NID in get_wcaps() but
rather returns zero (i.e. no attribute).
The read to an non-existing widget may result in a fatal codec
communication error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't read the widget list again as we already have it at the beginning.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added afg and mfg preset masks for more finer codec-preset selection.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a delay after the power state change as a partial workaround
for 'hda_intel: azx_get_response timeout' problem on Cxt codecs.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The input volume/switch elements are missing in Cxt5047 test model.
Also the patch includes some code clean ups.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Change laptop models to three different models, laptop-hpsense,
laptop-micsense and laptop-hpmicsense. The first two correspond to
the old 'laptop' and 'fujitsu' models.
Reassigned the quirk table for the new models.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add support for the mono mux on several 92HD7xxx codecs.
Creates a dynamic mixer for the mux selection.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a mixer control for the SPDIF loopback function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The TempoTec HiFier has a somwhat different architecture; remove it from
the list of cards that are known to be supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The available sample rates on CS5535 depend on AC97 codec chip.
Set the additional hw params limit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add one more indirection to the lookup of the snd_pcm_hardware
structures so that we can save the space of the duplicate ones.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Change the oxygen_spdif_input_bits_changed() function so that clock
changes on the SPDIF input are correctly detected. This means that
sample rates greater than 96 kHz are now supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix some wrong values for the definitions of the source masks for DACS 1
and 3.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Actually use the template that was maybe changed by the control filter
instead of the original one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Instead of having model-specific fields in the common struct oxygen, put
them into a private structure that is allocated together with the card
structure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
According to the datasheets, the SPI clock cycle must be at least 200 ns
for the AK4396 and the WM8785, so we cannot use the default 160 ns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow to record with 32 kHz, 64 kHz, 88.2 kHz and 176.4 kHz with cards
that have a WM8785 ADC.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add symbol definitions for the various codecs and GPIO pins.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The MIDI bit in the MISC register is set by default and cannot be used
to detect the presence of a MIDI port. Instead, add a parameter to the
oxygen_pci_probe() function so that model drivers can specify this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the DMA_PAUSE register for pausing instead of stopping DMA.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reported by Al Viro:
In copy_tlv(), the size of kmalloc is wrongly calculated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In azx_[rirb_]get_response(), the timeout is checked at the end of the loop.
It's better to be checked just after the check of the RIRB index to avoid
a bogus error with a too long msleep().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clean up ice1712/ice1724 codes. The board-specific data is allocated
locally in each code instead of having an ungly union in struct ice1712.
Also, fix coding issues in prodigy_hifi.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds additional output to the /proc codec#X info.
The following pieces of information are added to the output:
- Balanced, L/R swap, trigger, impedance sense pin capabilities
- Vref pin capabilities
- Current Vref pin widget control setting
- Default configuration association, sequence, and misc bit test
- EAPD/BTL bits conveying balanced mode, EAPD, and L/R swap
- Power state modified to show state name as well as setting vs actual value
- GPIO parameter output on Audio Function Group, including enumeration of IO
pins which are indicated present (Any I and O pins are not output at this
time)
- Stripe and L/R swap widget capabilities
- All digital converter bits: enable, validity, validity config, preemphasis,
copyright, non-audio, professional, generation level, and content category
- Converter stream and channel values for in/out widgets
- SDI select value for in widgets
- Unsolicited response widget capability tag and enabled bit
- Delay widget capability value
- Processing widget capability benign bit and number of coefficients
- Realtek Define Registers: processing coefficient, coefficient index
[Also, fixed space/tab issues and make codes a bit more readable
-- Takashi]
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The default playback routing must be 0xe4, not 0xe1; the front and
surround DACs were exchanged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add more symbols for registers and register fields.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
For codec conexant 5045, I found that the name of 'Capture Source Items'
is different from the name of mixer.
The mixer is:
HDA_CODEC_VOLUME('Ext Mic Playback Volume', 0x17, 0x2, HDA_INPUT),
HDA_CODEC_MUTE('Ext Mic Playback Switch', 0x17, 0x2, HDA_INPUT),
But the capture source item is :
static struct hda_input_mux cxt5045_capture_source = {
.num_items = 2,
.items = {
{ 'IntMic', 0x1 },
{ 'LineIn', 0x2 },
}
};
I think that it's better to change the name of capture_source to avoid
misunderstanding.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The benq r55e laptop have 3 jacks on the front panel.
One for HP, one for Line In and one for Mic In.
This patch implemented a new model to support it.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add proper register bit symbols for the I2S format field, and allow card
models to configure the I2S format to be used for the DACs and ADCs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
See ALSA bug#2384 for more details.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Konstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Codec with id 11c1:1040 sitting on hda bus isn't si3054-compatible.
It should be removed from patch_si3054.c id list.
The detailed information
http://archives.linmodems.org/26457
From: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some machines with STAC codecs seem to have problems (e.g. no audible
playback) when the delay in codec-read routine is too short.
I still don't figure out which command sequence causes this problem
(due to lack of test hardware), but it's known that increasing the
delay fixes. So, added a stupid workaround here temporarily...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This device has io_type == 1 (Multiface) and firmware_rev > 0xa
(fixes regression from changeset 5326)
Signed-off-by: Andreas Degert <ad@papyrus-gmbh.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in hdsp: snd_hdsp_proc_init() can be called from
an ioctl at any time.
WARNING: vmlinux.o(.text+0x1089bc2): Section mismatch: reference to .init.text: (between 'snd_hdsp_create_alsa_devices' and 'snd_hdsp_free')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in atiixp by making some functions __devinit.
WARNING: vmlinux.o(.text+0xfd9304): Section mismatch: reference to .init.data:atiixp_quirks (between 'ac97_probing_bugs' and 'snd_atiixp_codec_detect')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in ad1889 by renaming the pci_driver variable to a
whitelisted variable name.
WARNING: vmlinux.o(.data+0x2e5ff0): Section mismatch: reference to .init.text:snd_ad1889_probe (between 'ad1889_pci' and 'index')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a callback to the model structure to allow modification of the
hardware PCM limits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow the models to modify mixer controls before they are added to the
card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow the card models to specify whether each of the hardware DMA
channels is used.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a field to the model structure so that it is possible to have a card
where the SPI outputs 4 and 5 are used for an EEPROM.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Only initialize and create mixer controls for the first AC97 codec when
one has actually been detected.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Enable the SPDIF input-pin on VIA codecs when SPDIF-input is enabled
by BIOS. Also, including a bit code clean up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support of Dell OEM laptops (Vostro 1200) with ALC268 codec.
The new model=dell is provided.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It turned out that the PCBEEP element (0x1d) is disabled on some hardwares
although it's defined in the datasheet. Because of the error at info of
this element, the mixer gets totally unusable.
Since the PCBEEP isn't that important feature, it's safer to disable this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
There are two similar GPIO-enablement codes in patch_sigmatel.c.
Let's clean up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch removes hardcoded values for the number of streams supported
by the southbridge in most chipsets, and reads these values from the
chipset directly. Most systems are hardwired for 4 streams in each
direction, but newer chipsets change that capability.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Rename the 'PCM Playback Volume'/'Switch' mixer controls to 'Master'.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The line input cannot be mixed with the other inputs, so we have to mute
the other input switches when it is selected.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use an array for the pointers to known controls so that it is easier to
add more.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Do not exchange the surround and back jacks except when in 7.1 mode
where the surround jack is not rear but side.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch fixes 5.1 surround output and headphone detection in the
Dell Inspiron 530 and possibly other Dell systems using the ALC888
codec (mode 6stack-dell).
Signed-off-by: Claudio Matsuoka <cmatsuoka@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixes multiple device support by incrementing the static device counter
at the end of the azx_probe() call. Without this, subsequent probes would
always use the index specified for the first card.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The ALC auto-probe creates mic boost controls automatically for the
probed pins, but it assumes that they are analog mics. The digital
mics have no boost controls and must be skipped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Print the name of the defect controls in error messages in amp info
callback. This will make debugging easier.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a new STAC 9205 quirk for Vostro 1500.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for advanced power management support for output ports on
92HD7xxx family of codecs. Inactive output ports are powered down when
the pin sense doesn't detect a connection, and powered back up when a
connection is sensed.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add master controls using vmaster to codecs that have no real hardware
master volume registers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added helper functions to implement virtual master volume controls.
The virtual master control is a control element that has multiple
slave controls. The value of master element is equally added to
slave elements.
The functions are written for general purpose, but it's put in the
HD-audio directory as now, since HD-audio driver is the only user.
It should be moved to the common place once after other drivers use
vmaster.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Moved 2 systems PCI_QUIRK values to STAC_DELL_BIOS. Also the second
front HP jack is incorrect defined in the BIOS VT's for some laptops,
this patch corrects this.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Please refer to the [0003680] on ALSA bugtracking system.
The user found that 'model=mbp3' works and provided the ID.
From: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
1. Support HP rp5700
2. Fixed alc_subsystem_id function (Bug fixed and support Desktop)
3. Support ASUS EP20
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a mono output mute mixer for the 92hd71bxx family of codecs, this
also removes the need for the mono out node to explicitly unmuted in the
core init.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the proper model=laptop for HP 350 laptop with Cxt5045 codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This implements a test model for the ALC268. It depends on the feature
added by alc260-test-eapd-0.2.diff. This patch also adds a mention of
the ALC260 test model to ALSA-Configuration.txt since this seems to have
been missed.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This implements a switch control for the EAPD signal output by the ALC26x
chips. Since some laptops may utilise this to activate useful things it
is handy to have a control for this in the ALC26x test models. The patch
includes the control in the ALC260 test model.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Dynamically create digital gain mixers for dmics that have out-amp
support. Also some 92HD73xx's codecs don't have DMIC gains, so this also
prevents creating dead mixers.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It turned out that there can be multiple HD-audio devices on a single
machine (e.g. on-board audio and HDMI on graphic cards), so we need to
support multiple devices with snd-hda-intel driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds IEC958 digital out support for the AD1984 sound card.
This card can be found in Lenovo Thinkapds T61/X61. The digital out is
not located on the Thinkpad, but optional docking station (it's coxial
digital out). I've add this support as it is done the exact same way
for the AD1983 & AD1884.
I have tested this patch with my Lenovo Thinkpad T61 hooked up to a
docking station (that has the digital coxial) and then run to my home
theater reciever. Works like a charm :-)
Signed-off-by: Jerone Young <jerone@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some laptops incorrectly assume the front input jack as a line in
instead of a microphone in. Which in turn disables the voltage
reference, in which non-amplified input is not possible. This patch
enables VREF80 for the input jack.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When we store the DMA channel number in the substream's private_data
pointer, use uintptr_t as an intermediate step when casting from/to
unsigned int to prevent the compiler from whining when the pointer size
is different.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Sort the ad1986a config table by PCI SSID (the last toshiba entry was
added wrongly).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add the snd-virtuoso driver for the Asus Virtuoso 200 chip used on the
PCI and PCI-E models of the Xonar sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add the snd-oxygen driver for the C-Media CMI8788 (Oxygen) chip, used on
the Asound A-8788, AuzenTech X-Meridian, Bgears b-Enspirer,
Club3D Theatron DTS, HT-Omega Claro, Razer Barracuda AC-1,
Sondigo Inferno, and TempoTec HIFIER sound cards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
