As tunnel devices are going to be lockless, we need to make sure a
misconfigured machine wont enter an infinite loop.
Add a percpu variable, and limit to three the number of stacked xmits.
Reported-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AnyIP is the capability to receive packets and establish incoming
connections on IPs we have not explicitly configured on the machine.
An example use case is to configure a machine to accept all incoming
traffic on eth0, and leave the policy of whether traffic for a given IP
should be delivered to the machine up to the load balancer.
Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a host to be configured to respond to any address in
a specified range as if it were local, without actually needing to
configure the address on an interface. This is done through routing
table configuration. For instance, to configure a host to respond
to any address in 10.1/16 received on eth0 as a local address we can do:
ip rule add from all iif eth0 lookup 200
ip route add local 10.1/16 dev lo proto kernel scope host src 127.0.0.1 table 200
This host is now reachable by any 10.1/16 address (route lookup on
input for packets received on eth0 can find the route). On output, the
rule will not be matched so that this host can still send packets to
10.1/16 (not sent on loopback). Presumably, external routing can be
configured to make sense out of this.
To make this work, we needed to modify the logic in finding the
interface which is assigned a given source address for output
(dev_ip_find). We perform a normal fib_lookup instead of just a
lookup on the local table, and in the lookup we ignore the input
interface for matching.
This patch is useful to implement IP-anycast for subnets of virtual
addresses.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRE tunnel driver needs to invoke icmpv6 helpers in the
ipv6 stack when ipv6 support is enabled.
Therefore if IPV6 is enabled, we have to enforce that GRE's
enabling (modular or static) matches that of ipv6.
Reported-by: Patrick McHardy <kaber@trash.net>
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes kernel Bugzilla Bug 18952
This patch adds a syn_set parameter to the retransmits_timed_out()
routine and updates its callers. If not set, TCP_RTO_MIN is taken
as the calculation basis as before. If set, TCP_TIMEOUT_INIT is
used instead, so that sysctl_syn_retries represents the actual
amount of SYN retransmissions in case no SYNACKs are received when
establishing a new connection.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WMM parameter configuration function (ieee80211_sta_wmm_params) only
configures the WMM parameters to the driver is the wmm_last_param_set
counter value is changed by the AP.
The wmm_last_param_set is initialized to -1 on association in order to ensure
the configuration is made to the driver at least once on association, but
currently this initialization is done *after* the WMM parameter configuration
function was called.
This leads to unreliability in the driver getting properly configured on first
association (depending on what counter value the AP happens to use.) When
disassociating (the wmm default parameters are configured to the driver) and
then reassociating, due to the above the WMM configuration is not set to the
driver at all.
On drivers without beacon filtering the problem is corrected by later beacons,
but on drivers with beacon filtering the WMM will remain permanently incorrectly
configured.
Fix this by moving the initialization of wmm_last_param_set to -1 before
ieee80211_sta_wmm_params is called on association.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS started from wireless extensions is currently
missing basic rate configuration, fix this by moving
the code to generate the default to the common code
that gets invoked for both nl80211 and wext.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in the driver which was
exposed by CONFIG_USB_DEBUG:
"usb 1-1.6.3: BOGUS urb flags, 40 --> 0"
The transfer flag "URB_ZERO_PACKET" is only valid
for bulk urbs.
Reported-by: André Erdmann
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Ryan Niemi, some bitmasks in the register definition for the PCU
Diagnostic register (DIAG_SW) were missing a zero at the end. While at it fix
some typos and add more comments.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in ath5k_hw_get_tsf64() is time critical and will return wrong results
if we get interrupted, so disable local interrupts.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use FUDGE to make sure the next TBTT is ahead of the current TU.
Since we later substract AR5K_TUNE_SW_BEACON_RESP (10) in the timer
configuration we need to make sure it is bigger than that.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not used and it's unlikely we will ever implement ATIM.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Miller complained about the driver's excessive use
of variables in __packed structs. While I did not fully
agree with his sole "performance" argument on all accounts.
I do see some room for improvement in hot-paths on
architectures without an efficient access to unaligned
elements.
This first patch (dare I say?) optimizes an important tx
hot-path in the driver: carl9170_tx_prepare.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Broadcom's Windows driver for the 4313 advertises
an ampdu density of 7 => 16 us. The AR9170 MAC on
the other hand only supports densities up to 8 us.
This patch removes the noisy WARN_ON, because
there is nothing we can do about it.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx_ampdu_upload was not decreased when an a-MPDU
frame had to be kicked out from the tx_pending
queues.
This broke ampdu aggregation, because the scheduler
waits until tx_ampdu_upload drops to zero, before
making the next aggregate.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes some cruft, which survived
the RFC review phase.
Originally, carl9170_tx_ampdu_queue erroneously
dropped a lot of frames. As a result the ampdu
scheduler bogged down quite frequently and the
affected BA session timed out.
However this bug has been fixed and the WA and
its debugfs counter is no longer useful.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"The convention seems to be angle brackets around
URLS in Kconfig."
-- Finn Thain (to update web addresses in the kernel)
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
802.11n-2009 demands in 11.2.1: "
When a STA enters normal (non-APSD) PS mode, any downlink
Block ACK agreement without an associated schedule is
suspended for the duration of this PS mode."
The operative word is "suspended" and not terminated.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Association is dealt with as an atomic offchannel operation,
we do this because we don't know we are associated until we
get the associatin response from the AP. When we do get the
associatin response though we were never clearing the offchannel
state. This has a few implications, we told drivers we were
still offchannel, and the first configured TX power for the
channel does not take into account any power constraints.
For ath9k this meant ANI calibration would not start upon
association, and we'd have to wait until the first bgscan
to be triggered. There may be other issues this resolves
but I'm too lazy to comb the code to check.
Cc: stable@kernel.org
Cc: Amod Bodas <amod.bodas@atheros.com>
Cc: Vasanth Thiagarajan <vasanth.thiagarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945's scan_completed calls into the mac80211 stack which triggers a
warn on if there is no scan outstanding.
This can be avoided by not calling scan_completed but abort_scan in
iwl3945_request_scan in the done: branch of the function which is used
as an error out.
The done: branch seems to be an error-out branch, as, for example, if
iwl_is_ready(priv) returns false the done: branch is executed.
NOTE:
I'm not familiar with the driver at all.
I just quickly scanned as a reaction to
https://bugzilla.kernel.org/show_bug.cgi?id=17722
the users of scan_completed in the iwl3945 driver and noted the odd
discrepancy between the comment above this instance and the comment in
mac80211 scan_completed function.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix build errors, more header files needed.
drivers/net/pch_gbe/pch_gbe_main.c:965: error: implicit declaration of function 'tcp_hdr'
drivers/net/pch_gbe/pch_gbe_main.c:965: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:968: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:976: error: implicit declaration of function 'udp_hdr'
drivers/net/pch_gbe/pch_gbe_main.c:976: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:980: error: invalid type argument of '->' (have 'int')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this go away (happens when building with a separate object
directory):
Assembler messages:
Fatal error: can't create drivers/net/wireless/wl12xx/.tmp_wl12xx_platform_data.o: No such file or directory
drivers/net/wireless/wl12xx/wl12xx_platform_data.c: In function 'wl12xx_get_platform_data':
drivers/net/wireless/wl12xx/wl12xx_platform_data.c:28: error: cannot open drivers/net/wireless/wl12xx/.tmp_wl12xx_platform_data.gcno
drivers/net/wireless/wl12xx/wl12xx_platform_data.c:28: confused by earlier errors, bailing out
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Updates the Phonet document with description related to Pipe controller
implementation
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This covers RX if necessary, as well as TX.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set num_tx_queues or real_num_tx_queues, since
alloc_etherdev_mq() does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sets the active numbers of queues on a net device to match another.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RPS, we create a kobject for each RX queue based on the number of
queues passed to alloc_netdev_mq(). However, drivers generally do not
determine the numbers of hardware queues to use until much later, so
this usually represents the maximum number the driver may use and not
the actual number in use.
For TX queues, drivers can update the actual number using
netif_set_real_num_tx_queues(). Add a corresponding function for RX
queues, netif_set_real_num_rx_queues().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_attach_filter() and sk_detach_filter() are run with socket locked.
Use the appropriate rcu_dereference_protected() instead of blocking BH,
and rcu_dereference_bh().
There is no point adding BH prevention and memory barrier.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems we dont use appropriate refcount increment in an
rcu_read_lock() protected section.
fib_rule_get() might increment a null refcount and bad things could
happen.
While fib_nl_delrule() respects an rcu grace period before calling
fib_rule_put(), fib_rules_cleanup_ops() calls fib_rule_put() without a
grace period.
Note : after this patch, we might avoid the synchronize_rcu() call done
in fib_nl_delrule()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.
Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.
This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.
Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.
This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le lundi 27 septembre 2010 à 14:29 +0100, Ben Hutchings a écrit :
> > diff --git a/net/ipv4/ip_gre.c b/net/ipv4/ip_gre.c
> > index 5d6ddcb..de39b22 100644
> > --- a/net/ipv4/ip_gre.c
> > +++ b/net/ipv4/ip_gre.c
> [...]
> > @@ -377,7 +405,7 @@ static struct ip_tunnel *ipgre_tunnel_locate(struct net *net,
> > if (parms->name[0])
> > strlcpy(name, parms->name, IFNAMSIZ);
> > else
> > - sprintf(name, "gre%%d");
> > + strcpy(name, "gre%d");
> >
> > dev = alloc_netdev(sizeof(*t), name, ipgre_tunnel_setup);
> > if (!dev)
> [...]
>
> This is a valid fix, but doesn't belong in this patch!
>
Sorry ? It was not a fix, but at most a cleanup ;)
Anyway I forgot the gretap case...
[PATCH 2/4 v2] ip_gre: percpu stats accounting
Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.
Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.
This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnels are going to use percpu for their accounting.
They are going to use a new tstats field in net_device.
skb_tunnel_rx() is changed to be a wrapper around __skb_tunnel_rx()
IPTUNNEL_XMIT() is changed to be a wrapper around __IPTUNNEL_XMIT()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
