Commit Graph

1192 Commits

Author SHA1 Message Date
Sean Hefty
24be6e81c7 IB/cm: Use spin_lock_irq() instead of spin_lock_irqsave() when possible
The ib_cm is a little over zealous about using spin_lock_irqsave,
when spin_lock_irq would do.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-10 21:47:29 -07:00
Sean Hefty
2aec5c602c IB/sa: Make sure SA queries use default P_Key
MADs sent to the SA should use the the default P_Key (0x7fff/0xffff).
There's no requirement that the default P_Key is stored at index 0 in
the local P_Key table, so add code to the sa_query module to look up
the index of the default P_Key when creating an address handle for the
SA (which is done any time the P_Key table might change), and use this
index for all SA queries.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-10 21:45:31 -07:00
Roland Dreier
1b844afe9e IPoIB: Recycle loopback skbs instead of freeing and reallocating
InfiniBand HCAs replicate multicast packets back to the QP that sent
them if that QP is attached to the destination multicast group.  This
means that IPoIB multicasts are often replicated back to the receive
queue of the interface that generated them.  To avoid confusing the
network stack, we drop these duplicates within the IPoIB driver.

However, there's no reason to free the skb that received the duplicate
and then immediately allocate a new skb to post to the receive queue.
We can be more efficient and just repost the same skb.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-10 13:43:53 -07:00
Shani Moideen
8909c571fa IB/mthca: Replace memset(<addr>, 0, PAGE_SIZE) with clear_page(<addr>)
Signed-off-by: Shani Moideen <shani.moideen@wipro.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
----
2007-07-10 12:28:05 -07:00
Roland Dreier
20089ca557 IPoIB/cm: Fix warning if IPV6 is not enabled
Fix

    drivers/infiniband/ulp/ipoib/ipoib_cm.c:1151: warning: unused variable 'dev'

by getting rid of the variable dev, which is only used if CONFIG_IPV6
is enabled, and replacing the one use of it with the value it is
assigned, namely priv->dev.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-10 11:18:34 -07:00
Dotan Barak
856c52a741 IB/core: Take sizeof the correct pointer when calling kmalloc()
When allocating out_mad in show_pma_counter(), take sizeof *out_mad
instead of sizeof *in_mad.  It is true that today the type of in_mad
and out_mad are the same, but this patch will give us a cleaner code.

Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-10 11:04:40 -07:00
Hoang-Nam Nguyen
f72d2f0814 IB/ehca: Improve latency by unlocking after triggering the hardware
Kick the hardware before unlocking the send/receive queue to overlap
processing a little more.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Joachim Fenkes
8705ce5b90 IB/ehca: Notify consumers of LID/PKEY/SM changes after nondisruptive events
When firmware reports a nondisruptive port configuration change event,
previous versions of the eHCA driver didn't forward the event to consumers
like IPoIB.  Add code that determines the type of configuration change by
comparing old and new port attributes and reports it.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Joachim Fenkes
b1cfe43d4b IB/ehca: Return QP pointer in poll_cq()
Also add two unlikely() statements.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Joachim Fenkes
26ed687fdd IB/ehca: Change idr spinlocks into rwlocks
This eliminates lock contention among IRQs as well as the need to
disable IRQs around idr_find, because there are no IRQ writers.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Joachim Fenkes
28db6beb42 IB/ehca: Refactor sync between completions and destroy_cq using atomic_t
- ehca_cq.nr_events is made an atomic_t, eliminating a lot of locking.
- The CQ is removed from the CQ idr first now to make sure no more
  completions are scheduled on that CQ. The "wait for all completions to
  end" code becomes much simpler this way.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Joachim Fenkes
9844b71baa IB/ehca: Lock renaming, static initializers
- Rename all spinlock flags to "flags", matching the vast majority of kernel
  code.
- Move hcall_lock into the only file it's used in.
- Replaced spin_lock_init() and friends with static initializers for
  global variables.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Hoang-Nam Nguyen
15f001ec47 IB/ehca: Report RDMA atomic attributes in query_qp()
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Stefan Roscher
85f003172f IB/ehca: Set SEND_GRH flag for all non-LL UD QPs on eHCA2
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Stefan Roscher
472803dab8 IB/ehca: Support UD low-latency QPs
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Joachim Fenkes
a6a12947fb IB/ehca: add Shared Receive Queue support
Support SRQs on eHCA2. Since an SRQ is a QP for eHCA2, a lot of code
(structures, create, destroy, post_recv) can be shared between QP and SRQ.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Joachim Fenkes
9a79fc0a1b IB/ehca: QP code restructuring in preparation for SRQ
- Replace init_qp_queues() by a shorter init_qp_queue(), eliminating
  duplicate code.

- hipz_h_alloc_resource_qp() doesn't need a pointer to struct ehca_qp any
  longer. All input and output data is transferred through the parms
  parameter.

- Change the interface to also support SRQ.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Joachim Fenkes
91f13aa3fc IB/ehca: HW level, HW caps and MTU autodetection
In preparation for support of new eHCA2 features, change adapter probing:
 - Hardware level is changed to encode major and minor chip version
 - Hardware capabilities are queried from the firmware
 - The maximum MTU is queried from the firmware instead of assuming a
   fixed value

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:27 -07:00
Hoang-Nam Nguyen
b8a3ba5513 IB/ehca: Change scaling_code parameter description to match default value
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Sean Hefty
f41d229865 IB/ipath: return correct PortGUID in NodeInfo
Return the PortGUID of the correct port when responding to a NodeInfo
query.  Returning the SystemImageGUID causes issues when there are
multiple HCAs in a single system.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Arthur Jones
4f5973fd3b IB/ipath: Remove bogus RD_ATOMIC checks from modify_qp
The changeset 3859e39d ("IB/ipath: Support larger IB_QP_MAX_DEST_RD_ATOMIC
and IB_QP_MAX_QP_RD_ATOMIC") added support for larger RD_ATOMIC values,
but it failed to take out the stricter checks that were before these and
hence had no effect.  This patch takes out the bogus checks....

Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Arthur Jones
3588423fba IB/ipath: Test interrupts at driver startup
All too often, interrupts do not get enabled for our card due to BIOS
misconfiguration and other issues.  This patch checks for that
condition on startup and warns the user.  This patch is based on work
(check LID availability) by Robert Walsh.

Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
9ca4865566 IB/ipath: Remove support for preproduction HTX InfiniPath cards
Clean up some code by removing support for some older pre-production
HTX InfiniPath cards.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
2007-07-09 20:12:26 -07:00
Dave Olson
12f9a49e1b IB/ipath: Change version wording to be less confusing with release number
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
37a7e9b7f2 IB/ipath: Lower default number of kernel send buffers
The default calculation for the number of send buffers to allocate to
the kernel was too high for the PCIe version of the chip thus leaving
fewer than desired send buffers for user MPI applications.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Dave Olson
0f4fc5ebd9 IB/ipath: Be more cautious about coming out of freeze mode
We are more careful to be sure that we don't lose information about
changes that occurred while we were in freeze mode, when the chip will
not notify us, and try to avoid false error interrupts while doing
cleanup.  Put all of this logic in a new function ipath_clear_freeze().

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
4fc570bcbe IB/ipath: Add barrier before updating WC head in shared memory
Add a barrier to make sure the CPU doesn't reorder writes to memory,
since user programs can be polling on the head index update and the
entry should be written before that.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Jan Engelhardt
06cc85086e IB: Use menuconfig for InfiniBand menu
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.

Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
WANG Cong
6abb6ea80b RDMA/cxgb3: Check return of kmalloc() in iwch_register_device()
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
[ Also remove cast from void * return of kmalloc() as suggested by  
  Jesper Juhl <jesper.juhl@gmail.com>. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Steve Wise
ecc2f0060f RDMA/cxgb3: Don't abort after failures sending the mpa reply
This bug results in an abort request being sent down _after_ the tid
has been released.  If the tid happens to have been reused, then the
subsequent generation of the tid gets incorrectly aborted.

The thread running iwch_accecpt_cr() must not abort a connection if an
error is returned after being awakened.  If any errors did occur while
iwch_accept_cr() is blocked, then the connection has already been
aborted on the thread processing the error.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Steve Wise
96d0e4931e RDMA/cxgb3: Don't post TID_RELEASE message
The LLD does this for us in cxgb3_remove_tid().

Also fixed active open failure cases where we also shouldn't be
releasing the TID.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Steve Wise
6eda48d1e8 RDMA/cxgb3: ctrl-qp init/clear shouldn't set the gen bit
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Steve Wise
1580367e7b RDMA/cxgb3: Don't count neg_adv abort_req_rss messages as real aborts
Negative advice messages should _not_ count toward the 2 abort
requests needed to indicate an abort request.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Steve Wise
fb497d7266 RDMA/cxgb3: TERMINATE WRs can hang the tx ofld queue
Don't set the gen bits nor length bits in the terminate WR.  This is
done by the LLD driver.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Steve Wise
de3d353072 RDMA/cxgb3: Streaming -> RDMA mode transition fixes
Due to a HW issue, our current scheme to transition the connection from
streaming to rdma mode is broken on the passive side.  The firmware
and driver now support a new transition scheme for the passive side:

 - driver posts rdma_init_wr (now including the initial receive seqno)
 - driver posts last streaming message via TX_DATA message (MPA start
   response)
 - uP atomically sends the last streaming message and transitions the
   tcb to rdma mode.
 - driver waits for wr_ack indicating the last streaming message was ACKed.

NOTE: This change also bumps the required firmware version to 4.3.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Dotan Barak
149983af60 mlx4_core: Get the maximum message size from reported device capabilities
Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
John Gregor
87427da55b IB/ipath: Update copyright dates
Now that it's June, it's about time to update
the copyright notices of files that have changed.

Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Robert Walsh
991bda284d IB/ipath: Clean send flags properly on QP reset
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Robert Walsh
f2d042313e IB/ipath: ipath_poll fixups and enhancements
Fix ipath_poll and enhance it so we can poll for urgent packets or
regular packets and receive notifications of when a header queue
overflows.

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Robert Walsh
b506e1dc59 IB/ipath: Send ACK invalid where appropriate
The IB specification ch. 9.9.3 table 58 says that a QP which isn't set
up for the operation should return a NAK invalid request.

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Michael Albaugh
e8e7ad7115 IB/ipath: Add capability to modify PBC word
During compliance testing and when debugging some interconnect issues,
it is very useful to be able to send malformed packets, without having
the device signal them as malformed (drop, or terminate with EBP). The
hardware supports this, but the driver "diagnostic packet" interface
did not.

Extend capability to send specific malformed packets for testing.

Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Mark Debbage
bacf401353 IB/ipath: Make handling of one subport consistent
Previously the driver and userspace code handled the case of 1 subport
somewhat inconsistently.  The new interpretation of this situation is
that if one subport is requested, the driver turns on the subport
mechanism and arranges for the port to be "shared" by one process.  In
normal use the userspace library does not use this configuration and
instead arranges for the port not to be shared at all.  This
particular idiom can be useful for testing purposes.

Signed-off-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Mark Debbage
0df6291c8a IB/ipath: Correct checking of swminor version field when using subports
When subports are required to run a program, this patch checks that
the driver and the userspace library have compatible subport
implementations.  This is achieved through checks on the swminor
version field built into the driver and userspace library.  Bad
combinations are reported through syslog and result in an error when
opening the port.

Signed-off-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
d781b129f1 IB/ipath: Duplicate RDMA reads can cause responder to NAK inappropriately
A duplicate RDMA read request can fool the responder into NAKing a new
RDMA read request because the responder wasn't keeping track of
whether the queue of RDMA read requests had been sent at least once.
For example, requester sends 4 2K byte RDMA read requests, times out,
and resends the first, then sees the 4 responses, then sends a 5th
RDMA read or atomic operation.  The responder sees the 4 requests,
sends 4 responses, sees the resent 1st request, rewinds the queue,
then sees the 5th request but thinks the queue is full and that the
requester is invalidly sending a 5th new request.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
30d149ab58 IB/ipath: Fix possible data corruption if multiple SGEs used for receive
The code to copy data from the receive queue buffers to the IB SGEs
doesn't check the SGE length, only the memory region/page length when
copying data.  This could overwrite parts of the user's memory that
were not intended to be written.  It can only happen if multiple SGEs
are used to describe a receive buffer which almost never happens in
practice.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
db5518cd09 IB/ipath: Wait for PIO available interrupt
The send function is called when posting new send work requests.
There is no point in trying to send a packet if the QP is already
waiting for a HW send buffer so don't clear the busy bit until the
buffer available interrupt happens.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
06ee109002 IB/ipath: Fix RDMA read retry code
A RDMA read response or atomic response can ACK earlier sends and RDMA
writes.  In this case, the wrong work request pointer was being used
to store the read first response or atomic result.  Also, if a RDMA
read request is retried, the code to compute which request to resend
was incorrect.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Dave Olson
9380068fc2 IB/ipath: Use S_ABORT not cancel and abort on exit freeze mode after recovery
This centralizes the use of the abort functionality, removes the
unneeded buffer cancel (abort does the same thing), sets up to ignore
launch errors after abort, same as cancel.  We need abort on exit from
freeze mode to avoid having buffers stuck in the busy state, if a user
process happened to complete the send while we were in freeze mode
doing the recovery.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Dave Olson
561095f20e IB/ipath: Fix the mtrr_add args for chips with 2 buffer sizes
The values passed have never been right for iba 6120 chips, but just
happened to work.  We needed to select the right buffer offset in the
chip (both are in same register), and the total length was wrong also,
but was covered by the rounding up.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Joan Eslinger
f716cdfe57 IB/ipath: Change use of constants for TID type to defined values
Define pkt rcvd 'type' in a way consistent with HW spec and chips.

The hardware considers received packets of type 0 to be expected, and
type 1 to be eager. The driver was calling the ipath_f_put_tid
functions using a variable called 'type' set to 0 for eager and to 1
for expected packets.  Worse, the iba6110 and iba6120 drivers used
those values inconsistently.  This was quite confusing.  Now
everything is consistent with the hardware.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
1dd6a1be14 IB/ipath: Set M bit in BTH according to IB spec
According to chapter 17.2.8.1.1, QPs start in the migrated state and
should send packets with the M bit set in the BTH.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
6d2fad0472 IB/ipath: Fix local loopback bug when waiting for resources
This patch fixes a minor bug where the wrong QP was checked for a send
work request that should wait for an RNR timeout.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Ralph Campbell
2c9749c3b5 IB/ipath: Fix problem with next WQE after a UC completion
This patch fixes a bug introduced when moving some code around for
readability.

Setting the wqe pointer at the end of the function is a NOP since it
isn't used.  Move it back to where it is used.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Robert Walsh
fdc7215fbd IB/ipath: Fill in some missing FMR-related fields in query_device
In ipath_query_device(), some of the struct ib_device_attr fields were
not being initialized.

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Robert Walsh
e7340f0442 IB/ipath: Fix maximum MTU reporting
Although our chip supports 4K MTUs, our driver doesn't yet support
this feature, so limit the maximum MTU to 2K until we get support for
4K MTUs implemented.

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:25 -07:00
Dave Olson
380bf5d38f IB/ipath: Support the IBA6110 revision 4
Recognize IBA 6110 Revision 4: same feature set, etc. as earlier revisions.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:25 -07:00
Michael Albaugh
aecd3b5ab1 IB/ipath: Log "active" time and some errors to EEPROM
We currently track various errors, now we enhance that capability by
logging some of them to EEPROM.  We also now log a cumulative "active"
time defined by traffic though the InfiniPath HCA beyond the normal SM
traffic.

Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:25 -07:00
John Gregor
8e9ab3f1c9 IB/ipath: Remove incompletely implemented ipath_runtime flags and code
The IPATH_RUNTIME_PBC_REWRITE and the IPATH_RUNTIME_LOOSE_DMA_ALIGN
flags were not ever implemented correctly and did not turn out to be
necessary.  Remove the last vestiges of these flags but mark the spot
with a comment to remind us to not reuse these flags in the interest
of binary compatibility.  The INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR
bit was also not found to be useful, so it was dropped in the cleanup
as well.

Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:25 -07:00
Michael Albaugh
17b2eb9fe6 IB/ipath: Lock and always use shadow copies of GPIO register
The new LED blinking interface adds more contention for the
unprotected GPIO pins that were already shared, though not commonly at
the same time.  We add locks to the accesses to these pins so that
Read-Modify-Write is now safe.  Some of these locks are added at
interrupt context, so we shadow the registers which drive and inspect
these pins to avoid the mmio read/writes.  This mitigates the effects
of the locks and hastens us through the interrupt.

Add locking and always use shadows for registers controlling GPIO pins
(ExtCtrl and GPIOout). The use of shadows implies doing less I/O,
which can make I2C operation too fast on some platforms. An explicit
udelay(1) in SCL manipulation fixes that.

Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:25 -07:00
Michael Albaugh
82466f00ec IB/ipath: Support blinking LEDs with an led_override file
When we want to find an InfiniPath HCA in a rack of nodes, it is often
expeditious to blink the status LEDs via a userspace /sys file.

A write-only led_override "file" is published per device. Writes to
this file are interpreted as (string form) numbers, and the resulting
value sent to ipath_set_led_override(). The upper eight bits are
interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom
two 4-bit values are alternately (D0..3, then D4..7) used by the
board-specific LED-setting function to override the normal state.

Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:25 -07:00
Bryan O'Sullivan
a024291b36 IB/ipath: Include <linux/vmalloc.h> to fix ppc64 build
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:25 -07:00
Michael S. Tsirkin
63019d9329 IB/mlx4: Include linux/mutex.h from mlx4_ib.h
mlx4_ib.h uses struct mutex, so although <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include <linux/mutex.h> directly.

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 16:17:33 -07:00
Andrew Morton
1d3f4b905a IB: Fix ib_umem_get() when npages == 0
gcc correctly warned:

drivers/infiniband/core/umem.c: In function 'ib_umem_get':
drivers/infiniband/core/umem.c:78: warning: 'ret' may be used uninitialized in this function

Set ret to 0 in case npages == 0 and the loop isn't entered at all.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 16:17:33 -07:00
Roland Dreier
43506d954e IB: Remove garbage non-ASCII characters from comments
A few files had 0xa0 characters in comments.  Remove them so that the 
files are clean ASCII text.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 16:17:32 -07:00
Joachim Fenkes
fffba373ef IB/ehca: Refactor "maybe missed event" code
Refactor the ehca changes from commit ed23a727 ("IB: Return "maybe
missed event" hint from ib_req_notify_cq()") so the queue arithmetic
is done in slightly fewer lines.  Also, move the spinlock flags into
the block they're used in.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 16:17:32 -07:00
Hal Rosenstock
1bae4dbf95 IB/mad: Enhance SMI for switch support
Extend the SMI with switch (intermediate hop) support. Care has been
taken to ensure that the CA (and router) code paths are changed as
little as possible.

Signed-off-by: Suresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 16:17:32 -07:00
Ralph Campbell
841adfca9c IPoIB/cm: Partial error clean up unmaps wrong address
If a page can't be allocated for the frag list of a skb, the code to
unmap the partially allocated list is off by one.  For exaple, if
'frags' equals one, i == 0, and the alloc_page() fails, then the old
loop would have unmapped mapping[1] which is uninitialized.  The same
would happen if the call to ib_dma_map_page() failed.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-02 20:48:31 -07:00
Jack Morgenstein
c8681f1401 IB/mlx4: Correct max_srq_wr returned from mlx4_ib_query_device()
We need to keep a spare entry in the SRQ so that there always is a
next WQE available when posting receives (so that we can tell the
difference between a full queue and an empty queue).  So subtract 1
from the value HW gives us before reporting the limit on SRQ entries
to consumers.

Found by Mellanox QA.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-21 13:39:10 -07:00
Roland Dreier
13ef5f44c3 IPoIB/cm: Remove dead definition of struct ipoib_cm_id
It's completely unused.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-21 13:39:08 -07:00
Michael S. Tsirkin
82c3aca6ad IPoIB/cm: Fix interoperability when MTU doesn't match
IPoIB connected mode currently rejects a connection request unless the
supported MTU is >= the local netdevice MTU. This breaks
interoperability with implementations that might have tweaked
IPOIB_CM_MTU, and there's real no longer a reason to do so: this test
is just a leftover from when we did not tweak MTU per-connection.  Fix
this by making the test as permissive as possible.

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-21 13:38:08 -07:00
Michael S. Tsirkin
3ec7393a68 IPoIB/cm: Initialize RX before moving QP to RTR
Fix a crasher bug in IPoIB CM: once a QP is in the RTR state, a
receive completion (or even an asynchronous error) might be observed
on this QP, so we have to initialize all of our receive data
structures before moving to the RTR state.

As an optimization (since modify_qp might take a long time), the
jiffies update done when moving RX to the passive_ids list is also
left in place to reduce the chance of the RX being misdetected as
stale.

This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=662>.

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-21 13:03:50 -07:00
Roland Dreier
24bce50803 IB/umem: Fix possible hang on process exit
If ib_umem_release() is called after ib_uverbs_close() sets context->closing,
then a process can get stuck in a D state, because the code boils down to

	if (down_write_trylock(&mm->mmap_sem))
		down_write(&mm->mmap_sem);

which is obviously a stupid instant deadlock.  Fix the code so that we
only try to take the lock once.

This bug was introduced in commit f7c6a7b5 ("IB/uverbs: Export
ib_umem_get()/ib_umem_release() to modules") which fortunately never
made it into a release, and was reported by Pete Wyckoff <pw@osc.edu>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-21 11:05:58 -07:00
FUJITA Tomonori
da9c0c770e [SCSI] iscsi_iser: convert to use the data buffer accessors
iscsi_iser: convert to use the data buffer accessors

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

TODO: use scsi_for_each_sg().

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-18 19:48:43 -05:00
Roland Dreier
e61ef2416b IB/mlx4: Make sure inline data segments don't cross a 64 byte boundary
Inline data segments in send WQEs are not allowed to cross a 64 byte
boundary.  We use inline data segments to hold the UD headers for MLX
QPs (QP0 and QP1).  A send with GRH on QP1 will have a UD header that
is too big to fit in a single inline data segment without crossing a
64 byte boundary, so split the header into two inline data segments.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-18 09:23:47 -07:00
Roland Dreier
5ae2a7a836 IB/mlx4: Handle FW command interface rev 3
Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set.  Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-18 08:15:02 -07:00
Jack Morgenstein
082dee3216 IB/mlx4: Handle buffer wraparound in __mlx4_ib_cq_clean()
When compacting CQ entries, we need to set the correct value of the
ownership bit in case the value is different between the index we copy
the CQE from and the index we copy it to.

Found by Ronni Zimmerman of Mellanox.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-18 08:13:59 -07:00
Roland Dreier
54e95f8dcb IB/mlx4: Get rid of max_inline_data calculation
The calculation of max_inline_data in set_kernel_sq_size() is bogus,
since it doesn't take into account the fact that inline segments may
not cross a 64-byte boundary, and hence multiple inline segments will
probably need to be used to post large inline sends.

We don't support inline sends for kernel QPs anyway, so there's no
point in doing this calculation anyway, since the field is just zeroed
out a little later.  So just delete the bogus calculation.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-18 08:13:53 -07:00
Roland Dreier
0e6e741621 IB/mlx4: Handle new FW requirement for send request prefetching
New ConnectX firmware introduces FW command interface revision 2,
which requires that for each QP, a chunk of send queue entries (the
"headroom") is kept marked as invalid, so that the HCA doesn't get
confused if it prefetches entries that haven't been posted yet.  Add
code to the driver to do this, and also update the user ABI so that
userspace can request that the prefetcher be turned off for userspace
QPs (we just leave the prefetcher on for all kernel QPs).

Unfortunately, marking send queue entries this way is confuses older
firmware, so we change the driver to allow only FW command interface
revisions 2.  This means that users will have to update their firmware
to work with the new driver, but the firmware is changing quickly and
the old firmware has lots of other bugs anyway, so this shouldn't be too
big a deal.

Based on a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-18 08:13:48 -07:00
Roland Dreier
42c059ea2b IB/mlx4: Fix warning in rounding up queue sizes
Doing max(1, foo) where foo is u32 generates a warning, because 1 is a
signed constant.  Fix this by using 1U instead.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-12 10:52:02 -07:00
Roland Dreier
614c3c85b5 IB/mlx4: Fix handling of wq->tail for send completions
Cast the increment added to wq->tail when send completions are
processed to u16 to avoid using wrong values caused by standard
integer promotions.

The same bug was fixed in libmlx4 by Eli Cohen <eli@mellanox.co.il>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-12 10:50:42 -07:00
Linus Torvalds
99f9f3d49c Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mlx4: Make sure RQ allocation is always valid
  RDMA/cma: Fix initialization of next_port
  IB/mlx4: Fix zeroing of rnr_retry value in ib_modify_qp()
  mlx4_core: Don't set MTT address in dMPT entries with PA set
  mlx4_core: Check firmware command interface revision
  IB/mthca, mlx4_core: Fix typo in comment
  mlx4_core: Free catastrophic error MSI-X interrupt with correct dev_id
  mlx4_core: Initialize ctx_list and ctx_lock earlier
  mlx4_core: Fix CQ context layout
2007-06-11 15:46:08 -07:00
Roland Dreier
a4cd7ed86f IB/mlx4: Make sure RQ allocation is always valid
QPs attached to an SRQ must never have their own RQ, and QPs not
attached to SRQs must have an RQ with at least 1 entry.  Enforce all
of this in set_rq_size().

Based on a patch by Eli Cohen <eli@mellanox.co.il>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-07 23:24:39 -07:00
Sean Hefty
bf2944bd56 RDMA/cma: Fix initialization of next_port
next_port should be between sysctl_local_port_range[0] and [1].
However, it is initially set to a random value with get_random_bytes().  
If the value is negative when treated as a signed integer, next_port
can end up outside the expected range because of the result of the % 
operator being negative.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-07 23:24:38 -07:00
Jack Morgenstein
57f01b5339 IB/mlx4: Fix zeroing of rnr_retry value in ib_modify_qp()
The code in __mlx4_ib_modify_qp() overwrites context->params1 after
the RNR retry parameter is ORed in, which results in the RNR retry
parameter always being set to 0.  Fix this by moving where we OR in
the value to later in the function, after the initial assignment of
context->params1.

Found by the Mellanox firmware group.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-07 23:24:38 -07:00
Herbert Xu
42f811b8bc [IPV4]: Convert IPv4 devconf to an array
This patch converts the ipv4_devconf config members (everything except
sysctl) to an array.  This allows easier manipulation which will be
needed later on to provide better management of default config values.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-06-07 13:39:13 -07:00
Roland Dreier
3e1db334dc IB/mthca, mlx4_core: Fix typo in comment
s/signifant/significant/

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-07 11:51:59 -07:00
FUJITA Tomonori
bb350d1dec [SCSI] ib_srp: convert to use the data buffer accessors
- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-07 09:02:50 -05:00
Mike Christie
d8196ed218 [SCSI] iscsi class, iscsi_tcp, iser, qla4xxx: add netdevname sysfs attr
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:38:04 -04:00
Mike Christie
1548271ece [SCSI] libiscsi: make can_queue configurable
This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:34:46 -04:00
Mike Christie
77a23c21aa [SCSI] libiscsi: fix iscsi cmdsn allocation
The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.

This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:34:14 -04:00
Mike Christie
b2c6416736 [SCSI] iscsi class, iscsi_tcp, ib_iser: add sysfs chap file
The attached patches add sysfs files for the chap settings
to the iscsi transport class, iscsi_tcp and ib_iser. This is
needed for software iscsi because there are times when iscsid
can die and it will need to reread the values it was using.
And it is needed by qla4xxx for basic management opertaions.
This patch does not hook in qla4xxx yet, because I am not sure
the mbx command to use.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:58:58 -04:00
Mike Christie
857ae0bdb7 [SCSI] iscsi: Some fixes in preparation for bidirectional support - total_length
- Remove shadow of request length from struct iscsi_cmd_task.
- change all users to use scsi_cmnd->request_bufflen directly

(With bidi we will use scsi-ml API to retrieve in/out length)

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:58:22 -04:00
Mike Christie
8ad5781ae9 [SCSI] iscsi class, qla4xxx, iscsi_tcp, ib_iser: export/set initiator name
For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.

For hw iscsi, it is nice to see what the card is using.

This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:56:40 -04:00
Mike Christie
0801c242a3 [SCSI] libiscsi, iscsi_tcp, ib_iser : add sw iscsi host get/set params helpers
iscsid and udev need to key off the hw address being
used so add some helpers for iser and iscsi tcp.

Also convert them

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:55:23 -04:00
Sean Hefty
d998ccce02 IB/cm: Fix stale connection detection
The ib_cm can incorrectly detect a stale connection (a new connection
request for a QPN that is already connected) as a duplicate connection
request.  Separate the handling of potential duplicate REQs from stale
connections.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-29 16:07:09 -07:00
Michael S. Tsirkin
ec56dc0b7f IPoIB/cm: Fix performance regression on Mellanox
commit 518b1646 ("IPoIB/cm: Fix SRQ WR leak") introduced a severe
performance regression on Mellanox cards, because keeping a QP in the
error state for extended periods of time moves hardware to the slow
path (until the QP is destroyed).  For example, MPI latency goes from
~3 usecs to ~7 usecs.

Fix this by posting a send WR on one of the QPs that are being
flushed, instead of using a separate drain QP that is kept in the
error state.

This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=636>,
reported and bisected by Scott Weitzenkamp at Cisco and debugged by
Sasha Mikheev at Voltaire.

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-29 16:07:09 -07:00
Michael S. Tsirkin
8b7e15772a IB/mthca: Fix handling of send CQE with error for QPs connected to SRQ
mthca_free_err_wqe() currently treats both send and receive CQEs
identically if a QP is using an SRQ.  But for Tavor hardware, send
CQEs with error can be chained together even if the RQ is part of SRQ,
so we may miss some CQEs.

Fix by following the WQE chain for all send CQEs even for non-SRQ QPs.

This fixes crashes in IPoIB CM:
<https://bugs.openfabrics.org//show_bug.cgi?id=604>

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-29 16:07:09 -07:00
Michael S. Tsirkin
2dfbfc3712 IPoIB/cm: Drain cq in ipoib_cm_dev_stop()
Since NAPI polling is disabled while ipoib_cm_dev_stop() is running,
ipoib_cm_dev_stop() must poll the CQ itself in order to see the
packets draining.

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-24 14:02:40 -07:00
Michael S. Tsirkin
8fd357a6e3 IPoIB/cm: Fix timeout check in ipoib_cm_dev_stop()
time_after() was used backwards, so the timeout occurred immediately.

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-24 14:02:39 -07:00
Stefan Roscher
65a2c841d6 IB/ehca: Fix number of send WRs reported for new QP
Due to a typo, the driver was reporting the wrong number of "actual send
WRs" after ehca_create_qp().

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-24 14:02:39 -07:00