Commit Graph

146 Commits

Author SHA1 Message Date
Tejun Heo
19b723218b libata: fix last_reset timestamp handling
ehc->last_reset is used to ensure that resets are not issued too
close to each other.  It's initialized to jiffies minus one minute
on EH entry.  However, when new links are initialized after PMP is
probed, new links have zero for this timestamp resulting in long wait
depending on the current jiffies.

This patch makes last_set considered iff ATA_EHI_DID_RESET is set, in
which case last_reset is always initialized.  As an added precaution,
WARN_ON() is added so that warning is printed if last_reset is
in future.

This problem is spotted and debugged by Shane Huang.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 03:01:21 -05:00
Tejun Heo
90484ebfc9 libata: clear saved xfer_mode and ncq_enabled on device detach
libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed.  These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:40 -04:00
Tejun Heo
4a9c7b3359 libata: fix device iteration bugs
There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.

* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()

While at it, reformat comments in cable_is_40wire().

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:12 -04:00
Tejun Heo
816ab89782 libata: set device class to NONE if phys_offline
Reset methods don't have access to phys link status for slave links
and may incorrectly indicate device presence causing unnecessary probe
failures for unoccupied links.  This patch clears device class to NONE
during post-reset processing if phys link is offline.

As on/offlineness semantics is strictly defined and used in multiple
places by the core layer, this won't change behavior for drivers which
don't use slave links.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:42:43 -04:00
Tejun Heo
a568d1d2e2 libata-eh: fix slave link EH action mask handling
Slave link action mask is transferred to master link and all the EH
actions are taken by the master link.  ata_eh_about_to_do() and
ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave
link actions during transfer.  This always sets ATA_PFLAG_RECOVERED
flag causing spurious "EH complete" messages.

Don't set ATA_PFLAG_RECOVERED for slave link actions.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:21 -04:00
Tejun Heo
848e4c68c4 libata: transfer EHI control flags to slave ehc.i
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH.  As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.

This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:19 -04:00
Linus Torvalds
e26feff647 Merge branch 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
  doc/cdrom: Trvial documentation error, file not present
  block_dev: fix kernel-doc in new functions
  block: add some comments around the bio read-write flags
  block: mark bio_split_pool static
  block: Find bio sector offset given idx and offset
  block: gendisk integrity wrapper
  block: Switch blk_integrity_compare from bdev to gendisk
  block: Fix double put in blk_integrity_unregister
  block: Introduce integrity data ownership flag
  block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
  bio.h: Remove unused conditional code
  block: remove end_{queued|dequeued}_request()
  block: change elevator to use __blk_end_request()
  gdrom: change to use __blk_end_request()
  memstick: change to use __blk_end_request()
  virtio_blk: change to use __blk_end_request()
  blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
  block: add lld busy state exporting interface
  block: Fix blk_start_queueing() to not kick a stopped queue
  include blktrace_api.h in headers_install
  ...
2008-10-10 10:52:45 -07:00
Jens Axboe
242f9dcb8b block: unify request timeout handling
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.

Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:13 +02:00
Tejun Heo
11fc33da8d libata-eh: clear UNIT ATTENTION after reset
Resets make ATAPI devices raise UNIT ATTENTION which fails the next
command.  As resets can happen asynchronously for unrelated reasons,
this sometimes disrupts innocent users.  For example, reading DVD
fails after the system wakes up from suspend or the other device
sharing the channel went through bus error.

Clearing UA has some problems as it might clear UA which the userland
needs to know about.  However, UA after resets can only be about the
reset itself and benefits of clearing it overweights cons.  Missing UA
can only delay failure to one of the following commands anyway.  For
example, timeout while burning is in progress will trigger reset and
reset the device state and probably corrupt the burning run.  Although
the userland application won't get the UA, its pending writes will
fail.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:29:06 -04:00
Elias Oltmanns
45fabbb77b libata: Implement disk shock protection support
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:27:54 -04:00
Tejun Heo
b1c72916ab libata: implement slave_link
Explanation taken from the comment of ata_slave_link_init().

 In libata, a port contains links and a link contains devices.  There
 is single host link but if a PMP is attached to it, there can be
 multiple fan-out links.  On SATA, there's usually a single device
 connected to a link but PATA and SATA controllers emulating TF based
 interface can have two - master and slave.

 However, there are a few controllers which don't fit into this
 abstraction too well - SATA controllers which emulate TF interface
 with both master and slave devices but also have separate SCR
 register sets for each device.  These controllers need separate links
 for physical link handling (e.g. onlineness, link speed) but should
 be treated like a traditional M/S controller for everything else
 (e.g. command issue, softreset).

 slave_link is libata's way of handling this class of controllers
 without impacting core layer too much.  For anything other than
 physical link handling, the default host link is used for both master
 and slave.  For physical link handling, separate @ap->slave_link is
 used.  All dirty details are implemented inside libata core layer.
 From LLD's POV, the only difference is that prereset, hardreset and
 postreset are called once more for the slave link, so the reset
 sequence looks like the following.

 prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
 softreset(M) -> postreset(M) -> postreset(S)

 Note that softreset is called only for the master.  Softreset resets
 both M/S by definition, so SRST on master should handle both (the
 standard method will work just fine).

As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.

 * ata_is_host_link() updated so that slave_link is considered as host
   link too.

 * iterator extended to iterate over the slave_link when using the
   underbarred version.

 * force param handling updated such that devno 16 is mapped to the
   slave link/device.

 * ata_link_on/offline() updated to return the combined result from
   master and slave link.  ata_phys_link_on/offline() are the direct
   versions.

 * EH autopsy and report are performed separately for master slave
   links.  Reset is udpated to implement the above described reset
   sequence.

Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.

After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:25:28 -04:00
Tejun Heo
da0e21d3fa libata: use ata_link_printk() when printing SError
SError belongs to link not port.  Use ata_link_printk() to print it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:44 -04:00
Tejun Heo
5dbfc9cb59 libata: always do follow-up SRST if hardreset returned -EAGAIN
As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN.  However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN.  This
makes reset paths more predictable and thus less error-prone.

While at it, move hardreset error checking such that it's done right
after hardreset is finished.  This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:41 -04:00
Tejun Heo
a674050e06 libata: fix EH action overwriting in ata_eh_reset()
ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset().  The original intention was to clear reset action
which wasn't selected.  This can cause unexpected behavior when other
EH actions are scheduled together with reset.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:39 -04:00
Tejun Heo
05944bdf6f libata: implement no[hs]rst force params
Implement force params nohrst, nosrst and norst.  This is to work
around reset related problems and ease debugging.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:07:43 -04:00
Tejun Heo
3eabddb8ed libata-eh: update atapi_eh_request_sense() to take @dev instead of @qc
Update atapi_eh_request_sense() to take @dev, @sense_buf and
@dfl_sense_key instead of taking @qc and extracting information from
it.  This change is to make the function more generic and allow it to
be called from other places.

While at it, make cdb initialization use initializer.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Tejun Heo
87fbc5a060 libata: improve EH internal command timeout handling
ATA_TMOUT_INTERNAL which was 30secs were used for all internal
commands which is way too long when something goes wrong.  This patch
implements command type based stepped timeouts.  Different command
types can use different timeouts and each command type can use
different timeout values after timeouts.

ie. the initial timeout is set to a value which should cover most of
the cases but not too long so that run away cases don't delay things
too much.  After the first try times out, the second try can use
longer timeout and if that one times out too, it can go for full 30sec
timeout.

IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s -
10s timeouts.

This patch significantly cuts down the needed time to handle failure
cases while still allowing libata to work with nut job devices through
retries.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo
d8af0eb604 libata: use ULONG_MAX to terminate reset timeout table
This doesn't introduce any functional changes.  This is to make reset
timeout table consistent with to-be-added command timeout tables.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo
0a2c0f5615 libata: improve EH retry delay handling
EH retries were delayed by 5 seconds to ensure that resets don't occur
back-to-back.  However, this 5 second delay is superflous or excessive
in many cases.  For example, after IDENTIFY times out, there's no
reason to wait five more seconds before retrying.

This patch adds ehc->last_reset timestamp and record the timestamp for
the last reset trial or success and uses it to space resets by
ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec
sleeps.

As this change makes inter-try waits often shorter and they're
redundant in nature, this patch also removes the "retrying..."
messages.

While at it, convert explicit rounding up division to DIV_ROUND_UP().

This change speeds up EH in many cases w/o sacrificing robustness.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo
341c2c958e libata: consistently use msecs for time durations
libata has been using mix of jiffies and msecs for time druations.
This is getting confusing.  As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs.  So, durations are in msecs and
deadlines are in jiffies.  ata_deadline() is added to compute deadline
from a start time and duration in msecs.

While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo
e0614db2a3 libata: ignore recovered PHY errors
No reason to get overzealous about recovered comm and data errors.
Some PHYs habitually sets them w/o no good reason and being draconian
about these soft error conditions doesn't seem to help anybody.

If need ever rises, we might need to add soft PHY error condition, say
AC_ERR_MAYBE_ATA_BUS and use it only to determine whether speed down
is necessary but I don't think that's very likely to happen.  It's far
more likely we'll get timeouts or fatal transmission errors if
recovered errors are so prominent that they hamper operation.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Tejun Heo
f046519fc8 libata: kill hotplug related race condition
Originally, whole reset processing was done while the port is frozen
and SError was cleared during @postreset().  This had two race
conditions.  1: hotplug could occur after reset but before SError is
cleared and libata won't know about it.  2: hotplug could occur after
all the reset is complete but before the port is thawed.  As all
events are cleared on thaw, the hotplug event would be lost.

Commit ac371987a8 kills the first race
by clearing SError during link resume but before link onlineness test.
However, this doesn't fix race #2 and in some cases clearing SError
after SRST is a good idea.

This patch solves this problem by cross checking link onlineness with
classification result after SError is cleared and port is thawed.
Reset is retried if link is online but all devices attached to the
link are unknown.  As all devices will be revalidated, this one-way
check is enough to ensure that all devices are detected and
revalidated reliably.

This, luckily, also fixes the cases where host controller returns
bogus status while harddrive is spinning up after hotplug making
classification run before the device sends the first FIS and thus
causes misdetection.

Low level drivers can bypass the logic by setting class explicitly to
ATA_DEV_NONE if ever necessary (currently none requires this).

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Tejun Heo
dc98c32cbe libata: move reset freeze/thaw handling into ata_eh_reset()
Previously reset freeze/thaw handling lived outside of ata_eh_reset()
mainly because the original PMP reset code needed the port frozen
while resetting all the fan-out ports, which is no longer the case.

This patch moves freeze/thaw handling into ata_eh_reset().
@prereset() and @postreset() are now called w/o freezing the port
although @prereset() an be called frozen if the port is frozen prior
to entering ata_eh_reset().

This makes code simpler and will help removing hotplug event related
races.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Tejun Heo
932648b007 libata: reorganize ata_eh_reset() no reset method path
Reorganize ata_eh_reset() such that @prereset() is called even when no
reset method is available and if block is used instead of goto to skip
actual reset.  This makes no reset case behave better (readiness wait)
and future changes easier.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Mark Lord
10acf3b0d3 libata: export ata_eh_analyze_ncq_error
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:37:58 -04:00
Mark Lord
a6116c9e60 libata-eh set tf flags in NCQ EH result_tf
Fix mis-reporting of NCQ errors by ensuring that result_tf->flags
is properly initialized in libata-eh.  This allows ata_gen_ata_sense()
to report the failed block number correctly to SCSI after a media error
during NCQ.

This patch may also be a candidate for backporting to earlier kernels.
Without this fix, SCSI will fail I/O on the entire request rather
than just the bad sector.  That can be bad for a request that was
merged from many independent read reads from different tasks.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:11:37 -04:00
Tejun Heo
4f7faa3f2b libata: make EH fail gracefully if no reset method is available
When no reset method is available, libata currently oopses.  Although
the condition can't happen unless there's a bug in a low level driver,
oopsing isn't the best way to report the error condition.  Complain,
dump stack and fail reset instead.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:26 -04:00
Tejun Heo
45db2f6c95 libata: move link onlineness check out of softreset methods
Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.

This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.

sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset.  This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
2a0c15ca39 libata: kill dead code paths in reset path
Some code paths which had been made obsolete by recent reset
simplification were still around.  Kill them.

* ata_eh_reset() checked for ATA_DEV_UNKNOWN to determine
  classification failure.  This is no longer applicable.

* ata_do_reset() should convert ATA_DEV_UNKNOWN to ATA_DEV_NONE
  regardless of reset result (e.g. -EAGAIN).

* LLDs don't need to convert ATA_DEV_UNKNOWN to ATA_DEV_NONE.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
071f44b1d2 libata: implement PMP helpers
Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link.  While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.

This change simplifies LLDs and helps making PMP support optional.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
305d2a1ab1 libata: unify mechanism to request follow-up SRST
Previously, there were two ways to trigger follow-up SRST from
hardreset method - returning -EAGAIN and leaving all device classes
unmodified.  Drivers never used the latter mechanism and the only use
case for the former was when hardreset couldn't classify.

Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST
if classification is required".  This change removes unnecessary
follow-up SRSTs and simplifies reset implementations.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
5958e3025f libata: move PMP SCR access failure during reset to ata_eh_reset()
If PMP fan-out reset fails and SCR isn't accessible, PMP should be
reset.  This used to be tested by sata_pmp_std_hardreset() and
communicated to EH by -ERESTART.  However, this logic is generic and
doesn't really have much to do with specific hardreset implementation.

This patch moves SCR access failure detection logic to ata_eh_reset()
where it belongs.  As this makes sata_pmp_std_hardreset() identical to
sata_std_hardreset(), the function is killed and replaced with the
standard method.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
57c9efdfb3 libata: implement and use sata_std_hardreset()
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset().  sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.

ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.

piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
9363c3825e libata: rename SFF functions
SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:21 -04:00
Tejun Heo
03faab7827 libata: implement ATA_QCFLAG_RETRY
Currently whether a command should be retried after failure is
determined inside ata_eh_finish().  Add ATA_QCFLAG_RETRY and move the
logic into ata_eh_autopsy().  This makes things clearer and helps
extending retry determination logic.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
a1efdaba2d libata: make reset related methods proper port operations
Currently reset methods are not specified directly in the
ata_port_operations table.  If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods.  It's done this way for two reasons.

First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.

Second, as ->error_handler uses those reset methods, it can get
confusing.  ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.

Now that ops table uses inheritance, the first problem doesn't exist
anymore.  The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks.  In fact, there currently is no driver which actually
modifies error handling behavior.  Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH.  I don't think making ops layering strict has
any noticeable benefit.

This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops.  Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.

* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
  aren't accessible.  sata_promise doesn't need to use separate
  error_handlers for PATA and SATA anymore.

* softreset is broken for sata_inic162x and sata_sx4.  As libata now
  always prefers hardreset, this doesn't really matter but the ops are
  forced to NULL using ATA_OP_NULL for documentation purpose.

* pata_hpt374 needs to use different prereset for the first and second
  PCI functions.  This used to be done by branching from
  hpt374_error_handler().  The proper way to do this is to use
  separate ops and port_info tables for each function.  Converted.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:18 -04:00
Tejun Heo
b558edddb1 libata: kill ata_ehi_schedule_probe()
ata_ehi_schedule_probe() was created to hide details of link-resuming
reset magic.  Now that all the softreset workarounds are gone,
scheduling probe is very simple - set probe_mask and request RESET.
Kill ata_ehi_schedule_probe() and open code it.  This also increases
consistency as ata_ehi_schedule_probe() couldn't cover individual
device probings so they were open-coded even when the helper existed.

While at it, define ATA_ALL_DEVICES as mask of all possible devices on
a link and always use it when requesting probe on link level for
simplicity and consistency.  Setting extra bits in the probe_mask
doesn't hurt anybody.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
672b2d65ba libata: kill ATA_EHI_RESUME_LINK
ATA_EHI_RESUME_LINK has two functions - promote reset to hardreset if
ATA_LFLAG_HRST_TO_RESUME is set and preventing EH from shortcutting
reset action when probing is requested.  The former is gone now and
the latter can easily be achieved by making EH to perform at least one
reset if reset is requested, which also makes more sense than
depending on RESUME_LINK flag.

As ATA_EHI_RESUME_LINK was the only EHI reset modifier, this also
kills reset modifier handling.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
cf48062658 libata: prefer hardreset
When both soft and hard resets are available, libata preferred
softreset till now.  The logic behind it was to be softer to devices;
however, this doesn't really help much.  Rationales for the change:

* BIOS may freeze lock certain things during boot and softreset can't
  unlock those.  This by itself is okay but during operation PHY event
  or other error conditions can trigger hardreset and the device may
  end up with different configuration.

  For example, after a hardreset, previously unlockable HPA can be
  unlocked resulting in different device size and thus revalidation
  failure.  Similar condition can occur during or after resume.

* Certain ATAPI devices require hardreset to recover after certain
  error conditions.  On PATA, this is done by issuing the DEVICE RESET
  command.  On SATA, COMRESET has equivalent effect.  The problem is
  that DEVICE RESET needs its own execution protocol.

  For SFF controllers with bare TF access, it can be easily
  implemented but more advanced controllers (e.g. ahci and sata_sil24)
  require specialized implementations.  Simply using hardreset solves
  the problem nicely.

* COMRESET initialization sequence is the norm in SATA land and many
  SATA devices don't work properly if only SRST is used.  For example,
  some PMPs behave this way and libata works around by always issuing
  hardreset if the host supports PMP.

  Like the above example, libata has developed a number of mechanisms
  aiming to promote softreset to hardreset if softreset is not going
  to work.  This approach is time consuming and error prone.

  Also, note that, dependingon how you read the specs, it could be
  argued that PMP fan-out ports require COMRESET to start operation.
  In fact, all the PMPs on the market except one don't work properly
  if COMRESET is not issued to fan-out ports after PMP reset.

* COMRESET is an integral part of SATA connection and any working
  device should be able to handle COMRESET properly.  After all, it's
  the way to signal hardreset during reboot.  This is the most used
  and recommended (at least by the ahci spec) method of resetting
  devices.

So, this patch makes libata prefer hardreset over softreset by making
the following changes.

* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
  ATA_EH_{SOFT|HARD}RESET used to be used.  ATA_EH_{SOFT|HARD}RESET is
  now only used to tell prereset whether soft or hard reset will be
  issued.

* Strip out now unneeded promote-to-hardreset logics from
  ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
  other places.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:15 -04:00
Tejun Heo
3ec25ebd69 libata: ATA_EHI_LPM should be ATA_EH_LPM
EH actions are ATA_EH_* not ATA_EHI_*.  Rename ATA_EHI_LPM to
ATA_EH_LPM.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-29 12:21:31 -04:00
Tejun Heo
eec59f76e9 libata: allow LLDs w/o any reset method
Some old SFF controllers don't have any way to reset the channel.
Currently, this isn't supported and libata EH causes an oops.  Allow
LLDs w/o any reset method and just assume ATA class in such cases.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:50:34 -04:00
Tejun Heo
3326732570 libata: implement libata.force module parameter
This patch implements libata.force module parameter which can
selectively override ATA port, link and device configurations
including cable type, SATA PHY SPD limit, transfer mode and NCQ.

For example, you can say "use 1.5Gbps for all fan-out ports attached
to the second port but allow 3.0Gbps for the PMP device itself, oh,
the device attached to the third fan-out port chokes on NCQ and
shouldn't go over UDMA4" by the following.

 libata.force=2:1.5g,2.15:3.0g,2.03:noncq,udma4

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-20 12:12:28 -05:00
Tejun Heo
75f9cafc2d libata: fix off-by-one in error categorization
ATA_ECAT_DUBIOUS_BASE was too high by one and thus all DUBIOUS error
categorizations were wrong.  This passed test because only ATA_BUS and
UNK_DEV were used during testing and the ones after them - ATA_BUS and
an overflowed entry - behaved similarly.

This patch fixes the problem by adding DUBIOUS_NONE category and use
it as base.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:17 -05:00
Tejun Heo
0dc36888d4 libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and
ATA_PROT_ATAPI_* are inconsistent causing confusion.  Rename them to
ATAPI_PROT_* and make them consistent with ATA counterpart.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23 05:24:14 -05:00
Andrew Morton
e6a73ab1c8 drivers/ata/libata-eh.c: fix printk warning
drivers/ata/libata-eh.c: In function `ata_port_pbar_desc':
drivers/ata/libata-eh.c:215: warning: long long unsigned int format, long unsigned int arg (arg 4)

Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:13 -05:00
Jeff Garzik
e39eec13ff [libata] Build fix WRT ata_is_xxx() new API introduction
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23 05:24:11 -05:00
Tejun Heo
76326ac1ac libata: implement fast speed down for unverified data transfer mode
It's very likely that the configured data transfer mode is the wrong
one if device fails data transfers right after initial data transfer
mode configuration (including NCQ on/off and xfermode).  libata EH
needs to speed down fast before upper layers give up on probing.

This patch implement fast speed down rules to handle such cases
better.  Error occured while data transfer hasn't been verified
trigger fast back-to-back speed down actions until data transfer
works.

This change will make cable mis-detection and other initial
configuration problems corrected before partition scanning code gives
up.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:11 -05:00
Tejun Heo
00115e0f5b libata: implement ATA_DFLAG_DUBIOUS_XFER
ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method
changes and gets cleared when data transfer command succeeds in the
newly configured transfer mode.

This will be used to improve speed down logic.

Signed-off-by: Tejun Heo <htejun@gmail.com<
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:11 -05:00
Tejun Heo
663f99b86a libata: adjust speed down rules
Speed down rules were too conservative.  Adjust them a bit.

* More than 10 timeouts can't happen in 5 minutes as command timeout
  is 30secs.  Lower the limit for rule #1 to 6.

* 10 timeouts is too high for rule #3 too.  Lower it to 6.

* SATAPI can benefit from falling back to PIO too.  Allow SATAPI
  devices to fall back to PIO.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:11 -05:00
Tejun Heo
3884f7b0a8 libata: clean up EH speed down implementation
Clean up EH speed down implementation.

* is_io boolean variable is replaced eflags.  is_io is ATA_EFLAG_IS_IO.

* Error categories now have names.

* Better comments.

* Reorder 5min and 10min rules in ata_eh_speed_down_verdict()

* Use local variable @link to cache @dev->link in ata_eh_speed_down()

These changes are to improve readability and ease further changes.
This patch doesn't introduce any behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:10 -05:00